D-Link DIR-300 G User Manual
2D-Link DIR-300 User Manual
Table of Contents
Package Contents ................................................................................. 4
System Requirements
................................................................. 4
Introduction
...................................................................................5
Features
............................................................................................ 6
Hardware Overview
.....................................................................7
Connections
...........................................................................7
LEDs
........................................................................................... 8
Installation .............................................................................................. 9
Before you Begin
........................................................................... 9
Wireless Installation Considerations
....................................10
Connect to Cable/DSL/Satellite Modem
............................11
Connect to Another Router
....................................................12
Conguration
.......................................................................................14
Web-based Conguration Utility
..........................................14
Setup Wizard
........................................................................15
Internet Setup
......................................................................19
Dynamic (Cable)
.............................................................19
PPPoE (DSL)
......................................................................20
PPTP
....................................................................................21
L2TP
....................................................................................22
Big Pond
............................................................................23
Static (assigned by ISP)
................................................24
Wireless Setup
......................................................................25
LAN Setup
..............................................................................31
DHCP Server Settings
........................................................32
Time and Date
......................................................................33
Parental Control
..................................................................34
Port Forwarding
..................................................................35
Application Rules
................................................................36
Access Control
.....................................................................37
Firewall & DMZ
.....................................................................38
Advanced Wireless
.............................................................39
Advanced Network
............................................................40
Routing
...................................................................................41
Administrator Login Name:
........................................42
Administrator Password:
.............................................42
Enable Remote Management:
..................................42
Device Administration
......................................................42
Save and Restore
.................................................................43
Firmware Update
................................................................44
DDNS Setting
.......................................................................45
System Check
.......................................................................46
Schedules
..............................................................................47
Log Settings
..........................................................................48
Device Info
............................................................................49
Log
...........................................................................................50
Table of Contents
3D-Link DIR-300 User Manual
Table of Contents
Statistics .................................................................................51
Active Session
.....................................................................51
Wireless
..................................................................................52
Help
.........................................................................................53
Wireless Security
.................................................................................54
What is WEP?
................................................................................54
Congure WEP
.............................................................................55
What is WPA?
................................................................................56
Congure WPA-PSK and WPA2-PSK
.....................................57
Congure WPA/WPA2-PSK
......................................................58
Congure WPA, WPA2, and WPA/WPA2 (RADIUS)
...........59
Connect to a Wireless Network .....................................................60
Using Windows
®
XP ....................................................................60
Congure WEP
.............................................................................61
Congure WPA-PSK
....................................................................63
Setting Up Wi-Fi Protection
............................................................65
(WCN 2.0 in Windows Vista)
............................................................65
Initial Router Conguration for Wi-Fi Protection
.............65
Setting Up a Congured Router
............................................66
Changing the Computer Name and Joining a Workgroup .67
Conguring the IP Address in Vista
..............................................69
Setting Up a Connection or Network Wirelessly .....................72
Connecting to a Secured Wireless Network (WEP, WPA-PSK &
WPA2-PSK)
............................................................................................77
Connecting to an Unsecured Wireless Network
.....................81
Troubleshooting
.................................................................................85
Wireless Basics .....................................................................................89
What is Wireless?
.........................................................................90
Tips
...................................................................................................92
Wireless Modes
............................................................................93
Networking Basics
..............................................................................94
Check your IP address
...............................................................94
Statically Assign an IP address
...............................................95
Technical Specications
...................................................................96
Contacting Technical Support .......................................................98
Warranty
................................................................................................99
Registration ....................................................................................... 104
4D-Link DIR-300 User Manual
Section 1 - Product Overview
• D-Link DIR-300 Wireless Router
• Power Adapter
• Ethernet Cable
• Manual and Warranty on CD
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet
adapter
• Internet Explorer Version 6.0 or Netscape Navigator™ Version 6.0 and above (for conguration)
Package Contents
Note: Using a power supply with a different voltage rating than the one included with
the DIR-300 will cause damage and void the warranty for this product.
Note: Always attach the power cord plug to the power supply, before inserting the
power cord and connected power supply to the wall outlet.
5D-Link DIR-300 User Manual
Section 1 - Product Overview
Introduction
D-Link, the industry leader in wireless networking, introduces another breakthrough in wireless connectivity. The
D-Link Wireless G DIR-300 Router which is capable of transferring data with a maximum wireless signal rate of up to 54Mbps* in
the 2.4GHz frequency — the same wireless frequency as 802.11b. The D-Link DIR-300 Wireless Router also offers four Ethernet
ports to support multiple computers.
The advanced wireless technology built into the DIR-300 Wireless Router offers data transfer speeds with a maximum wireless
signal rate of up to 54Mbps* through its wireless channels allowing streaming videos and other high bandwidth applications, such
as online gaming events, to operate without the hassle of Ethernet cables. The ability to use high bandwidth applications also makes
streaming real-time programs more enjoyable and more efcient.
With the DIR-300 Wireless Router’s built-in advanced rewall, threats of hackers penetrating your network are minimized. Some
rewall features include functions that allow or disallow certain ports to be open for certain applications. Time scheduling can be
established as a rewall rule so that specic ports will be open at certain times and be closed at other times. Features like content
ltering, MAC ltering, URL blocking, and domain blocking are useful tools to prevent other unwanted intruders from connecting
to your network or browsing restricted sites.
The easy-to-use conguration wizard takes only minutes to setup and guides users step-by-step through conguring the DIR-
300. With all the versatile features and an user-friendly utility, the DIR-300 Wireless Router provides an enhanced networking
experience.
* Maximum wireless signal rate derived from IEEE Standard 802.11g specications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network trafc, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will
adversely affect wireless signal range.
6D-Link DIR-300 User Manual
Section 1 - Product Overview
• Faster Wireless Networking - The DIR-300 provides up to 54Mbps* wireless connection with other 802.11g
wireless clients. This capability allows users to participate in real-time activities online, such as video streaming,
online gaming, and real-time audio. The performance of this 802.11g wireless router gives you the freedom of
wireless networking at speeds 5x faster than 802.11b.
• Compatible with 802.11b and 802.11g Devices - The DIR-300 is still fully compatible with the IEEE 802.11b
standard, so it can connect with existing 802.11b PCI, USB and Cardbus adapters.
• Advanced Firewall Features - The Web-based user interface displays a number of advanced network management
features including:
• Content Filtering - Easily applied content ltering based on MAC Address, URL, and/or Domain
Name.
• Filter Scheduling - These lters can be scheduled to be active on certain days or for a duration of
hours or minutes.
• Secure Multiple/Concurrent Sessions - The DIR-300 can pass through VPN sessions. It supports
multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-300 can securely access
corporate networks.
• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-300 lets you control
what information is accessible to those on the wireless network, whether from the Internet or from your company’s
server. Congure your router to your specic settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11g specications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network trafc, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will
adversely affect wireless signal range.
Features
7D-Link DIR-300 User Manual
Section 1 - Product Overview
Hardware Overview
Connections
Pressing the Reset Button restores the
router to its original factory default
settings.
Receptor for the Power Adapter.
The Auto MDI/MDIX WAN
port is the connection for the
Ethernet cable to the Cable or
DSL modem.
LAN Ports
Connect Ethernet devices such as
computers, switches, and hubs.
8D-Link DIR-300 User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
WAN LED
A solid light indicates connection on the
WAN port. This LED blinks during data
transmission.
WLAN LED
A solid light indicates that the wireless segment
is ready. This LED blinks during wireless data
transmission.
Local Network LEDs
A solid light indicates a connection to an Ethernetenabled computer on ports 1-4. This LED blinks
during data transmission.
Status LED
A blinking light indicates that the
DIR-300 is ready.
Power LED
A solid light indicates a proper
connection to the power supply.
9D-Link DIR-300 User Manual
Section 2 - Installation
Before you Begin
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the router in
an enclosed area such as a closet, cabinet, or in the attic or garage.
Please congure the router with the computer that was last connected directly to your modem. Also, you can only use the Ethernet
port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect
the USB cable and connect an Ethernet cable to the WAN port on the router, and then turn the modem back on. In some cases, you
may need to call your ISP to change connection types (USB to Ethernet).
If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump,
or Ethernet 300 from your computer or you will not be able to connect to the Internet.
10D-Link DIR-300 User Manual
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating
range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects
that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and
background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic
guidelines:
1.
Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each
wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the
number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters)
thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for
better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range.
Try to position access points, wireless routers, and computers so that the signal passes through drywall or open
doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le
cabinets, brick, and concrete will degrade your wireless signal.
4.
Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF
noise.
5.
If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security
systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone
base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in
use.
11D-Link DIR-300 User Manual
Section 2 - Installation
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your
computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the WAN port
on the router.
4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your
computer.
5.
Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router to boot.
7. Turn on your computer.
8.
Verify the link lights on the router. The power light, WAN light, and the LAN light (the port that your computer is plugged
into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable connections are
correct.
9. Skip to page 14 to congure your router.
Connect to Cable/DSL/Satellite Modem
12D-Link DIR-300 User Manual
Section 2 - Installation
If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the
following before connecting the router to your network:
• Disable UPnP
™
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept
a DHCP address from your other router.
To connect to another router, please follow the steps below:
1.
Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your
IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking Basics section for
more information. If you need to change the settings, write down your existing settings before making any changes. In most
cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to
your computer.
2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to admin
and leave the password box empty. Click OK to continue.
3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings to
continue.
4.
Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save Settings to
continue.
5.
Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your
settings. Use this new IP address to access the conguration utility of the router in the future. Close the browser and change
your computer’s IP settings back to the original values as in Step 1.
Connect to Another Router
13D-Link DIR-300 User Manual
Section 2 - Installation
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into
the WAN port of the D-Link router.
8. You may now use the other three LAN ports to connect other Ethernet devices and computers. To congure your wireless
network, open a web browser and enter the IP address you assigned to the router. Refer to the Conguration and Wireless
Security sections for more information on setting up your wireless network.
14D-Link DIR-300 User Manual
Section 3 - Conguration
Conguration
This section will show you how to congure your new D-Link wireless router using the web-based conguration utility.
Web-based Conguration Utility
To access the conguration utility, open a web-browser such
as Internet Explorer and enter the IP address of the router
(192.168.0.1).
Enter the user name (admin) and your password. Leave the
password blank by default.
If you get a Page Cannot be Displayed error, please refer
to the Troubleshooting section for assistance.
15D-Link DIR-300 User Manual
Section 3 - Conguration
Setup Wizard
You may run the setup wizard from the opening Internet
Setup window to quickly set up your router. Click Internet
Connection Setup Wizard, you will be directed to the
rst window of the wizard.
Click Next to continue.
Create a new password and then click Next to continue.
16D-Link DIR-300 User Manual
Section 3 - Conguration
Select your time zone from the drop-down menu and then click Next to
continue.
Select the type of Internet connection you use and then click Next to
continue.
If you selected Dynamic, you may need to enter the MAC address of the computer
that was last connected directly to your modem. If you are currently using
that computer, click Clone Your PC’s MAC Address and then click Next to
continue.
The Host Name is optional but may be required by some ISPs. The default host
name is the device name of the Router and may be changed.
17D-Link DIR-300 User Manual
Section 3 - Conguration
If you selected PPPoE, enter your PPPoE username and password. Click Next to
continue.
Select Static if your ISP assigned you the IP address, subnet mask, gateway, and
DNS server addresses.
Note: Make sure to remove your PPPoE software from your computer. The software
is no longer needed and will not work through a router.
If you selected PPTP, enter your PPTP username and password. Click Next to
continue.
If you selected L2TP, enter your L2TP username and password. Click Next to
continue.
18D-Link DIR-300 User Manual
Section 3 - Conguration
If you selected Static, enter your network settings supplied by your Internet provider.
Click Next to continue.
Click Connect to save your settings.
If you selected Big Pond, enter your Big Pond username and password. Click Next
to continue.
Please allow 1-2 minutes for rebooting. When the router has nished rebooting,
the opening window will be displayed.
19D-Link DIR-300 User Manual
Section 3 - Conguration
Choose Dynamic IP Address to obtain IP Address information
automatically from your ISP. Select this option if your ISP does
not give you any IP numbers to use. This option is commonly
used for Cable modem services.
The Host Name is optional but may be required by some ISPs.
The default host name is the device name of the Router and
may be changed.
The default MAC Address is set to the WAN’s physical interface
MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by
your ISP.
The default MAC address is set to the WAN’s physical interface
MAC address on the Broadband Router. You can use the “Clone
MAC Address” button to copy the MAC address of the Ethernet
Card installed by your ISP and replace the WAN MAC address
with the MAC address of the router. It is not recommended that
you change the default MAC address unless required by your
ISP.
Enter the Primary DNS (Domain Name Server) server IP address assigned by your ISP.
This is optional.
Dynamic IP
Address:
Host Name:
MAC Address:
Internet Setup
Dynamic (Cable)
Clone MAC
Address:
Primary DNS
Addresses:
Secondary DNS:
MTU:
Maximum Transmission Unit - You may need to change the MTU for optimal performance with your specic ISP.
Access Point
Mode:
Checking this box disables NAT and turns the Router into an
Access Point only.
To manually set up the Internet connection, click the Manual Internet Connection Setup button on the Router’s opening
window.
20D-Link DIR-300 User Manual
Section 3 - Conguration
Select Dynamic (most common) or Static. Select Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password
in the next box.
Enter the ISP Service Name (optional).
Enter the IP address (Static PPPoE only).
Enter the Primary and Secondary DNS Server Addresses
(Static PPPoE only).
Enter a maximum idle time during which the Internet
connection is ma i nt a in e d du r i n g i n ac t iv i ty. To
di sable this featu r e, en able Au to-re c onnec t.
Maximum Transmission Unit - You may need to change
the MTU for optimal performance with your specic ISP.
1492 is the default MTU.
Select eith er A lways -on, Manu al, or Connect-o n
demand.
PPPoE:
User Name:
Password:
Service Name:
IP Address:
DNS Addresses:
Maximum Idle
Time:
MTU:
Connection Mode
Select:
Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your
computer. The software is no longer needed and will not work through a router.
21D-Link DIR-300 User Manual
Section 3 - Conguration
Select Dynamic (most common) or Static. Select Static if
your ISP assigned you the IP address, subnet mask, gateway,
and DNS server addresses.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your ISP
(Internet Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your PPTP account name.
Enter your PPTP password and then retype the password in
the next box.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Maximum Transmission Unit - You may need to change the
MTU for optimal performance.
Select either Always-on, Manual, or Connect-on demand.
PPTP:
IP Address:
Subnet Mask:
Gateway:
DNS:
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
Server IP:
PPTP Account:
PPTP Password:
Maximum Idle
Time:
MTU:
Connect Mode:
22D-Link DIR-300 User Manual
Section 3 - Conguration
Select Dynamic (most common) or Static. Select Static if your
ISP assigned you the IP address, subnet mask, gateway, and
DNS server addresses.
Enter the IP address (Static L2TP only).
Enter the Primary and Secondary DNS Server Addresses (Static
L2TP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your ISP (In-
ternet Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your L2TP account name.
Enter your L2TP password and then retype the password in the
next box.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Maximum Transmission Unit - You may need to change the
MTU for optimal performance with your specic ISP.
Select either Always-on, Manual, or Connect-on demand.
L2TP:
IP Address:
Subnet Mask:
Gateway:
DNS:
Server IP:
L2TP Account:
L2TP Password:
Maximum Idle
Time:
MTU:
Connect Mode:
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and
password. This option is typically used for DSL services.
23D-Link DIR-300 User Manual
Section 3 - Conguration
Enter your Big Pond user name.
Enter your Big Pond password and then retype the
password in the next box.
Enter the IP address of the login server.
Enter the IP address of the login server.
The default MAC Address is set to the WAN’s
physical interface MAC address on the Broadband
Router. It is not recommended that you change the
default MAC address unless required by your ISP.
The default MAC address is set to the WAN’s
physical interface MAC address on the Broadband
Router. You can use the “Clone MAC Address”
button to copy the MAC address of the Ethernet
Card installed by your ISP and replace the WAN
MAC address with the MAC address of the router.
It is not recommended that you change the default
MAC address unless required by your ISP.
User Name:
Password:
Auth Server:
Login Server IP:
MAC Address:
Clone MAC
Address:
Internet Setup
Big Pond
Choose Big Pond if your ISP uses a Big Pond connection. Your ISP will provide you with a username and password.
24D-Link DIR-300 User Manual
Section 3 - Conguration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The default MAC Address is set to the WAN’s physical
interface MAC address on the Broadband Router. It is
not recommended that you change the default MAC
address unless required by your ISP.
The default MAC address is set to the WAN’s physical
interface MAC address on the Broadband Router. You
can use the Clone MAC Address button to copy the
MAC address of the Ethernet Card installed by your
ISP and replace the WAN MAC address with the MAC
address of the router. It is not recommended that you
change the default MAC address unless required by
your ISP.
Enter the Primary DNS server IP address assigned by
your ISP.
This is optional.
Maximum Transmission Unit - you may need to change
the MTU for optimal performance with your specic
ISP. 1492 is the default MTU.
IP Address:
Subnet Mask:
ISP Gateway:
MAC Address:
Clone MAC
Address:
Primary DNS
Address:
Secondary DNS
Address:
MTU:
Internet Setup
Static (assigned by ISP)
Select Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway
address, and DNS address(es) provided to you by your ISP. Each IP address entered in the elds must be in the appropriate IP form, which are four
octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
25D-Link DIR-300 User Manual
Section 3 - Conguration
Wireless Setup
Wireless settings for the router may be configured
manually or by using a wizard. To use the wizard, click
the Wireless Connection Setup Wizard button and then
follow the steps that are described below. To congure the
wireless settings manually, click the Manual Wireless
Connection Setup button. The parameters for this window
are described later in this section. The Wireless Security
section that directly follows this Conguration section
provides additional explanation for how to congure the
WEP, WPA, WPA2, and WPA/WPA2 wireless security
mode options.
Click Next to continue.
Enter a Wireless Network Name in the textbox, which is also
know as the SSID, and then click Next to continue.
26D-Link DIR-300 User Manual
Section 3 - Conguration
Use the radio buttons to select the desired level of wireless security, Best,
Better, or Good, and then click Next to continue.
Enter a Wireless Security Password in the textbox and then click Next to
continue.
This window displays a summary of your wireless security settings. Please print this
out or record this information in a safe place and then click Save to continue.
The Router will save your new settings and reboot. When it is nished after 1-2
minutes, the opening Wireless Setup window is displayed.
27D-Link DIR-300 User Manual
Section 3 - Conguration
To implement Wi-Fi protection, or WCN 2.0, tick the
Enable checkbox, click either Generate New PIN
or Reset PIN to Default, and then congure the Wi-
Fi settings below. Please see the Setting Up Wi-Fi
Protection (WCN 2.0 in Windows Vista) section later
in this manual for detailed conguration information.
Check the box to enable the wireless function. If you
do not want to use wireless, uncheck the box to disable
all the wireless functions.
Service Set Identier (SSID) is the name of your
wireless network. Create a name using up to 32
characters. The SSID is case-sensitive.
Indicates the channel setting for the DIR-300. By
default the channel is set to 6. The Channel can be
changed to fit the channel setting for an existing
wireless network or to customize the wireless network.
The Auto Channel Selection setting can be selected
to allow the DIR-300 to choose the channel with the
least amount of interference.
Use the drop-down menu to select the appropriate Transmission Rate in Mbits per second. Many users will want to use the default setting,
Best (automatic).
Enable Wi-Fi Multimedia to enjoy basic quality of service features. WMM prioritizes trafc according to four access categories: voice,
video, best effort, and background.
Check this option if you would not like the SSID of your wireless network to be broadcasted by the DIR-300. If this option is checked,
the SSID of the DIR-300 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-300
in order to connect to it.
Wi-Fi Protected
Setup:
Wireless Channel:
Wireless Network
Name:
Transmission
Rate:
WMM Enable:
Enable
Enable Hidden
Wireless:
28D-Link DIR-300 User Manual
Section 3 - Conguration
1. To enable wireless security on the Router, use the drop-
down menu to select the desired option. To enable WEP,
select Enable WEP Wireless Security (basic).
2. Next to Authentication, select either Open or Shared
Key. Shared Key provides greater security.
3. Select either 64Bit or 128Bit encryption from the drop-
down menu next to WEP Encryption.
4. Next to Default Key Type, select WEP Key 1 and enter
a WEP key that you create. Make sure you enter this key
exactly on all your wireless devices. You may enter up
to four different keys either using Hex or ASCII. Hex
is recommended (letters A-F and numbers 0-9 are valid).
In ASCII all numbers and letters are valid.
5. Click Save Settings to save your settings. If you are
conguring the Router with a wireless adapter, you
will lose connectivity until you enable WEP on your
adapter and enter the same WEP key as you did on the
Router.
Security Mode:
NOTE:
It is recommended to enable encryption on your wireless Router before
your wireless network adapters. Please establish wireless connectivity
before enabling encryption. Your wireless signal may degrade when
enabling encryption due to the added overhead.
29D-Link DIR-300 User Manual
Section 3 - Conguration
1. To enable WPA, WPA2, or WPA/WPA2, select either
Enable WPA Only Wireless Security (enhanced), Enable
WPA2 Only Wireless Security (enhanced), or Enable
WPA/WPA2 Wireless Security (enhanced).
2. Next to Cipher Type, select TKIP, AES, or Both.
3. Next to PSK/EAP, select PSK.
4. N e x t t o N e t w o r k K e y , e n t e r a
pa s s ph r a se . Th e ke y is a n a l p h a - n u m e r i c
password between 8 and 63 characters long. The
password can include symbols (!?*&_) and spaces.
Make sure you enter this key exactly the same on all
other wireless clients.
5. Click Save Settings to save your settings. If you are
conguring the router with a wireless adapter, you will
lose connectivity until you enable WPA, WPA2, or
WPA/WPA2 (whichever of the three options you have
selected above) on your adapter and enter the same
network key as you did on the router.
30D-Link DIR-300 User Manual
Section 3 - Conguration
1. To enable WPA, WPA2, or WPA/WPA2 for a RADIUS
server, next to Security Mode, select Enable WPA
Only Wireless Security (enhanced), Enable WPA2 Only
Wireless Security (enhanced), or Enable WPA/WPA2
Wireless Security (enhanced).
2. Next to Cipher Type, select TKIP, AES, or Auto.
3. Next to PSK/EAP, select EAP.
4. Next to RADIUS Server 1 enter the IP Address of
your RADIUS server.
5. Next to Port, enter the port you are using with your
RADIUS server. 1812 is the default port.
6. Next to Shared Secret, enter the security key.
7. If you have a secondary RADIUS server, enter its IP
address, port, and secret key.
8. Click Save Settings to save your settings.
Loading...