Model 7300
INSTALLATION MANUAL
APOLLO Gate Operators, Inc.
Model 7300ETL-IL
08/18/09
Residential & Heavy Duty Commercial Slide Gate Operator
2
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .......................................................... 3
Applications .................................................................................................... 4
Pre-Installation Checklist ................................................................................ 5
Parts Identification .......................................................................................... 6
Pad Installation ................................................................................................ 7
Operator Installation ........................................................................................ 8
Chain Bracket Installation ............................................................................... 9
Chain & Chain Bolt Installation ....................................................................... 10
Chain Magnets Installation .............................................................................. 11
Left or Right Hand Operation …………………………………………………….. 12
Quick Release Operation .................................................................................. 13
Programming Instructions …………………………………………………………. 14
Control Board Connections ............................................................................. 15
Siren Connection ……………………………………………………………………. 22
Radio Receiver Options ……………………………………………………………. 23
Warranty ........................................................................................................... 24
3
WARNING - To reduce the risk of injury or death:
READ AND FOLLOW ALL INSTRUCTIONS.
Installation should be performed by a professional installer.
Required welding should be performed by a qualified welder.
Should electricity be required, use a certified electrician only.
Any device that requires 120 Volts AC should be U.L. approved.
Review with the owner all safety concerns including:
Do not operate the gate unless area around gate is in full view.
Never let children operate or play with gate controls. Keep the remote control
away from children.
Always keep people and objects away from the gate. NO ONE SHOULD CROSS
THE PATH OF THE MOVING GATE.
Periodically test the obstruction sensitivity to assure safe and proper
operation. Do not test sensitivity by standing between the gate and the hinge or
stop post.
The “CAUTION AUTOMATIC GATE” signs should be clearly visible from both
sides of the gate.
Always insure that the gate has closed securely before leaving area.
Arrange with local fire and law enforcement for emergency access.
Use the emergency release only when the gate is not moving.
A secondary entrapment device such as loop detectors, edge switches, and beam
detectors are highly recommended and required to meet the UL325 standard.
Install control devices such as keypads far enough away (5 feet or further) from any
moving parts of the operator and gate to prevent possible injury.
Do not install control box where the gate can come in contact with person using the
push button on side of control box.
Always disconnect the battery or power source when making adjustments or repairs to
any part of the gate or operator.
All rollers should be covered to prevent injury.
KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual. Have a qualified
service person make repairs to gate hardware.
The entrance is for vehicles only. Pedestrians must use separate entrance.
Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or
stop when an object activates the non contact sensors. After adjusting the force or limit of
travel, retest the gate operator. Failure to adjust and retest the gate operator properly can
increase the risk of injury or death.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
4
APPLICATIONS
The Apollo Model 7300ETL Slide Gate Operator is designed to handle a slide gate
up to 32 feet in total length (30 foot gate with 3 foot tail) and 1,000 lbs. A professional
fence or gate dealer is recommended to assure proper installation.Apollo Gate
Operators are available only through qualified dealers with an outstanding reputation
in the fence and gate industry. These dealers will be able to recommend the proper
equipment for particular applications. Apollo Gate Operators are 12 Volt DC (Direct
Current) powered. A 12 Volt sealed battery (33 ampere hour minimum) is
recommended. There are several advantages with 12 Volt DC systems:
Low voltage virtually eliminates risk of electrical shock.
Battery powered operators provide up to 200 operations in the event of
power outages.
The battery may be recharged with a trickle charger or by solar energy
(Electrical battery chargers should have a class 2 transformer rating).
If a trickle charger is used and a standard electrical outlet is not readily available, a
licensed electrician will be required for proper electrical hook up.
The following table should be used as a guide for capacity of operation of operators
only, additional options may reduce the the daily usage. Please note that the charge
capability of solar panels will vary with different geographical locations. All solar panels and battery chargers are designed for use with a 12 volt battery.
Daily Cycles 1-10 1-20 1-40 1-60 1-80 80+
5 watt solar panel
*
10 watt solar panel
*
20 watt solar panel(requires 5310 regulator)
*
30 watt solar panel(requires 5310 regulator)
*
40 watt solar panel(requires 5310 regulator)
*
1.5 amp battery charger
*
10 amp battery charger
*
Note: Double the amount of solar panels for Dual Gate Operators.
5
PRE-INSTALLATION CHECKLIST
The following checklist should be used before beginning installation:
• Verify that the proper operator has been selected for this application.
• Verify proper installation and operation of the gate.
1. Are all rollers covered with a protective housing?
2. Are the rollers servicable?
3. Does the gate roll free and level?
4. Will the gate require a locking device?
5. Are the main posts sturdy enough to handle the gate & operator?
• Determine the general location of the operator, chian brackets, and solar
panel (if used).
1. Is there a suitable location for the operator?
2.Can the solar panel (if used) be mounted in an unobstructed area facing
south?
3. Will additional solar panel cable be required?
4. Is electricity available (if required)?
• Consider safety and access options. Recommend if needed.
1. Will there be chidren or animals in the area?
2. Are safety loops, edge switches, or photo beam detectors required?
3. How can the gate be opened in emergencies?
4. How will visitors enter and exit?
5. Will vehicles (and trailers) have sufficient room off roadway to operate any
control devices such as keypads?
6
PARTS IDENTIFICATION
Chain Brackets (2)
#40 Roller Chain (35 feet)
Tie Wraps (4 each)
Master Chain Links (2 each)
Operator
5/16 Washers, Lock
Nuts, & Nuts (8 each)
5/16 U Bolts (4 each)
Chain Bolts with hardware (2 each)
#404C
Automatic Battery Charger (optional)
#201
5 Watt Solar Panel & Bracket
(optional)
#273G
CAUTION Signs (2 each)
7
PAD INSTALLATION
Pad Location
Driveway
Direction of Opening
12” 24”
24”
5”
Fig. A
Fig. B
Conduit requirements should be considered in the planning stage. If electrical power is required, a
separate conduit should be installed for electrical only. A certified electrician should be consulted for
the proper conduit material (Figure C & D).
Fig. C
AREA FOR CONDUIT
ENTRY
3”
14”
5”
Fig. D
Pad Location
8
OPERATOR INSTALLATION
Chain path
(Make sure
the chain
path clears
all posts and
obstacles).
TOP VIEW
Four 1/2” anchor bolts (not supplied) are
recommended to mount the chassis. The
holes should be drilled with a 1/2”
concrete drill bit.
STEP 1. Set the operator on the pad as shown. Align the sprockets 3 to 5 inches from the inside
surface of the gate.
STEP 2. Mark the four mounting holes on the pad.
STEP 3. Remove the operator and drill the holes according to the anchor bolt manufacturers in-
structions.
STEP 4. Replace the operator and fasten to the pad.
Mounting Holes
(4)
3”-5”
9
CHAIN BRACKET INSTALLATION
STEP 1. Assemble chain bracket with 5/16” U-bolt & hardware to each end of the gate as shown.
Do not tighten at this time.
STEP 2. Align the left chain
bracket slot with the top teeth
of the idler sprocket.
Idler Sprocket
Main Sprocket
STEP 3. Align the right
chain bracket slot with the
bottom teeth of the main
sprocket.
STEP 4. Tighten all hardware.
TIP: If welding equipment is
available, tack weld the chain
bracket to the gate on each
end to prevent slippage.
10
CHAIN & CHAIN BOLT INSTALLATION
STEP 1. Position the gate so that the operator is in the center of the
gate. Connect chain bolt to the chain bracket as shown on both ends of
the gate.
STEP 2. Attach the chain to the chain bolt using the master chain link. Do not
tighten the chain bolts .
Note: A chain breaking tool may
be required to reduce the chain to
the proper length.
11
Step 1. Press LED Enable once on the
right side of the circuit board. The STOP
LED should illuminate. This is a standard
condition.
Internal Limit Adjustment
Step 3. Activate the gate until the CLOSED LIMIT
LED is illuminated
Limit adjustment for left
movement
(gate moving to the left)
- less travel
- more travel
Limit adjustment for right.
Movement
(gate moving to the right)
- less travel
- more travel
Step 4. Adjust the corresponding limit switch for preferred
close position.
Step 5. Repeat steps 3 & 4 for setting the open limit
TIP: If the limits require extensive adjustment use a 13/32” or 25/64” socket with a portable drill
for course adjustment, then adjust manually for fine adjustment.
Step 2. Turn switch #1 OFF on the control board
12
Left or Right Hand Operation
operator
Gate in closed position
operator
Gate in closed position
Wiring Instructions
STEP 1. Determine which direction the gate will open. The factory units are plugged into INPUT B
for right hand opening as shown in Fig. 1.
For left hand opening, disconnect from INPUT B and plug intoINPUT A on the surge
board as shown in Fig. 2.
Fig. 1
Right Hand Opening
Fig. 2
Left Hand Opening
Right Side Installation
Red
Black
Green
Orange
White
Left Side Installation
Red
Black
Green
Orange
White
13
QUICK RELEASE OPERATION
Engaged
Engaged
Pull & turn 1/2 inch to disengage
14
STEP 7 Programming Current Sensing
The 835/836 control boards incorporate a safety feature that will put the operator into a hard shutdown mode if the control board detects a current sense
two consecutive times during a cycle. This hard shutdown condition can only
be reset by shorting the FIREBOX or UL connectors on the left side of the
control board to ground. This condition may also be reset by pressing the
HARD SHUTDOWN RESET button located toward the upper right hand corner of the control board. If a firebox is used in the installation, The firebox
door (optional) should be opened and closed to reset the control board.
The following instructions must be followed at installation for proper safety assurance.
All limits should be set before beginning this procedure.
This new procedure applies to revision 31 or higher firmware.
1. Press and hold the LED ENABLE button for five seconds. The STOP LED will blink
indicating that the board is in learn mode.
3. Cycle gate for 3 full cycles. The STOP LED will stop blinking indicating that the board
is now ready for normal operation
4. Test the auto reverse sensitivity to ensure maximum safety protection. The current
sensitivity adjustment pot may be adjusted to decrease or increase sensitivity.
8. Refer to the 835/836 Operator Control Board Manual to set other options such as
program switch options and close timer adjustments.
Installation is now complete.
Note: Program switch #9 is no longer functional and the current sense may be readjusted
at any time.
CLOCKWISE
Less sensitivity
Gate is harder to
current sense
COUNTER CLOCKWISE
More sensitivity
Gate is easy to current
sense
15
APOLLO Gate Operators, Inc.
835/836 Gate Control Board
Firmware Version 31 and up
Rev F
07/15/2005
16
PROGRAMMING INSTRUCTIONS
Once the operator is installed or if the control board is replaced, you will need to program
the control board for proper current sensing. The operator should be functional and the
open and close limits set.
1. Push and hold the LED ENABLE button for five seconds.
The “STOP” LED will blink indicating the board is in learn mode.
2. Cycle the gate three full times (must read open and close limit switches each cycle).
The “STOP” LED will now stay illuminated.
3. Adjust the current sensitivity pot to insure safe operation
The current sensitivity may be readjusted at any time without relearning the board.
Periodically check the current sensitivity for safe operation.
17
LED Enable & Learn
Mode Push Button
Optional Device Inputs
Stop Circuit Jumper
Fire & ETL Inputs
Emergency Bypass
Reverse Battery Polarity
Indicators
Optional Device Input
Remote Monitor Outputs
and Photo Eye
GateLink Connector
Microprocessor
Timer To Close -
Dual Gate Delay -
Current Sensitivity -
Adjustments
Program Switches
835/836 Control Board Parts Identification
Actuator Connector
(Master)
Actuator Connector
(Slave)
Control Board Reset
Hard Shutdown Reset
Operate Push Button
18
Board Actuator Function
Cable
Pin 1 Orange Open Limit
Pin 2 White Close Limit
Pin 3 Black Motor (positive on open, negative on close)
Pin 4 Red Motor (negative on open, positive on close)
Pin 5 Green Common for both limit switches
Pin 6 Yellow Feedback from intelligent actuator(816E/816EX)
Pin 7 Black Battery Negative
Pin 8 Red Battery Positive
1
3
5
7
2
4
6
8
Actuator Connector
Applies battery voltage directly to motor to open gate if
control board fails. User must unplug before gate opens
to maximum travel or 15 amp fuse will open. Fuse
should be checked before returning gate to service.
EMERGENCY BYPASS (open only)
Photo eye / safety loop wiring. Connect the positive power wire of the accessory to
12V. Connect the ground wire of the accessory to MAS (upper right area of the
835/836 board). Connect the relay wires of the accessory as normal: COM to GND.
NO to SAFETY (#14) (for a safety device). When the gate operator begins opening
(comes off of the closed limits) the MAS terminal will become a ground and will
complete the flow of power to the accessory. This will power the accessory up and it
will work as normal until the gate gets closed and the MAS terminal switches and the
device will power down.
Photo Eye Hookup
12V Supplied battery voltage
MAS Master Operator Indicator (indicates master side of gate is closed)
+12V when on closed limit. Ground when off of closed limit.
SLV Slave Operator Indicator (indicates slave side of gate is closed)
+12V when on closed limit. Ground when off of closed limit.
GND Battery supplied ground
SIREN Connect to siren +
applies +12V when gate(s) are running, or in hard shutdown
GND Battery supplied ground
LOCK Connect to lock + (optional) Magnetic or Solenoid type locks (Dip Switch #6 Selectable)
Remote Outputs and Photo Eye Hookup
19
Adjustments
Push Buttons
TIMER TO CLOSE Adjusts time before gate automatically closes
Adjustable 5 to 70 seconds.
DUAL GATE DELAY Adjusts delay between master and slave op-
eration 0-4 seconds (836 only for use with
magnetic, solenoid, and other locking de
vices)
CURRENT SENSITIVITY Increases or decreases the Auto Reverse
sensitivity.
LED ENABLE When depressed, activates LEDs for 15
minutes to assist in installation and troubleshooting.
Hold the push button down for five seconds to put
the board in program mode.
RESET Resets the microprocessor. Returns processor to
last known state.
OPERATE When depressed, activates the gate. Used for initial
installation and testing.
Hard Shutdown Reset Resets the operator when the gate current
senses twice before fully opening or closing.
Jumpers
STOP CIRCUIT JUMPER When the STOP CIRCUIT
program switch #5 must be ON JUMPER is connected, the gate
will operate normally.
STOP CIRCUIT JUMPER When a 3-button station is con-
program switch #5 must be OFFnected to the board, the STOP
CIRCUIT JUMPER must be removed.
20
Program Switches
OFF ON
1 TIMER TO CLOSE Gate does not automatically close. Gate automatically closes.
2 TIMER TO CLOSE OPT. Gate automatically closes from Gate automatically closes only when completely
any position after opening. open (open limit engaged).
3 SLAVE DISABLE Enables slave side (dual gate use). Disables slave side. (single gate use)
4 SIREN DELAY Siren (optional) active when gate is Siren (optional) starts 5 seconds before gate moves.
moving.
5 ‘STOP’ CIRCUIT ENABLE Must hold down open or close Normal operation
buttons to move gate. Gate stops Momentary open or close input runs gate to limit.
when button released.
6 LOCK TYPE For 12V mechanical (solenoid) locks. For 12V magnetic locks.
(+12V for 4 seconds on open cycle) (+12V when on close limit)
7 COAST ENABLE Gate will stop immediately when at Gate will coast (minimally) when it reaches limits.
Open or Close limit Recommended for 7500 slide operator only.
8 FREE EXIT OPT. A free exit input will open gate from A free exit input will open gate from any
closed position or after a close cycle position after an open or close cycle.
only.
9 DUAL GATE SYNC Both gates operate at normal This feature will control the master gate to open
Speed (slave slower than or close at the same speed as the slave gate.
Master).
10 SMART ACT. Off for 416E & 416EX actuators, Used for 816E & 816EX actuators only
slide gates, 3500 or when slow down (soft start & stop).
feature is not desired.
21
GND Supplied Battery Ground
INP Activate Gate (Push button activation when momentarily shorted to ground)
12V Supplied Battery Voltage (Protected with 3 Amp fuse)
GND Supplied Battery Ground
INP Activate Gate (Push button activation when momentarily shorted to ground)
12V Supplied Battery Voltage (Protected with 3 Amp fuse)
EDGE Reverse edge input. When grounded, will stop and reverse gate if closing, resets close timer if gate is open.
EDGE Reverse edge input. When grounded, will stop and reverse gate if closing, resets close timer if gate is open.
GND Supplied Battery Ground
GND Supplied Battery Ground
STOP Stop input from a 3 button station (must remove STOP CIRCUIT JUMPER) Normally closed
CLOSE Close input from a 3 button station (see program switch #5 for options)
OPEN Open input from a 3 button station (see program switch #5 for options)
GND Supplied Battery Ground
GND Supplied Battery Ground
FREE EXIT Opens gate if closed, stops and reverses gate if closing, resets close timer if gate is open.
GND Supplied Battery Ground
SHADOW Resets close timer when gate is open (also referred to as under gate loop)
GND Supplied Battery Ground
SAFETY Resets close timer if gate is open, stops and reverses if gate is closing. (Does not open a closed gate)
GND Supplied Battery Ground
FIRE When grounded, opens gate and holds gate open until released.
Clears “Hard Shutdown” mode of software.
UL When grounded, opens gate and holds gate open until released.
Clears “Hard Shutdown” mode of software.
Optional Device Inputs
GND Supplied Battery Ground
INP Activate Gate (Push button activation when momentarily shorted to ground)
12V Supplied Battery Voltage (Protected with 3 Amp fuse)
22
APOLLO Gate Operators, Inc.
911 Siren
Mount siren in an area that will produce maximum performance (additional wire may be required).
Connect the red wire to the SIREN connector on the Remote Monitor Output Connector block.
Connect the black wire to the GND connector on the Remote Monitor Output Connector block.
Red
Black
Set Program Switch # 4 as preferred:
ON - Upon activation, Siren will start for 5 seconds before gate(s) begin moving.
OFF - Siren and gate(s) start immediately upon activation.
The 911 Siren is included with all Apollo ETL Gate Operators.
23
APOLLO Gate Operators RECEIVER OPTIONS
Do not confuse the receiver code switches with the red program switches on the gate control board.
Never set all code switches to the same position. Transmitters must match code switches for proper operation.
If power is taken directly from battery or connected as shown below, receiver should be configured for 12VDC
Multi-Code/Digi-Code
Allstar
Lift-Master*
black
gray
gray
red
white
black
red
4
3
2
1
Heddolf
Linear
black
yellow
red
white/silver
common
n/o
white/gold
white
* Lift-Master will require that the 12/24 jumper be set to 12 and the C/M (constant/momentary) jumper be set to C
24
The Apollo 835/836 board is the standard board in all ETL compliant Apollo Gate Operators. Single gate systems use the 835 board (distinguished by MASTER and EMERGENCY BYPASS modular receptacles) and DUAL gate systems use the 836 board
(distinguished by MASTER, SLAVE and EMERGENCY BYPASS receptacles). The 836
board may be used in single gate applications by simply turning PROGRAM SWITCH #3
to the OFF position and only using the MASTER receptacle of the board. Apollo 7000
ETL and 7100 ETL systems use a Stature Electric direct current motor while the Commercial 7200 ETL and 7300 ETL use a Bison direct current motor. Both motors are similar in design and thus trouble shooting for all of the slide gate systems is covered in one
manual. Keep in mind that SLIDE GATE operators do NOT utilize the “SMART ACTUATOR” feature of the 835/836 board so Program switch #10 must ALWAYS be in the OFF
position. Trouble Shooting the Apollo 7000/7100/7200/7300 ETL systems:
1. Check your battery! The battery in your gate operator is the power source for the
entire system. If it is not adequately charged, the system will not operator properly.
Test the battery by checking the voltage with a volt-meter while the battery is under load (gate operating). For AC charged systems – unplug the battery charger
before load testing battery. Battery voltage should be 11.5 volt DC or higher while
the operator is running (battery under load).
2. Program Switch Settings: At the upper center of the board there are 10 program
switches. These switches enable and disable certain features of the Apollo system. DEFAULT setting of these switches is as follows: SINGLE GATE – 1,2,3,5
ON (all others OFF) DUAL GATE – 1,2,5 ON (all others OFF)
3. LED ENABLE BUTTON: On the right side of the board – half way down is the LED
ENABLE button. Pressing this button once and releasing it “enables” the LEDs on
the board for approximately 15 minutes. When the LEDs are enabled – the “STOP”
light should always be lit on the left side of the board. Other LEDs may be lit as
well depending on the status of the operator. If the gate(s) are in the OPEN position, the OPEN limit indicator(s) should be lit. If the gate(s) are CLOSED, the
CLOSED limit indicator(s) should be lit. (The OPEN and CLOSED LEDs should
never be on at the same time) Any LEDs that are lit on the left side of the board or
at the lower right corner of the board (except the STOP LED) indicate a TRIGGER
from an accessory device connected at that location. Devices connected where an
LED is lit should be removed before further testing is done. After the system is
made operational – these devices may be reconnected one at a time. Check for
proper system operation after each connection.
4. Current Sensitivity: At the top center of the board is the “Current Sensitivity” adjustment. It adjusts the amount of force the operator will exert before it senses an obstruction. As the wheel is turned counter clockwise, the operator will reverse more
easily. As the wheel is turned clockwise, the operator will push harder. Any time
the system “CURRENT SENSES” it will stop and reverse for two (2) seconds. If
the system “CURRENT SENSES” a second time before fully opening or closing –
it will again reverse for two (2)_seconds and then go into a HARD SHUTDOWN
(see below). Sensitivity should be set to a level that is sufficiently strong to open
and close the gate in all conditions – yet still sensitive enough to be safe. A good
starting point is the one o’clock position.
TROUBLESHOOTING
25
5. Activating the system: A momentary connection between activation inputs and ground
(GND) is how the system is activated. At the upper left and bottom right of the board
are terminals marked INP or INPUT. These terminals - when momentarily shorted to
ground (GND) - will open, stop and close the gate with each activation. The button on
the side of the box (swing gates ONLY) is connected to these terminals and may be
used to activate the gate when the key is in the horizontal position. On our newest
boards there is an “OPERATE” button at the upper left area of the board that may be
used in the same manner.
6. HARD SHUTDOWN: If the system has encountered an obstruction two times before
fully opening or closing – the HARD SHUTDOWN LED (upper right of board) will begin flashing – indicating a Hard Shutdown situation. Check to see that any obstructions are removed from the gates path and then press the “HARD SHUTDOWN RESET” button to restart the system.
7. Left Hand / Right Hand Operation: All APOLLO Slide Gates are shipped from the factory wired to close to the left (when looking out of the property). It is suggested to install and adjust the operator as it comes from the factory – then re-wire the system if
necessary. The easiest way to determine if your system requires re-wiring is to use
the LED Enable button. Once the LEDs are enabled, the OPEN LIMIT light should
come on in the open position and the CLOSED LIMIT light should come on when the
gate is closed. Should these be backwards – make the following changes: From the
MASTER plug – there are five wires going to a terminal strip… Reverse the RED with
the BLACK - and – reverse the ORANGE with the WHITE. To verify that the wiring
has been changed correctly: Manually move the gate to the mid-way position and plug
the main harness into the EMERGENCY BYPASS receptacle – the gate should
OPEN. If it closes – the RED and BLACK motor wires must be reversed. Once it is
verified that the EMERGENCY BYPASS does open the gate – then check the limit
switch wiring. Dis-engage the mechanical release and open the gate fully – verify the
OPEN LIMIT led is on. Close the gate fully– verify the CLOSED LIMIT led. If the limits
are backwards – reverse the ORANGE and WHITE limit wires.
8. Dual Gate Systems: Test dual gate systems individually. Turn program switch #3 ON
(disables SLAVE side of board) and test actuators one at a time using MASTER side
of board only. Confirm proper operation of each actuator. If both test 100% - then test
together by connecting both actuators and turning program switch #3 to the OFF position.
9. EMERGENCY BYPASS: At the bottom left of the board is the EMERGENCY BYPASS
receptacle. Plugging the operator harness into this receptacle will OPEN the gate
ONLY! It is intended to open the gate(s) should other methods fail. Note that if the motor draws more than 15 amps of current the fuse above the receptacle will blow. Also,
the gate operator will not stop by its self at the open position. The plug must be removed to stop the gate. (This is also a handy way to test that the current consumption
of the motor is within the normal limits)
10. FIRMWARE: In the upper right area of the board there is a micro-processor that has a
white label on it. This is the “FIRMWARE” of the system. Currently (May 2005) we are
using firmware version V31.00.02. For troubleshooting versions of the firmware earlier
then V31.00.00 consult your original instructions that were included with your system.
Systems that are out of warranty may be upgraded to newer version firmware for a
nominal fee.
TROUBLESHOOTING
26
LIMITED TWO-YEAR WARRANTY
Apollo Gate Operators are warranted against defects for a period of
24 months from the date of purchase, providing recommended installation
procedures are followed. This warranty is in lieu of all other warranties
expressed or implied (some states do not allow limitations on how long an
implied warranty lasts, so this limitation may not apply to you) and shall be
considered void if damage was due to improper installation or use,
connection to improper power source, or if damage was caused by fire,
flood, or lightning. The manufacturer will not be responsible for any labor
charges incurred in the removal or replacement of defective parts.
In case of failure due to defective material or workmanship during the
warranty period, the defective part will be repaired or replaced at the
manufacturer’s option at no charge if returned freight prepaid. New or factory
rebuilt replacements may be used. Replacement parts are warranted for the
remaining portion of the original warranty period. The manufacturer will pay
standard ground freight on the return of repaired or replaced items in
warranty.
APOLLO Gate Operators, Inc.
Loading...