Turn off the phone and disconnect the charger before removing
the battery cover.
Installing the SIM card and battery
The SIM card holder is located behind the battery.
Remove the battery cover and the battery if it is already
1.
installed.
Insert the SIM card by carefully sliding it into the holder.
2.
Make sure that the SIM card’s gold contacts are facing
inward and that the cut-off corner is pointing upward. Take
care not to scratch or bend the contacts on the SIM card.
Insert the battery by sliding it into the battery compartment
3.
with the contacts facing upward to the right.
Replace the battery cover.
4.
3
English
Charging
Warning!
Only use batteries, charger and accessories that have been
approved for use with this particular model. Connecting
other accessories may be dangerous and may invalidate the
phone’s type approval and guarantee.
When the battery is running low, is displayed and a warning
signal is heard. To charge the battery, connect the AC power
adapter to a wall socket and to the charging socket
is displayed briey when the charger is connected to the
phone, and when it is disconnected. The battery charge
indicator will be animated while charging.
It takes approximately 3 hours to fully charge the battery.
is displayed on the screen when charging is completed.
Note!
Full battery capacity will not be reached until the battery has
been charged 3–4 times.
y
.
The temperature must be in the range 32°–104°F when
charging.
Batteries degrade over time, which means that call time and
standby time will normally decrease with regular use.
4
English
Operation
Activating the phone
Press and hold 1 on the top of the phone for a few seconds to
turn it on/off. It takes several seconds so keep holding until you
hear the sound.
The following messages may be displayed:
SIM card missing or
incorrectly inserted.
SIM card damaged or not
valid.
If the SIM card is valid but protected with a PIN code (Personal
Identication Number), PIN: is displayed.
Enter the PIN code and press OK ( upper left corner of
keypad).
Delete with Clear ( upper right corner of keypad).
Trials : # shows the number of PIN attempts left. When no more
attempts remain, SIM blocked is displayed. The SIM card must
now be unlocked with the PUK code (Personal Unblocking Key).
Enter the PUK code and conrm with OK.
1.
Enter a new PIN code and conrm with OK.
2.
Note!
If PIN and PUK codes were not provided with your SIM card,
please contact your network operator.
Changing the language, time and date
These are all set for you. The menu language will default to
English. See Settings on how to change language, time and date.
The date and time are automatically set to the local time for the
area you are in when the phone is powered on.
5
English
Making a call
Enter the phone number. Skip backwards with Clear.
1.
2.
3.
Press
Press
q
to dial. Press Cancel to cancel dialing.
L
to end the call.
Note!
There is no dial tone. Simply have the phone turned on and it
is ready for use.
Note!
When making international calls, press * twice for the
international prex "+". Always use ”+” before the country
code (instead of 00 or similar) for best operation.
Making a call from the Phonebook
Press Name to open the Phonebook.
1.
Use the arrow keys / to scroll through the
2.
Phonebook, or quick search by pressing the key
corresponding to the rst letter of the entry, see Text input.
Press Call to dial the selected entry, or press Back to return
3.
to standby mode.
Receiving a call
Press
1.
signal and then Reject to reject the call (busy signal).
Alternately, press
Press
2.
See also Call options.
q
to answer, or press Silent to switch off the ring
L
L
to end the call.
to reject the call directly.
Volume control
Use the side keys +/– to adjust the sound volume. The volume
level is indicated on the display.
6
English
Display Symbols
Signal strengthMissed call
Ring onlyKeylock on
Vib & ringBluetooth on
Vib onlyBluetooth connected
Light onlyBattery level
Alarm activeNew message
Headset connected
SIM card missingCharger connected
SIM card errorCharger disconnected
MuteHeadset connected
Unlocking keypadHeadset disconnected
New SMS messageHandsfree on
SOS calls onlyHandsfree off
OK (conrmed)Warning
QueryError
Battery level lowCharging (animated)
CallingCall ended
Incoming callMissed call
SearchingCall on-hold
7
English
Additional Functions
Call options
During a call, the soft keys1 give access to additional functions:
Options (left soft key)
A menu with the following options is displayed:
Hold single call
End single call
New call
Phonebook
Msg center
Mute
Put the current call on hold
End the current call (same as
Call another number (three-party call)
Search the Phonebook
Write or read SMS messages
Disable the microphone (mute)
L
)
SPK on (right soft key)
Activates handsfree mode, which allows you to speak without
holding the phone.
Speak clearly into the microphone at a maximum distance of 3 feet
(1 meter). Use the side keys +/– to adjust the loudspeaker volume.
Press SPK off to return to normal mode.
Note!
The handsfree function allows only one person at a time
to talk. Switching between talk/listen is triggered by the
sound of the person talking. Loud noises (music, etc.) in the
background may interfere with the handsfree function.
Call waiting
An alert tone will be heard if there is an incoming call while talking.
To put the current call on hold and answer the incoming call, press
Options.
This service must be activated, see Settings/Call setup.
1 The Soft keys have multiple functions. The current key
function is shown above the soft key on the display.
8
English
Call information
During a call, the called or calling phone number and the elapsed
call time is displayed.
If the identity of the caller is withheld, Unknown is displayed.
Call log
Answered, missed, and outgoing calls are saved in a combined call
log. 20 calls of each type can be stored in the log. For multiple calls
related to the same number, only the most recent call is saved.
Retrieving and dialing
Press
1.
Use the arrow keys / to scroll through the call list.
2.
Press
3.
for the following settings:
q
with no numbers entered on the screen.
= Incoming call
= Outgoing call
= Missed call
q
to dial the highlighted number or press Options
View
Delete
Delete all
Save
Create new
Update
Show details for the selected call
Delete the call
Delete all calls in the call log
Save the number in the Phonebook
Creates new contact in the Phonebook
Update an existent contact in the Phonebook
9
English
Phonebook
The Phonebook can store 100 entries with 3 phone numbers in
each entry.
Creating a Phonebook entry
Press Menu, scroll to and press OK.
1.
Select -New contact- and press Add.
2.
Select Name and press Edit.
3.
Enter a name for the contact, see Text input. Delete with Clear.
4.
Note! Each time you press a key you will scroll through
the three letter options. Once the letter you would like is
highlighted, pause for a moment and it will be selected. You
can then begin pressing a key to select the next letter.
Press Done.
5.
Select Mobile, Home number or Ofce number, and
6.
enter the phone number, then press Save.
Press Back (repeatedly) to return to standby mode.
7.
Note!
For international phone numbers, always use ”+” before the
country code (instead of 00 or similar) for best operation.
Managing Phonebook entries
Press Menu, scroll to and press OK.
1.
Select an entry and press Options.
2.
Select one of the following options and press OK.
3.
View
Show details for the selected contact.
Edit
Edit the name/number. To edit the name, you rst need to
1.
press Edit. Use the side keys +/– to move the cursor.
Delete with Clear.
Press Save.
2.
10
English
Add new contact
See Creating a Phonebook entry.
Call
Press OK to call the contact.
Send SMS
Press OK to write an SMS message, see SMS messaging.
Delete
Press OK to delete the selected Phonebook entry. Press Yes to
conrm or No to abort.
Delete all
Select From SIM or From Phone and press OK to delete all
Phonebook entries from the SIM card or phone memory.
Enter the phone code and press OK to conrm.
Copy all
Select From SIM and press OK to copy all Phonebook entries
from the SIM card to the phone memory. Press Yes to conrm or
No to abort.
Select From Phone and press OK to copy all Phonebook entries
from the phone memory to the SIM card. Press Yes to conrm or
No to abort.
Storage
Select SIM or Phone and press OK to select the default storage
for new Phonebook entries.
Send vCard
Select Send by SMS and press OK to send the selected
Phonebook entry as a vCard via SMS. Enter the phone number of
the recipient and press OK to send.
Select Send Bluetooth and press OK to send the selected
Phonebook entry as a vCard via Bluetooth. See Settings/Bluetooth
on how to connect with Bluetooth.
11
English
Key lock
Press and hold * to lock/unlock the keypad.
Incoming calls can be answered by pressing
keypad is locked. During the call, the keypad is unlocked. When
the call is ended or rejected, the keypad is locked again.
See Settings for key lock options.
q
even if the
Note!
The emergency number 911 can be dialed without unlocking
the keypad.
Silent mode
Silent is a xed prole with SMS and ring signals disabled, while
vibration and key tone settings are unchanged. Press and hold #
to activate/deactivate Silent.
See also Settings/User prole (rings & tones).
Flashlight
Press and hold on the left side of the phone to switch the
built-in ashlight on/off.
The ashlight can also be automatically switched off after 20
seconds. See Settings for more options.
Note!
The ashlight will drain the battery very quickly. Remember to
turn off the ashlight after use.
Headset
When a headset is connected, the internal microphone in the
phone is automatically disconnected.
When receiving a call you can use the answer key on the headset
cable (if it has one) to answer and end calls.
Warning!
Using a headset at high volume can damage your hearing.
Adjust the sound volume carefully when using a headset.
12
English
SOS calls
Warning!
Mobile phones such as this unit use radio signals, the
mobile phone network, the terrestrial network and userprogrammed functions. This means that connection cannot
be guaranteed in all circumstances. Therefore, you should
never rely solely on a mobile phone for very important calls
such as medical emergencies.
When the phone is turned on, the right soft key shows SOS
before the SIM card is activated or if the phone lock is on.
Press SOS, then press Yes to automatically call 911. Press No
to return to the activation screen. If you pressed Yes by mistake,
press Cancel immediately to cancel the call.
As long as the phone is switched on, you may also place an SOS
call by entering
911
followed by
q
.
Most – but not all – networks accept calls to 911 without a valid
SIM card. Sometimes an emergency call cannot be placed due to
network, environment or interference issues.
13
English
Emergency Call key
The Emergency Call key allows you easy access to contact a
predetermined group of numbers should you need help. These
numbers will normally be family members or friends. To use the
Emergency Call key, you must rst activated the function and
store in the emergency numbers you wish to call (see Settings on
page 24).
Once activated, to make an emergency call you will follow the
instructions for the option you selected:
Press and hold the Emergency Call key on the back of the
On Normal
phone for 3 seconds.
Or
Press the Emergency Call key two times within 1 second.
On (3)
Press the Emergency Call key three times within 1 second.
After entering the key sequence above, the phone will rst send
a text message to every number in your Emergency Call list.
Then it will attempt to call each number, starting at the top and
continuing through the list until a call is answered. Once a call is
answered (even if by an answering machine) the phone will stop
dialing any additional numbers in the list. If no call is answered,
dialing will repeat 3 times or until
L
is pressed.
Note!
Automatic calls to 911 is normally not allowed. Do not save
this number in the list of numbers to be called automatically.
Some private security companies can accept automatic calls
from their clients. Always contact the security company before
programming in its number. The function is set to interactThe function is set to interact
with most voice mail systems to avoid that the call sequence
is interrupted.
14
English
Text input
Text is entered by pressing the numerical keys repeatedly
to select characters. When writing SMS messages in some
languages you can use the Smart ABC (eZiType™) input method
which uses a dictionary to suggest words. See Settings on how to
change input method.
Entering text
Press the key repeatedly until the desired character is shown.
Wait a few seconds before entering the next character.
Press * for a list of special characters. Select the desired
character and press OK to enter it.
Use the side keys +/– to move the cursor within the text.
Press # to cycle upper case, lower case and numerals.
Entering text with Smart ABC
Press each key once, even if the displayed character is not the
one you want. The dictionary will suggest words based on the
keys you have pressed. Use the arrow keys to select a word, then
press OK and continue with the next word.
If none of the suggested words are correct, press # to change
to manual input mode. The icon on the top left of the display
indicates the input mode:
eZi
eZi
ABC
abc
123
ABC
abc
UPPER CASE with SmartABC
lower case with SmartABC
UPPER CASE
lower case
Numerals
15
English
SMS Messaging
Creating and sending messages
Press Menu, scroll to and press OK.
1.
Select Write message and press OK.
2.
Type your message (see Text input) then press Done.
3.
Select one of the sending options below and press OK to
4.
conrm.
Send only
Save & send
Send to many
Send the message without saving
Send the message and save it in the Outbox
Add more recipients for the message
If Send to many was selected, do the following:
Select Recipients and press OK.
1.
Select one of the empty entries and press Edit.
2.
Enter a phone number or press Search to open the
3.
Phonebook. After entering or selecting a number, press OK.
Repeat step 2–3 to add additional recipients.
4.
When nished, press Done.
Note!
For international phone numbers, always use ”+” before the
country code (instead of 00 or similar) for best operation.
Outgoing messages (Outbox)
Press Menu, scroll to and press OK.
1.
Select Outbox and press OK.
2.
Select a message and press OK. Use the arrow keys to scroll
3.
the message up/down.
Press Options, see Incoming messages (Inbox).
4.
16
English
Incoming messages (Inbox)
Press Menu, scroll to and press OK.
1.
Select Inbox and press OK.
2.
Select a message from the list and press Read. Use the
3.
arrow keys to scroll the message up/down.
Press Options.
4.
Reply
Type your reply, then press Done. The message will be sent
immediately.
Delete
Press Yes to delete the message, or No to return to the menu.
Edit
Edit the message, then press Done to show the sending options
(see Creating and sending messages).
Forward (Inbox)(Inbox)
Shows the sending options.
Delete all
Press Yes to delete all messages in the Inbox. Press No to return
to the menu.
Use number
Displays all phone numbers contained in the message as well as
the number of the sender.
Use the arrow keys to select one of the displayed numbers.
1.
Press Options.
2.
Select one of the following options and press OK.
3.
Call
Save
Create new
Update
Send SMS
Call the selected number
Save the number in the Phonebook
Creates new contact in the Phonebook
Update an existent contact in the Phonebook
Write a new SMS message
17
English
Settings
Note!
The settings described in this chapter are carried out in
standby mode.
Time and date
Setting the time and date
Press Menu, scroll to and press OK.
1.
Select Time & date and press OK.
2.
Select Set time and press OK.
3.
Enter the time (HH:MM), then press OK.
4.
Select am or pm and press OK.
5.
Select Set date and press OK.
6.
Enter the date (YYYY/MM/DD), then press OK.
7.
Setting the time/date format
Press Menu, scroll to and press OK.
1.
Select Time & date and press OK.
2.
Select Set format and press OK.
3.
Select Time Format and press OK.
4.
Select 12 hours or 24 hours and press OK.
5.
Select Date Format and press OK.
6.
Select the desired date format and press OK.
7.
Setting Auto day/time on/off
Press Menu, scroll to and press OK.
1.
Select Time & date and press OK.
2.
Select Auto day/time and press OK.
3.
Select On/Off and press OK.
4.
18
English
User setup
Wallpaper
You can select from 8 different display backgrounds.
Press Menu, scroll to and press OK.
1.
Select User setup and press OK.
2.
Select Wallpaper and press OK.
3.
Scroll up/down to display the available wallpapers.
4.
Press OK to conrm or Back to discard changes.
5.
Idle display
In standby mode the display can present date, time, and the
connected network, or just the time.
Press Menu, scroll to and press OK.
1.
Select User setup and press OK.
2.
Select Idle display and press OK.
3.
Select Clock only or All info and press OK.
4.
Owner number
Stores your phone number. Some SIM-cards shows the phone
number as default. If your phone number doesn’t show it, you
can store it manually.
Press Menu, scroll to and press OK.
1.
Select User setup and press OK.
2.
Select Owner number and press OK.
3.
Select Empty and press Options.
4.
Select Edit and press OK.
5.
Press Edit and enter your name, see Text input. Delete with
6.
Clear.
Press Done to conrm.
7.
Press .
8.
Enter your phone number.
9.
Press Save to save the number.
10.
Press Back (repeatedly) to return to standby mode.
11.
19
English
Flashlight settings
Press Menu, scroll to and press OK.
1.
Select User setup and press OK.
2.
Select Flashlight and press OK.
3.
Select one of the following options and press OK.
4.
On
Off
20 sec.
Flashlight key enabled.
Flashlight key disabled.
Flashlight key enabled. Flashlight will turn off automatically
after 20 seconds.
HAC mode (Hearing aid compatibility mode)
User option to select HAC mode.
Press Menu, scroll to and press OK.
1.
Select User setup and press OK.
2.
Select HAC mode and press OK.
3.
Select On/Off and press OK.
4.
Language
The default language for the phone menus, messages, etc. is
English. You can change this to any other language supported by
the phone.
Press Menu, scroll to and press OK.
1.
Select User setup and press OK.
2.
Select Language and press OK.
3.
Scroll up/down to select a language, then press OK.
4.
LCD backlight
Sets the delay time before the display backlight is turned off.
Press Menu, scroll to and press OK.
1.
Select User setup and press OK.
2.
Select LCD backlight and press OK.
3.
Select 15 sec. or 30 sec. and press OK.
4.
20
English
User prole (rings & tones)
The phone has 4 available user proles. Each prole can have
different settings for ring signals, ring volume, etc.
Silent is a xed prole with SMS and ring signals disabled, while
vibration and key tone settings are unchanged.
Press and hold # to activate/deactivate Silent.
Selecting a user prole
Press Menu, scroll to and press OK.
1.
Select User proles and press OK.
2.
Select a user prole and press Options.
3.
Select Activate and press OK.
4.
Tone setup
Press Menu, scroll to and press OK.
1.
Select User proles and press OK.
2.
Select a user prole and press Options.
3.
Select Customize and press OK.
4.
Select Tone setup and press OK.
5.
Select Ring tone and press OK.
6.
Select one of the available tones, the tone will be played.
7.
Press OK to conrm, or press Back to discard changes.
Set up the Alarm, Message tone and Keypad tone in the same
8.
way.
21
English
Tone volume
Press Menu, scroll to and press OK.
1.
Select User proles and press OK.
2.
Select a user prole and press Options.
3.
Select Customize and press OK.
4.
Select Volume and press OK.
5.
Scroll up/down to change the ring volume, then press OK.
6.
Set up the key tone volume in the same way.
7.
Alert type (ring/vibrate)
Incoming calls can be signaled by a ring tone and/or vibration, or
by light only.
Press Menu, scroll to and press OK.
1.
Select User proles and press OK.
2.
Select a user prole and press Options.
3.
Select Customize and press OK.
4.
Select Alert type and press OK.
5.
Select the desired signaling mode and press OK.
6.
Warning and error tones
Warning and error tones are used to alert the user of low battery
power, phone and SIM card errors, etc.
Press Menu, scroll to and press OK.
1.
Select User proles and press OK.
2.
Select a user prole and press Options.
3.
Select Customize and press OK.
4.
Select Extra tone and press OK.
5.
Select a tone and press On/Off to enable/disable it.
6.
Press Done to save.
7.
22
English
Bluetooth settings
You can connect wirelessly to other Bluetooth®-compatible
devices such as headsets.
Press Menu, scroll to and press OK.
1.
2.
Select Bluetooth and press OK for the following settings:
Search device
Lists saved devices and enables you to add new devices. Select
the device from the list and press Options.
Search new
Connect
Disconnect
Select
Rename
Delete
Delete all
Search new Bluetooth device
Connect the selected device. Select the required
prole, usually the Headset.
Disconnect the selected device.
Select the connected device.
Change the name of the device.
Delete the device from the list.
Delete all devices from the list.
Function on/off
Select On/Off and press OK to enable/disable Bluetooth.
Visibility
Select On/Off to make your phone visible/invisible to other
Bluetooth devices.
Device name
Enter the name your phone should appear with for other
Bluetooth devices and press Done.
Blocking functions
You can disable some functions to simplify use of the phone.
Press Menu, scroll to and press OK.
1.
Select Block functions and press OK.
2.
Select each function you want to disable and press On.
3.
Press Done to conrm.
4.
23
English
Emergency
Settings for the Emergency Call key function.
See also Operation/Emergency call on page 14.
Press Menu, scroll to and press OK.
1.
Select Emergency and press OK for the following settings:
2.
Activation
Select one of the following options and press OK.
Note,
We suggest using On (3) to avoid accidental calls to your
Emergency Call numbers.)
To activate, press and hold key for >3 seconds, or press 2
times within 1 second.
Emergency Call key enabled.
To activate, press key 3 times within 1 second.
Numbers list
The list of numbers that will be called when the Emergency
Call key is pressed. To add a new emergency number, select
Numbers List, then press Add. Enter the information. Repeat
until you have max. 5 emergency numbers. See Phonebook page
10 to learn on how to add names/numbers. To edit or delete an
existing entry, select desired entry and press Options.
Message
The SMS text message to be sent when the Emergency Call key is
pressed. Press Edit to enter/edit text, then press OK to save.
Important Emergency Key information
Please read this important safety information before enabling the
Emergency Call function:
Be careful about including numbers with automatic answering
in the call list. Once a call is answered the phone will stop
placing calls to other numbers in your call list.
24
English
Voice mail
Press Menu, scroll to and press OK.
1.
Select Voice mail and press OK, then Options.
2.
Select Connect and press OK to call the voice mailbox.
3.
The voice mailbox can also be called by pressing and holding 1.
If no number has been added yet, the line will show Empty.
Adding or editing the voice mailbox number
Press Menu, scroll to and press OK.
1.
Select Voice mail and press OK.
2.
Press Options.
3.
Select Edit and press OK.
4.
Press Edit and enter the name and then press Done.
5.
Press .
6.
Enter the phone number to your voice mailbox.
7.
Press Save to save the number.
8.
Note!
The voice mailbox number is provided by your network operator.
Speed dial
The numerical keys 0 and 2–9 can be used for speed dialing.
Adding speed dial numbers
Press Menu, scroll to and press OK.
1.
Select Speed dial and press OK.
2.
Select 0 and press Add.
3.
Select an entry from the Phonebook and press OK.
4.
Repeat to add speed dial entries for keys 2–9.
5.
To speed dial an entry, press and hold the corresponding number
key.
To edit an existing entry, select it and press Options, then select
Edit or Delete and press OK.
25
English
Call setup
Press Menu, scroll to and press OK.
1.
Select Call setup and press OK for the following settings:
2.
Caller ID
Controls display of your phone number on the recipient’s phone.
Select an option and press OK.
Set by network
Hide ID
Send ID
Use default setting by the network
Never show your number
Always show your number
Call waiting
Select an option and press OK. See also Operation - Call waiting.
Activate
Deactivate
Query status
Enables the function
Disables the function
Displays if the service is active or not
Call divert
Set up which calls should be diverted.
Select a condition and press OK, then select Activate,
Deactivate or Query status (see Call waiting above) for each.
Div. voice calls
Div. unreach
Div. no reply
Diverts all voice calls.
Diverts incoming calls if the phone is turned off or
out of range.
Diverts incoming calls if unanswered.
Divert if busy
Cancel diverts
Diverts incoming calls if the line is busy.
Do not divert calls
26
English
Call barring
The phone can be restricted to disallow certain types of calls.
Note!
To change these settings a password is needed. Contact your
network operator to get the password.
Outgoing calls
All calls
Internat. calls
Int. except home
Incoming calls
All calls
When roaming
Cancel all
Set barr. PW
Press OK then select:
User can answer incoming calls but not dial out.
User cannot call international numbers.
User cannot call international numbers except to the
country associated with the SIM card.
Press OK then select:
User can dial out but not receive incoming calls.
User cannot receive incoming calls while roaming
(operating in other networks).
Cancel all call barring (password needed)
Change the barring password (password needed)
Answer mode
Answer incoming calls by pressing any key.
Select Any key and press OK.
Select On/Off and press OK to enable/disable this function.
27
Loading...
+ 70 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.