Efd ValveMate 7060RA Operating Manual

ValveMate

™

7060RA Controller

Operating Manual

Electronic pdf files of EFD®manuals are also available at www.efd-inc.com/manuals.html

USA: 800-556-3484 or [phone]
Europe: 0800 585733 or [phone]
Asia: [phone]
[e-mail] www.efd-inc.com

®

A NORDSON COMPANY

VALVEMATE

7060RA

M

M

M

A NORDSON COMPANY

Introduction and Specifications ..................................3

Operating Features ..................................................4-5

Controller Setup........................................................6-7

Adjusting the Spray ..................................................8-9

Input / Output Connections..................................10-11

Connecting More than One 7060RA Controller ........12

Troubleshooting Guide ..............................................13

Schematic and Replacement Parts List ....................14

Warranty ......................................................back cover

Contents

3 / Introduction and Specifications

The ValveMate7060RA provides nozzle air and drive motor on/off control
for the 782RA spray valve. The controller incorporates unique microprocessor
circuitry to provide exact time control and interact with the host computer.
A built-in air-pressure regulator provides LVLP (low volume low pressure)
nozzle air to ensure high transfer efficiency without overspray. The
ValveMate 7060RA is simple to use and will operate many millions of
cycles without maintenance.

Introduction

Specifications

Size: 19 x 14 x 7 cm (7.5” W x 5.6” D x 2.7” H)

Weight: 1.5 kg (3.3 lb)

Cabinet: Aluminum

Input Voltage: Selectable 100/120/220 VAC

Output circuit fuses: 5 x 20 mm cartridge fuses 315mA

Feedback Circuits: 5 to 24 VDC NC solid-state switch 250mA maximum

Initiate Circuit: 5 to 24 VDC momentary or dry contact closure

Air Input: 70 psi (4.8 bar)

Cycle Rate: Exceeds 400 per minute

Time Range: .001 to 99.9 seconds

Note: Specifications and technical

details are subject to engineering
changes without prior notification.

4 / Operating Features

1. Cycle / Test

Press to initiate one complete dis­pense cycle. Press again to interrupt
a timed cycle. Press and hold while
in the time override mode for continu­ous cycle. Release to stop.

2. Time override

Press to override timed deposit
mode. Display will show (---). While
in this mode, dispensing is manual
using the cycle button, voltage
initiate source or foot pedal (optional,
#2015A).

3. Time / Pressure and PSI / BAR toggle

Press to change digital display from
valve open-time to atomizing air pres­sure. Press and hold for three sec­onds to toggle between psi and bar.

Operating Features

VALVEMATE

7060RA

M

M

Atomizing

air regulator

123

546

Power
switch

M

®

A NORDSON COMPANY

5 / Operating Features

Operating Features

4. Program

Press to clear display to zeros. Display
flashes bright/dim while in program
mode. Press cycle button and hold
until proper amount is sprayed. Total
spray time will be displayed. Press
program button again to lock in
spray time.

5. Time set

Press to change time setting up or
down. Press and release to single step.

6. Motor control mode switch

Switch from OFF to continuous
ON for most applications or to
intermittent ON for low cycle use.

7. Foot pedal connector

If using the optional foot pedal, press
the pedal momentarily to initiate the
controller. To interrupt a timed dispense
cycle, press the pedal again.

220

7

Air input
quick-coupler
70 psi (4.8 bar)
minimum input
pressure

Valve
operating
air outlet
(white)

Atomizing
air outlet
(black)

Air
exhaust

I/O interface

terminal strip

Input power

cord receptacle

(see page 7)

Fuse 125 mA
100V 120V 220V
50/60Hz 20/17VA

1. Initiate +

2. Initiate -

3. Output +

4. Output -

5-24 VDC or
Contact Closure

5-24 VDC
250 mA

]
]

+- - -++-+

123456 87

Outlet B

Outlet A

Air Input
70 PSI
(4.8 bar)

Foot Pedal

5. Alarm +

6. Alarm -

7. Control Valve +

8. Control Valve -

5-24 VDC
250 mA

]

M

M

M