D-link DIR-130 User Guide

Table of Contents

Manual Overview

This manual contains the following sections:

Section 1 - “Product Overview” describes what is included with the DIR-130 router, and things to consider before installing.

Section 2 - “Installation” describes how to install the router on your network.

Section 3 - “Conﬁguration” describes how to conﬁgure the settings on your DIR-130 router.

Section 4 - “Troubleshooting” explains how to resolve common issues.

Section 5 - “Appendix” contains networking basics, technical speciﬁcations, technical support information, warranty, GNU general public license, and registration information.

iD-Link DIR-130 User Manual

Table of Contents

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes.

Manual Revisions

Revision Date Description

1.0 Feb. 8, 2007 DIR-130 rev. A1 with ﬁrmware 1.00.

Trademarks

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.

iiD-Link DIR-130 User Manual

Table of Contents

Manual Overview .......................................................... i

Manual Revisions .................................................... ii

Trademarks .............................................................. ii

Product Overview ........................................................1

Package Contents....................................................1

System Requirements ............................................. 1

Features ...................................................................2

Hardware Overview ................................................. 3

Connections .......................................................3

LEDs .................................................................. 4

Installation .................................................................... 5

Before you Begin ..................................................... 5

Connect to Cable/DSL/Satellite Modem .................. 6

Conﬁguration ...............................................................7

Web-based Conﬁguration Utility .............................. 7

Setup Wizard .....................................................8

Manual Conﬁguration .......................................12

Dynamic (Cable)...........................................12

PPPoE (DSL) ...............................................13

PPTP ............................................................ 14

L2TP ............................................................. 15

Big Pond .......................................................16

Static (assigned by ISP) ............................... 17

Network Settings ..............................................18

DHCP Server Settings .................................19

DHCP Reservation ....................................... 20

VPN Settings ...................................................21

IPSec Settings .............................................. 22

PPTP/L2TP Settings ....................................23

Virtual Server ...................................................24

Port Forwarding ...............................................26

Application Rules ............................................. 27

Network Filters .................................................28

Website Filters ................................................. 29

Firewall Settings ...............................................30

DMZ .............................................................30

VPN Passthrough ......................................... 30

Advanced Network Settings .............................31

UPnP ............................................................ 31

WAN Ping Respond .....................................31

WAN Port Speed .......................................... 31

Administrator Settings ......................................32

Change Password ........................................ 32

Remote Management ................................... 32

Time Settings ...................................................33

System Settings ...............................................34

Update Firmware .............................................35

DDNS ...............................................................36

System Check ..................................................37

Schedules ........................................................ 38

Log Settings .....................................................39

Device Information ........................................... 40

iiiD-Link DIR-130 User Manual

Table of Contents

Log ...................................................................41

Stats ................................................................. 42

LAN Computers ...............................................42

VPN .................................................................43

Support ............................................................44

Troubleshooting .........................................................45

Networking Basics .................................................... 49

Check your IP address .......................................... 49

Statically Assign an IP address ............................. 50

Technical Speciﬁcations ........................................... 51

Default Factory Settings ........................................... 52

Contacting Technical Support .................................. 53

Warranty .....................................................................54

GNU/Linux GPL .......................................................... 59

GNU General Public License ................................. 60

Registration ................................................................ 66

ivD-Link DIR-130 User Manual

Section 1 - Product Overview

• D-Link DIR-130 8-Port Broadband Router

• Power Adapter

• CAT5 Ethernet Cable

• CD-ROM with Installation Wizard, User Manual, and Special Offers

Note: Using a power supply with a different voltage rating than the one included with the DIR-130 will cause damage and void the warranty for this product.

Product Overview

Package Contents

System Requirements

• Ethernet-based Cable or DSL Modem

• Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet adapter

• Internet Explorer Version 6.0, Mozilla 1.7.12 (5.0), or Firefox 1.5 and above (for conﬁguration)

• Installation Wizard requires Windows® XP with Service Pack 2

1D-Link DIR-130 User Manual

Section 1 - Product Overview

• Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features including:

• Parental Controls - Easily applied content ﬁltering based on MAC Address, URL, and/or Domain Name.

• Filter Scheduling - These ﬁlters can be scheduled to be active on certain days or for a duration of hours or minutes.

• Secure Multiple/Concurrent Sessions - The DIR-130 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-130 can securely access corporate networks.

Features

• User-friendly Setup Wizard - Through the easy-to-use web-based user interface, the DIR-130 allows you to control what information is accessible to those on the network, whether from the Internet or from your company’s server. Conﬁgure your router to your speciﬁc settings within minutes.

2D-Link DIR-130 User Manual

Section 1 - Product Overview

LAN Ports (1-8) Connect Ethernet devices such as computers, switches, and hubs.

Hardware Overview

Connections

Reset Pressing the Reset button restores the router to its original factory default settings.

* The USB port is currently inactive.

Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem.

Power Receptor

Receptor for the supplied power adapter.

3D-Link DIR-130 User Manual

Section 1 - Product Overview

Status LED

A blinking light indicates that the DIR-130 is ready.

Hardware Overview

LEDs

Local Network LEDs

A solid light indicates a connection to an Ethernet-enabled computer on ports 1-8. This LED blinks during data transmission.

Power LED A solid light indicates a proper connection to the power supply.

Internet LED A solid light indicates connection on the Internet port. This LED blinks during data transmission.

4D-Link DIR-130 User Manual

Section 2 - Installation

Installation

This section will walk you through the installation process.

Before you Begin

Please conﬁgure the router with the computer that was last connected directly to your modem. Also, you can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).

If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.

5D-Link DIR-130 User Manual

Section 2 - Installation

Connect to Cable/DSL/Satellite Modem

If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:

1. Place the router in an open and central location. Do not plug the power adapter into the router.

2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer.

3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router.

4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your computer.

5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).

6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router to boot.

7. Turn on your computer.

8. Verify the link lights on the router. The power light, Internet light, and the LAN light (the port that your computer is plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable connections are correct.

9. Refer to the next page to conﬁgure your router.

6D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Conﬁguration

This section will show you how to conﬁgure your new D-Link router using the web-based conﬁguration utility.

Web-based Conﬁguration Utility

To access the conﬁguration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).

Select Admin from the drop-down menu and then enter your password. Leave the password blank by default.

If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.

7D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Setup Wizard

You may click Setup Wizard to quickly conﬁgure your router.

If you want to enter your settings without running the wizard, click Manual Conﬁgure and skip to page 12.

Click Launch Internet Connection Setup Wizard to begin.

8D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Click Next to continue.

Create a new password and then click Next to continue.

Select your time zone from the drop-down menu and then click Next to continue.

Select the type of Internet connection you use and then click Next to continue.

9D-Link DIR-130 User Manual

Section 3 - Conﬁguration

If you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue.

The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.

If you selected PPPoE, enter your PPPoE username and password. Click Next to continue.

Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.

Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.

If you selected PPTP, enter your PPTP username and password. Click Next to continue.

10D-Link DIR-130 User Manual

Section 3 - Conﬁguration

If you selected L2TP, enter your L2TP username and password. Click Next to continue.

If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue.

If you selected Big Pond, select your authentication server from the drop down menu. You will also need to enter your Big Pond username and password. Click Next to continue.

Click Connect to save your settings. Once the router is ﬁnished rebooting, click Continue. Please allow 1-2 minutes to connect.

Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet.

11D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Manual Conﬁguration

Dynamic (Cable)

My Internet

Connection:

Host Name:

MAC Address:

DNS Addresses:

Select Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services.

The Host Name is optional but may be required by some ISPs.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

Enter the Primary and Secondary DNS server IP address(es) assigned by your ISP.

MTU:

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1500 is the default MTU.

12D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Internet Setup

PPPoE (DSL)

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.

My Internet

Connection:

Address Mode:

User Name:

Password:

Service Name:

IP Address:

MAC Address:

DNS Addresses:

Select PPPoE (Username/Password) from the drop-down menu.

Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.

Enter your PPPoE user name.

Enter your PPPoE password and then retype the password in the next box.

Enter the ISP Service Name (optional).

Enter the IP address (Static PPPoE only).

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).

Maximum Idle Time:

MTU:

Connect Mode:

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1492 is the default MTU.

Select either Always-on, On-Demand, or Manual.

13D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Internet Setup

PPTP

Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.

Address Mode:

IP Address:

Subnet Mask:

Gateway:

DNS:

Server IP/Name:

PPTP Account:

PPTP Password:

Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.

Enter the IP address (Static PPTP only).

Enter the Primary and Secondary DNS Server Addresses (Static PPTP only).

Enter the Gateway IP Address provided by your ISP.

The DNS server information will be supplied by your ISP (Internet Service Provider.)

Enter the Server IP provided by your ISP (optional).

Enter your PPTP account (username).

Enter your PPTP password and then retype the password in the next box.

Maximum Idle

Time:

MTU:

Connect Mode:

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Autoreconnect.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1400 is the default MTU.

Select either Always-on, On-Demand, or Manual.

14D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Internet Setup

L2TP

Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.

Address Mode:

IP Address:

Subnet Mask:

Gateway:

DNS:

Server IP/Name:

L2TP Account:

L2TP Password:

Maximum Idle Time:

Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.

Enter the L2TP IP address supplied by your ISP (Static only).

Enter the Subnet Mask supplied by your ISP (Static only).

Enter the Gateway IP Address provided by your ISP.

Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).

Enter the Server IP provided by your ISP (optional).

Enter your L2TP account (username).

Enter your L2TP password and then retype the password in the next box.

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.

MTU:

Connect Mode:

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1400 is the default MTU.

Select either Always-on, On-Demand, or Manual.

15D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Internet Setup

Big Pond

My Internet

Connection:

Username:

Password:

Auth Server:

MAC Address:

Select BigPond (Australia) from the drop-down menu.

Enter your BigPond username.

Enter your BigPond password and then retype the password in the next box.

Select the type of authentication server being used from the drop-down menu.

Enter the IP address of the login server.

The default MAC Address is set to the Internet’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

16D-Link DIR-130 User Manual

Section 3 - Conﬁguration

Internet Setup

Static (assigned by ISP)

Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the ﬁelds must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.

IP Address:

Subnet Mask:

ISP Gateway:

MAC Address:

DNS Servers:

MTU:

Enter the IP address assigned by your ISP.

Enter the Subnet Mask assigned by your ISP.

Enter the Gateway assigned by your ISP.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

The DNS server information will be supplied by your ISP (Internet Service Provider.)

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1500 is the default MTU.

17D-Link DIR-130 User Manual

+ 49 hidden pages