Dual XDMP680 User Manual

XDMP680
INSTALLATION/OWNER'S MANUAL
AM/FM/CD/MP3/WMA Receiver with Detach Face
XDMP680 INSTALLATION
Preparation
Please read entire manual before installation.
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove 2 transit screws located on top of the unit.
• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
• Install mounting sleeve into opening, bending tabs to secure.
• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
• Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
• Test for correct operation and slide into mounting sleeve to secure.
• Snap trim ring into place.
• Mount the iplug™ adapter to any
smooth clean surface using the supplied double-sided tape or #2 x 3/8” Phillips head screws.
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
2
XDMP680 INSTALLATION
Wiring Diagram
FUSE
When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDMP680 uses one 10 amp ATM fuse located beside the wiring connector.
3
XDMP680 OPERATION
Control Locations
1 2
3
4 5
6
2122 20 19 18 17 16 15 14 13 12 11
Release
1
Power
2
Volume
3
Band/Play/Pause
4
Mode/Search
5
Auto Store/Preset Scan/Enter
6
Tune/Track Down
7
Eject
8
9
Tune/Track Up
10
Display/0
11
EQ/9
Tuner Scan/8
12
Local/Distance/Return/7
13
Preset 6/Folder Up
14
Preset 5/Folder Down
15
Preset 4/Menu
16
Preset 3/Intro
17
Preset 2/Random
18
Preset 1/Repeat
19
20
Audio
21
Loudness
22
Record
7
8 9 10
The XDMP680 allows playback of your favorite MP3 and WMA files recorded on CD-R and CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track search - even while a song is currently playing!
4
XDMP680 OPERATION
General Operation
Faceplate Removal
Semi-permanent 
Faceplate Installation
Power On/Off
Mode
Loudness 
Volume
Programmable 
Turn-On Volume
Preset EQ Curves
Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure.
Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate.
Press POWER or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press POWER to turn the unit off.
Press MODE to select between tuner, CD player and auxiliary input. Modes of operation are indicated in the display.
Press LOUD to activate and deactivate the loudness contour curve. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes.
Adjust volume using rotary encoder (00-46).
Press and hold POWER for 3 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display.
Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected).
Display
Set the Clock
12/24-hour Clock
Press DISP to select between clock and radio frequency (tuner mode), clock and CD track/elapsed time (CD mode), or clock and AUX (AUX mode).
With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE hours and TUNE  momentarily to save the selected time.
The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00).
to adjust the minutes. Press DISP
ll
to adjust the
nn
5
XDMP680 OPERATION
General Operation
Programmable Display 
Priority
Programmable Clock 
Priority
Reset
In tuner mode, press and hold DISP then press TUNE  to select function priority display. “FREQ” will momentarily appear in the display.
Note: "FUNC" will appear in CD or AUX modes. Radio frequency (tuner mode), CD track/elapsed time (CD mode) or AUX (AUX mode) will be displayed by default.
Note: When playing MP3/WMA files, the track number/elapsed time, track name, directory name, title, artist, album, year or comment will be displayed by default. Clock is accessed by pressing DISP momentarily.
Press and hold DISP then press TUNE display priority. “TIME” will momentarily appear in the display. Clock will be displayed by default. Radio frequency, CD track/elapsed time or MP3/WMA file information is accessed by pressing DISP momentarily.
Programs unit to display clock/no clock when unit is off. Press and hold MODE then press PRESET 1 to select clock priority on/off. “CLK ON” or “CLK OFF” will momentarily appear in the display.
Press RESET upon initial installation or if abnormal operation occurs. The reset button is located behind the faceplate.
to select time
nn
ll
Confirmation Beep
Record
Menu
Return
6
Press and hold AUDIO for 3 seconds to turn confirmation beep on/off.
This feature is available when used with the EAUSB20 Media Link Adapter (sold separately).
This feature is available when used with the EAUSB20 Media Link Adapter (sold separately).
This feature is available when used with the EAUSB20 Media Link Adapter (sold separately).
+ 14 hidden pages