Epson ET-2750 User Manual

ET-2750

2

Fill ink tanks

Start Here

Read these instructions before using your product.

Note for Spanish speakers/Nota para hispanohablantes: Para

obtener instrucciones de configuración en español, consulte la Guía
de instalación en www.epson.com/support/et2750sp (requiere una

conexión a Internet).

1

Unpack

Note: This product requires careful handling of ink. If ink spills, wipe it

off immediately with a damp towel to avoid permanent stains. If ink gets
on your clothes or belongings, it may not come off.

Warning: Keep the ink bottles out of the reach of children and do not

drink the ink.

1 Open the ink tank cover, then open the cap for the ink tank

you are going to fill.

2 Unpack one of the ink bottles. Hold the ink bottle upright

and slowly turn the bottle cap to remove it.

Note: Do not open the ink bottles until you are ready to fill the ink

tanks. The ink bottles are vacuum packed to maintain reliability.

1 Remove all protective materials from the product.

2 Lift up the scanner unit. Remove all protective materials

from inside the product.

Caution: Do not shake or squeeze the ink bottles. Do not touch

the top of the ink bottle after its cap is removed.

3 Position the top of the ink bottle along the slot in front of

the filling port, then slowly stand the bottle up to insert it.

Note: Refer to the color-coded sticker on the ink tank unit to

identify the color of each tank. Do not force the bottles into
position; they are keyed for each color.

4 Wait for the ink to fill the tank. Do not squeeze the bottle.

Ink flows into the tank and stops automatically when the
ink is filled to the upper line.

Caution: Do not touch the flat white cable or the ink tubes and

their translucent cover.

Note: If ink does not flow from the bottle, lift and reinsert the

bottle.

5 When the ink tank is full, remove the ink bottle and

securely close the ink tank cap. Place the remaining ink
aside; you will need it later.

Note: Replace the bottle cap and tighten it.

6 Repeat the previous steps for the other colors.

7 Close the ink tank cover and then the scanner unit.

8 Connect the power cord to the back of the product and to

an electrical outlet.

12 When the message to start initialization appears on the

LCD screen, press the start button to start charging
the ink. Ink charging takes approximately 10 minutes. A
message appears when ink charging is complete. Press
the OK button to continue.

Note: After some ink is used for charging, the rest is available for
printing.

Caution: Do not turn off the product, raise the scanner unit, or

load paper while the product is charging or you’ll waste ink.

13 To complete filling the ink tanks, repeat steps 1 through 6

using the remaining ink in the bottles.

Note: Replace the bottle cap before disposing of the bottles.

Caution: Do not connect to your computer yet.

9 Raise the control panel, then press the power button to

turn on the product.

Note: If an error message appears, turn off the product and
check that no protective material has been left inside the product.

10 Press or to select your language on the LCD screen,

then press the OK button. Follow steps 11 and 12 to
continue ink charging.

14 Close the ink tank cover and scanner unit.

15 Select Maintenance > Reset Ink Levels, then follow the

on-screen instructions to reset the ink levels.

16 Follow the on-screen instructions to adjust the print

quality. Press the OK button to continue.

Note: You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.

3

Load paper

See the online User’s Guide for information about loading
capacity and available paper types and sizes.

1 Make sure the product is not charging. Then flip the

feeder guard forward, raise the paper support, and tilt it
backwards slightly.

Note: You can change this setting later using the product’s

control panel. For more information, see the online User’s Guide.

11 When the message to see the Start Here sheet appears

on the LCD screen, press the OK button. On the next
screen, press and hold the help button for 3 seconds.

2 Slide the edge guides all the way out.