Wireless Internet Camera
Wireless G USB 2.0 Adapter
with 3G Mobile Video
System Requirements
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows®, Macintosh®, or Linux-based operating
systems with an installed Ethernet adapter
• Internet Explorer 6.x and above, or Netscape® Navigator 7.0 and
above
Package Contents
D-Link DI-724GU
Wireless 108G Gigabit QoS Router
CAT5 Ethernet Cable Power Adapter
If any of the above items are missing, please contact your reseller.
CD-ROM with
Manual
2D-Link DI-724GU Quick Install Guide
Hardware Overview
WLAN LED
A solid light indicates that the wireless
segment is ready. This LED blinks
during wireless data transmission.
Power LED
A solid light indicates a
proper connection to the
power supply.
Hardware Overview
USB LED
A solid light indicates a connection
to the USB port. This LED blinks
during data transmission.
Status LED
A blinking light indicates that
the DI-724GU is functioning
properly.
WAN LED
A solid light indicates a connection
on the WAN port. This LED blinks
during data transmission.
Local Network LEDs
A s o lid l ight o n ea c h po r t
indicates a connection to an
Ethe r n e t e nable d d e v i ce.
These LEDs blink during data
transmission.
3 D-Link DI-724GU Quick Install Guide
Hardware Overview
USB Port
Connection for a USB printer.
Antennas
Used to connect to 802.11g or
802.11b wireless adapters.
LAN Ports
These are the connections for Ethernet cables to
Ethernet-enabled computers.
WAN Port
This is for the connection of an Ethernet
cable to your Cable or DSL modem.
Reset Button
Pressing this button restores the Router to
its original factory default settings.
Power Receptor
4D-Link DI-724GU Quick Install Guide
Hardware Installation
Hardware Installation
A. First, connect the power adapter to the receptor at the back panel
of the DI-724GU and then plug the other end of the power adapter
to a wall outlet or power strip. The Power LED will turn ON to
indicate proper operation.
B. 1. Power off your Cable or DSL modem; some devices may not
have a on/off switch and will require you to unplug the power
adapter. Now, the DI-724GU should be powered on and the
Cable/DSL modem should be turned off.
2. Cable/DSL modem (Power Off) – DI-724GU (Power On) Connect
an Ethernet cable to the Ethernet jack located on the Cable/DSL
modem. After the Ethernet cable is securely connected, power
on the Cable/DSL modem by turning on the unit or plugging in
the power adapter.
3. Cable/DSL modem (Power On) – DI-724GU (Power On) Insert
the other end of the Ethernet cable to the WAN PORT on the
back panel of the DI-724GU. The WAN LED light will illuminate
to indicate proper connection. If the WAN LED is not illuminated,
please go back to step B1 and repeat the instructions.
C. Insert an Ethernet cable to LAN port 1 on the back panel of the
DI-724GU and an available Ethernet port on the network adapter
in the computer you will use to congure the DI-724GU. The LED
light for LAN Port 1 will illuminate to indicate proper connection.
Note: The LAN Ports on the DI-724GU are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover Ethernet
cable to the LAN Ports.
D. Computers equipped with 802.11g wireless adapters will be able
to connect to the DI-724GU. The DWL-G650 AirPlus Xtreme G
Wireless Cardbus Adapter and the DWL-G520 AirPlus Xtreme G
Wireless PCI Adapter will be able to connect out of the box with
the router using their default wireless settings.
5 D-Link DI-724GU Quick Install Guide
Getting Started
Getting Started
Please remember that D-Link Wireless 108G devices are pre-congured
to connect together, right out of the box, with their default settings.
6D-Link DI-724GU Quick Install Guide
Configuration
Configuration
This section will show you how to congure your new D-Link Wireless
108G Gigabit QoS Router using the D-Link Setup Wizard.
Open your Web browser and type
“http://192.168.0.1” into the URL
address box. Then press the Enter
or Return key.
Select “Admin” from the
User Name drop down menu
and leave the password eld
blank.
Click Log In
Click Run Wizard
7 D-Link DI-724GU Quick Install Guide
Configuration
Click Next
You have the option to establish
a password for the User Name
“Admin”.
Click Next
Choose your time zone from the
drop down list.
Click Next
8D-Link DI-724GU Quick Install Guide