Fadini Elpro 10F User Manual

Optional

Code 5578

BRAKE

CONTROL

STEP SWITCH

-

5 4 3 2 1

+

630mA

FUSE

POT. 80VA 50/60Hz

MOD. E010F

PRI: 400-230V

SEC: 24V - 1A

COMELIT

Made in Italy

276/25/06/C

400V - 24Vac

80VA TRANSFORMER

230V

VOLTAGE

CHANGE-OVER SWITCH

400V

BRAKE

CONNECTOR

FLASHING LAMP

1A

OPEN

ON

FUSE

LOGIC CARD

OFF

CLOSE MAINS

1A FUSE

24V OUTPUT

TERMINALS 12-13

DWELL

TIME

+

-

5A

FUSES

HIGH VOLTAGE

EARTH

CONNECTION

MOTOR RUN TIME

OPEN/CLOSE

+

-

12 3 45 6 78

NEUTRAL

23
2221

20

19

19
18

COMMON

17

16

15

14

13

12
11

10

96
85
74

3
2
1

Elpro 10

LIVE

N.C. SAFETY
CONTACT

24V OUTPUT max permitted load:
2 pairs photocells
1 radio receiver

24V INDICATOR - 3W max

LIMIT SWITCH. OPEN. N.C.

COMMON
LIMIT SWITCH. CLOSE. N.C.

RADIO CONTACT

N.C. CONTACT. STOP

N.O. CONTACT. CLOSE

N.O. CONTACT. OPEN

COMMON

N.C. CONTACT.
PHOTOCELLS

230V

SINGLE-PHASE

SUPPLY VOLTAGE

230V FLASHING LAMP - 25W max

M

ELECTRIC

SINGLE-PHASE

ELECTRIC LOCK
POWER OUTPUT

F

SLIDING GATES

THREE-PHASE / SINGLE-PHASE

M

230-400V

THREE-PHASE

SUPPLY VOLTAGE

THREE-PHASE

34

MOTOR

ELECTRIC

TIONS

21 22 23

MOTOR

2 PULSES: FULL OPENING

1 PULSE: PEDESTRIAN OPENING

PEDESTRIAN OPERATOR

DIP-SWITCH

ON

262728

TERMINALS FOR THE

CONNECTION OF THE

PUSH BUTTONS PULIN 3

GB

Drwg. No. 3339

ELPRO 10 F

MICRO-PROCESSOR

B

12 345678

CHANNEL

st

24V OUTPUT

1

RADIO CONTROL

PLUG-IN CARD SUPPORT

N.W.: should more pairs of photocells be required than the
recommended quantity, fit an auxiliary transformer outside the
control box.

N.W.:

for special application, ie. to switch on lights - CCTV etc...,
SOLID STATE RELAYS are recommended to be used only. Standard
relays would affect the micro-processor.

N.W.:

THIS PANEL IS TESTED TO OPERATE GATES ONLY THROUGH
FADINI ACCESSORIES, NO GUARANTEE FOR ACCESSORIES OF OTHER
MAKE OR SPECIAL APPLICATIONS.

ELECTRONIC PROGRAMMER
FOR SLIDING GATES. PEDESTRIAN OPENING.
HOLD ON SWITCHED CONTROL AND
ELECTRONIC BRAKE.

37

REVERSE

OPEN, CLOSE &

ALL OPERA

RADIO CONTACT

Elpro 10

F

FUNCTIONS OF THE ELECTRONIC PROGRAMMER FOR SLIDING GATES

All the electrical connections are to be made as per the following instructions and diagrams. Supply the terminals
21-22-23 with 230/400 V / 50 Hz, three-phase voltage. The "red led" No.1 switches on and stays on as long as the
board is properly supplied. Set the timer "MOTOR RUN. OPEN & CLOSE" so that the running time of the motor is longer
than the actual travel of the gate. Set the timer "DWELL" - i.e. the interval between open and re-close- so that you
can meet the required interval of time.
LOGIC OF THE ELECTRONIC PROGRAMMER: when a pulse is given, the flashing light switches on. After three seconds
the motor starts. During the interval before re-closing, the light stays on. When the gate has fully re-closed, the light
keeps on flashing for three more seconds and the switches off automatically. The 3 second interval (pre-flashing)
which precedes the actual start of the motor can be eliminated by means of the DIP-SWITCH B No. 4.

LED No. 1: It switches on when voltage is supplied.
LED No. 2: Photocells. Normally on. It switches off when the photocells are obstructed.
LED No. 3: Open. It switches on when the respective switch is activated.
LED No. 4: Close. It switches on when the respective switch is activated.
LED No. 5: Stop. Normally on. It switches off when the respective switch is activated.
LED No. 6: Radio. It switches on whenever a pulse is given, either through remote control, keyswitch or push buttons.
LED No. 7: Limit switch. Close. It switches off when the gate is fully closed.

LED No. 8: Limit switch. Open. It switches off when the gate is fully open.

DIP-SWITCH

ON

ON

B

1 2345 678

No. 1 ON = PHOTOCELLS. STOP DURING "OPEN" CYCLE
No. 1 OFF = PHOTOCELLS. NO STOP DURING "OPEN" CYCLE. REVERSE ON CLOSING.

No. 2 ON = REMOTE CONTROL. NO REVERSE TRAVEL ON OPENING
No. 2 OFF = REMOTE CONTROL. REVERSE TRAVEL

No. 3 ON = AUTOMATIC RE-CLOSING
No. 3 OFF = NO AUTOMATIC RE-CLOSING

No. 4 ON = PRE-FLASHING
No. 4 OFF = NO PRE-FLASHING

No. 5 ON = REMOTE CONTROL. STEP BY STEP. STOP IN BETWEEN
No. 5 OFF = REMOTE CONTROL. GATE CAN BE REVERSED WHILE TRAVELLING

No. 6 ON = "DEADMAN CONTROL" (HOLD-ON SWITCHED). SET No.3 TO OFF
No. 6 OFF = OUT OF SERVICE. NORMAL OPERATING MODE
"
switch button or key is hold on pressed or turned until
the end of the operation.

OFF

HOLD ON SWITCHED CONTROL": any open or close operations require that the respective

GENERAL DIAGRAM. DIP-switches No. 1  2  3  4  5  6

DIP-SWITCH

ON

B

1 2345 678

ELECTRONIC BRAKE TO FIT
ELPRO 10 F PROGRAMMER

- BRAKE FORCE ADJUSTMENT.

Force can be adjusted by means of a step
switch from one to five steps. (Optional)

GB

ON

OFF

ON

78

full

opening

SETTING FOR PARTIAL PEDESTRIAN OPENING. Dip-switches No. 7  8

A first "OPEN" pulse to terminal No.4 opens the gate to the distance set through
the switchs 7 - 8 as explained below; a second pulse opens the gate full travel.

meccanica

F

FADINI

Drwg. No. 3339

AUTOMATIC GATE MANUFACTURERS

ON

78

1 meter opening

Code 5578

ON

78

1.5 meter opening

-

+

5 4 3 2 1

BRAKE CONNECTOR

Via Mantova 177/A - 37053 Cerea (VR) Italy
Tel. [phone] - Fax [phone]
e-mail: [e-mail] - www.fadini.net

BRAKE CONTROL

STEP SWITCH

+

MORE POWER

2 meter opening

LESS POWER

54 21

ON

78

_

the gate opener

Made in Italy