D-Link DI-824VUP+ User Manual
D-Link And TheGreenBow Solution
Wiirr
W
ell
e
A
A
e
e
p
p
s
s
s
s
pllii
p
DII--
D
V
V
c
c
P
N
P
N
attii
a
8
8
o
o
2
2
R
R
n
n
4
V
4
V
o
utt
o
u
N
N
Version 1.00
(2009-4-24)
U
U
err
e
ott
o
P
P
e
e
D-Link International
Confidential and proprietary
1
Revision History
Date Rev. Description Editor
Interoperability Compliance Testing Negotiate mode for
2009-4-24 1.0
Phase1 and Phase2 using TheGreenBow VPN Client and DLink product’s Wireless VPN router DI-824VUP.
John Yoong
1. Introduction
The objective of this document is to provide a guide describing how to configure the
devices to achieve the same environment as show at the network topology.
Users of this document are expected to already possess basic knowledge of D-Link
devices and TheGreenBow VPN program, and are familiar with how to perform basic
configurations. Only important configurations, such as those pertaining to interfacing and
integrating, will be described in this document.
For purpose of reference, configuration files for each device are available for download.
2. Audience
This document is intended for project engineers or end users that need to implement
VPN router DI series and TheGreenBow software at the sites.
3. Objective
This topology consist the scenarios that integrates using TheGreenBow VPN program
and D-Link Wireless VPN router DI-824VUP+ and demonstrate integrations and network
solutions to OBUs, and in addition, to Partners and Customers from D-Link International.
4. List of Equipment and Software
The table below shows the devices information.
Device No. Device Name Device Model Firmware
1 TheGreenBow VPN Client Software 2 Wireless VPN Router DI-824VUP+
4.6x
1.06b21
D-Link International
Confidential and proprietary
2
Network Diagram
5.
Note: DI-824VUP+ Router is set to allow IPSec pass through.
It is important to note that this application note is also applicable to the following VPN
routers:
• DI-804HV
• DI-808HV
• DI-824VUP
• DI-824VUP+
6. Configurations
In this document, we will only describe the main configurations for this Scenario. The
configurations setting for all the D-Link products will not be described here and for more
detail about the product you can download their user guide.
6.1 TheGreenBow VPN client and D-Link wireless VPN router solutions
(DI-824VUP+)
In this scenario the user can connect back to the Branch office cameras by using
TheGreenBow VPN client tunneling to DI-824VUP+.
All configurations are based on Wireless VPN Router DI-824VUP+ (F/W: 1.06b21) and
TheGreenBow VPN Client software (F/W: 4.60.0.0)
The steps in this configuration are:
• Setup DI-824VUP+ for VPN tunneling
• Setup Dynamic VPN
• Setup TheGreenBow VPN client
D-Link International
Confidential and proprietary
3
• Setup Phase 1
• Setup Phase 2
6.1.1) Setup DI-824VUP+ for VPN tunneling
6.1.1.1)
1) Click on the “VPN” and select the “Dynamic VPN”, please ensure
Setup Dynamic VPN
all other VPN setting is clear or disable.
D-Link International
Confidential and proprietary
4
2) Fill in the details as show below and for the “Preshare key” must
be the same as the preshare key set in Thegreenbow VPN Client
software. Next click on “IKE Proposal”
3) Fill in the setting and select the “Encrypt” and “Auth” algorithm
and lastly, add the profile to the setting to active it.
D-Link International
Confidential and proprietary
5
Loading...