Dual XDMR6850 User Manual
XDMR6850
INSTALLATION/OWNER’S MANUAL
XM Ready Multimedia Receiver with Detach Face
An optional XM Satellite Radio Receiver may be connected to the XDMR6850.
XM subscription is required for reception. For more information, visit XM’s website
at www.xmradio.com or call 1-877-XM-RADIO. Not available in Alaska or Hawaii.
XDMR6850 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit,
• Remove 2 transit screws located
on top of the unit.
• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening, bending tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.
• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
• Mount the iplug™ adapter to any
smooth clean surface using the
supplied double-sided tape or #2 x
3/8” Phillips head screws.
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
2
XDMR6850 INSTALLATION
Wiring Diagram
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDMR6850 uses one
10 amp ATM fuse located
beside the wiring connector.
3
XDMR6850 OPERATION
Control Locations - Receiver
1 2
20
19 18
Tune/Track Down
1
Power/Eject
2
Volume/Audio/Setup
3
AS/PS/Enter/Function
4
Tune/Track Up
5
Infrared Sensor
6
*Key #0/Preset #10
7
Preset #5/Folder Up
8
9
*Key/Preset #9/EQ
10
Preset #4/Folder Down
63
5
4
15
16
17
*Key/Preset #8/Tuner Scan
11
Preset #3/Intro
12
*Key/Preset #7/Return
13
Preset #2/Random
14
Preset #6/Menu
15
Preset #1/Repeat
16
Mode/Shift/Search
17
Display
18
19
Record
Band/Play/Pause/Scroll
20
71112 89101314
An optional XM Satellite Radio Receiver may be connected to the XDMR6850.
XM subscription is required for reception. For more information, visit XM’s website at
www.xmradio.com or call 1-877-XM-RADIO. Not available in Alaska or Hawaii.
*Function keys 7, 8, 9 and 0 apply to XM Radio and MP3/WMA operation only.
4
XDMR6850 OPERATION
Control Locations - Remote
1
2
3
19
18
17
16
15
14
13
Power/Eject
1
Volume Up
2
AS/PS/Enter/Function
3
Audio/Setup
4
Tune/Track Up
5
*Key #0/Preset #10
6
Volume Down
7
Preset #3/Intro
8
Preset #2/Random
9
Preset #6/Menu
10
4
5
6
7
8
9
10
11
12
*Key/Preset #9/EQ
11
*Key/Preset #8/Tuner Scan
12
*Key/Preset #7/Return
13
Preset #5/Folder Up
14
Preset #4/Folder Down
15
Preset #1/Repeat
16
17
Mode/Search/Shift
18
Tune/Track Down
19
Band/Play/Pause/Scroll
5
XDMR6850 OPERATION
General Operation
Front Panel Note:
Front Panel Removal
Power On/Off
Mode
Volume
Shift Function
(XM Radio only)
Preset EQ Curves
The front panel is semi-permanently attached during
assembly. Please refer to the separate yellow instructions
(before installation) to make the front panel removable.
With the unit off, press EJECT to allow the front panel to slide
down. Gently squeeze the release tab located on the bottom
center underside and pull front panel down and away from
unit to remove. To install, insert left side first, then push right
side to secure.
Press PWR for 2 seconds or any other button momentarily
to turn the unit on. Inserting a disc will turn the unit on
automatically. Press PWR for 2 seconds to turn the unit off.
Press MODE to select between AM/FM, *XM Radio, CD
player and auxiliary input. Modes of operation are indicated
in the display. *Optional XM Satellite Radio Receiver and
subscription required for XM Radio operation.
Adjust volume using rotary encoder (00-46).
Press SHIFT for 2 seconds to activate the SHIFT function.
The SHIFT icon will appear in the display. In XM Radio mode,
the SHIFT function must be active to access the EQ function.
Press SHIFT again for 2 seconds to cancel.
Press EQ to select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
Display
Set the Clock
6
When in AM/FM, CD or AUX mode:
Press DISP to select between clock and radio frequency
(tuner mode), clock and CD elapsed time/track (CD mode), or
clock and AUX (AUX mode).
When in XM Radio mode:
Press DISP to select between channel name, artist name,
song title or clock.
With the unit on, press and hold DISP until the clock begins to
flash, then release. Press TUNE
TUNE
save the selected time.
to adjust the minutes. Press DISP momentarily to
ll
to adjust the hours and
nn
XDMR6850 OPERATION
General Operation - Setup Menu
12/24-hour Clock
Setup Menu
Menu Function Options Action
Loudness Curve
Clock Display
Priority
Tuner Frequency
Spacing
Clock Display
Auxiliary Mode
Beep
Confirmation
Local/Distance
Tuning
LOUD OFF Disables the loudness function.
LOUD ON Enables the loudness function. Activating this feature
FUNC PRI Radio frequency (tuner mode), XM information (XM
CLK PRI Clock will be displayed by default. Radio frequency
FREQ USA Programs the unit to USA tuner spacing.
FREQ EUR Programs the unit to European tuner spacing.
CLK OFF Programs the unit to not display the clock when the
CLK ON Programs the unit to display the clock when the power
AUX ON Enables access to auxiliary mode.
AUX OFF Disables access to auxiliary mode.
BEEP OFF Disables the confirmation beep.
BEEP ON Enables the confirmation beep.
LOC OFF Activates Distance tuning.
LOC ON Activates Local tuning for strong station reception only.
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Press and hold the rotary encoder for more than 3 seconds
to access the setup menu. Press the rotary encoder
momentarily to select between the menu functions and
rotate the rotary encoder left/right to adjust or activate the
desired function.
will enhance the bass and treble frequencies when
listening to music at low volumes.
mode), CD elapsed time/track or MP3/WMA file
information (CD mode) or AUX (AUX mode) will be
displayed by default. Clock is accessed by pressing
DISP
momentarily.
(tuner mode), XM information (XM mode), CD elapsed
time/track or MP3/WMA file information (CD mode) is
accessed by pressing DISP momentarily.
(200kHz for FM and 10kHz for AM)
(50kHz for FM and 9kHz for AM)
power is off.
is off.
7
XDMR6850 OPERATION
BASSVOLUME
TREBLE BALANCE F
ADER
General Operation
Audio
Bass
Treble
Balance
Fader
Source Audio Memory
Press rotary encoder momentarily to select between
Volume (default), Bass, Treble, Balance, & Fader.
Press rotary encoder until BAS appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press rotary encoder until TRE appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press rotary encoder until BAL appears then rotate encoder
left/right to adjust (BAL L 12-BAL 00-BAL R 12).
BAL 00 represents equal balance
Press rotary encoder until FAD appears then rotate encoder
left/right to adjust (FAD F 12-FAD 00-FAD R 12).
FAD 00 represents equal fader
Individual Bass and Treble settings are retained in memory
for AM, FM, CD, XM, and AUX modes. This allows you to
save the Bass and Treble settings separately for each mode.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
Reset
Record
Menu
Return
8
Press RESET upon initial installation or if abnormal
operation occurs. The reset button is located behind the
faceplate.
This feature is available when used with the EAUSB20
Media Link Adapter (sold separately).
This feature is available when used with the EAUSB20
Media Link Adapter (sold separately).
This feature is available when used with the EAUSB20
Media Link Adapter (sold separately).
Loading...