Eaton Electrical PXES4P User Manual
Corporate Headquarters
Eaton Electrical, Inc.
1000 Cherrington Parkway
Moon Township, PA 15108
Phone: 1.800.525.2000
Website: http://www.eatonelectrical.com
Power Xpert Ethernet Switch
PXES4P Series
Installation and
User Guide
PXES4P Switches Installation and User Guide (10/06)
PXES4P Series Switches
Installation and User Guide
Trademarks
Ethernet is a trademark of Xerox Corporation
NEBS is a registered trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories
Copyright © 2006 EATON. All rights reserved. No part of this publication may be
reproduced without prior written permission from EATON, Inc.
Printed in the United States of America.
Important: The PXES4P, 10/100 Mb/s Convenient Switches contain no user
serviceable parts. Attempted service by unauthorized personnel shall render all
warranties null and void. If problems are experienced with PXES4P 10/100
Mb/s Convenient Switches, consult Section 5, troubleshooting, of this User
Guide.
1
PXES4P Switches Installation and User Guide (10/06)
Federal Communications Commission
Radio Frequency Interference Statement
This equipment generates, uses and can radiate frequency energy and if not
installed and used properly, that is in strict accordance with the manufacturer's
instructions, may cause interference to radio communication. It has been tested and
found to comply with the limits for a Class A computing device in accordance with the
specifications in Subpart J of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference, in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
2
PXES4P Switches Installation and User Guide (10/06)
Contacting EATON
EATON ELECTRICAL, INC
For Technical Support please call
800-809-2772
Or
414-449-7100
Or visit our Website
http://www.eatonelectrical.com
3
PXES4P Switches Installation and User Guide (10/06)
TABLE OF CONTENTS Page
1.0 SPECIFICATIONS ............................................................................... 7
1.1 Technical Specifications..................................................................... 7
2.0 INTRODUCTION ............................................................................... 14
2.1 Inspecting the Package and the Product............................................. 14
2.2 Product Description ........................................................................... 16
2.3 PXES4P Series, with four (RJ-45) Copper ports...............................18
2.4 Frame Buffering and Latency............................................................ 20
2.5 Features and Benefits......................................................................... 22
2.6 Applications.......................................................................................24
For PXES4P Series........................................................................................ 24
3.0 INSTALLATION.................................................................................26
3.1 Locating the Convenient Switch Unit................................................ 26
3.2 PXESTRAY for Rack Mounting of PXES4P Series Switches........ 28
3.4 DIN-Rail mounting option................................................................. 29
3.5 Power Requirements, Power Supply Types for PXES4P Series
Switches.........................................................................................................30
4
PXES4P Switches Installation and User Guide (10/06)
3.6 Powering the PXES4PH with 12V, 24V or –48VDC power input... 31
3.7 PXES4P, DC-powered, -48VDC, 24VDC and 12VDC Installation.33
3.8 Connecting Twisted Pair (RJ-45 ports).............................................. 35
3.8.1 Connecting Twisted Pair (RJ-45, CAT 3 or CAT 5, Unshielded
or shielded…………..………….……………………………………
36
3.8.2 Connections to NICs which support Auto-Negotiation, RJ-45 ports. 37
4.0 OPERATION....................................................................................... 38
4.1 Dual-Speed Functionality, and Switching The PXES4P Series
Switches provide four switched ports(three ports in the front and one on the
rear). The architecture supports a dual speed switching environment, with
auto-negotiation capability. ........................................................................... 38
4.2 Auto-cross (MDIX), Auto-negotiation and Speed-sensing................ 40
4.3: Dual LEDs, Front-panel and side-panel ( PXES4P Series )............ 41
5.0 Troubleshooting
5.1 Before Calling for Assistance............................................................ 44
5.2 When Calling for Assistance ............................................................. 45
5
PXES4P Switches Installation and User Guide (10/06)
5.3 Return Material Authorization (RMA) Procedure............................. 46
5.4 Shipping and Packaging Information................................................. 47
Appendix A: Warranty Information……………………………………………
6
PXES4P Switches Installation and User Guide (10/06)
1.0 SPECIFICATIONS
1.1 Technical Specifications
Ports Performance
When a port is operating at 100Mbps:
Data Rate: 100Mbps
When a port is operating at 10 Mbps:
Data Rate: 10 Mbps
Network Standards
100Mb: Ethernet IEEE 802.3u, 100BASE-TX, IEEE 802.1p
10 Mb: Ethernet IEEE 802.3, 10BASE-T
Power Over Ethernet: IEEE 802.3af (PPXES4PP model only)
Auto-sensing for speed: IEEE 802.3u
Data packets that have the 4-bytes tagged VLAN field (802.1q) inserted in
them are received and transmitted unchanged.
7
PXES4P Switches Installation and User Guide (10/06)
Packet-Processing Between Domains
Filter / Forwarding Rate from 100Mbps ports: 148,800 pps max
Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max.
Processing type: Store and Forward, non-blocking
Auto-learning: 2K address table
Address buffer age-out time: 300 sec.
Packet buffers memory: 128KB,dynamically shared on all domains
(Non-blocking switching)
Latency (not including packet time): 100 to 10 Mbps: 5μs
10 to 100Mbps: 5μs
Path Delay Value: 50 BT on all ports
Maximum Ethernet Segment (or Domain) Lengths
10BASE-T (Unshielded twisted pair) - 100 m (328 ft)
100BASE-TX (CAT 5 UTP) - 100 m (328 ft)
Operating Environment
Ambient Temperature : -13ºF to 140ºF (-25ºC to 60ºC)
8
PXES4P Switches Installation and User Guide (10/06)
Long term per independent agency tests (UL): -40ºF to 167ºF (-40ºC to 75ºC)
Storage Temperature: -40ºF to 185ºF (-40ºC to 85ºC)
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude : -200 to 5000ft. (-60 – 15,000 m)
Conformal Coating (optional) Humidity protection
Note: This model is designed for NEBS compliance, including, vibration, shock and
altitude.
Packaging:
Enclosure: Robust sheet metal (Steel).
Dimensions, Switch unit: Height x Width x Depth
PXES4P Hardened: 3.5 in H x 3.0 in W x 1.0 in D (8.9 cm x 7.6 cm x 2.5 cm)
Weight: 4.6 oz. (130g);
Power supply, –d, and i: 5.9 oz (170g)
–Hd, and Hi: 5.8 oz (165g)
–Pd, and =Pi: 7.9 oz (225g)
9
PXES4P Switches Installation and User Guide (10/06)
Cooling Method: The case is used as a heat sink on this model.
POWER SUPPLY :
These products are intended to be supplied by a Listed, Direct Plug-In power unit, marked
“Class 2”, or a Listed ITE Power Supply, marked “LPS”, which has suitably rated output
voltage (i.e. 9vdc, 12vdc, 24vdc, 48vdc), and suitably rated output current (i.e. 100mA to
500mA).When connected to a 48 V centralized dc source these products shall be provided
with a Listed 5 A DC fuse in the supply circuit.
UL listed class II Power Supply, ( AC External):
Power input (8-15)V DC, jack is 2.5mm center +ve , with 6ft. cord
Input: 120vac at 60 Hz for “d” models, 240vac at 50Hz for “i” models that have IEC320
power connector built-in the PS unit. Out put- 12vdc, 1 Amps
Input: 100-240V AC at 47-63Hz, for “-Hd” high temp., 100-240V AC at 47-63Hz “-for
Hi” models that have IEC320 power connector built-in the PS unit.
Out put- 12vdc, 1.25 Amps
10
PXES4P Switches Installation and User Guide (10/06)
Input: 100-240V AC at 47-63Hz, for “-Pd” high temp. 100-240V AC at 47-63Hz, “-Pi”
models that have IEC320 power connector built-in the PS unit.
Out put- 12vdc, 2 Amps
DC to unit: 12V DC, 2.5mm jack, center +ve, 6ft. cord
Power Supply ( Direct DC ): built-in screw terminal
block for +, -, ground. The 12V DC jack is also
present.
12V DC internal (range of 8.0 to 15V DC),
24V DC internal (range of 18 to 36V DC)
-48V DC internal (range of 36 to 60V DC) t.
Power Consumption: 3 watts typical, 4 watts max.
Note 1: 8-15V DC can be used for dual source DC input
11
PXES4P Switches Installation and User Guide (10/06)
Note 2: Internal DC power floats, user may ground “+” or “-” if desired.
Port Connectors:
RJ-45 Port: Auto-cross(MDIX), 100BASE-TX and 10BASE-T:shielded 8-pin
female. Three RJ-45 ports provided in front, and one on the rear. Supports shielded
LED Indicators (Dual- front and end, port #4 has front only)
(STP) and unshielded (UTP) Cat 3, 4, 5 cable.
POWER: Steady ON when power applied (PXES4P model)
10/100: = 100Mbps; OFF = 10 Mbps
LK/ACT: Steady ON for LINK with no traffic, blinking indicates port
is transmitting / receiving.
F/H: ON = full-duplex, OFF = half-duplex
Mounting option for PXES4P Family of Switches:
12
PXES4P Switches Installation and User Guide (10/06)
Metal Mounting clips for panel mounting : included
DIN-Rail mounting option: Model :#PXESDINRL
Rack-mount option: #PXESTRAY
Mean Tine Between Failure (MTBF) – 15+ years, Telcordia (Bellcore SR-332) Method
Agency Approvals and Standard Compliance:
UL Listed (UL 60950), cUL, CE, Emissions meet FCC Part 15, Class A.
NEBS L3 and ETSI compliant
IEEE P1613 Env. Std for Electric Power Substations
IEC61850 EMC and Operating Conditions Class C for Power Substations
Designed for above-the-ceiling (plenum) installation
Made in USA
13
PXES4P Switches Installation and User Guide (10/06)
1.2 Summary of model and descriptions:
PXES4P-Hd, Hi = Hardened, four 10/100 RJ-45 ports Switch, Factory floor, Int. 8-15VDC,
PXES4P-12VDC = Same as PXES4P model, except Ext. AC Hardened power supply not included
PXES4P24C = Same as PXES4P-12VDC model, except for 24VDC power input
PXES4PR-24VDC = Same as PXES4P-24VDC model, but includes PXESDINRL option.
PXES4P-48VDC = Same as PXES4P-24VDC model, except for -48VDC power input.
PXESTRAY = 19” Rack-mount tray for 14-series Switch models, up to 16 units
PXESDINRL = Metal DIN-Rail mounting bracket for one PXES4P Series
2.0 INTRODUCTION
This section describes PXES4P Series models, including appearance, features and
typical applications.
2.1 Inspecting the Package and the Product
Examine the shipping container for obvious damage prior to installing this
product; notify the carrier immediately of any damage which you believe occurred during
Ext. AC Hardened power supply included .
14
PXES4P Switches Installation and User Guide (10/06)
shipment or delivery. Inspect the contents of this package for any signs of damage and
ensure that the items listed below are included.
This package should contain:
1 PXES4P Series Switch Unit
1 External Power Supply (d, i model only)
1 set Metal panel mounting clips and screws, 2 each
1 User Guide, i.e., this manual
(continued next page)
15
Loading...