D-Link DPH-70s installation Guide

Updated on 7 July 2005

D-Link

DPH-70s Modem Phone (SIP)

Quick Setup guide

DPH-70s Modem Phone

1) Connecting the Devices
Using telephone cable (RJ-11), connect the LINE port of the DPH-70 to the

telephone wall jack. Plug the AC power adapter, lift the handset and listen for
dial tone this indicates that the DPH-70 has been installed properly.

2) Configuring the DPH-70s phone using phone keypad

The DPH-70 voice menu helps you through the configuration process.
Step 1: Pick up handset or press speaker button
Step 2: Press ‘*123*’ and followed by “#”

Step 3: Enter the password (Default password is ‘12345’) and followed by “#”

2.1 ISP Parameters or ISP Dial up Account

Step 1: Enter “1” to edit the ISP Parameters
Step 2: At ISP Phone Number, press “1”, enter the ISP Phone Number
and followed by “#” button. During entry, the phone will echo the
character pressed
Step 3: Press “1” to accept
Step 4: At ISP User Name, press “1”, enter the ISP User Name and
followed by “#” button. During entry, the phone will echo the
character pressed
Step 5: Press “1” to accept”
Step 6: At ISP Password, press “1”, enter the ISP Password and
followed by “#” button
Step 7: Press “1” to accept
Step 8: Follow the voice menu, enter “5” to save the ISP information

Note: Please refer to the Keypad Legend for more details

2.2 Calling Card Parameters

Step 1: Enter “2” to edit the Calling Card Parameters
Step 2: At Calling Card User ID, press “1”, enter 12-digit MediaRing
account number, and followed by “#” button. During entry, the
phone will echo the character pressed
Step 3: Press “1” to exit
Step 4: At Calling Card Password, press “1”, enter 6-digit PIN and
followed by “#” button. During entry, the phone will echo the
character pressed
Step 5: Press “1” to accept
Step 6: At VoIP Server Address, enter the SIP Proxy,
“mrsip001.mediaring.com”*, including dots
Step 7: Press “1” to accept
Step 8: Follow the voice menu, enter “5” to save the ISP information

Note: Please refer to the Keypad Legend for more details

3) How to make on-net call in RECEIVE state

Step 1: Pick up the handset

Step 2: Press the DIAL UP button
Step 3: Dial the “country code” + area code (if any)” + destination
Number. Phone will play the progress tone and blink the DIAL
UP LED. It will stays connected to the Internet for 15 minutes

Note: Please refer to the Keypad Legend for more details

4) How to make on-net call in special dialing
Step 1: Pick up the handset
Step 2: Dial the “country code” + “area code (if any)” + destination
Number and followed by “#” button

Note: Please refer to the Keypad Legend for more details

5) How to make off-net call

Step 1: Press speaker button

Step 2: Press the DIAL UP button
Step 2: Dial the “country code” + “area code (if any)” + destination
number and followed by “#” button

Note: Please refer to the Keypad Legend for more details

6) How to make PSTN call

Step 1: Pick up the handset
Step 2: Dial the destination number and followed by “#” button

7) Resetting to factory default

Step 1: Pick up the handset

Step 2: To reset DPH-70, press ‘*789*’ and followed by “#” button

while phone is idle

Step 3: Press “1”, enter the default password, ‘12345’ and followed by “#”

Note: Please refer to the Keypad Legend for more details

Keypad Legend

I Entering (Lower-case) Small Letters

 Press twice to enter the first character of the key
 Press thrice to enter the second character of the key
 Press four times to enter the third character of the key
 Press five times to enter the fourth character of the key

If the key is pressed, more than above-mentioned, it accepts the last letter of the
key.

II Entering (Upper-case) Capital Letters

Press a SHIFT button followed by the digit key.

 Twice to enter the first capital letter of the key
 Thrice to enter the second capital letter of the key
 Four times to enter the third capital letter of the key
 Five times to enter the fourth capital letter of the key

If the key is pressed more than above-mentioned after the SHIFT button is pressed,
it accepts. The last capital letter of the key

III Entering Special Characters

Special

Character

“Backspace” 0

@ “At” 1

. “Dot” 2

- “Hyphen” 3
_ “Underscore” 4
$ “Dollar” 5
& “Ampersand” 6

/ “Slash” 7
: “Colon” 8

IV Configuration Menu

Description DIAL UP followed

by: