D Link DI634MA2 Users Manual

High Speed Wireless

. Network Adapter

USER’S MANUAL

Model Name:

Version: 1.0

AV10

Date: April/20/05

Please make sure TURN OFF your computer and remove the power cord from your

PC. Open the computer case and then please insert the Wireless mini PCI

Adapter. Once the Wireless mini PCI Adapter is installed , place the

computer case back. Turn ON your computer.

Driver Installation

1. Please select the second option and click “Next”.

2. Please click “Continue Anyway”

High

Speed Wireless Network Adapter

5. Once the installation is successful, a utility program icon will show on your

desktop. To lunch the utility, just double click the icon.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. To maintain compliance with FCC RF exposure compliance
requirements, please avoid direct contact to the transmitting antenna during
transmitting.

This device is intended only for OEM integrators under the following
conditions:

1) The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

2) The transmitter module may not be co-located with any other transmitter

or antenna.

3) The module has to use the same dipole antennas, or dipole antennas with

identical properties are used, AND the relative antenna spacings are

maintained exactly as approved with this FCC ID.

As long as 3 conditions above are met, further

transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID

can not be met (for example

can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.

This transmitter module is authorized only for use in device where the antenna may

End Product Labeling

be installed such that 20 cm may be maintained between the antenna and users (for

example :Access point, Wireless Router..etc.). The final end product must be labeled

in a visible area with the following: “Contains TX FCC ID:

Manual Information That Must be Included

KA2DI634MA2”.

The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the users manual of the end
product which integrate this module.
The users manual for OEM integrators must include the following information in a
prominent location “

IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements,
the antenna used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. D-Link declares that the

Wireless Network Adapter.

(FCC ID: KA2DI634MA2) is limited in CH1~CH11 by

High Speed

specified firmware controlled in the USA.