Emko ESM-3710-N User manual [ml]

ESM-3710-N 77 x 35 DIN Size

Digital , ON / OFF Temperature

Controller

- 4 Digits Display

- NTC Input or
PTC Input or

J Type thermocouple Input or,
K Type thermocouple Input or,
2-Wire PT-100 Input or,
2-Wire PT-1000 Input

- Adjustable temperature offset

ON/OFF temperature control

-

- Selectable heating or cooling function

- Selection of operation with hysteresis

- Adjustable temperature offset

- Set value low limit and set value high limit boundaries

- Operation selection of compressor operates continuously,
stops or operates periodically in case of sensor defect

- Compressor protection delays

- Adjustable internal buzzer according to sensor defect status.

- Password protection for programming section

- Installing parameters using Prokey

ESM-3710-N 77x35 DIN Size Temperature Controller

- Remote access, data collecting and controlling with Modbus RTU

- Having CE mark according to European Norms

(Must be determined in order.)

Instruction Manual. ENG ESM-3710-N 01 V07 11/18

ENGLISH

1.Preface

ESM-3710N series temperature controllers are designed for measuring and controlling
temperature. They can be used in many applications with their On / Off control form, heating
and cooling control form and easy-use properties. Some application fields which they are
used are below:

Application Fields Applications

Glass Heating
Food Baking Ovens
Plastic Incubators
Petro-Chemistry Storages
Textile, Automative Air Conditioning
Machine Production Industries Etc... Etc...

1.1 Environmental Ratings

Operating Temperature : -20 to 70 °C

Max. Operating Humidity : 90% Rh (non-condensing)

Altitude : Up to 2000 m.
Forbidden Conditions:

Corrosive atmosphere

c

Explosive atmosphere
Home applications (The unit is only for industrial applications)

1.2 General Specifications

Standard

230V ( %15) 50/60HzV ±

Optional Supply Voltage

V

115 V (±%15) 50/60Hz,

V

24 V (±%15) 50/60Hz,

W

24 V (±%15) 50/60Hz,
10

- 30 V Z

NTC, PTC,
J or K Type TC
2-Wire PT-100
2-Wire PT-1000

ESM-3710-N

Power Supply
Input

Temperature Sensor
Input

Standard

Output-1
(Relay Output)

Optional

Output-1
(SSR Drive Output)

Control Output

Alarm Output

Control Output

Alarm Output

Heating or Cooling

Function

ON/OFF Operation

2

1.3 Installation

A visual inspection of this product for possible damage occurred during shipment is
recommended before installation. It is your responsibility to ensure that qualified mechanical
and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit, power off the
system and separate the electrical connection of the device from the system.

The unit is normally supplied without a power supply switch or a fuse. Use power switch and fuse
as required.

Be sure to use the rated power supply voltage to protect the unit against damage and to prevent
failure.

Keep the power off until all of the wiring is completed so that electric shock and trouble with the
unit can be prevented.

Never attempt to disassemble, modify or repair this unit. Tampering with the unit may results in
malfunction, electric shock or fire.

Do not use the unit in combustible or explosive gaseous atmospheres.

During putting equipment in hole on the metal panel while mechanical installation some metal
burrs can cause injury on hands, you must be careful.

Montage of the product on a system must be done with it’s fixing clamps. Do not do the montage
of the device with inappropriate fixing clamp. Be sure that device will not fall while doing the
montage.

It is your responsibility if this equipment is used in a manner not specified in this instruction
manual.

1.4 Warranty

EMKO Elektronik warrants that the equipment delivered is free from defects in material and
workmanship. This warranty is provided for a period of two years. The warranty period starts
from the delivery date. This warranty is in force if duty and responsibilities which are determined
in warranty document and instruction manual performs by the customer completely.

1.5 Maintenance

Repairs should only be performed by trained and specialized personnel. Cut power to the
device before accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of
these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in
ethyl alcohol or water to clean the external plastic case.

1.6 Manufacturer Company

Manufacturer Information:

Emko Elektronik Sanayi ve Ticaret A.Ş.
Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA/TURKEY
Phone : [phone]
Fax : [phone]

Repair and maintenance service information:

Emko Elektronik Sanayi ve Ticaret A.Ş.
Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA /TURKEY
Phone : [phone]
Fax : [phone]

3

2. General Description

Front Panel
IP65 protection
NEMA 4X

Panel Surface
(maximum thickness 15 mm / 0.59 inch)

Mounting Clamp

2.1 Front View and Dimensions of ESM-3710-N Temperature Controller

Maximum 15 mm / 0.59 inch

O

C

ESM3710-N

O

S

P

F

SET

P

ü

34,5 mm / 1.36 inch

76 mm / 3 inch

2.2 Panel Cut-Out

29 mm / 1.14 inch

6 mm / 0.24 inch

110 mm / 4.33 inch (min)

71 mm / 2.79 inch

65 mm / 2.56 inch

50 mm / 1.97 inch (min)

4

2.3 Panel Mounting

1

3

2

1-Before mounting the device in your panel,
make sure that the cut-out is of the right size.

2-Insert the device through the cut-out. If the
mounting clamps are on the unit, put out them
before inserting the unit to the panel.

3- Insert the mounting clamps to the fixing sockets
that located left and right sides of device and make
the unit completely immobile within the panel

3

2.4 Removing from the Panel

1-Pull mounting clamps from left and right fixing
sockets.

2-Pull the unit through the front side of the panel

1

2

Before starting to remove the unit from
panel, power off the unit and the related
system.

c

3. Using Prokey

TO USE PROKEY, VALUE OF THE PrC PARAMETER MUST BE ‘0’.
IF PrC=1 AND BUTTON IS PRESSED MESSAGE WILL BE SHOWN. 10s. LATER
DEVICE TURNS BACK TO THE MAIN OPERATION SCREEN OR YOU CAN PRESS SET
BUTTON TO TURN BACK TO MAIN OPERATION SCREEN.

DOWNLOADING FROM DEVICE TO PROKEY

1.The device is programmed by using the parameters.

2.Energize the device then put in PROKEY and press button. Message is shown on the
display. When the loading has finished, message is shown.

3.Press any button to turn back to main operation screen.

4.Remove the PROKEY.

NOTE: message is shown when an error occurs while programming. If you want to reload, put

in PROKEY and press button. If you want to quit, remove PROKEY and press button. The

device will turn back to main operation screen.

DOWNLOADING FROM PROKEY TO DEVICE

1.Switch off the device.

2.Put in PROKEY then energize the device.

3.When the device is energized, the parameter values in PROKEY, start downloading to the device
automatically. At first, message is shown on the display, when loading has finished,
message is shown.

4.After 10 seconds device starts to operate with new parameter values.

5.Remove the PROKEY.

NOTE: message is shown when an error occurs while programming. If you want to reload,
switch off the device and put in PROKEY then energize the device. If you want to quit remove
PROKEY and press button. The device will turn back to main operation screen.

5

4. Electrical Wiring Diagram

N

a

L

3

21 4 5 6 7

(-)

P/N : ESM-3710-N

Electrical Wiring Diagram for 30(15)A @ 240 V V Relay Output Devices:

P/N : ESM-3710-N

(+)

For SSR Output

N

a

L

3 4
21 5 6 7 8

4.1 Supply Voltage Input Connection of the Device

Power Supply Connection

L

N

a

(+)(-)

4

5

EXTERNAL

FUSE
(1A T)

Note-1

Supply

Switch

c

Supply Voltage

V ±

230V ( %15) 50/60Hz ,

V ±

115V ( %15) 50/60Hz,

V ±

24V ( %15) 50/60Hz ,

W ±

24V ( %15) 50/60Hz ,

10..30 V - 1.5 W

Z

Must be determined in order.

Note-1 : External fuse is recommended.

Make sure that the power supply voltage is the same
indicated on the instrument.

c

Switch on the power supply only after that all the electrical
connections have been completed.
Supply voltage range must be determined in order. While
installing the unit, supply voltage range must be controlled
and appropriate supply voltage must be applied to the unit.

There is no power supply switch on the device. So a power
supply switch must be added to the supply voltage input.

c

Power switch must be two poled for seperating phase and
neutral, On/Off condition of power supply switch is very
important in electrical connection.

External fuse that on Vpower supply inputs must be on
phase connection.
External fuse that on Zpower supply inputs must be on (+)
connection.

Temperature Sensor

TC,NTC,PTC,PT-100
or PT-1000

Supply Voltage Input

V ±

230V ( %15) 50/60Hz

V ±

115V ( %15) 50/60Hz

V ±

24V ( %15) 50/60Hz

10...30 V

Z

Must be determined in order.

Relay or SSR Output

Temperature Sensor

NTC

Supply Voltage Input

V ±

230V ( %15) 50/60Hz

V ±

115V ( %15) 50/60Hz

V ±

24V ( %15) 50/60Hz

10...30 V

Z

Must be determined in order.

Relay Output

30(15)A@240 V V

Input

Input

6

Supply Voltage InputConnection for 30(15)A @ 240 V V Relay Output Devices:

L

N

EXTERNAL

FUSE
(1A T)

a

(+)(-)

5

6

Note-1

Supply
Switch

V ±

230V ( %15) 50/60Hz ,

V ±

115V ( %15) 50/60Hz,

V ±

24V ( %15) 50/60Hz ,

W ±

24V ( %15) 50/60Hz ,

10..30 V - 1.5 W

Z

Must be determined in order.

c

Supply Voltage

4.2 Device Label and Connection Diagram

230VV CONNECTION DIAGRAM

P/N : ESM-3710-N - 5.18.0.1/00.00/2.3.0.0

16(8)A @

230 VV ± 15%

250VV1HP

50/60Hz - 1.5VA

OUTPUT

NO NCC

LINE

LOAD

7

NTC

INPUT SCALE

(-50 ,100 ; -58 ,212 ) °C °C °F °F

RS-485

PROKEY

or

L

N

30(15)A @ 240 V V Connection Diagram for Relay Output Devices:

P/N:ESM-3710-N-5.18.0.3/00.00/2.3.0.0

30(15)A @ 240VV

230 VV ± 15%

OUTPUT

50/60Hz - 1.5VA

7 8

NTC

INPUT SCALE

(-50 ,100 ; -58 ,212 ) °C °C °F °F

RS-485

PROKEY

or

L

N

5.Front Panel Definition and Accessing to the Menus

5 6 7 7

1

2

BUTTON DEFINITIONS

1. Increment Button :

** It is used to increase the value in the Set screen and Programming mode.

2. Decrement, Silencing Buzzer and Downloading to Prokey Button :

** It is used to decrease the value in the Set screen and Programming mode.
** It is used to silence the buzzer.
** If Prc =0, it is used to download from device to prokey.

6

16A Fuse

30A Fuse

@250VV1HP

1

1

8

O

O

C

16(8)A

OUTPUT

C

2

30(15)A@240VV

OUTPUT

2

F

LOAD

9

S

3

3

LOAD

10

NCNO

P

ESM3710-N

SET

P

ü

a

4

5

L

N

a

54

6

L

N

3

3

4

RS-485

or

PROKEY

6

7

NTC

RS-485

or

PROKEY

7

8

NTC

7

3. Set Button :

** In the main operation screen; if this button pressed, set value will be displayed. Value can be
changed using increment and decrement buttons. When Enter button pressed, value is saved
and returns back to main operating screen.
** To access the programming screen; in the main operation screen, press this button for 5
seconds.

4. Enter Button :

** It is used to saving value in the Set screen and programming screen.

LED DEFINITIONS

5. Cooling led :

** This led indicates that cooling control is selected and process output relay is active. If any
of compressor protection time active, this led blinks.

6.Heating led :

** This led indicates that heating control is selected and process output relay is active.

7.Celcius led :

** Indicates that device is in C mode.

8.Fahrenheit led :

** Indicates that device is in F mode.

9.Set led :

** Indicates that device is in Set value changing mode.

10.Program led :

**Blinks in programming mode .

6. Changing and Saving Temperature Set Value

Main Operation Screen

When SET button pressed ‘’S’’ led will

be active and temperature set value will

Temperature set value parameter (Default=50) MODBUS ADDRESS:40001

Temperature set value, can be programmed between minimum temperature set value and

maximum temperature set value .

be displayed.

When ENTER button pressed

temperature set value can be saved.

6.1 Programming Mode Parameter List

o

o

O

ESM3710-N

O

S

P

C

F

SET

P

ü

O

ESM3710-N

O

S

P

C

F

SET

P

ü

ü

SET Value Screen

O

ESM3710-N

O

S

P

C

F

SET

P

ü

Temperature set value can

be changed with increment

and decrement buttons.

Main Operation Screen

O

‘’S’’ will be inactive and goes back to

main operation screen.

ESM3710-N

O

S

P

C

F

SET

P

ü

ü

Temperature Unit Selection Parameter ( Default = 0 ) MODBUS ADDRESS:40002

°C selected.
°F selected.

Decimal Seperator Enabling Parameter ( Default = 0 ) MODBUS ADDRESS:40003

Disable.
Enable.

8

Note: If sensor input type is selected J, K, PT-100 or PT-1000 (BC =05,10,11 or 14) parameter is

skipped.

Hysteresis Parameter for Compressor Output ( Default = 1 )
MODBUS ADDRESS:40004

from -20 to 20 °C for NTC(-50°C, 100°C) or PTC(-50°C, 150°C) or J Type TC (0°C,800°C)

or J Type TC (0°C,1000°C) or PT-100(-50°C, 400°C)or PT-1000 (-50°C, 150°C) or
PT-100 (-20°C, 100°C), from -36 to 36 °F for NTC(-58°F, 212°F) or PTC (-58°F, 302°F) or J
Type TC (32°F,1472°F) or or K Type TC (32°F,1830°F) or PT-100(-58°F, 752°F) or
PT-1000(-58°F, 752°F) or PT-100(-4°F, 212°F), from -10.0 to 10.0°C for NTC
(-50.0°C,100.0°C) or PTC(-50.0°C,150.0°C) or PT-100 (-19.9°C,99.9°C), from -18.0 to

18.0°F for NTC (-58.0°F,212.0°F) or PTC (-58.0°F,302.0°F) or PT-100 (-4.0°F,212.0°F),

In ON/OFF control algorithm, temperature
value is tried to keep equal to set value by
opening or closing the last control element.
ON/OFF controlled system, temperature
value oscillates continuously. Temperature
value’s oscillation period or amplitude around
set value changes according to controlled
system. For reducing oscillation period of
temperature value, a threshold zone is formed
below or around set value and this zone is
named hysteresis.

Minimum Temperature Set Value Parameter (Default = Minimum Value of Device
Scale ) MODBUS ADDRESS:40005

Temperature set value can not be lower than this value.
This parameter value can be adjusted from minimum value of device scale to maximum
temperature set value parameter

Maximum Temperature Set Value Parameter (Default = Maximum Value of Device
Scale ) MODBUS ADDRESS:40006

Temperature set value can not be bigger than this value.
This parameter value can be adjusted from minimum temperature set value parameter
to maximum value of the device scale

Sensor Offset Parameter ( Default = 0 ) MODBUS ADDRESS:40007

from -20 to 20 °C for NTC(-50°C, 100°C) or PTC(-50°C, 150°C) or J Type TC (0°C,800°C) or

J Type TC (0°C,1000°C) or PT-100(-50°C, 400°C)or PT-1000 (-50°C, 150°C) or
PT-100 (-20°C, 100°C), from -36 to 36 °F for NTC(-58°F, 212°F) or PTC (-58°F, 302°F) or J
Type TC (32°F,1472°F) or or K Type TC (32°F,1830°F) or PT-100(-58°F, 752°F) or
PT-1000(-58°F, 752°F) or PT-100(-4°F, 212°F), from -10.0 to 10.0°C for NTC
(-50.0°C,100.0°C) or PTC(-50.0°C,150.0°C) or PT-100 (-19.9°C,99.9°C), from -18.0 to

18.0°F for NTC (-58.0°F,212.0°F) or PTC (-58.0°F,302.0°F) or PT-100 (-4.0°F,212.0°F),

Operating Type Parameter ( Default = 0) MODBUS ADDRESS:40008

If parameter value is ‘0’ device skips to parameter

Temperature

Set

Control
Output

ON

OFF

HSt

HSt

Time

Time

Heating

Cooling

Compressor Start Delay at Power On Parameter ( Default = 0)
MODBUS ADDRESS:40009

When power is first applied to the device, compressor is on when this time delay is expired.
It can be adjusted from 0 to 20 minutes.

9

Compressor Stop-Start Delay Parameter ( Default = 0) MODBUS ADRES:40010

When compressor is inactive, this time delay must be expired for activation of the
compressor. It can be adjusted from 0 to 20 minutes

Compressor Start-Start Delay Parameter ( Default = 0) MODBUS ADRES:40011

This time delay must be expired between two activation of the compressor. It can be
adjusted from 0 to 20 minutes.

Sensor Defect Parameter ( Default = 0 ) MODBUS ADRES:40012

Compressor is OFF in case of sensor defect.
Compressor is ON in case of sensor defect.
Compressor operates periodically according to and Time periods in

case of sensor defect.

Compressor is active during this time period in case of probe defect (Default = 0)
MODBUS ADRES:40013

If probe defect parameter is 2, then this parameter is observed. It can be adjusted
from 0 to 99 minutes.

Compressor is inactive during this time period in case of probe defect
( Default = 0 )MODBUS ADRES:40014

If probe defect parameter is 2, then this parameter is observed. It can be adjusted
from 0 to 99 minutes.

Buzzer Function Selection Parameter ( Default = 0 ) MODBUS ADDRESS:40015

Buzzer is inactive.
Buzzer is active during sensor failures.

Buzzer is active during this time

If buzzer function selection parameter value =0, this parameter can not be
observed. Buzzer stays active during this time. It can be adjusted from 1 to 99 minutes

When this parameter is 1, if decrement button is pressed, is observed. In this
condition buzzer is active till buzzer silence button is pressed.

Communication Mode Selection Parameter ( Default = 0 ) MODBUS ADDRESS:40017

PROKEY communication selected.
Rs485 communication selected.

Slave ID Parameter ( Default = 1 ) MODBUS ADDRESS=40018

Device communication address parameter (1 to 247).

Programming Section Accessing Password . ( Default = 0 ) MODBUS ADDRESS:40019

It is used for accessing to the programming section. It can be adjusted from 0 to 9999. If it is
selected 0, password will not be asked

, , , , and Parameters are observed if Operation type

i

is selected “Cooling”. If operation type is selected “Heating ” ,skip to the parameter

( Default = ) MODBUS ADDRESS:40016

6.2 Modbus Adresses of Device Status Parameters (Read Input Register)

MODBUS ADDRESS:30001 Temperature Value
MODBUS ADDRESS:30002 Reserved
MODBUS ADDRESS:30003 Led Status : 0.bit C Led,

A

6.bit Compressor Led,

A

13.bit Program Led, 14.bit Set Led
MODBUS ADDRESS:30004 Device Status : 1.bit Buzzer Status

A

2.bit Sensor Lost Status
MODBUS ADDRESS:30005 Output Status
MODBUS ADDRESS:30006 Device Type and Device Version

o

10

6.3 Operation Graphics of ESM-3710-N ControllerTemperature

1-If Operating Type Parameter Value = 1 (Cooling),
Switch On Delay After Power On Parameter Value ³ 1 ,
Compressor Stop/Start Time Delay Parameter Value ³ 1 and
Compressor Start/Start Time Delay Parameter Value ³ 1;

Power

°C

SET

Output

Led

Output

2-If Operating Type Parameter Value = 0 (Heating),

i

Hst

Temperature

Value

SET

ON

OFF

to set value by opening or closing the last control element. ON/OFF controlled
system, temperature value oscillates continuously. Temperature value’s oscillation
period or amplitude around set value changes according to controlled system. For
reducing oscillation period of temperature value, a threshold zone is formed below or
around set value and this zone is named hysteresis. Action of control output is
described with figures above.

HSt

Temperature Control Output

HSt HSt

In ON/OFF control algorithm, temperature value is tried to keep equal

Time

Time

Time

Time

Time

Time

6.4 Failure Messages in ESM-3710-N Temperature Controller

Screen Blinking
Sensor failure . Sensor connection is wrong or there is no sensor connection. If buzzer function
selection parameter is 1, internal buzzer starts to operate.

11

6.5 Entering To The Programming Mode, Changing and Saving Parameter

Main Operation Screen

ESM3710-N

O

O

S

P

C

F

SET

P

O

O

S

C

F

ü

P

ESM3710-N

SET

P

ü

When SET button is pressed for 5

seconds, “P” led starts to blink. If

programming mode entering
password is different from 0,

programming mode entering screen

will be observed.

O

O

S

P

C

F

Note1: If programming

mode accessing
password is 0,
Temperature Unit screen
is observed instead of
programming screen

ESM3710-N

SET

P

Programming Mode

Entering Screen

Press OK button for

accessing to the

password entering

screen.

O

O

C

ü

Password Entering Screen

Enter programming mode accessing password

with increment and decrement buttons.

Note2: If programming mode accessing password is 0, only three parameters
are accessible, and the parameter values can be changed.

Programming Screen

ESM3710-N

O

O

S

P

C

F

SET

P

Password Entering Screen

Press OK button for entering

the password.

O

O

C

ü

Press SET button for accessing to the parameter
value. Press increment button for accessing to the
next parameter, press decrement button for
accessing to the previous parameter.

ESM3710-N

O

O

S

P

C

F

SET

P

Hysteresis Value for
Compressor Output

Change the value with increment

and decrement buttons.

O

O

C

ü

Hysteresis Value for

Compressor Output

Press OK button for saving the

parameter.

If no operation is performed in programming mode for 20 seconds, device turns to main

i

operation screen automatically..

Press increment button for accessing to the
next parameter, press decrement button for
accessing to the previous parameter

Hysteresis Parameter for

Compressor Output

ESM3710-N

S

P

F

SET

P

ü

ESM3710-N

S

P

F

SET

P

ü

ESM3710-N

S

P

F

SET

P

ü

12

7. Specifications

Device Type : Temperature Controller
Housing & Mounting : 76mm x 34.5mm x 71mm plastic housing for panel

Protection Class : NEMA 4X (Ip65 at front, Ip20 at rear).
Weight : Approximately 0.20 Kg.
Environmental Ratings : Standard, indoor at an altitude of less than 2000 meters

Storage / Operating Temperature : -30 C to +80 C / -20 C to +70 C
Storage / Operating Humidity : 90 % max. (None condensing)
Installation : Fixed installation
Overvoltage Category : II.
Pollution Degree : II, office or workplace, none conductive pollution
Operating Conditions : Continuous
Supply Voltage and Power :

:10 - 30

Temperature Sensor Input : NTC, PTC, TC, RTD
NTC input type : NTC (10 kW @25 °C )
PTC input type : PTC (1000 W @25 °C )
Thermocouple input type : J, K (IEC584.1) (ITS 90)
Thermoresistance input type : PT-100, PT-1000 (IEC751) (ITS 90)
Accuracy : ± 1 % of full scale for thermoresistance
Cold Junction Compensation : Automatically ± 0.1°C / ± 1°C
Sensor Break Protection : Upscale
Sampling Cycle : 3 samples per second
Control Form : ON / OFF
Relay Output : 16(8) A@250 V V for Resistive load ( Output)

(Electrical life : 100.000 switching at full load)

Optional SSR Drive Output : Maximum 20mA, Maximum 17V
Display : 14 mm Red 4 digits LED Display
LED : S (Green), P (Green), C (Yellow), F(Yellow),

Compressor Output (Red), Heating Output (Red)
Internal Buzzer : ³83dB

Approvals :

: 115
: 24
: 24

Mounting. Panel cut-out is 71x29mm.

with none condensing humidity.

o o o o

V ±

230V ( %15) 50/60Hz - 1.5VA

V ±

V ( %15) 50/60Hz - 1.5VA

V ±

V ( %15) 50/60Hz - 1.5VA

W ±

V ( %15) 50/60Hz - 1.5VA

VZ 1.5W

Z

o o

,

Compressor

13

8.Ordering Information

00 00

U

V W Z/

/

800°C/1472°F
999°C/1830°F

400°C/752°F

99.9°C/212°F
400°C/752°F

99.9°C/212°F
150°C/302°F
100°C/212°F

ESM-3710-N

(77x35 DIN Sizes)

Supply VoltageA

24VW ( %15) 50/60Hz - 1.5VA ±

2

24V ( %15) 50/60Hz - 1.5VAV ±

3

115V ( %15) 50/60Hz - 1.5VAV ±

4

230V ( %15) 50/60Hz - 1.5VAV ±

5

10 - 30 V Z

8

Input Type

BC

J ,Fe CuNi IEC584.1(ITS90)

05

K ,NiCr Ni IEC584.1(ITS90)

10

PT 100, IEC751(ITS90)

11

PT 100, IEC751(ITS90

09

PT 1000, IEC751(ITS90)

14

PT 1000, IEC751(ITS90

13

PTC (Not-1)

12

NTC (Not-1)

18

Compressor Output

E

Relay Output (16(8) A@250 V V,at resistive Load, 1 NO,1NC )

1

SSR Driver Output (Maximum 20m, Maximum 17VZ )

2

Relay Output (30(15)A@240 V V,at resistive Load, 1 NO)

3

(Only valid for NTC Input Type devices)

Temp. Sensor which is given with ESM-3710-N

V

0

None

PTC-M6L40.K1.5 (PTC Air Probe 1.5 mt Silicon Cable)

1

PTCS-M6L30.K1.5.1/8” (PTC Liquid Probe 1.5 mt Silicon Cable)

2

NTC-M5L20.K1.5 (NTC Sensor, thermoplastic moulded with 1.5 m cable for cooling application)

3

NTC-M6L50.K1.5 ( NTC Sensor, stainless steel housing with 1.5 m cable for cooling application)

4

Customer

All order information of ESM-3710-N Temperature Controller are given on the table at above. User may
form appropriate device configuration from information and codes that at the table and convert it to the
ordering codes.Firstly, supply voltage then other specifications must be determined. Please fill the order
code blanks according to your needs.
Please contact us, if your needs are out of the standards.

Note-1:If input type is selected PTC or NTC (BC= 12, 18), Temperature sensor is given with the
device.For this reason, if input type is selected as PTC,sensor type (V = 0,1 or 2) or if input type is
selected as NTC, sensor type (V = 0,3 or 4) must be declared in ordering information.

c
c

9

Because of limited mechanical life of relay output contact, SSRoutput is recommended which
the device use PID control algoritm. The device with ON/OFF control algoritm, hysteresis
parameter must be set a suitable value for your system, to avoid too much relay switching.

Before commissioning the device, parameters must be set in accordance with desired use.
Incomplete or incorrect configuration can cause dangerous stiuations.

A BC D E FG HI /

0 1 0 0

/

Scale(°C)

0°C/32°F ;
0°C/32°F ;

-50°C/-58°F ;

-19.9°C/-4°F ;

-50°C/-58°F ;

-19.9°C/-4°F ;

-50°C/-58°F ;

-50°C/-58°F ;

14

9.Optional Accessories

Because of limited mechanical life of relay output contact,
SSRoutput is recommended which the device use PID control algoritm.
The device with ON/OFF control algoritm, hysteresis parameter must be set a suitable value

c

for your system, to avoid too much relay switching.
Before commissioning the device, parameters must be set in accordance with desired use.

Incomplete or incorrect configuration can cause dangerous stiuations.

c

1.RS-485 Module 2.PROKEY Programming Module

c

V Ş Vac,

RS-485 Communication Interface

Z Ş Vdc

Ş Vdc or Vac

W

can be applied

The device is programmed(Upload or
Download) by using the parameters.

Your Technology Partner

Thank you very much for your preference to
use Emko Elektronik products, please visit our
web page to download detailed user manual.

www.emkoelektronik.com.tr

15

16

ESM-3710-N Digitaler

EIN/AUS-Temperaturregler

DIN-Größe 77 x 35

– 4-stelliges Display
– NTC-Eingang oder

PTC-Eingang oder
Thermoelement-Eingang Typ J oder
Thermoelement-Eingang Typ K oder
2-adriger PT-100-Eingang oder
2-adriger PT-1000-Eingang
(Muss in der Bestellung angegeben werden.)

– Einstellbarer Temperatur-Offset EIN/AUS-Temperaturregelung
Auswählbare
Heiz- oder Kühlfunktion
– Auswahl des Betriebs mit Hysterese
– Einstellbarer Temperatur-Offset
– Sollwertunter- und -obergrenzen
– Auswahl des Kompressorbetriebs: durchgängiger Betrieb, Stop

ESM-3710-N Temperaturregler DIN Größe 77x35

oder intermittierender Betrieb bei einem Sensordefekt
– Kompressorschutzverzögerungen
– Einstellbarer interner Summer abhängig vom Sensordefekt-Status.
– Passwortschutz für den Programmierabschnitt
– Installationsparameter unter Verwendung von Prokey
– Fernzugriff, Datenerfassung und Regelung mit Modbus RTU
– Mit CE-Zeichen gemäß europäischen Normen

Bedienungshandbuch. GER ESM-3710-N 01 V07 11/18

DEUTSCH

1. Vorwort

Temperaturregler der Baureihe ESM-3710-N sind auf die Temperaturmessung und -regelung
ausgelegt. Mit ihrer Ein/Aus-Regelungsfunktion, Heiz- und Kühlfunktionen und
benutzerfreundlichen Eigenschaften können sie in zahlreichen Anwendungen eingesetzt
werden. Nachfolgend sind einige Anwendungsbereiche aufgelistet, für die sie geeignet sind:

Anwendungsbereiche Anwendungen

Glas Heizung
Lebensmittel Backöfen
Kunststoff Brutschränke
Petrochemie Lager
Textil, Automation Klimaanlagen
Maschinenproduktion Industrie Usw.

1.1 Umgebungssollwerte

Betriebstemperatur : -20 bis 70 °C

Max. Betriebsfeuchte : 90 % RF (nicht kondensierend)

Höhe : Bis zu 2000 m.

Unzulässige Bedingungen:
Korrosive Atmosphäre

c

Explosive Atmosphäre
Anwendungen im Wohnbereich (Das Gerät ist nur für industrielle
Anwendungen vorgesehen)

1.2 Allgemeine Spezifikationen

Standard

230V ( %15) 50/60HzV ±

Optionale
Versorgungsspannung

V

115 V (±%15) 50/60Hz,

V

24 V (±%15) 50/60Hz,

W

24 V (±%15) 50/60Hz,

- 30 V Z

10

NTC, PTC,
J order K Typ TC
2-adriges PT-100
2-adriges PT-1000

ESM-3710-N

Stromversorgung
Eingang

Temperatursensor
Eingang

Standard

Ausgang-1
(Relaisausgang)

Optional

Ausgang-1

(SSR-Antriebsausgang)

Steuerausgang
Alarmausgang

Steuerausgang
Alarmausgang

Hei- oder Kühlfunktion
EIN/AUS-Betrieb

2

1.3 Installation

Vor der Installation dieses Produkts wird eine Sichtprüfung auf etwaige beim Transport
verursachte Schäden empfohlen. Sie müssen sicherstellen, dass dieses Produkt von
qualifizierten Elektrikern und Mechanikern installiert wird.
Falls bei einem Ausfall oder Defekt dieser Einheit die Gefahr eines ernsthaften Unfalls
besteht, schalten Sie das System aus und trennen den Stromanschluss des Geräts vom
System.
Die Einheit wird normalerweise ohne Netzschalter und Sicherung ausgeliefert. Verwenden
Sie bei Bedarf einen Netzschalter und eine Sicherung.
Achten Sie darauf, die Auslegungsspannung für die Stromversorgung zu verwenden, um
das Gerät vor Schäden zu schützen und Ausfälle zu vermeiden.
Schalten Sie den Strom erst ein, wenn die gesamte Verdrahtung abgeschlossen ist, sodass
ein Stromschlag und Probleme mit dem Gerät vermieden werden können.
Versuchen Sie auf keinen Fall, dieses Gerät zu zerlegen, zu ändern oder zu reparieren. Eine
Manipulation des Geräts führt zu Fehlfunktion, Stromschlag oder Brand.
Setzen Sie das Gerät nicht in feuergefährlichen oder explosiven gasförmigen Atmosphären
ein.
Wenn Sie die Ausrüstung bei der mechanischen Installation in die Öffnung in der
Metallplatte einsetzen, können Metallgrate Verletzungen an den Händen verursachen. Sie
müssen vorsichtig sein.
Die Montage des Produkts an einem System muss unter Verwendung der zugehörigen
Befestigungsklammern erfolgen. Führen Sie die Montage des Geräts nicht mit ungeeigneten
Befestigungsklammern durch. Achten Sie darauf, dass das Gerät während der Montage
nicht zu Boden fällt.
Sie sind dafür verantwortlich, dass dieses Gerät nicht auf eine Weise verwendet wird, die
nicht in diesem Anweisungshandbuch angegeben ist.

1.4 Garantie

EMKO Elektronik garantiert, dass die Ausrüstung frei von Material- und
Herstellungsschäden ist. Diese Garantie gilt für einen Zeitraum von zwei Jahren. Der
Garantiezeitraum beginnt mit dem Lieferdatum. Diese Garantie gilt, solange der Kunde alle
im Garantiedokument und im Betriebshandbuch angegebenen Verpflichtungen und
Verantwortlichkeiten einhält.

1.5 Wartung

Reparaturen dürfen ausschließlich von geschultem und spezialisiertem Personal
durchgeführt werden. Trennen Sie die Stromversorgung zu dem Gerät, bevor Sie auf interne
Bauteile zugreifen.
Reinigen Sie das Gehäuse nicht mit auf Kohlenwasserstoff basierenden Lösungsmitteln
(Benzin, Trichloräthylen usw.). Durch den Einsatz dieser Lösungsmittel kann die
mechanische Zuverlässigkeit des Geräts beeinträchtigt werden. Verwenden Sie ein mit
Ethylalkohol oder Wasser befeuchtetes Tuch, um das äußere Kunststoffgehäuse zu
reinigen.

1.6 Herstellerunternehmen

Herstellerinformationen
Informationen zum Reparatur- und Wartungsservice:

Emko Elektronik Sanayi ve Ticaret A.Ş.
Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA/TURKEY
Telefon: [phone]
Fax : [phone]
Emko Elektronik Sanayi ve Ticaret A.Ş.
Demirtaş Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA /TURKEY
Telefon: [phone]
Fax : [phone]

3

2. Allgemeine Beschreibung

Frontplatte
IP65-Schutz
NEMA 4X

Schaltschrankoberfläche
(max. Dicke 15 mm / 0,59")

Montageklammer

2.1 Vorderansicht und Abmessungen des Temperaturreglers ESM-3710-N

Maximum 15 mm / 0.59 inch

O

C

ESM3710-N

O

S

P

F

SET

P

ü

34,5 mm / 1.36 inch

76 mm / 3 inch

2.2 Einbauausschnitt

29 mm / 1.14 inch

6 mm / 0.24 inch

110 mm / 4.33 inch (min)

71 mm / 2.79 inch

65 mm / 2.56 inch

50 mm / 1.97 inch (min)

4