Fadini DGT 61 User Manual

Download

Page 1

DGT 61

ENGLISH

Instructions Manual

Digital keypad

Instructions manual DGT 61 digital keypad

BRINGING THE KEYPAD APART

Treated

aluminium

front unit

Plastic back casing recess mount

BRINGING THE MAIN PCB APART

This unit is recommended to be installed in a

safe and sheltered place

meccanica

FADINI

Item 610

Surface keypad

Item 612

Main Printed Circuit Board

DGT 61

12-24V cc/ca

Item 611

Partial recess keypad

Stainless steel

front cover

Keypad

ACCESSORIES TO FIT THE KEYPAD, RECESS APPLICATION

STOP

code 552

code 558

SURFACE APPLICATION OF THE KEYPAD TO A WALL

STOP

DISPOSITIVO SONORO

NOTE: screws and expanding bolts not supplied by us.

SOUND DEVICE

Treated aluminium

back casing

surface mount

Prit 19

code 560

Pic.4

DGT 61

12-24V cc/ca

Pic.1

Sech 15

code 553

LED LIGHTS

T O

I N

GREEN LED:

access code OK

 Fixed light: - unit on voltage

- night illumination of the keypad  Flashing light: professionaly advanced timed functions

BLUE LED:

in progress

RED LED: wrong access code or STOP button activated

Pic.2

code 554

code 552

Pic.3

Pic.5

page 7

Directive 2003/108/CE

Disposal of electric and electronic material

DO NOT DISPOSE OF AS

NORMAL WASTE - HARMFUL

FOR THE ENVIRONMENT

the gate opener

made in Italy

Long Beep: a long beep confirms the correct access code sequence

n°1 short beep: is emitted whenever

a key button is pressed

n°3 short beeps: the access code

sequence is wrong

n°5 short beeps: memory clearing carried out

correctly

page 8

STOP

Pic.6

Page 2

STOP

FADINI

Instructions manual DGT 61 digital keypad

meccanica

FADINI

GENERAL DESCRIPTION

DGT 61 is a custom-encoded control accessory designed to open and close any automatic access system. It can be also used to control other external applications. DGT 61 consists of a Key pad (in an anti-corrosion treated aluminium casing, in two options either to be partially recessed or sur face mounted) cable connected (x 4 wires) to the Main PCB; this one is to be installed near the Elpro electronic control box for the electrical connections. The keypad incorporates the button keys, illuminated in blue from the back: nine digits, two outputs A and B and one output for the emergency stop button. The main PCB is fitted with a terminal block where power supply is to be connected (in parallel also to the keypads), with the N.O. contacts of the A and B output relays and with one pure N.C. terminal output of a third relay, providing connections for an emergency stop. A second block of terminals X and Y (and a third one Z for long distance or disturbed signals) receive the encoded signal from the keypads. Programming is simple and immediate by Dip-switches on the main PCB. Each channel can take up to 4 different numerical codes; any one code, through the same channel either A or B, operates the same function. Other professionally advanced functions can be achieved by the two relays (bistable outputs, timed bistable outputs, output delay, etc.), and can be enabled by the Dip-switches on the main PCB. Other external control applications are also made possible (eg. illumination, alarm systems and watering) besides automatic door/gate systems, etc. In these cases, it is recommended that a relay be always fitted between the PCB and the other possible applications.

Red led 1: It flashes during programming phase

Red led 2: It flashes slowly when X Y are properly connected to the keypad

Jumper for 12Vdc power supply: when jumper is fitted, 12Vdc power supply is possible

Automated access A or

other applications

12-24Vac/dc

1st CODE to relay A

2nd CODE to relay A

3rd CODE to relay A

4th CODE to relay A

Main PCB

12345678910

OFF

CNO NOCNCC

1**

2**

3**

4**

relay NO

relay NCrelay NO

1**

2**

3**

4**

(*) the connection to the Z terminal is required in

case of weak or

disturbed signal

(*)

max 0.5mm² up to 100m

XYZ

= Pure contact for STOP function only: direct to

the relay in case of an emergency

1st CODE to relay B

2nd CODE to relay B

3rd CODE to relay B

4th CODE to relay B

**once encoding/programming phases are completed, all Dip-switches are to be set to OFF

456

789

STOP

12-24V

ac/dc

ingresso

automatizzato B o

altre utenze

1 or more keypads DGT 61

Pic.7

DIAGRAM OF A POSSIBLE INSTALLATION WITH TWO KEYPADS AND ONE PCB

DGT 61

AB V 4

-2 2 1

a /c c

12345678910

OFF

CNO NOCNCC

24V

ac/dc

0.5mm² up to 100m

main PCB

open

456

789

XYZ

relay

open

Keypad DGT 61 Keypad DGT 61

STOP

XYZ

(*)

12-24V

ac/dc

(*)

XYZ

NCrelay N0relay N0

max 0.5mm²

up to 100m

(*) The connection

to Z terminal is

required in case of

weak or disturbed

stop

13 13

XYZ

signal

12-24V

ac/dc

456

789

STOP

Controll box series

Elpro - access A

Controll box Elpro 6 -

access B

(*)

3 4 6

common

open

stop

13 14

24Vac/dc

3 4

common

open/stop/close

Pic.8

page 9 page 10

Instructions manual DGT 61 digital keypad

STORING ONE OR MORE ACCESS CODES ONTO THE RELAY OUTPUT A

1) Carry out the electrical connections to the MAIN PCB (Pic.8).

2) Set

only one of the switches DIP 1 or DIP 2 or DIP 3 or DIP 4 to ON (It is through the first four DIp-switches that different ACCESS CODES can be stored). The red led 1 on the main PCB flashes.

3) Press the ACCESS CODE (from 1 to 6 digits) - press A. The green led goes on followed by a long confirming beep.

4) Set all DIP-switches to OFF. The red led 1 on the PCB goes off.

NOTE: The relay A can take up to 4 different access codes max. Each code is to be stored individually by setting any one of the first 4 DIP-switches to ON.

Diagram

1) 3) 4)

Main PCB

456

789

ACCESS

CODE

relay A

STORING ONE OR MORE ACCESS CODES ON O THE RELAY OUTPUT B

1) Carry out the electrical connections to the MAIN PCB (Pic.8).

2) Set

only one of the switches DIP 1 or DIP 2 or DIP 3 or DIP 4 to ON (It is through the first four DIp-switches that different ACCESS CODES can be stored). The red led 1 on the main PCB flashes.

3) Press the ACCESS CODE (from 1 to 6 digits) - press B. The green led goes on followed by a long confirming beep.

4) Set all DIP-switches to OFF. The red led 1 on the PCB goes off.

NOTE: The relay B can take up to 4 different access codes max. Each code is to be stored individually by setting any one of the first 4 DIP-switches to ON.

Diagram

1) 3) 4)

Main PCB

456

789

ACCESS

CODE

relay B

HOW TO OPERATE WITH DGT 61 KEYPAD

Once satisfied that the main PCB is properly connected to the Elpro control box, and the selected ACCESS CODES stored with the required output, to operate with the keypad just press the keys corresponding to the ACCESS CODE, followed by the key corresponding to the required OUTPUT (A or B). The green led goes on followed a long confirming beeping.

If the access code sequence is incorrect: the unit gives out 3

beeping souds and the red led illuminates for 2 seconds. Dial correctly or reprogram the unit.

n°3 short beeps

Red led

for 2 seconds

Diagram

456

789

ACCESS

CODE

oppure

A or B output

LON G

BEEPING

ENABLING THE STOP BUTTON KEY

Carry out the electrical connections to the keypad, main PCB and the Elpro control box (or to a control relay). Pic. 8. The DGT 61 keypad incorporates also a pure NC contact to get the STOP function. The contacts of the C - NC terminals on the main PCB are opened on pulsing the STOP button in the keypad, and no code is required to be entered.

Diagram

STOP

pure contact

NCC

Main PCB

press

red led

for 2 seconds

MEMORY CLEARING

PLEASE NOTE: THIS OPERATION ERASES COMPLETELY ALL THE ACCESS CODES AND ANY ADDITIONAL FUNCTIONS STORED WITH THE RELAY

INVOLVED IN THIS PROCESS.

1) Set the Dip-sw. 10 to ON. The red led 1 flashes.

2) Press the key 9 9 9 (three times).

3) Press button A or B to erase the encoding and the functions from output A or B

4) Set all the DIP-switches to OFF.

5 short beeps confirm the operation while the green led keeps flashing as long as beeping can be heard.

Diagram

Main

PCB

9 9 9

keypad

A or B output

ALL DIP-SW.

TO OFF

OFF

main PCB

n°5 Beeps

meccanica

FADINI

ALL DIP-SW.

TO OFF

OFF

Main PCB

ALL DIP-SW.

TO OFF

OFF

Main PCB

green led

for 1 second

green led

Page 3

STOP

FADINI

Connect the main PCB to the control box (Pic. 8) or to the external control relay, then store an access code with required outputs. Different functions can be achieved by one or both of the outputs, but different access codes to one relay carry out the same function. NOTE WELL: functions are reset in case of a power failure, even if instantaneous.

OUTPUT DELAY

The pulse is delayed (for a number of minutes) after pressing the access code.

Programming:

1) Set DIP-sw. 5 to ON. The red led 1 on the PCB flashes.

2) Press the number of minutes corresponding to the activation delay as required (max.1439 minutes).

3) Press output A or B through which the required function is activated.

4) Set all the DIP-switches to OFF Confirmation of the operation: long beep and green led alight for 2 sec.

Using the function:

Press the access code followed by A or B as programmed. The green led goes on for 1 sec. followed by an activation beep. The blue led starts flashing and indicates that the function has been activated.

TIMED WITH 2 PULSES

A pulse is given after the access code has been pressed and another one is given after a set time (minutes)

Programming:

1) Set DIP-sw. 6 to ON. The red led 1 on the PCB flashes.

2) Press the number of minutes for the time required after the first pulse (max. 1439 minutes).

3) Press either A or B output by which the function is to be activated.

4) Set all the DIP-switches to OFF. Confirmation of the operation: long beep and green led alight for 2 sec.

Using the function:

BISTABLE

Each pulse by the access code energizes or de-energizes the output relay.

Programming:

1) Set DIP-sw. 7 to ON. The red led 1 on the PCB flashes.

2) Press only the button key No. 7.

3) Press either A or B output by which the required function is to be actived.

4) Set all the DIP-switches to OFF Confirmation of the operation: long beep and green led alight for 2 sec.

Using the function:

Press the access code followed by A or B as programmed. The green led goes on for 1 sec. followed by an activation beeping.

TIMED DELAY WITH 2 PULSES

Each pulse by the access code delays (for a number of minutes) the energizing of the timed relay.

Programming:

1) Set DIP-sw. 8 to ON. The red led 1 flashes.

2) Press the number of minutes for the delay with time 1 (max 1439 minutes)

3) Press either A or B output by which the required function is to be activated.

4) Press the numer of minutes for time 2 (max. 1439 minutes).

5) Press ether A or B as set in step 3).

6) Set all the DIP-switches to OFF. Confirmation of the operation: long beep and green led alight for 2 sec.

Using the function:

Instructions manual DGT 61 digital keypad

ADDITIONAL FUNCTIONS: can be achieved by the A and B outputs through one or more access codes

pulse

output

pulse

output

pulse

output

pulse

output

Time

Time 1

Time

Time 2

Diagram

main PCB

In order to RESET (the function is cancelled) press the following sequence: A or B - access code - A or B

The green led goes on for 1 sec. followed by a confirmation beep, while the blue led stays illuminated.

Diagram

main PCB

In order to RESET (the function is cancelled) press the following sequence: A or B - access code - A or B

The green led goes on for 1 sec. followed by a confirmation beep, while the blue led stays illuminated.

Diagram

main PCB

Diagram

main PCB

In order to RESET (the function is cancelled) press the following sequence: A or B - access code - A or B

The green led goes on for 1 sec. followed by a confirmation beep, while the blue led stays illuminated.

2) 3)

456

789

time in minutes

(max 1439 = 24h)

2) 3)

456

789

time in minutes

(max 1439 = 24h)

2) 3)

press key 7

2) 3)

time 1 in

minutes

(max 1439)

keypad

keypad keypad

output

time 2 in

minutes

(max 1439)

page 11

meccanica

FADINI

ALL DIP-SW.

TO OFF

OFF

main PCB

ALL DIP-SW.

4) TO OFF

OFF

main PCB

ALL DIP-SW.

4) TO OFF

OFF

main PCB

ALL DIP-SW.

TO OFF

OFF

output

DGT 61

-2 2 1

a /c c

Main PCB

meccanica

FADINI

ALL DIP-SW.

TO OFF

OFF

main PCB

ALL DIP-SW.

TO OFF

main

PCB

Pic.9

the gate opener

made in Italy

OFF

Instructions manual DGT 61 digital keypad

ADDITIONAL FUNCTIONS: can be achieved by the A and B outputs through one or more access codes

TIMED BISTABLE

The relay is energized and remain energized for the time as set (in minutes).

Programming:

1) Set DIP-sw. 9 to ON. The red led 1 on the PCB flashes.

2) Press the number of minutes corresponding to the activation time as required (max. 1439 minutes).

3) Press output A or B as required for the function to be activated.

4) Set all the DIP-switches to OFF. Confirmation of the operation: long beep and green led alight for 2 sec.

Using the function:

REMOVING THE ADDITIONAL FUNCTIONS

Steps to cancel the additional functions from the single relay and set the DGT 61 unit back to normal functioning.

1) Set DIP-sw. 5 to ON. The red led 1 on the PCB flashes.

2) Press A (or B) - access code - press A (or B).

3) Set all the DIP-switches to OFF. Confirmation of the operation: long beep and green led alight for 2 sec.

OVERALL DIMENSIONS

Ø56

29 25

Recess mount keypad

TECHNICAL DATA

Power supply 2x0.5mm² Connections to the keypad Keypad absorption

Stand-by relay absorption Energized relay absorption Working temperature N.O. channels N.C. channels Communication distance Output contacts kaypad protection standards PCB protection standards

The manufacturer reser ves the right to change this manual without prior notice, and is not liable for incorrect applications or damages to persons and properties.

pulse

output

456

789

Keypad

12-24Vdc/ac 4 x 0.5mm² 15 mA 4 mA 27 mA

-20° +80°C 2 1 max 100 m 1A-125V-60VA IP 54 IP 53

Time

Manufacturing company:

The model:

DGT 61 is a digital keypad designed to be sold and installed into a comprehensive "Automatic System", including the original accessories and components as recommended by the Manufacturing Company. The installer must issue the Installer's Declaration of Conformity and carry out all the tests required to comply with the existing regulations. The manufacturing company is not liable for any incorrect use of its product. The product conforms with the following norms as specified below:

- Low Voltage Directive

- Electro-magnetic Compatibility Directive

Diagram

main PCB

In order to RESET (the function is cancelled) press the following sequence: A or B - access code - A or B

The green led goes on for 1 sec. followed by a confirmation beep, while the blue led stays illuminated.

Diagram

main

PCB

LONG BEEP

2) 3)

456

789

time in minutes

(max 1439 = 24h)

output access

gree led

for 2 seconds

Surface mount

keypad

456

789

code

output

DECLARATION OF CONFORMITY

of the manufacturer

meccanica

FADINI

DECLARES UNDER ITS OWN RESPONSIBILITY THAT:

Via Mantova 177/A - C.P. 126 - 37053 Cerea (VR) Italy Tel. +39 0442 330422 - Fax +39 0442 331054 e-mail: info@fadini.net - www.fadini.net

DGT 61

2006/95 CE 2004/108/CE and 92/31 CEE

Meccanica Fadini s.n.c.

Direttore Responsabile

20 - 04- 11

Date:

The responsible manager

page 12