Epson EMP-5550 User Manual

Important Information About Your projector

Important Safety Information

Warning:

switched on as the bright light can damage your eyes. Never let
children look into the lens when it is on.

Warning:

lamp and filter covers. Dangerous electrical voltages inside
the projector can cause severe injury. Except as specifically
directed in this Owner’s Manual, do not attempt to service
this product yourself. Refer all servicing to qualified service
personnel.

Warning:

and optional parts out of the reach of children. Children
covering their heads with bags may result in death by
suffocation. Be particularly careful around small children.

Caution:

bulb with your bare hands. The invisible residue left by the oil
on your hands may be shorten the bulb life. Use a cloth or
gloves to handle the new bulb.

Never look into the projector lens when the lamp is

Never open any covers on the projector except the

Keep the plastic bags for the projector, accessories

When you replace the lamp, never touch the new

EMP-7550/7500/5550/5500

Q

operation panel

speaker

operation indicator

remote control receiver

Operation Panel

UICK

Button Function

Power Turns the projector on or off.
Source Switches the input source to Computer or

Menu Displays or hides the menu.
Up, down arrows

(Sync+/Sync-)

Left, right
arrows(tracking-/
tracking+)

Enter button Registers a menu selection.
Resize Switches between Resizing screen and

AV/Mute Turns off the screen and sound of the

– Volume + Adjusts the volume.
Help Displays the help menu for various types of

S

TART

speaker

zoom ring

focus ring

front foot

foot adjust lever

Video.

Synchronizes the computer’s graphic signal.
Use these buttons to adjust an overall image
that is fuzzy or streaked, or to select menu
items during menu operations.

Matches the projector’s internal clock to
various computer graphic signals (tracking
adjustment).
Use these buttons to adjust an image with
vertical lines, or to change numeric settings
during menu operations.

Window screen (PC input).

projector temporarily.

problems you may encounter.

EMP-7550/7500/5550/5500

Source

Menu

Effects

3

2

1

AV/Mute

Resize

Custom

Help

Freeze

- Volume +

Power

Remote control

Q

4

5

UICK

Button Function

Menu Displays or hides the menu.
Source Switches the input source to Computer or

Effects buttons Use to display special effects; 1 Pointer, 2

Top multi-purpose
button

Bottom multi­purpose button

Help Displays the help menu for various types of

Resize Switches between Resizing screen and

Custom Zooms an image using the Mouse Right/Left

Freeze Keeps the current computer or video image

AV/Mute Turns off the screen and sound of the

– Volume + Adjusts the volume.
Power Turns the projector on or off.

S

TART

Video.

Box, 3 Line, 4 Marker, 5 Clear.
Acts as a right mouse click, registers a menu

selection, and selects other custom
functions.

Acts as a left mouse click, registers a menu
selection, and selects other custom
functions.

problems you may encounter.

Window screen (PC input).

buttons.

on the screen.

projector temporarily.

Connecting to
a PC laptop computer

Computer cable

Connecting to
a Macintosh PowerBook

Mac
desktop
adapter

Computer cable

Video
cable
adapter

After sales service contact addresses

EPSON (UK) LIMITED
[phone]
Campus 100
Maylands Avenue
Hemel Hempstead
Herts. HP2 7TJ
United Kingdom

EPSON FRANCE S.A.
33-1-40873737
68 Bis Rue Marjolin
92305 Levallois Perret
France

EPSON DEUTSCHLAND GMBH
0211/56030
Zülpicher Straße 6,
40549 Düsseldorf
F.R. Germany

EPSON ITALIA S.P.A
0039-2-26233-1
V.le Casiraghi 427
20099 Sesto S. Giovanni (MI)
Italy

EPSON HONG KONG LIMITED
(852) 2585 4300
Rooms 4706-10 47 th Floor
China Resources Building
26 Harbour Road Wanchai
Hong Kong

EPSON ELECTRONICS TRADING
LTD. (TAIWAN BRANCH)
[phone]
10F, No. 287 Nanking E.Road, Sec.3,
Taipei, Taiwan R.O.C.

EPSON SINGAPORE PTE LTD
337-7911
No.1, Temasek Avenue
#36-00, Millenia Tower
Singapore 039192
Singapore

EPSON AUSTRALIA PTY
LIMITED
[phone]
70 Gibbes Street
Chatswood NSW 2067
Australia

EPSON IBÉRICA, S.A.
(93) 5821500
Av. Roma, 18-26
08290 Cerdanyola del Vallès
(Barcelona)
Spain

®

DATA/VIDEO PROJECTOR

Owner’s Manual

All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written
permission of SEIKO EPSON CORPORATION. No patent liability is
assumed with respect to the use of the information contained herein. Neither
is any liability assumed for damages resulting from the use of the information
contained herein.

Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to
the purchaser of this product or third parties for damages, losses, costs, or
expenses incurred by purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations
to this product, or (excluding the U.S.) failure to strictly comply with SEIKO
EPSON CORPORATION’s operating and maintenance instructions.

SEIKO EPSON CORPORATION shall not be liable against any damages or
problems arising from the use of any options or any consumable products
other than those designated as Original EPSON Products or EPSON
Approved Products by SEIKO EPSON CORPORATION.

EPSON is a registered trademark and PowerLite is a trademark of SEIKO
EPSON CORPORATION.

General Notice: The following trademarks and registered trademarks are the

property of their respective owners and are used in this publication for
identification purposes only.

• EPSON/Seiko Epson Corp.

• Macintosh, Macintosh OS System 7, PowerBook, Quadra, Centris, Power
Mac/Apple Computer Corp.

• IBM/International Business Machines, Inc.

• Windows 3.x, Windows 95/Microsoft Corp.

• SRS and the SRS symbol are registered trademarks of SRS
Labs, Inc. in the United States and selected foreign countries.
SRS technology is incorporated under license from SRS Labs, Inc. and is
protected under United States Patent Nos. 4,748,669 and 4,841, 572
with numerous additional issued and pending foreign patents.
Purchase of this product does not convey the right to sell recordings made
with SRS technology.

• SRS is an abbreviation for SOUND RETRIEVAL SYSTEM.

Other product names used herein are also for identification purposes only and
may be trademarks of their respective owners. EPSON disclaims any and all
rights in those marks.

■

■

■

■

■

■

■

■

■

■

■

■

■

■

Contents

Contents iii
Introduction vii

Getting the Most Out of Your Projector................................ix

Remote control ..........................................................................ix

Optional Accessories....................................................................x

About This Manual................................................................xi

Safety Instructions................................................................xii

Where to Get Help..............................................................xiv

World Wide Web site.................................................................xv

Transporting your projecotor................................................ xv

■

■

1 Installation 1

Unpacking the Projector.........................................................2

Additional Components.............................................................. 3

Setting Up the Projector.........................................................4

Connecting to a Computer.....................................................7

Connecting to a PC desktop computer ....................................... 8

Connecting to a PC laptop computer........................................ 10

Connecting to a Macintosh desktop computer..........................12

Connecting to a Macintosh PowerBook.................................... 14

Connecting to a Video Source..................................................16

Connecting to an External Speaker or PA System..................18

■ ■ ■ ■ ■

iii

2 Using the Projector 21

Turning the Equipment On and Off.....................................23

Turning the Projector On and Off............................................23

Sleep Mode.............................................................................. 24

Focusing and Positioning the Screen Image ..........................25

Resize Button........................................................................... 27

Controlling the Projector.......................................................... 28

Using the Remote Control....................................................... 29

Using the Operation Panel ....................................................... 31

Projector Status Indicators....................................................33

Operation Indicator.................................................................. 33

Lamp Indicator......................................................................... 34

Temperature Indicator.............................................................. 34

3 Using the Projector Menus 35

Accessing the Main Menu.....................................................36

Changing a Menu Setting.....................................................36

Video Menu (Image source = Computer) ................................. 39

Video Menu (Image source = Video)........................................ 41

Audio Menu............................................................................. 42

Setting Menu ........................................................................... 42

User’s Logo Menu ................................................................... 45

Effect Menu ............................................................................. 47

About Menu............................................................................. 48

RESET ALL Menu................................................................... 48

■ ■ ■ ■

4 Maintenance 51

Cleaning the Lens.................................................................52

Cleaning the Projector Case..................................................52

Cleaning the Air Filter..........................................................53

Replacing the Lamp..............................................................54

5 Troubleshooting 57

Problems with the Projector..................................................58

Problems with the Image or Sound.......................................60

Contents

iv

■

6 Technical Specifications 63

Supported Monitor Displays (EMP-7550/7500)..................65

Supported Monitor Displays (EMP-5550/5500)..................66

Monitor and Computer connector pin assignments...............67

Glossary 69

■ ■ ■ ■ ■

v

■ ■ ■ ■

vi

Contents

■

■

■

■

■

■

■

Introduction

Y

our EPSON EMP series projector is a compact, lightweight
projector that lets you project XGA(EMP-7550/7500) or
SVGA(EMP-5550/5500) full-color images and video onto a
large screen for presentations. The projector can connect
simultaneously to two image sources: one PC or Apple®
Macintosh® computer image sources plus one video source
such as a video tape deck, camcorder, or digital camera. Audio
can also be connected for each image source.

■

■

■

■

■

■

■

■

■

Images are displayed in true XGA and SVGA full color
(16,670,000 colors) at a resolution of 1024 × 768(EMP­7550/7500) and 800 × 600(EMP-5550/5500) pixels. Your
projector produces bright images that can be easily seen in
rooms light enough to take notes. Audio can be produced
from the projector’s 1W+1W stereo, which employ a built-in
SRS 3D sound® for output that is rich and powerful. You can
also connect an external speaker when further amplification is
required.

A totally new AVTSS™ (Automatic Video Tracking and
Synchronization Sensing, patent pending) provides automatic
set-up of image from a computer for quick and easy
projection of beautiful images every time.

You can control your projector through a hand-held remote
control unit, with menus being provided for image source
switching and image adjustment. The remote control can also
act as a wireless mouse to control mouse operations on your

■ ■ ■ ■ ■

vii

computer screen during presentations. The optional ELP
LINK III™ provides a number of add-on features that are
designed to make presentations more effective.

Your projector also features a new patented BIS CUIT
(Balanced Image Size Conversion UnIT) chip which supports
XGA(EMP-7550/7500), VGA~XGA(EMP-5550/5500)
computer output, as well as VGA and SXGA output. No
matter what type of computer output is used, the result is a
full-size video image of outstanding clarity.

Your projector supports IBM-compatible PCs and laptops, as
well as Apple® Macintosh®, Power Macintosh and
PowerBook computers. The video source can be NTSC, PAL
or SECAM in composite video, S-Video format.

■ ■ ■ ■

viii

Introduction

■

Getting the Most Out of Your Projector

Your projector comes with a full set of features that enable
you to control the settings for the image display, video and
audio. To get the most out of your projector, read this section
for a quick summary of the important features.

Remote control

The buttons on the remote control let you turn the projector
on or off, and provide direct access to auto set-up, blank,
freeze, volume, mute and image source switching. Use the
remote control buttons to access custom functions and the
projector's menu system. You can even use the remote control
in place of your computer's mouse.

Getting the Most Out of Your Projector

■ ■ ■ ■ ■

ix

Optional Accessories

To enhance your use of the projector, EPSON provides the
following optional accessories:

• Spare lamp (EMP-7500/5500) ELPLP06

• Spare lamp (EMP-7550/5550) ELPLP07

• Computer cable ELPKC02

• Link set for PC ELPSW03

• Link set for Mac ELPSW04

• Link ser for 98 ELPSW05

• Image Presentation Camera ELPDC01

• Mac Adapter Set ELPAP01

• Ceiling Mount ELPMB03

■ ■ ■ ■

Introduction

x

• Ceiling Plate ELPFC01

• Pipe 370 ELPFP01

• Pipe 570 ELPFP02

• Pipe 770 ELPEP03

• Hard Travel Case ELPKS11

• Portable Screen ELPSC06

• PC Selector ELPST01

■

About This Manual

Chapter 1, “Installation”, gives step-by-step instructions on
how to set up the projector and connect it to your computer,
video source, or other external speaker or PA system. Read
the installation procedures that apply to your configuration.

Chapter 2, “Using the Projector”, describes how to switch
the projector on/off and control simple projector settings
using the remote control or operation panel.

Chapter 3, “Using the Projector Menus”, describes how to
use the menus to adjust the color and image settings, change
the display of the projected image and modify audio settings
such as bass and treble.

Chapter 4, “Maintenance”, describes how to clean your
projector and perform limited maintenance.

Chapter 5, “Troubleshooting”, describes you how to
interpret the projector’s indicator lights and gives helpful
information for avoiding errors, optimizing image quality and
solving problems.

Chapter 6, “Technical Specifications,” lists the technical
specifications for your projector.

A Glossary and Index are provided at the end of the manual.

About This Manual

■ ■ ■ ■ ■

xi

Safety Instructions

Follow these safety instructions when setting up and using the
projector:

1. Do not place the projector on an unstable cart, stand, or

table.

2. Do not use the projector near water or sources of heat.

3. Use attachments only as recommended.

4. Use the type of power source indicated on the projector.

If you are not sure of the power available, consult your
dealer or local electricity company.

5. Place the projector near a wall outlet where the plug can

be easily unplugged.

6. Insert the projector’s three-pin grounding-type plug into

a properly grounded outlet. If you have a two-prong
outlet, contact an electrician to replace it. Do not handle
the plug with wet hands.

7. Take the following precautions when handling the plug.

Failure to comply with these precautions may result in
sparks or fire.

■ ■ ■ ■

xii

• Do not insert the plug into an outlet with dust present.

• Insert the plug firmly into the outlet.

8. Do not overload wall outlets, extension cords or integral

convenience receptacles. This may cause fire or electric
shock.

9. Do not place the projector where the cord can be stepped

on. It may result in fraying or damage to the plug.

10.Unplug the projector from the wall outlet before cleaning.

Use a damp cloth for cleaning. Do not use liquid or
aerosol cleaners.

Introduction

■

11.Do not block the slots and openings in the projector case.

They provide ventilation and prevent the projector from
overheating. Do not place the projector on a sofa, rug or
other soft surface, or in a closed-in cabinet unless proper
ventilation is provided.

12.Never push objects of any kind through cabinet slots.

Never spill liquid of any kind into the projector.

13.Except as specifically explained in this User’s Guide, do

not attempt to service this product yourself. Refer all
servicing to qualified service personnel. Opening or
removing covers may expose you to dangerous voltages
and other hazards.

14.Unplug the projector during thunder storms or when it

will not be used for extended periods.

15.Do not place the projector and remote control on top of

heat-producing equipment or in a heated place, such as a
car.

16.Unplug the projector from the wall outlet and refer

servicing to qualified service personnel under the
following conditions;

• When the power cord or plug is damaged or frayed

• If liquid has been spilled into the projector or it has
been exposed to rain or water

• If it does not operate normally when you follow the
operating instructions, or if it exhibits a distinct change
in performance, indicating a need for servicing.

• If it has been dropped or the housing has been
damaged.

Safety Instructions

■ ■ ■ ■ ■

xiii

Where to Get Help

If you are haveing trouble setting up or running your
projector, first see Chapter 5, "Troubleshooting". If you
cannot resolve the problem, contact the appropriate
representative listed in the section entitled "After sales service
contact addresses" at the end of this manual.

Before you call, please have the following information ready:

• Product name

• Product serial number

• Computer configuration

• Description of the problem

■ ■ ■ ■

xiv

Introduction

■

World Wide Web site

If you connect to the Internet and have a Web browser, you
can access to EPSON’s World Wide Web site at http:// www.
epson. com. EPSON’s home page provides you What’s New,
EPSON Products, EPSON Connection, Corporate Info and
EPSON Contacts. Link to the EPSON Connection for the
latest drivers and FAQ’s (Frequently Asked Questions) and
the EPSON Chart area. To get in touch with EPSON around
the world, EPSON Contacts includes Contact Information
for local EPSON subsidiaries.

Transporting your projecotor

Your projector contains many glass parts and precision parts.
To prevent shock damages while transporting, handle as the

following.
When transporting to maker due to troubleshooting

• Use the original packing.

• If you don’t have the original packaging use the equivalent.
Put cushioning around the projector.

When frequently transporting for business use

• First, put the projector in a hard travel case(optional
accessories : ELPKS11), then pack it in a firm box, using
cushioning. Be sure to ask the delivery company which
treats a precision device.

Transporting your projecotor

■ ■ ■ ■ ■

xv

When carrying by hands

• Use a hard travel case (optional accessories : ELPKS11) or a
soft travel case (additional components).

When traveling by an airplane

• Be sure to bring the projector with you when traveling by
an airplane.

• When transporting the projector as baggage on an airplane,
first put the projector in a hard travel case to avoid any
damage.

EPSON shall not be liable against any damages arose during
the transportation.

■ ■ ■ ■

xvi

Introduction

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

■

1

Installation

This chapter describes how to unpack and set up your

projector, and connect it to other equipment. The projector
must be connected to a computer or a video source such as a
video tape deck, camcorder, digital camera or laser disk player
before it can project any images.
You may also what to set up the projector for one or more of
the following:

• Connect the mouse cable to use the remote control as a
wireless mouse.

• Connect the projector to an audio source for one or both
image sources. The audio source can be the computer,
video source, or another device such as a stereo.

• Connect the projector to an external speaker or PA system
to amplify the audio.

■ ■ ■ ■ ■

1

Unpacking the Projector

When you unpack the projector, make sure you have all these
components:

• Projector

• Remote Control

• 2 AA batteries

• Power cord

• Computer cable

• Audio cable

• A/V cable

• Mouse cable (for PS/2 and Mac)

• Owner’s manual

• Hand strap

• Soft carrying case

Depending on the configration of your equipment, you may
not need all these components.

■ ■ ■ ■

Save all packing in case you need to ship the projector in the
future. It should always be transported in its original packages
or the equivalent.

2

■

Additional Components

Depending on how you plan to use the projector, you may
need these additional components:

• To receive an S-Video signal, you need an S-Video cable.
(One is usually provided with your video device.) A
separate cable is required for each video source.

• To connect the projector to a Macintosh PowerBook, you
need a video-out cable.
(One is provided by/or can be purchased from Apple for all
new PowerBooks that have video-out capability.) If your
PowerBook does not include one, see your Macintosh
dealer.

• To connect the mouse cable to your computer, you may
require a special connector, cable, or other components.
You can obtain these items from your computer dealer. If
your computer doesn't have a mouse connector, you
cannot use the mouse cable.

♦

Note:

You can connect a Kensington MicroSaver® anti-theft
device in the hole on the projector's right side. Contact your
computer dealer.

Unpacking the Projector

■ ■ ■ ■ ■

3

Setting Up the Projector

1. Place the projector on a sturdy, level surface within five

feet of the computer or video source.

♦

Caution:

Do not hold the projector by the lens. This can damage

the lens.

2. Place the projector at a correct distance from the screen.

The distance between the projector and the screen
determines the actual image size. Use the general
guidelines below to determine the correct distance.

Screen size Horizontal distance from projector to screen

300 inches (610x460cm)493.7 inches (12.6 m) ~ 638.7 inches (16.3 m)
200 inches (410x300cm)315.0 inches (8.0 m) ~ 409.4 inches (10.4 m)
100 inches (200x150cm)157.5 inches (4.0 m) ~ 204.7 inches (5.2 m)
80 inches (160x120cm)126.0 inches (3.2 m) ~ 165.4 inches (4.2 m)
60 inches (120x90cm) 94.5 inches (2.4 m) ~ 122.0 inches (3.1 m)
40 inches (81x61cm) 63.0 inches (1.6 m) ~ 82.7 inches (2.1 m)
30 inches (61x46cm) 47.2 inches (1.2 m) ~ 63.0 inches (1.6 m)
25 inches (51x38cm) 39.4 inches (1.0 m) ~ 51.2 inches (1.3 m)
19 inches (39x29cm) 39.4 inches (1.0 m)

■ ■ ■ ■

4

■

3. Turn the projector so that the lens is at right angles to the

screen. If the projector is not angled correctly, the screen
image will be crooked.

4. Connect one end of the power cable to the projector’s

power connector. Connect the other end to an earthed
electrical socket.
The projector should be in sleep mode, indicated by an
orange power indicator.

♦

Warning:

Never look into the lens when the projector is on.
There is a risk that the projector might come on suddenly even
though it is not in use. The light from the lamp can damage your
eyes. It is especially important that children should not be
allowed to look into the lens.

Setting Up the Projector

■ ■ ■ ■ ■

5

5. To insert the batteries in the remote control device, slide

off the battery compartment cover as shown below.

6. Insert the two AA batteries included with the projector.

Make sure the polarity of the batteries is correct.

7. Replace the battery compartment cover.

■ ■ ■ ■

When replacing batteries, take the following precautions:

• Do not recharge the used batteries or expose to fire or

water.

• Replace batteries as soon as they run out. If the batteries

leak, wipe away battery fluid with a soft cloth. If fluid gets
on your hands, wash them immediately.

• Remove the batteries if you will not be using the projector

for a long period of time.

6

■

Connecting to a Computer

You can connect the projector to a computer capable of XGA,
VGA, and SVGA output. Resizing is supported for VGA,
XGA output. The following types of computers are
supported:

• IBM desktop PC or compatible

• IBM laptop or compatible

• Apple Macintosh desktop computer, including Macintosh

Quadra®, Macintosh Centris®, and Power Macintosh

• Any Apple PowerBook with video-out capability, including

all 160, 165, 180 and 500 series PowerBooks

To connect the video and mouse cable ( to use the wireless
remote as a mouse pointer), see the section in this chapter
that applies to your computer.

Connecting to a Computer

■ ■ ■ ■ ■

7

Connecting to a PC desktop computer

Before beginning, turn off the projector and computer if they
are on.

1. Connect the computer cable.

Monitor cable

Computer cable

■ ■ ■ ■

♦

Note:

Computer configurations vary. See your computer
manual for the location of the ports needed to connect your
projector.

a. Connect either end of the computer cable to the

projector’s Computer In port.

b. Disconnect the monitor cable from the computer, and

connect the other end of the computer cable to the
terminal where the monitor cable is disconnected from
the computer.

c. If necessary, connect the monitor cable of the

computer monitor to the projector’s Computer Out
port.

d. Tighten the screws on all connectors.

8

■

2. Connect the audio cable if needed.

Audio cable

a. Connect one end of the audio cable to the Audio In

jack on the projector.

b. Connect the other end of the audio cable to the audio

out port on a sound card in the computer.

Connecting to a Computer

■ ■ ■ ■ ■

9

Connecting to a PC laptop computer

Before beginning, turn off the projector and computer if they
are on.

1. Connect the computer cable.

Computer cable

■ ■ ■ ■

10

♦

Note:

Laptop configurations vary. See your computer manual
for the location of the ports needed to connect your projector.

a. Connect either end of the computer cable to the

projector’s Computer In port.

b. Connect the other end of the computer cable to the

laptop’s video (monitor) port.

c. Tighten the screws on all connectors to make sure they

are fastened securely.

■

2. Connect the audio cable.

Audio cable

a. Connect one end of the audio cable to the Audio In

jack on the projector.

b. Connect the other end of the audio cable to your

laptop.

Connecting to a Computer

■ ■ ■ ■ ■

11

Connecting to a Macintosh desktop computer

Before beginning, turn off the projector and computer if they
are on.

1. Connect the computer cables.

*Video

cable
adapter

Mac monitor

* Mac

desktop
adapter

Monitor cable

Computer cable

adapter

■ ■ ■ ■

12

♦

Note:

Macintosh computer configurations vary. See your
computer manual for the location of the ports needed to connect
your projector.

* You may need adapters that came with your computer or

purchased from your computer dealer for connecting.

a. Connect either end of the computer cable to the

projector’s Computer In port.

b. Connect the other end of the computer cable to the

monitor or video port where monitor cable is
disconnected from the computer.

c. If necessary, connect the monitor cable to the

projector’s Computer out.

■

2. Connect the audio cable.

Audio cable

a. Connect one end of the audio cable to the Audio In

jack on the projector.

b. Connect the other end of the audio cable to your

computer.

Connecting to a Computer

■ ■ ■ ■ ■

13

Connecting to a Macintosh PowerBook

Remember that you can only use a PowerBook model that has
video-out capability. See page 7 for more information.

Before beginning, turn off the projector and computer if they
are on.

1. Connect the computer cable.

*Mac desktop

adapter

Computer cable

Video
cable
adapter

■ ■ ■ ■

14

♦

Note:

PowerBook configurations vary. See your computer
manual for the location of the ports needed to connect your
projector.

* You may need adapters that came with your computer or

purchased from your computer dealer for connecting.

a. Connect the other end of the computer cable to the

projector’s Computer In port.

b. Connect the other end of the computer cable to the

video port (monitor output port) of your PowerBook.

c. Tighten the fixed screws on all connectors.

■

2. Connect the audio cable.

Audio cable

a. Connect one end of the audio cable to the Audio In

jack on the projector.

b. Connect the other end of the audio cable to your

computer.

Connecting to a Computer

■ ■ ■ ■ ■

15

Connecting to a Video Source

You can connect a video tape deck, camcorder, laser disc
player or any other compatible video image source to your
projector.
The projector can receive composite video or S-Video. If your
video source has a one-pin RCA video jack, your equipment
has composite video. If your video source has a four-pin video
jack, your equipment has S-Video. If your video source has a
three-pin video jack, your equipment has G Sync-Video.

♦

Note:

The projector is not compatible with a cable TV-style F
connector.

You can connect the projector to both an S-Video and a
composite video source at the same time. However, the
projector automatically selects the S-Video as the video
source. To display composite video, first disconnect the
S-Video source.

The projector supports NTSC, PAL, PAL 60 and SECAM
video formats, and automatically detects and identifies the
video format. However, you can specify that a single
broadcast format being detected. (See “Video menu” in
Chapter 3.)
Note that the projector will then be able to detect only one
type of video format.

The type of cable you use to connect the video source to
the projector depends on whether you have composite
video, S-Video or G Sync-Video. For composite video, use
the audio/video (A/V) cable supplied with the projector.
For S-Video, use the S-Video cable and the audio cable
supplied with your video device or obtain one from your
computer dealer. For G Sync-Video, use the BNC type
cable came with your video source.

■ ■ ■ ■

16

■

To connect a video source to the projector:

1. Turn off the projector and video source if they are on.

2. If your composite video uses an RCA-type composite

video connector, you will need the A/V cable supplied
with your projector. If your video uses a S-Video, you will
need to provide YOUR OWN S-Video or use the S-Video
cable that came with your video source.

3. For composite video, connect the yellow RCA plug at one

end of the A/V cable to the projector’s Video jack.
Connect the other yellow RCA plug to the video-out jack
on the video source.

A/V cable

4. Connect the other plugs on the A/V cable to the Audio

jacks of the projector: insert the white plug into the L jack
and the red plug into the R jack. Connect the plug at the
other end of the A/V cable to the audio output jacks of
the video source.

Connecting to a Computer

■ ■ ■ ■ ■

17

5. For S-Video, insert one end of the S-Video cable into

the projector’s S-Video jack. Insert the other end in the
S-Video Out jack on your S-Video source.

S-Video cable

Connecting to an External Speaker or PA System

Although the projector's internal speakers are enough for
most small-size or medium-size rooms, an external speaker for
large room to gain maximum benefit from the projector's
built-in SRS 3D sound function.

■ ■ ■ ■

To connect the projector to an external sound system, you
need to obtain an RCA-to-3.5 mm stereo mini audio cable or

3.5 mm stereo mini audio cable from your computer dealer.

1. Before beginning, turn off the projector and all sources if

they are on.

18

■

2. Connect the cable's 3.5 mm stereo mini plug to the

projector's Audio Out jack.

RCA/3.5 mm cable

3. Connect the other end of the cable to the external speaker

or PA system. Insert the cable's red RCA plug into the
right channnel, and the white RCA plug into the left
channel.

Connecting to an External Speaker or PA System

■ ■ ■ ■ ■

19

■ ■ ■ ■

20

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

■

2

Using the Projector

This chapter provides the following information about using

your projector:

• Turning the equipment on and off

• Focusing and positioning the screen image

• Controlling the projector with the remote control and the

operation panel

• Monitoring the projector's operating status

■ ■ ■ ■ ■

21

The illustration below identifies the parts of your projector.

operation panel

speaker

zoom ring

focus ring

speaker

operation indicator

remote control receiver

front foot

foot adjust lever

■ ■ ■ ■

22

■

Turning the Equipment On and Off

Turn on the projector and its attached equipment in the
following order.

1. Video source

2. Audio source (if different from computer or video source)

3. Projector

4. External speaker or PA system

5. Computer
When you turn off the equipment, do so in the reverse order.

Turning the Projector On and Off

1. Remove the projector lens cap.

2. Press the Power button on the remote control or

operation panel. The power indicator flashes as the
projector warms up. When the projector is fully warmed
up, this light remains green.

If computer or video equipment is attached, the computer or
video signal is projected.

♦

♦

Allow about 30 seconds for full illumination.

Warning:

Never look into the lens when the lamp is on. This can
damage your eyes. It is especially important that children are not
allowed to look into the lens.

Caution:

When turning the projector on or off with the remote
control, be sure to turn the remote control on first with the power
switch.

Turning the Equipment On and Off

■ ■ ■ ■ ■

23

After you press the Power button to turn off the projector,
the fan will remain on and the operation indicator will flash
orange for about one minute as the projector cools down.

operation indicator

When the projector has cooled down, the operation indicator
stops flashing and remains orange.

♦

Note:

while the operation indicator is orange, there may be a delay
before a projected image appears.

♦

Note:

Doing so may print the image and cause the afterimage on the
panel.

Sleep Mode

Sleep mode conserves electricity by automatically turning off
the lamp after the projector has not been used for 30 minutes.
In sleep mode, the projector’s operation indicator is orange
and only a minimum amount of the projector’s circuitry
remains on. This conserves electricity, cools the projector, and
extends the life of the lamp. When the projector is in sleep
mode, you can press the Power button to resume projecting
images, or you can unplug the projector’s power cord to turn
it off.

♦

Note:

switch on the projector. The orange operation indicator turns off.

If you press the Power button to turn the projector back on

Do not project the same static image for extended time.

When you don’t use the projector, turn off the power

■ ■ ■ ■

24

■

Focusing and Positioning the Screen Image

When an image appears on the screen, check that if it is in
focus and correctly positioned on the screen.

zoom ring

focus ring

• To focus the image, rotate the focus ring (the outer ring on

the projector’s lens).

• To adjust the size of the image, rotate the inner zoom ring.

Rotate the zoom ring wide to make the image larger, or
tele to make it smaller.

Focusing and Positioning the Screen Image

■ ■ ■ ■ ■

25

If you need to raise or lower the image on the screen, extend
or retract the two feet at the bottom of the projector as
follows:

1. Stand behind the projector and support the front of it

while you lift the foot adjust lever above the feet. This
unlocks the feet so they can move up and down freely. Do
not let the projector drop.

■ ■ ■ ■

26

♦

Caution:

Do not hold the projector by its lens. This can damage

the lens.

2. While lifting the foot adjust lever, raise or lower the

projector until the screen image is positioned correctly.

3. Release the lever to lock the feet in their new position.

4. To fine-tune the height of the projector, turn the rear feet

clockwise to raise the height or anti-clockwise to lower it.

■

Resize Button

The Resize button lets you switch between Resize display and
Window display.

The Resize button cannot be used with XGA(1024 × 768
pixels) for EMP-7550/7500 and SVGA(800 × 600 pixels) for
EMP-5550/5500.

How to switch

With images up to XGA(1024 × 768 pixels) size (for example
a 600 × 480 pixels VGA image), press the Resize button
alternately. The Resize display changes the VGA(600 × 480)
image into the SVGA(800 × 600) image. The Window display
projects the VGA(600 × 480) image as it is. The projected
image gets smaller than SVGA(800 × 600) image.

With images SVGA(800 × 600 pixels) size, the image is
displayed with the maximum size in both Resize and Window
display. Pressing the Resize button does not make any
change.

With images larger than SVGA(800 × 600 pixels) size (for
example a 1024 × 768 pixels XGA image), you can either
select to display a portion of the projected image (Window
display) or the entire projected image (Resize display).

Each time you press the Resize button, the projected image is
displayed in the following order:

1. The XGA image is reduced to the SVGA size.

2. The projected image is displayed with XGA size, and only

the upper of the right image is projected on the screen.

3. The upper of the left image is projected on the screen.

4. The bottom of the right image is projected on the screen.

5. The bottom of the left image is projected on the screen.

6. The center of the image is projected on the screen.
After the step 6, press the Resize button again to return to the

step 1.

Focusing and Positioning the Screen Image

■ ■ ■ ■ ■

27

Controlling the Projector

You can use the operation panel on top of the projector or the
remote control to perform the following actions:

• Turn power on and off

• Switch between input sources (video - computer)

• Access the projector menus to adjust the image, audio,

video, and display settings

• Control resizing

• Control display freeze

• Control A/V mute (Cuts off the image and sound

temporarily.)

• Adjust or mute audio output

• Use custom functions (remote control only)

• Use effect functions (for enhancing projected images on the

screen; remote control only)

■ ■ ■ ■

28

■

Using the Remote Control

Source

Menu

♦

pointer button

Effects

3

4

2

1

5

bottom

top
multi-purpose
button

Resize

Freeze

AV/Mute

Custom

Help

- Volume +

Power

multi-purpose
button

Remote control

To use the remote control, point it towards the remote
control receivers located at the front and back of the
projector.

To be able to use the remote control as a cordless mouse,
connect the mouse cable (for PS/2) to the projector and your
computer.

You can use the remote control up to 10 metres (33 feet)
from the projector.

Note:

The projector may not respond to remote control
commands in these conditions: ambient light is too bright; a
certain type of fluorescent light is present; a strong light source
(such as direct sunlight) shines into the infrared receiver; or
other equipment emitting infrared energy is present (such as a
radiant room heater). Correct these conditions to use the remote
control or control the projector from a computer.

♦

Note:

If you use the other mouse except the PS/2 mouse, you need

to purchase the Link Set to connect.

Focusing and Positioning the Screen Image

■ ■ ■ ■ ■

29

In addition to the remote control, you can also control the
projector by using the buttons on the projector’s operation
panel located on top of the projector.

This table summarizes the functions on the remote control.

Button Function

Menu Displays or hides the menu.
Source Switches the input source to Conmputer or Video.
Effects buttons Use to display special effects; 1 Pointer, 2 Box, 3 Line,

4 Marker, 5 Clear.

Top multi­purpose button

Bottom multi­purpose button

Help Displays the help menu for various types of problems

Resize Switches between Resizing screen and Window

Custom Zooms an image using the Mouse Right/Left buttons.
Freeze Keeps the current computer or video image on the

AV/Mute Turns off the image and sound of the projector

– Volume + Adjusts the volume.
Power Turns the projector on or off.

Acts as a right mouse click, registers a menu
selection, and selects other custom functions.

Acts as a left mouse click, registers a menu selection,
and selects other custom functions.

you may encounter.

screen (PC input).

screen.

temporarily.

■ ■ ■ ■

30

■

Using the Operation Panel

Operation Panel

You can use the operation panel to control the projector
instead of the remote control. However, you can program and
access the custom features only using the remote control.

Enter button

Focusing and Positioning the Screen Image

■ ■ ■ ■ ■

31

The following table summarizes the functions on the
operation panel.

Button Function

Power Turns the projector on or off.
Source Switches the input source to Conmputer or Video.
Menu Displays or hides the menu.
Up, down arrows

(Sync+/Sync-)

Left, right
arrows(tracking-/
tracking+)

Enter key Registers a menu selection.
Resize Switches between Resizing screen and Window

AV/Mute Turns off the screen and sound of the projector

– Volume + Adjusts the volume.
Help Displays the help menu for various types of problems

Synchronizes the computer’s graphic signal.
Use these buttons to adjust an overall image that is
fuzzy or streaked, or to select menu items during
menu operations.

Matches the projector’s internal clock to various
computer graphic signals (tracking adjustment).
Use these buttons to adjust an image with vertical
lines, or to change numeric settings during menu
operations.

screen (PC input).

temporarily.

you may encounter.

■ ■ ■ ■

32

■

Projector Status Indicators

The power and lamp indicators at the top of the projector tell
you its operating status.

Operation Indicator
Lamp Indicator
Temperature Indicator

♦

Caution:

A red indicator warns you if a serious problem occurs.
See Chapter 5, “Troubleshooting,” for what to do if a warning
light comes on.

Operation Indicator

Displays machine condition.

Color Status Meaning

Orange Lit Sleep mode.
Green Flashing The projector is warming up. Allow about

Green Lit

Orange Flashing Projection lamp is off, and the projector is

Red Flashing There is an internal projector problem, or

(every 1 sec)
Lit

(every 2 sec)

30 seconds.
Power and the projection lamp are on.

The computer is in the suspended mode.
When the suspended mode is released,
the projector starts projecting.

cooling down for 2 minute. During the
cooling, any operations can not be
executed.

the power to the projector has been cut off.

Projector Status Indicators

■ ■ ■ ■ ■

33

Lamp Indicator

Displays lamp condition.
This indicator is off when the projector is in a normal

condition.

Color Status Meaning

- Off Lamp is functioning normally.
Orange Flashing The lamp needs to be replaced.
Red Lit Projection lamp has reached the end of its

life and will not longer project images.
Replace the projection lamp with a new
one.

Red Flashing There is a problem with the projection

lamp, lamp power supply, lamp fuse, or a
circuit malfunctioned in the projector.

Temperature Indicator

Displays the internal temperature condition.
This indicator is off when the projector is in a normal

condition.

■ ■ ■ ■

Color Status Meaning

- Off The projector is functioning normally.
Orange Flashing The projector is too hot.
Red Lit The projector has turned off automatically

because of overheating.

Red Flashing There is problem with the cooling fan or

temperature sensor. Call service
representative.

34

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

■

3

Using the Projector Menus

The seven projector menus enable you to control your

projector.

• The Computer menu controls the computer image, such as

brightness and contrast, when the image source is
computer.

• The Video menu controls the video image, such as

brightness and color saturation, when the image source is
video, such as a VCR.

• The Audio menu controls audio features, such as the

volume level, tone setting, and sound.

• The Setting menu enables you to set various projector

options.

• The User’s logo menu allows you to select special features

such as zoom, backcolor or logo.

• The Effect menu allows you to use effect buttons.

• The About menu provides information about lamp hours,

frequency and etc..

• The Reset All menu returns all settings to their factory

defaults.

■ ■ ■ ■ ■

35

Accessing the Main Menu

To display the Main menu, press the Menu button on the
operation panel or remote control. The Main menu appears:

Press the Menu button again to hide the menu.

Changing a Menu Setting

To change a menu setting:

1. Press the Menu button on the operation panel or remote

control to display the Main menu.

■ ■ ■ ■

36

■

2. Press the up or down buttons (operation panel) or press

the top or bottom of the pointer button (remote) to scroll
through the menu choices.

Source

Menu

Effects

3

4

2

Resize

Freeze

5

AV/Mute

Custom

Help

- Volume +

Power

up and down
buttons

pointer button

1

Changing a Menu Setting

■ ■ ■ ■ ■

37

3. Press either the Enter button (operation panel) or the top

or bottom multi-purpose button (remote) to display a
submenu.

Source

Menu

Effects

3

4

2

1

5

♦

top

multi-purpose

button

Enter button

bottom

Resize

Freeze

AV/Mute

Custom

Help

- Volume +

Power

multi-purpose

button

As you select a menu, a sub-menu of options appears to the
right.

Note:

The options available in some submenus vary, depending
on whether the current image source is the computer or a video
source.

■ ■ ■ ■

38

■

4. Press the up or down buttons (operation panel) or the top

or bottom of the pointer button (remote) to scroll
through the menu choices.

5. Press either the left or right buttons (operation panel) or

the right or left sides of the pointer button (remote) to
change a setting on one of the submenus.

6. When you finish changing settings, press the Menu button

to go back to the Main menu. Your changes are saved
automatically.

Video Menu (Image source = Computer)

The Video menu enables you to make adjustments to the
projected image. The following options are available when the
image source is Computer.

♦

Note:

The computer must be connected and operating, and the
image source on the projector must be set to Computer for you to
access these menu options.

Menu item Description

Position Select this item and then press either multi-purpose

button(remote) or the <Enter> button(operation panel)
to enter the screen position adjustment mode. While in
the screen position adjustment mode, use the pointer
button or the <Up>, <Down>, <Left> and <Right>
buttons to move the screen position in the
corresponding direction. After you finish, press the
<Menu> button to return to the Computer Menu.

Tracking Matches the projector’s internal clock to various

computer graphic signals. Adjust this setting to
remove vertical lines from the image.

Sync Synchronizes with the tracking signal sent from the

computer. Adjust this setting whenever the overall
image is fuzzy or to remove streaks from the image.

Changing a Menu Setting

■ ■ ■ ■ ■

39

Menu item Description

Brightness Lightens or darkens the overall image. Increase

brightness to make the image lighter, or decrease it to
make the image darker.

Contrast Adjusts the relative difference between light and dark

areas. Increase contrast to make light areas lighter
and dark areas darker, or decrease it to lessen the
difference between the light areas and dark areas of
the image.

Color Adjusts the color balance of the input source.

Select this item and then press either multi-purpose
button(remote) or the <Enter> button (operation panel)
to enter the color adjustment mode.
While in the color adjustment mode, use the pointer
button or the <Up> and <Down> buttons to select a
color. Next, use the pointer button or <Left> and
<Right> buttons to adjust the selected color.
Increasing a color’s setting makes that color more
intense on the screen, while a lower setting makes the
color less intense.
After you finish, press the <Menu> button to return to
the Computer Menu.

Auto Set Up Pressing AUTO automatically adjusts the computer

input signal to the current projector settings. Press the
AUTO button while the image fills the entire screen of
your computer, like a Windows screen. Certain
computer input signals may not be totally compatible
with AUTO button settings. In such cases, use the
menus to make additional adjustments.

■ ■ ■ ■

Reset Returns all Computer Menu items to their factory

defaults. Select this item , then press either multi­purpose button(remote) or the <Enter> button
(operation panel) to display the confirmation screen.
Next, select Yes and press a multi-purpose
button(remote) or the <Enter> button (operation panel)
to reset the Computer Menu items.
If you change your mind, select No and press either
multi-purpose button(remote) or the <Enter> button
(operation panel) to clear the confirmation screen
without changing any settings.

40

■

Video Menu (Image source = Video)

The Video menu enables you to make adjustments to the
projected image. The following options are available when the
image source is Video.

♦

Note:

The video source (such as a VCR or camcorder) must be
connected and operating, and the image source on the projector
must be set to Video for you to access these menu options.

Menu item Description

Brightness Lightens or darkens the overall image. Increase

brightness to make the image lighter, or decrease it to
make the image darker.

Contrast Adjusts the relative difference between light and dark

areas. Increase contrast to make light areas lighter
and dark areas darker, or decrease it to lessen the
difference between the light areas and dark areas of
the image.

Color Adjusts color density. Increase color density to make

colors darker and more opaque, or decrease it to
make colors lighter and less opaque.

Tint (NTSC only) Adjust the red-green balance of the screen. Increase

tint to add more green, or decrease it to add more red.

Sharpness Adjusts screen sharpness.

Increase sharpness to make screen images more
sharp, or decrease it to make the images less sharp.

Reset Returns all Video Menu items to their factory defaults.

Select this item and then press either multi-purpose
button(remote) or the <Enter> button(operation panel)
to display the confirmation screen. Next, select Yes
and then press a multi-purpose button(remote) or the
<Enter> button(operation panel) to reset the Video
Menu items. If you change your mind, select No and
then press either multi-purpose button(remote) or the
<Enter> button(operation panel) to clear the
confirmation screen without changing any settings.

Changing a Menu Setting

■ ■ ■ ■ ■

41

Audio Menu

The Audio menu enables you to make adjustments related to
audio.

Menu item Description

Volume Adjusts the volume level for the speakers and audio-

Treble Adjusts the treble tone of the speakers.
Bass Adjusts the bass tone of the speakers.
SRS SPACE Adjusts sound effects. Increasing number, the sound

SRS CENTER Increasing number, the sound effects gets deeper.
Reset Returns all Audio menu items to their initial factory

out terminal. Increase the audio volume to raise the
volume, or decrease it to lower the volume.

effects gets enhanced.

defaults. Select this item and then press the <Enter>
button (operation panel) or either multi-purpose button
(remote) to display the confirmation screen.
Next, select Yes and then press the <Enter> button
(operation panel) or a multi-purpose button (remote) to
reset the Audio menu.
If you change your mind, select No and then press a
multi- purpose button (remote) or the <Enter> button
(operation panel) to clear the confirmation screen
without changing any settings.

■ ■ ■ ■

Setting Menu

The Setting menu enables you to adjust basic settings that
normally do not need changing.

Menu item Description

Prompt Temporarily displays a message on the projector

screen to identify which source (computer or video) is
providing the image.

42

■

Menu item Description

Color Temp. Adjusts the whiteness of the screen. Positive color

temperature values provide a cold white; negative
values provide a warmer white. Press the pointer
button(remote) or the <Left> and <Right>
buttons(operation panel) to change the value.
Press the <Menu> button to clear the setting screen,
and return to the Main menu.

Ceiling Flips the projected image so it looks correct when

you’re hanging the projector upside-down from the
ceiling. Selecting ON turns this feature on, while OFF
turns it off (for a normal image).

Rear Proj. Mirrors the projected image so it looks correct when

you’re projecting from behind onto a translucent
screen. Selecting ON turns mirroring on, while OFF
turned it off (for a normal image).

Blank (AV/Mute) Specifies whether a black screen, a blue screen, or a

user logo displays when the screen is blanked. See
page 45 and 46 for more information about creating a
user logo.

Video Signal Specifies the input image signal mode. Press either

multi-purpose button(remote) or the <Enter> button
(operation panel) to display the video signal system
window.
User can select from AUTO, NTSC, NTSC 4.43, PAL,
PALN, PALM, PAL60 and SECAM.

Language To display the language selection window, press either

multi-purpose button(remote) or the <Enter> button
(operation panel).
Selects the menu language: Japanese, English,
French, German, Italian, Spanish and Portuguese.

Changing a Menu Setting

■ ■ ■ ■ ■

43

Menu item Description

Reset Returns all menu items to their factory defaults.

Select this item and then press either multi-purpose
button(remote) or the <Enter> button(operation panel)
to display the confirmation screen. Next, select Yes
and then press a multi-purpose button(remote) or the
<Enter> button(operation panel) to reset the Setting
menu. If you change your mind, select No and then
press either multi-purpose button(remote) or the
<Enter> button(operation panel) to clear the
confirmation screen without changing any settings.

■ ■ ■ ■

44

■

User’s Logo Menu

The Use’s Logo menu enables you to display a custom logo
on the screen.

Follow these steps to capture and store a logo:

1. Display the image (with the projector) you wish to use as a

logo.

2. Press the Menu button to open the Menu window.

3. Select the User's Logo menu option by pressing the down

arrow button on the operation panel or the pointer button
on the remote control. Then press the Enter button
(operation panel) to display the User's Logo Setting
window.

4. The message, "Do you use this image as a user logo?"

appears on the screen. Choose Yes or No by pressing the
left or right arrow buttons (operation panel) or pressing
left or right on the pointer (remote). Then press Enter.

5. A selection box will appear over the image. To select the

portion of the image you wish to use as the logo, use the
arrow buttons (operation panel) or the pointer button
(remote). Once you have selected the desired area, press
the Enter button.

6. The message "Do you use this image?" appears on the

screen. Select Yes and press the Enter button. If you want
to change the position, select No.

7. Next, the Zoom rate setting window appears on the

screen. Select a rate using the arrow buttons or pointer,
then press the Enter button.

8. The message "Do you save this image?" appears on the

screen. Select Yes and press the Enter button. If you don't
want to save the logo, select No.

Changing a Menu Setting

■ ■ ■ ■ ■

45

♦

Note:

Saving the logo may take a moment. Do not use the
projector or other sources (computer, video, speaker, etc.) while
the logo is being saved.

9. When the message "Saving the user logo is completed"

appears on the screen, press the Menu or Enter button to
display the Main menu.

■ ■ ■ ■

46

■

Effect Menu

The Effect menu lets you select detailed settings for the effect
buttons on the remote control. Also, you can change the
cursor speed. Select the item you want to set, then press either
multi-purpose button(remote) or the <Enter> button
(operation panel) to display the detailed setting window.

Menu item Description

pointer Sets the pointer icon and size.
Box Sets the box color.
Line Sets the color and width.
Marker Sets the marker color and width.
Clear Cancels all effect functions you have previously

executed.

Cursor Speed
(LMH)

Reset Returns all effect functions to their factory defaults.

Sets the cursor speed to Low, Middle, or High.

Changing a Menu Setting

■ ■ ■ ■ ■

47

About Menu

The About menu displays information about your projector.
Press either multi-purpose button(remote) or the <Enter>
button (operation panel) to display the information.

• When the image source is Computer:

Frequency Displays H/V frequency of the computer.
Resolution Displays the output resolution of the computer video

Refresh Rate Displays the refresh rate of the computer video output.
Lamp Displays the number of hours the current projector

• When the image source is Video:

Video Signal Displays the current video signal.
Lamp Displays the number of hours the current projector

output.

lamp has been used. The lamp light turns red when
the projector lamp is near the end of its normal life.
When this happens, replace the projector lamp with a
new one as soon as possible.

lamp has been used. The lamp light turns red when
the projector lamp is near the end of its normal life.
When this happens, replace the projector lamp with a
new one as soon as possible.

■ ■ ■ ■

RESET ALL Menu

Selecting the Reset All menu option resets the settings in all
menus to their factory defaults.

While executing this command, the menu window disappears
from a screen and "RESET ALL" will be flashing on the
center of the screen.

Select this item and then press either multi-purpose
button(remote) or the <Enter> button(operation panel) to
display the confirmation screen.

48

■

Next, select Yes and then press either multi-purpose
button(remote) or the <Enter> button(operation panel) to
reset all menu items.

If you change your mind, select No and then press either
multi-purpose button(remote) or the <Enter>
button(operation panel) to clear the confirmation screen
without changing any settings.

Changing a Menu Setting

■ ■ ■ ■ ■

49

■ ■ ■ ■

50

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

■

4

Maintenance

Your projector needs little maintenance. You should keep the

lens clean because any dirt or smears appear on the screen.
You also need to periodically clean the air filter at the bottom
of the projector.

A clogged air filter can block ventilation needed to cool the
projector and keep it from overheating.

The only parts you should replace are the lamp and air filter.
If any other part needs replacing, contact your dealer or a
qualified service person.

♦

Warning:

projector and unplug the power cord. Never open any cover on
the projector, except the lamp and filter covers. Dangerous
electrical voltages in the projector can injure you severely. Do not
try to service this product yourself, except as specifically explained
in this User's Guide. Refer all other servicing to qualified service
personnel.

Before you clean any part of the projector, turn off the

■ ■ ■ ■ ■

51

Cleaning the Lens

Clean the lens whenever you notice dirt or dust on the
surface. Wipe the lens surface gently with a soft, dry, lint-free
cloth. To remove dirt or stains on the lens, moisten a soft
cloth with water and a neutral detergent and gently wipe the
lens surface.

Cleaning the Projector Case

To clean the projector case, first unplug the power cable. To
remove dirt or dust, wipe the casing with a soft, dry, lint-free
cloth. To remove stubborn dirt or stains, moisten a soft cloth
with water and a neutral detergent. Then wipe the casing.

Do not use alcohol, benzene, thinners or other chemical
detergents. These can cause the casing to warp.

■ ■ ■ ■

52

■

Cleaning the Air Filter

Clean the air filter at the bottom of the projector after every
100 hours of use. If it is not cleaned periodically, it can
become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector. To
clean the air filter, follow these steps:

1. Turn off the projector and unplug the power cable.

2. Turn the projector on its side so that the handle is on top

and you can access the filter easily.

♦

Note:

Standing the projector with the handle at the top keeps
dust from getting inside the projector housing.

3. Pull up the filter cover tab to release the filter cover.

Remove the cover.

2

1

4. The filter is attached to the inside of the filter cover. It is

recommended that you use a small vacuum cleaner
designed for computers and other office equipment to
clean the filter. If you don't have one, use a dry, lint-free
cloth.
If the dirt is difficult to remove or if the filter is torn,
replace it. Contact your dealer or call EPSON Service
Center.

5. Replace the filter cover when you're done.

Cleaning the Air Filter

■ ■ ■ ■ ■

53

Replacing the Lamp

The projector lamp typically lasts for about 2000 hours of use.
It is time to replace the lamp when:

• The projected image gets darker or starts to deteriorate.

• The projection lamp indicator is flashing orange.

• The message “LAMP REPLACE” appears on the screen

when the projector lamp comes on.

Contact your local EPSON dealer for a replacement lamp.Use
only replacement lamp part number.(ELPLP06 or ELPLP07)

♦

♦

Caution:

pressure during use, so the lamp (bulb) ruptures and burns may
occur. To avoid serious injury, before attempting to replace the
lamp, pull out the power cord plug from the outlet and wait for
the lamp (bulb) to cool (wait at least one hour).

1. Turn off the projector and unplug the power cable.

2. Place the projector on its side with the handle at the top

so you can easily access the lamp cover.

Note:

getting inside the projector housing.

This projector lamp develops high heat and high

Placing the projector in this position keeps dust from

■ ■ ■ ■

54

■

3. Use a screwdriver, coin, or similar object to loosen one

retaining screw on the lamp cover. When the screw is
loose, lift off the lamp cover. (You cannot remove this
screw from the cover.)

2

1

4. Use a screwdriver, coin, or similar object to loosen two

screws holding the lamp in position. (You cannot remove
these screws.)

5. Lift up the handle and pull out the lamp.

2

1

Replacing the Lamp

■ ■ ■ ■ ■

55

6. Gently insert the new lamp by lowering it into position.

Make sure it is inserted securely.

7. Tighten the screws you loosened in step 4.

8. Replace the lamp cover and tighten the cover screw.

(Make sure the lamp cover is securely fastened. The
projector will not run if the lamp cover is open.)

■ ■ ■ ■

56

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

■

5

Troubleshooting

This chapter describes the problems indicated by the status

lights and provides information how to solve problems with
the projector. It is divided into the following sections:

• "Problems with the Projector" on page 58 and 59 tells you

what to do if any of the projector's warning lights come on.

• "Problems with the Image or Sound" on page 60 and 61

describes what to do if you cannot project an image, if the
screen image is not good, or if there is no sound.

If you have a problem, check the appropriate section and
follow all suggestions that apply to your problem. If none of
the suggestions solve the problem, call your dealer or contact
EPSON Service Centre.

■ ■ ■ ■ ■

57

Problems with the Projector

If you have problems with the projector, first turn it off and
unplug it. Then plug the power cord back in and turn on the
projector. If this does not solve the problem, check the
warning lights at the top of the projector. These lights alert
you to problems with projector operation.

See the following pages for information on what to do when
you see these warning lights or encounter other specific
problems with the projector.

❑ The operation indicator is flashing orange and you

cannot turn on the projector.

Operation Indicator

Lamp Indicator

Temperature Indicator

■ ■ ■ ■

The lamp is cooling down. Wait until the light turns off and
then turn on the projector.

❑ The operation indicator does not come on.

Turn off the projector, check that the power cable is
connected securely both at the power outlet and the
projector, and press the Power button again.

❑ Projected images get darker or start to deteriorate,

or the lamp indicator is red.

Replace the projector lamp as described on page 54.

58

■

❑ The temperature indicator is red.

The projector is overheating, which turns the lamp off
automatically. Let the projector cool for a few minutes,
then turn it back on. Make sure nothing is blocking the
ventilation vents.

The air filter may be clogged. Clean it as described in
Chapter 4 and then let the projector cool for a while.

If the projector continues to overheat after you clean the air
filter, the problem may be caused by damage to the cooling
fan or internal circuits. Contact a qualified service person.

♦

Warning:

Except as specifically explained in this User’s Guide,

do not attempt to service this product yourself.

Problems with the Projector

■ ■ ■ ■ ■

59

Problems with the Image or Sound

❑ An image does not appear on the screen.

Check that the power light is on and the lens cover is off.
Also make sure the cables are installed correctly, as
described in Chapter 1.

The correct image source may not be selected. Press the
Source button on the remote control or the operation
panel to choose another image source.

❑ Only part of the computer image is displayed.

If the computer’s output resolution setting is higher than
1024 × 768, the projector resizes the image. If the
computer output is not compatible with this resizing,
choose a different display setting on the computer. In
Windows 3.x, use Windows Setup in the Main program
group. For a Macintosh, choose Operation Panels under
the Apple menu and then choose Monitors. In the
Monitors screen, choose Options and make sure Macintosh
Hi-Res Display or another 1024 × 768 display is selected.
For supported display settings, see “Supported Monitor
Displays (EMP-7550/7500)” on page 65 or “Supported
Monitor Displays (EMP-5550/5500)” on page 66.

■ ■ ■ ■

You also may need to modify existing presentation files if
you created them for a different resolution. See your
software manual for specific information.

❑ The message NO SIGNAL is displayed.

An image source not connected to the projector is selected,
the signal is not being output from the computer, or the
signal is not reaching the projector. Make sure the
connectors are securely attached to both the projector and
the image source. Then check that the image source is
selected correctly. When NO SIGNAL is displayed, you
cannot access the source (computer/video) menu.

60

■

❑ A blank screen is displayed.

The computer signal cannot be interpreted by the
projector. Verify the display format (see page 65 or 66).
When you see a blank screen, you cannot access the
projector menus.

❑ The image or parts of the image are blurred or not

in focus.

Adjust the Brightness and Contrast settings on the Video
main menu. If you’re viewing a computer image, also try
adjusting the Tracking and Sync buttons on the projector’s
operation panel.

There may be dirt or smears on the lens. Clean the lens as
described in Chapter 4, “Maintenance.”

❑ The colors of the image are not right.

The color balance may be incorrect. If you’re displaying a
computer image, adjust the red, green, and blue settings in
the Video menu. If you’re displaying video, adjust the
Color and Tint (NTSC only) settings on the Video menu.

❑ There is no sound.

First check that the volume setting is not turned all the way
down and that the A/V cable is securely attached to both
the projector and the audio source.

The wrong source is selected. Press either the Computer or
Video button on the remote control or operation panel to
select the proper source.

Problems with the Image or Sound

■ ■ ■ ■ ■

61

■ ■ ■ ■

62

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

■

6

Technical Specifications

General

Type of display Poly-silicon TFT
Size of liquid crystal panels 0.9 inches (22.9 mm)
Resolution EMP-5550/5500 : 800(h) × 600(v) pixels

EMP-7550/7500 : 1024(h) × 768(v) pixels

Screen size 19 - 230 inch (Tele angle)

25 - 300 inch (Wide angle)
Projection distance 3.28 - 53.46 feet (1.0 - 16.3 meters)
Remote control range 33 feet (10 meters)
Internal speaker system 1W + 1W stereo
Optical aspect ratio 4 : 3 (horizontal : vertical)
Zoom ratio 1:1.3

Projector Lamp

Type UHE Lamp (Ultra High Efficiency Lamp)
Power 120 W
Part number EMP-7500/5500 : ELPLP06

EMP-7550/5550 : ELPLP07

Mechanical

Height 3.6 inches (93 mm)

Maximum dimension

■ ■ ■ ■ ■

63

Mechanical

Width 9.3 inches (238.5 mm)

Maximum dimension
Depth 13.6 inches (346 mm)

Maximum dimension
Weight 9.4 lb (4.2 kg)

Electrical

Voltage 100 - 120 VAC and 200 - 240 VAC ± 10%
Rated frequency 50/60 Hz
Power supply 100 - 120 V, approximately 2.2 A

50/60 Hz

200 - 240 V, approximately 1.0 A

50/60 Hz

Environmental

■ ■ ■ ■

64

Temperature

Operation: 41 - 95˚ F (5 - 35˚ C),

non-condensing

Storage: 14 - 140˚ F (-10 - 60˚ C),

non-condensing
Humidity Operation: 20 - 80%,

non-condensing

Storage:10- 90%,

non-condensing

■

Supported Monitor Displays (EMP-7550/7500)

The projector displays images at a resolution of 1024 × 768
pixels. To display a higher resolution image (1280 × 1024
mode), the projector compresses the image to 1024 × 768 pixels.

The following table lists the display formats supported
by the projector:

Format Pixels Resize display Window display

PC98 640 x 400 960 x 600 640 x 400
VGA 60 640 x 480 960 x 720 640 x 480
VGAEGA 640 x 350 960 x 525 640 x 350
VESA 72/75/85 640 x 480 960 x 720 640 x 480
SVGA 56/60/72/75/85 800 x 600 1000 x 750 800 x 600
XGA 60/70/75/85 1024 x 768 1024 x 768 1024 x 768
SXGA 70/75/85 1152 x 864 1008 x 756 1152 x 864
SXGA 60/75 1280 x 1024 960 x 768 1280 x 1024
Mac 13” 640 x 480 960 x 720 640 x 480
Mac 16” 832 x 624 832 x 624 832 x 624
Mac 19” 1024 x 768 1024 x 768 1024 x 768
Mac 21” 1152 x 870 1008 x 762 1152 x 870
TV(NTSC) 640 x 480 1024 x 768 ←
TV(PAL, SECAM) 768 x 576 1024 x 768 ←

The frequencies of some computers may not allow the image
to be displayed correctly.

Supported Monitor Displays (EMP-7550/7500)

■ ■ ■ ■ ■

65

Supported Monitor Displays (EMP-5550/5500)

The projector displays images at a resolution of 800 × 600
pixels. To display a higher resolution image (1024 × 768
mode), the projector compresses the image to 800 × 600
pixels.

The following table lists the display formats supported
by the projector:

Format Pixels Resize display Window display

PC98 640 x 400 800 x 500 640 x 400
VGA 60 640 x 480 800 x 600 640 x 480
VGAEGA 640 x 350 768 x 420 640 x 350
VESA 72/75/85 640 x 480 800 x 600 640 x 480
SVGA 56/60/72/75/85 800 x 600 800 x 600 800 x 600
XGA 60/70/75/85 1024 x 768 768 x 576 1024 x 768
SXGA 70/75 1152 x 864 768 x 576 1152 x 864
Mac 13” 640 x 480 800 x 600 640 x 480
Mac 16” 832 x 624 800 x 600 832 x 624
Mac 19” 1024 x 768 768 x 576 1024 x 768
Mac 21” 1152 x 870 768 x 580 1152 x 870
TV(NTSC) 640 x 480 800 x 600 ←
TV(PAL, SECAM) 768 x 576 800 x 600 ←

■ ■ ■ ■

66

♦

♦

The frequencies of some computers may not allow the image
to be displayed correctly.

Note:

The frequencies of some computers may not allow the

image to be displayed correctly.

Note:

This projector is compatible with DDC-capable graphic

sub-systems and boards only.

■

Monitor and Computer connector pin assignments

The Monitor and Computer connectors are female video
RGB, 15-pin micro-D-style connectors. The pin assignments
are:

Input pin Signal
1 Red analogue input
2 Green analogue input
3 Blue analogue input
4 GND
5 GND
6 Red GND
7 Green GND
8 Blue GND
9 Reserved
10 Sync GND
11 GND
12 SDA (DDC)
13 Horizontal sync/composite sync input
14 Vertical sync input
15 SCL (DDC)

Monitor and Computer connector pin assignments

■ ■ ■ ■ ■

67

■ ■ ■ ■

68

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

■

Glossary

Brightness. The balance of light and dark shades in an
image.

Composite video. A type of video signal that encodes
colours, luminance and sychronization information so it can
be carried in one signal.

Contrast. A measure of the luminance differences between
the highlights and shadows of an image. In a high-contrast
image, light areas are very bright and dark areas are very dark.

NTSC. A 525-line video broadcast format developed by the
National Television Standards Committee. NTSC is widely
used in North America, Mexico and Japan.

PAL (Phase Alternation by Line). A 625-line video
broadcast format used in Western Europe, India, China,
Australia, New Zealand and parts of Africa.

Resolution. A measure of the amount of detail contained in
an image. Resolution can be measured in dots per inch or in
pixels. Image sharpness and clarity improve as resolution
increases.

RGB. Red Green Blue
S-Video. A type of video signal which transmits luminance

and colour separately.

SECAM (Système Electronique pour Couleur Avec
Mémoire). A 625-line TV system used in France, Eastern

Europe, Russia and parts of Africa.

■ ■ ■ ■ ■

69

Serial. A type of communication interface that transmits data
over a single wire.

Sleep mode. The power cable is connected but the projector
is switched off. In this mode the power LED lights up orange.
If the projector is not used for 30 minutes the lamp switches
itself off and after 30 seconds the projector goes into sleep
mode.

■ ■ ■ ■

70

Glossary

■

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Index

A

A/V cable 2
About Menu 48
Audio cable 2
Audio Menu 42
Auto 40
Auto Set Up 40
AV/Mute 30, 32
AVTSS vii

B

Bass 42
BIS CUIT viii
Blank 43
bottom multi-purpose button 29
Brightness 40, 69

C

Ceiling 43
Cleaning the Air Filter 53
Color 40
Color Temp. 43
Composite video 69
Computer cable 2

Contrast 40, 69
Custom 30

E

Effect Menu 47
Effects buttons 30
ELP LINK III viii
Enter button 31

F

FAQ’s xv
focus ring 22, 25
Focusing 25
foot adjust lever 26
Freeze 30
Frequency 48

G

Glossary 69

I

Installation xi

L

Lamp 48
Lamp Indicator 33, 34
Language 43

■ ■ ■ ■ ■

71

M

Main Menu 36
Maintenance xi, 51
Monitor Displays 65, 66
Mouse cable 2

N

NTSC viii, 69

Refresh Rate 48
Remote control ix
remote control 28
Replacing the Lamp 54
Reset 40
RESET ALL Menu 48
Resize Button 27
Resize button 27
Resolution 48, 69
RGB 69

O

Operation Indicator 33
operation panel 22
Optional Accessories x
Options Menu 42

P

PA System 18
PA system 1
PAL viii, 69
pin assignments 67
pointer button 29
Position 39
Positioning the Screen Image 25
Projector 2
Projector Menus 35
Projector Status Indicators 33
Prompt 42

R

RCA/3.5 mm cable 19
rear feet clockwise 26
Rear Proj. 43

S

Safety Instructions xii
SECAM viii, 69
Serial 70
Sharpness 41
Sleep Mode 24
Sleep mode 70
SRS 3D sound vii
SRS CENTER 42
SRS SPACE 42
sub-menu 38
S-Video viii, 69
S-Video cable 3
SXGA viii
Sync 39

T

Technical Specifications xi
Temperature Indicator 33
Tint 41
top multi-purpose button 29
Tracking 39
Treble 42
Troubleshooting xi, 57

■ ■ ■ ■

72

Index

■

true XGA vii

V

VGA viii
video source vii
Volume 42

W

World Wide Web xv

X

XGA viii

Z

Zoom ratio 63
zoom ring 22, 25

■ ■ ■ ■ ■

73

■ ■ ■ ■

74

Index

■ ■ ■ ■ ■

■

75

■ ■ ■ ■

76

Index

英



Printed in Japan

75416861