Epson EcoTank ET-2760 Start Guide

ET-2760

2

Fill ink tanks

5 When the ink tank is full, remove the ink

bottle and replace the bottle cap. Place the
remaining ink aside; you will need it later.

12 When the message to see the Start Here sheet appears

on the LCD screen, press the OK button. On the next
screen, press and hold the help button for 3 seconds.

Start Here

IMPORTANT: Before using this product, make sure you read
these instructions and the safety instructions in the online User’s
Guide.

1

Unpack

Note: Do not open the ink bottles until you are ready to fill the ink

tanks. The ink bottles are vacuum packed to maintain reliability.

1 Remove all protective materials from the product.

Warning: Keep the ink bottles out of the reach of children and do not

drink the ink.

Caution: This product requires careful handling of ink. If ink spills,

wipe it off immediately with a damp towel to avoid permanent stains. If
ink gets on your clothes or belongings, it may not come off.

Note:

• Epson cannot guarantee the quality or reliability of third-party ink.

• Use the ink bottles included with the printer to set up the product.
Part of the ink will be used to charge the print head. These bottles
may print fewer pages compared with replacement ink bottles.

1 Open the ink tank cover, then open the cap for the black

ink tank.

2 Unpack the black (BK) ink bottle. Hold the ink bottle

upright and slowly turn the bottle cap to remove it.

Note: Do not leave the ink bottle inserted;

otherwise the bottle may be damaged or ink
may leak.

6 Close the ink tank cap.

13 When the message to start initialization appears on the

LCD screen, press the start button to start charging
the ink. Ink charging takes approximately 10 minutes. A
message appears when ink charging is complete. Press
the OK button to continue.

7 Repeat the previous steps for the other colors.

8 Close the ink tank cover and then the scanner unit.

Caution: Do not turn off the product, raise the scanner unit, or

load paper while the product is charging or you’ll waste ink.

9 Connect the power cord to the back of the product and to

an electrical outlet.

2 Lift up the scanner unit. Remove all protective materials

from inside the product.

Caution: Do not touch the flat white cable or the ink tubes and

their translucent cover.

Caution: Do not shake or squeeze the ink bottles. Do not touch

the top of the ink bottle after its cap is removed.

3 Insert the ink bottle into the filling port, as shown below.

Note: Refer to the color-coded sticker on the ink tank unit to

identify the color of each tank. Do not force the bottles into
position; they are keyed for each color.

4 Wait for the ink to fill the tank.

Do not squeeze the bottle. Ink
flows into the tank and stops
automatically when the ink is
filled to the upper line.

Note: If ink does not flow from the

bottle, lift and reinsert the bottle.

Caution: Do not connect to your computer yet.

10 Raise the control panel, then press the power button to

turn on the product.

Note: If an error message appears, turn off the product and

check that no protective material has been left inside the product.

11 Press or to select your language on the LCD screen,

then press the OK button.

Note: You can change this setting later using the product’s

control panel. For more information, see the online User’s Guide.

Note: The included ink bottles are designed for reliable printer

setup and cannot be resold. After setup, the remaining ink is
available for printing.

14 To complete filling the ink tanks, repeat steps 1 through 7

using the remaining ink in the bottles.

Note: Replace the bottle cap before disposing of the bottles.

15 Close the ink tank cover and scanner unit.

16 Select Maintenance > Reset Ink Levels, then follow the

on-screen instructions to reset the ink levels.

17 Follow the on-screen instructions to adjust the print

quality. Press the OK button to continue.

Note:

• You need to load paper before you can adjust the print quality. See
“Load paper” on the back of this sheet for details.

• You can change these settings later using the product’s control
panel. For more information, see the online User’s Guide.

Caution: After setup, periodically

inspect the ink level to ensure it is
not below the lowest line on the tank.
Prolonged use when ink is below
the lowest line could damage the
product. See the online User’s Guide
for refilling instructions.

Follow steps 12 and 13 to continue ink charging.

3

Load paper

See the online User’s Guide for information about loading
capacity, available paper types and sizes, and loading
envelopes.

1 Make sure the product is not charging ink. Then flip the

feeder guard forward, raise the paper support, and tilt it
backwards slightly.

2 Slide the edge guides all the way out.

3 Load paper, glossy or printable side up and short edge

first, in the middle of the rear paper feed slot.

4 Slide the edge guide against the paper, but not too tightly.

4

Install software

Note:

• An Internet connection is required to obtain the product software.

• To print from a Chromebook™, go to

www.epson.com/support/gcp (U.S.) or
www.epson.ca/support/gcp (Canada) for instructions.

1 Make sure the product is NOT CONNECTED to your

computer.

Windows®: If you see a Found New Hardware screen, click

Cancel and disconnect the USB cable.

2 Download and run your product’s software package:

www.epson.com/support/et2760 (U.S.) or
www.epson.ca/support/et2760 (Canada)

3 Follow the instructions on the computer screen to run the

setup program.

4 When you see the Select Your Connection screen, select

one of the following:

• Wireless connection

In most cases, the software installer automatically
attempts to set up your wireless connection. If setup
is unsuccessful, you may need to enter your network
name (SSID) and password.

• Direct USB connection

Make sure you have a USB cable (not included).

Any problems?

Network setup was unsuccessful.

• Make sure you select the right network name (SSID).

• Restart your router (turn it off and then on), then try to
connect to it again.

• The printer can only connect to a network that supports

2.4 GHz connections. If your router offers both 2.4 GHz and
5 GHz connections, make sure 2.4 GHz is enabled.

• If you see a firewall alert message, click Unblock or Allow
to let setup continue.

• If your network has security enabled, make sure you enter
your network password (WEP key or WPA passphrase)
correctly. Be sure to enter your password in the correct
case.

• Print a network connection report to identify network
problems and solutions. See your online User’s Guide for
instructions.

There are lines or incorrect colors in my printouts.

Run a nozzle check to see if any of the nozzles are clogged.
Then clean the print head, if necessary. See the online User’s
Guide for more information.

The product’s screen is dark.

Make sure your product is turned on, and press any button to
wake it from sleep mode.

Setup is unable to find my product after connecting it
with a USB cable.

Make sure your product is on and securely connected as
shown:

Videos

Visit www.epson.com/support/et2760videos (U.S.) or
www.epson.ca/support/et2760videos (Canada) to view

support videos.

Technical support

Visit www.epson.com/support/et2760 (U.S.) or
www.epson.ca/support/et2760 (Canada) to download drivers,

view manuals, get FAQs, or contact Epson.

Call [phone] (U.S.) or [phone] (Canada), 6 am to
8 pm Pacific Time, Monday through Friday, and 7 am to 4 pm,
Pacific Time, Saturday. Days and hours of support are subject
to change without notice. Toll or long distance charges may
apply.

Recycling

Epson offers a recycling program for end of life hardware and
ink bottles. Please go to www.epson.com/recycle (U.S.) or
www.epson.ca/recycle (Canada) for information on how to
return your products for proper disposal.

Need paper and ink?

Ensure brilliant results with Epson specialty
and plain papers, engineered specifically for
Epson printers. Find Epson papers and Epson
Genuine Ink at www.epson.com (U.S. sales)
or www.epson.ca (Canadian sales) and at
Epson authorized resellers. Call
800-GO-EPSON (800-463-7766).

ET-2760 replacement inks

5 Pull out the output tray.

6 Select the paper settings on the product’s control panel.

Mobile and voice-activated
printing

• Print directly from your iOS device. Simply connect your
printer and device to the same network and tap the action
icon to select the print option.

• Print directly from your Android™ (v4.4 or later) device*.
Simply connect your printer and device to the same network
and tap the menu icon to select the print option.

• Print from wherever you are, next to your printer or remotely,
with Epson Connect™ and Google Cloud Print™. Learn
more at www.epson.com/connect (U.S.) or
www.epson.ca/connect (Canada).

• Use voice-activated assistants to print a variety of creative
and everyday items from your Epson® product. Simply add
your product to an Epson Connect account, then link the
account to a voice-activated assistant. See
www.epson.com/voice (U.S.) or www.epson.ca/voice
(Canada) for more information.

* May require the Epson Print Enabler or Mopria Print Service app from

Google Play™.

Any questions?

User’s Guide

Windows: Click the icon on your desktop or Apps screen to

access the online User’s Guide.

Mac: Click the icon in Applications/Epson Software/Guide to
access the online User’s Guide.

If you don’t have a User’s Guide icon, go to the Epson website,
as described below.

Color Part number

Black 502

Cyan 502

Magenta 502

Yellow 502

EPSON is a registered trademark, EPSON Exceed Your Vision is a registered logomark, and
Epson Connect is a trademark of Seiko Epson Corporation.

Designed for Excellence is a trademark of Epson America, Inc.

Mac is a trademark of Apple Inc., registered in the U.S. and other countries.

Windows is a registered trademark of Microsoft Corporation in the United States and/or other
countries.

Android, Chromebook, Google Cloud Print, and Google Play are trademarks of Google LLC.

General Notice: Other product names used herein are for identification purposes only and may
be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

© 2019 Epson America, Inc., 1/19

Printed in XXXXXX CPD-57026