Gast 3D User Manual
70-2600 G447PL (Rev. A)
3D SERIES MINIATURE PUMP
OPERATION & MAINTENANCE MANUAL
Visit us at our website
www.gastmfg.com
This is the hazard alert symbol: m. When you see this
symbol, be aware that personal injury or property damage is
possible. The hazard is explained in text follo wing symbol.
Read this information carefully before proceeding.
The following is an explanation of three different
types of hazards:
m DANGER Severe personal injury or death
will occur if hazard is ignored.
m WARNING Severe personal injury or death
can occur if hazard is ignored.
m CAUTION Minor injury or property damage
can occur if hazard is ignored.
GENERAL INFORMATION
m CAUTION Required ambient temperature is -10˚F
to 150˚F. Operation at temperatures
outside this range will reduce pump life.
Lower atmospheric pressure at high altitudes lowers
performance. Consult a Gast distributor for details.
Never lubricate this oil-less pump. Sealed bearings are
grease-packed. Introducing petroleum-based or
hydrocarbon products will reduce service life of diaphragm
and valve.
INSTALLATION
m CAUTION Do not block flow of cooling air over
pump in any way.
Ensure that nothing will interfere with movement of
eccentric. While not dangerous, eccentric must move
freely to allow pump to operate properly.
Mounting
To reduce noise and vibration, use Velcro or a
vibration-isolated mounting surface.
Plumbing
To pr event airflow restriction, use an elastic hose of
same size as hose port. These ports are not designed
to support plumbing.
Filters
Avoid unfiltered operation in an environment
where there is visible airborne particulate material.
Use a suitable filter to avoid ingesting dirt/metal or
other foreign material into pump.
Wiring
m WARNING Poor wiring can result in electric shock.
Wiring must conform to all required safety
codes and be installed by a qualified
person. Refer to wiring diagram below .
Ensure that supply voltage agrees with pump
operating voltage. Remove power to pump if
motor fails to start or stops under load. Warming
pump to a minimum of –10˚F in extremely cold
weather will
ease starting
and extend
DC WIRING
RED/WHITE (+)
pump life.
M
BLACK
+
KEEP THIS DOCUMENT FOR FUTURE REFERENCE
TROUBLESHOOTING GUIDE
OPERATION
m CAUTION This unit is designed to pump gases
only. Ingestion of dirt, metal, water, or
petroleum-based contaminants will
reduce pump life.
4. Avoid ingesting dirt into pump.
Following these basic recommendations will avoid
damage to pump and may extend its operating life.
General recommendations for operation:
1. A void operating pump at temperatures less than –10˚F
or greater than 150˚F.
2. Draw through pump only those substances, which
do not react with EPDM or PPS (diagram material).
3. Avoid unfiltered operation in an environment where
there is visible airborne particulate matter.
MOTPMYSESUACELBISSOPKCEHCOTTNIOPYDEMER
tratSt'noW
evissecxE
esioN
lacirtcelE•
noitcennoC
egatloVwoL/gnorW•
muucaV/erusserP•
daeHno
egatloVgnorW•
gnibmulproesoH•
kael
MAINTENANCE
Do not attempt to replace connecting rod or motor
bearings. If after cleaning unit still does not operate
properly, contact your representative, or factory, or
return pump to an Authorized Service Facility.
EDIUGGNITOOHSELBUORT
eriwrogulpkcehC•
lacirtceleerusnE•
deilppussirewop
detcepsnidna
evlavfeilertcepsnI•
rewoptcepsnI•
ylppus
rofsesohtcepsnI•
skcarc
noitcennoc
reporpylppA•
egatlov
ecalperroteseR•
evlavfeiler
reporpylppA•
egatlov
esohecalpeR•
gnitaehrevO
erusserPwoL
muucaVwoL
AUTHORIZED SERVICE FACILITIES
Gast Manufacturing Inc.
2300 Highway M-139
Benton Harbor, MI 49022
TEL: 616-926-6171
FAX: 616-925-8288
www.gastmfg.com
Wainbee Limited
215 Brunswick Blvd.
Pointe Claire, Quebec
Canada H9R 4R7
TEL: 514-697-8810
FAX: 514-697-3070
Gast Manufacturing Inc.
505 Washington Avenue
Carlstadt, NJ 07072
TEL: 201-933-8484
FAX: 201-933-5545
Wainbee Limited
5789 Coopers Avenue
Mississauga, Ontario
Canada L4Z 3S6
TEL: 416-213-7202
FAX: 416-213-7207
retliFytriD•
hgiHrowoL•
egatloV
retliFytriD•
egatloVwoL•
Brenner Fiedler & Assoc
13824 Bentley Place
Cerritos, CA 90701
TEL: 800-843-5558
TEL: 310-404-2721
FAX: 310-404-7975
Japan Machinery Co., Ltd
Central PO Box 1451
Tokyo, 100-91 Japan
TEL: 81-3-3573-5421
FAX: 81-3-3571-7865
or: 81-3-3571-7896
retliftcepsnI•
rewoptcepsnI•
ylppus
retliftcepsnI•
rewoptcepsnI•
ylppus
egatlov
ytilicaf
Gast Manufacturing Co., Ltd.
Beech House, Knaves Beech
Business Centre, Loudwater
High Wycombe, Bucks HP 10 9SD
England
TEL: 44 628 532600
FAX: 44 628 532470
NOTE: General correspondence should be
Gast Mfr. Inc./A Unit of IDEX Corporation
P O Box 97
Benton Harbor, MI 49023-0097
retlifecalpeR•
reporpylppA•
retlifecalpeR•
reporpylppuS•
rewoplacirtcele
naottinudneS•
ecivresdezirohtua
sent to—
Loading...