D-Link DBT-120 User Manual

DBTDBT

DBT

DBTDBT

Bluetooth USB Adapter

Rev.2.0 (08/27/2002)

120120

120

120120

Contents

Introduction.....................................5

Package Contents..............................6

Installing Bluetooth Software ............6

Hardware Installation ........................8

Introduction to Bluetooth Software ....9

Bluetooth Software Basic Operations.14

Client Applications ......................... 20

Local Services.................................29

Configuration Panel ........................31

Security .........................................52

Troubleshooting.............................. 56

Introduction

Introduction to BluetoothIntroduction to Bluetooth

Introduction to Bluetooth

Introduction to BluetoothIntroduction to Bluetooth

The term “Bluetooth” refers to a worldwide standard for the wireless exchange of data between two devices within a short range. In order to exchange data, two Bluetooth devices must establish a connection. Before a connection is established, one device must request a connection with another, where the second device accepts (or rejects) the connection. The originator of the request is known as the client. The device that accepts (or rejects) the request is known as the server. Many Bluetooth devices can act as both client and server. A client Bluetooth device runs a software program that requests a connection to another device as part of its normal operation. For example, the program may request a connection to a remote computer, a printer, or a modem. Becoming a Bluetooth client normally requires an action by the device operator, such as an attempt to browse a remote computer, print a file, or dial out on a modem. Every Bluetooth device that provides a service must be prepared to respond to a connection request. Bluetooth software is always running in the background on the server, ready to respond to connection requests.

Introduction to the D-Link Bluetooth USB AdapterIntroduction to the D-Link Bluetooth USB Adapter

Introduction to the D-Link Bluetooth USB Adapter

Introduction to the D-Link Bluetooth USB AdapterIntroduction to the D-Link Bluetooth USB Adapter

The D-Link Bluetooth USB Adapter is the best solution for quick and easy access to Bluetooth enabled devices without cables or wires. It is a class 2/ 3 low power device. The wireless transmission range of the D-Link Bluetooth USB Adapter is about 15 Meter (45 feet). APC configured as the Bluetooth server can support up to 7 Bluetooth client devices with IP addresses automatically assigned whenthey connect. After finishing the steps outlined in this manual, you will have the ability to share information, obtain network access and take the full advantage of a "connected" environment.

Package Contents

After opening the D-Link Bluetooth Adapter package, check what’s in the package, then refer to the Installation Guide for the fastest way to get up and running with the Bluetooth USB Adapter.

The following items should be found in the Bluetooth USB Adapter box:

• D-Link DBT-120 Bluetooth USB Adapter

• USB Extension Cable

• Installation CD with Manual & Software

• Installation Guide

Installing Bluetooth Software

Uninstalling a previous version of Bluetooth software:Uninstalling a previous version of Bluetooth software:

Uninstalling a previous version of Bluetooth software:

Uninstalling a previous version of Bluetooth software:Uninstalling a previous version of Bluetooth software:

If you are installing the Bluetooth software for the first time, please skip this section.

Any previous versions of the Bluetooth software must be uninstalled before installing an upgraded version.

Please uninstall the software by completing these steps:

1) Close any open programs and insert the Driver CD into your CD-ROM Drive.

2) The Autorun screen will appear. Click on Install Bluetooth Software.

3) The Welcome screen informs you the previous version of BTW you have installed. Click on the Next button to continue.

4) Click on the Remove button from “Remove the Program” screen.

5) When the files have been removed, you will be presented with a screen informing of its completion.

a. Click on the Finish button, a pop-up dialog box will show on the

screen.

b.Click on the Yes button to reboot your PC.

Y ou have now completely uninstalled the previous version of the Bluetooth software.

Installing the Bluetooth software:Installing the Bluetooth software:

Installing the Bluetooth software:

Installing the Bluetooth software:Installing the Bluetooth software:

Be sure to install the Bluetooth software prior to plugging in the USB Adapter to a USB port. If you have connected the Bluetooth adapter to your computer, please remove it, cancel any hardware wizards that may show up, restart your computer and start here.

1) Close any open programs and insert the Driver CD into your CD-ROM Drive.

2) The Autorun screen will appear. Click on Install Bluetooth Software.

3) The Welcome screen informs you that the WIDCOMM Bluetooth Software

Setup program is ready to begin. Click on the Next button.

4) In the License Agreement screen, click on the radio button to the left of I

accept the terms in the license agreement. Click on the Next button.

5) In the Device Information screen:

a. Enter a device name b. Select a device type c. Click on the Next button.

6) In the Destination Folder screen you are asked to confirm the Destination

Folder for the application software. If you would like, you may change the destination folder to another location as the directory . Click on the Next button.

7) The Ready to Install the Program screen informs you that the driver is ready for

installation. Click on the Install button to continue.

Note: Please click on the OK button from the Driver Signature Notice dialog box to proceed with driver installation in Windows 2000 and XP operating systems.

8) When the files have been copied, you will be presented with a screen informing

of its completion.

a. Click on the Finish button, a pop-up dialog box will show on the screen. b. Click the Yes button to reboot your PC.

9) After you reboot your PC, the Bluetooth Icon will reside in the Windows

system tray.

Hardware Installation

The Bluetooth USB Adapter is plug-&-play . After you have the software installed and have rebooted your PC, you can plug the Bluetooth USB Adapter directly into your laptop’s or desktop’s USB port. Or you can plug one end of the USB cable to your computer and plug the Bluetooth USB Adapter to the other end of the USB cable. When you plug the USB Adapter to the USB port, the green LED on the USB Adapter should light up.

Y ou may be prompted by a “Add New Hardware Wizard”, Click “Next” on each screen with the driver CD in your CD-ROM drive to finalize the installation.

Note: The system will show a series of configuration messages in the Windows system tray only when you have the software and hardware installed for the first time. When you unplug and plug the USB Adapter subsequently, the system won’t show the above bubble messages again.

Introduction to Bluetooth Software

The Bluetooth Software is the solution for the seamless integration of Bluetooth

technology into personal computers. The software provides an easy interface to manage the Bluetooth Adapter.

Introduction to Bluetooth SoftwareIntroduction to Bluetooth Software

Introduction to Bluetooth Software

Introduction to Bluetooth SoftwareIntroduction to Bluetooth Software

Most Bluetooth-enabled devices have the capability to act as:

• A Bluetooth server—these devices provide one or more services, such as

access to the Internet, to other Bluetooth devices.

• A Bluetooth client—these devices use the service(s) provided by Bluetooth

servers.

Bluetooth devices that can act as both server and client can often do both at the same time. The Bluetooth software provides:

• Clients with the means:

o To locate other Bluetooth devices in the immediate vicinity (inquiry) o Discover the services that those devices offer (discovery) o Connect to, use, and disconnect from those services.

• Servers with the means to include/exclude individual services in the list of

services they provide to clients.

• Extensive security, including:

o Authorization o Authentication o Encryption

The services supported by Bluetooth Software are:

• Bluetooth Serial Port - establishes a Bluetooth wireless connection

between two devices. The connection may be used by applications as though a physical serial cable connected the devices.

• Dial-up Networking - allows a Bluetooth client to use a modem that is

physically attached to the Bluetooth server.

• Fax - allows a Bluetooth client to wirelessly send a fax using a device that is

physically attached to the Bluetooth server.

• File Transfer - establishes a Bluetooth wireless connection that allows your

computer to perform file system operations on another Bluetooth-enabled device—browse, drag/drop, open, print, cut/copy , paste, delete, rename, etc.

• Information Exchange - establishes a Bluetooth wireless connection

between two devices so that they can exchange personal information manager data such as business cards, calendar items, email messages, and notes.

• Information Synchronization - establishes a Bluetooth wireless connection

between two devices and uses the connection to synchronize Personal Information Manager data between the two devices.

• Network Access - establishes a Bluetooth wireless connection between the

client and a server that is physically connected to the Local Area Network. If the client has permission (user name and password for the LAN), the wireless connection can be used as if the client were hardwired to the LAN.

Note: All Bluetooth servers do not necessarily provide all of these services.

To determine the services provided by a Bluetooth device:

1. On the client, in the Folders panel of My Bluetooth Places, select Entire Bluetooth Neighborhood.

2. In the right panel of Entire Bluetooth Neighborhood, right-click anywhere except on a device name and select Refresh from the pop-up menu.

3. In the Folders panel of My Bluetooth Places, right-click a device and select

Discover Available Services from the pop-up menu to update the available services list. The available services will be displayed in the right panel of My

Bluetooth Places.

Bluetooth Device IdentityBluetooth Device Identity

Bluetooth Device Identity

Bluetooth Device IdentityBluetooth Device Identity

Every Bluetooth device has an unique 48-bit binary Bluetooth Device Address (BDA) burned into its EEPROM (embedded into the device). This address cannot be changed by the end-user. A device’s BDA is usually displayed in hexadecimal format; 00:D0:B7:03:2E:9F is a valid BDA. Each Bluetooth device also has an operator-configurable, user-friendly name to help distinguish it from other Bluetooth devices. The user-friendly name may be up to 99 alphanumeric characters in length and may contain spaces. My Personal Computer is a valid user-friendly name.

Icons Used For Bluetooth Devices and ServicesIcons Used For Bluetooth Devices and Services

Icons Used For Bluetooth Devices and Services

Icons Used For Bluetooth Devices and ServicesIcons Used For Bluetooth Devices and Services

Bluetooth icons provide at-a-glance feedback about a device or service’s status by changing color.

• Device icons for Windows 98SE, 2K and ME.

• Device icons for Windows XP.

Service icons are gray or yellow in color (or gray with yellow accents) in their “normal” state. In the “connected” state the primary color of the icon (gray or yellow) changes to green.

• Service icons for Windows 98SE, 2K and ME.

• Service icons for Windows XP.

Services may be unavailable because they are in use or because the necessary hardware (such as a modem for Dial-up Networking) is not installed.

Bluetooth Software Basic Operations

Find Bluetooth DevicesFind Bluetooth Devices

Find Bluetooth Devices

Find Bluetooth DevicesFind Bluetooth Devices

You can double click on the Bluetooth icon in the Windows system tray or

double click on the My Bluetooth Places on your desktop to launch

the My Bluetooth Places Explorer.

Bluetooth Software Explorer

Open the Bluetooth menu from the above screen and select Search for Devices. The system will start to look for Bluetooth devices in the vicinity and display the devices it finds in the right panel of My Bluetooth Places. The Bluetooth Software can be configured to automatically search for devices on a regular basis. From Configuration Panel/Discovery Tab, check the box of “Look for other Bluetooth devices”. You can set a searching time so that the device will search other Bluetooth devices at a regular time. Note: If you find that some devices are within connection range but do not show up in the list of devices found, the possible causes are:

• Y our device is configured to report only specific types or classes of devices

• The unlisted device is configured to be non-discoverable

Find a ServiceFind a Service

Find a Service

Find a ServiceFind a Service

In the Folders panel of My Bluetooth Explorer, right-click on the device name and select Discover Available Services from the pop-up menu. The services the device provides will show up in the right panel.

Bluetooth Software Explorer – Available Services

The services supported by Bluetooth software are:

• Bluetooth Serial Port - establishes a Bluetooth wireless connection between two devices. The connection may be used by applications as though a physical serial cable connected the devices.

• Dial-up Networking - allows a Bluetooth client to use a modem that is physically attached to the Bluetooth server.

• Fax - allows a Bluetooth client to wirelessly send a fax using a device that is physically attached to the Bluetooth server.

• File Transfer - establishes a Bluetooth wireless connection that allows your computer to perform file system operations on another Bluetooth-enabled device—browse, drag/drop, open, print, cut/copy , paste, delete, rename, etc.

• Information Exchange - establishes a Bluetooth wireless connection between two devices so that they can exchange personal information manager (PIM) data

such as business cards, calendar items, email messages, and notes.

• Information Synchronization - establishes a Bluetooth wireless connection between two devices and uses the connection to synchronize Personal Information Manager data between the two devices.

• Network Access - establishes a Bluetooth wireless connection between the client and a server that is physically connected to the Local Area Network. If the client has permission (user name and password for the LAN), the wireless connection can be used as if the client were hardwired to the LAN. Note: All Bluetooth servers do not necessarily provide all of these services. For example, network gateways only provide access to the Local Area Network (the Network Access service).

Setup a New ConnectionSetup a New Connection

Setup a New Connection

Setup a New ConnectionSetup a New Connection

Through the connection wizard, you can walk through the process of setting up a new Bluetooth connection with another device. Y ou can double click on the Add Bluetooth Connection shortcut in the right panel of My Bluetooth Places or right- click on the Bluetooth icon in the Windows system tray, select Services from the pop-up menu, and then select Connection Wizard from the submenu.

Setup a new connectionSetup a new connection

Setup a new connection

Setup a new connectionSetup a new connection

1. On the first Connection Wizard screen:

a) In the Select a Service drop-down menu, select the type of connection that will be established. (The specific service will be selected later, if necessary.) b) In the “Select a device that provides the service” drop-down menu, select the device that will provide the service. (To update the list of devices displayed, click the Search Devices… button.) c) Optional: select the “Require secure encrypted connection” option to enable an Authentication and Encryption for this connection.

2. Click the Next button:

• If more than one service of the type selected in the Select a Service drop- down menu (above) exists on the selected device, for example, multiple Bluetooth Serial Ports, then the Select Bluetooth Service dialog box appears. Select the specific service to be used, and then click the OK button to close the Select Bluetooth Service dialog box.

• If only one service of the type selected in the Select a Service drop-down menu (above) exists on the selected device, the next Connection Wizard screen appears.

3. If “Require secure encrypted connection” was selected above, a security screen may appear:

• To establish a paired relationship with the remote device while using this wizard, enter your Personal Identification Number in the PIN Code field of the security screen, and then click the Next button.

• To establish the paired relationship with the remote device the first time this connection is used, leave the PIN Code field blank in the security screen, and click the Next button.

• Note: The Security screen WILL NOT appear if the devices have been paired.

4. On the last Connection Wizard screen:

• The top of the screen provides basic information about the new connection— the name of the device that will provide the service and the name of the service that will be provided. If this information is NOT correct, click the Back button to return to the previous screen, and from that screen select the correct service and device.

• In the “Connection Name:” field, enter a descriptive name for the connection, for example, “BT Serial Connection to Andy’s Desktop.”

Bluetooth TrayBluetooth Tray

Bluetooth Tray

Bluetooth TrayBluetooth Tray

The Bluetooth Tray icon resides in the Windows System Tray, which is normally located in the lower-right corner of the screen. Bluetooth Tray provides fast

access to many routine Bluetooth operations. From the Bluetooth Tray you can:

• Access My Bluetooth Places - double-click the Bluetooth icon.

• Access the Bluetooth Configuration Panel - right-click the Bluetooth

icon, select Setup, and then select Configuration from the submenu.

• Access the Bluetooth Security dialog box - right-click the Bluetooth icon, select Setup, and then select Security from the submenu.

• Access the Bluetooth Connection Wizard - right-click the Bluetooth icon, select Services, and then select Connection Wizard from the submenu.

• Exchange Business Cards with another Bluetooth Computer - right- click the Bluetooth icon, select Services, and then select Business Card Exchange from the submenu.

• Search for, and connect to, a specific service - right-click the Bluetooth icon, select Services, and then select the desired service from the submenu. An additional submenu will appear that contains one or more options, including:

Find Devices… or Other Devices and one or more device names. The device name(s) will be present if this computer has used this service, and connected via this technique, at least once before. If a device name is present in the submenu, selecting that device will re-initialize the connection.

The services that can be searched for and connected to from the Bluetooth Tray are:

• Bluetooth Serial Port(s)

• Dial-up Networking

• Fax

• File Transfer

• Information Synchronization

• Network Access.

Send to BluetoothSend to Bluetooth

Send to Bluetooth

Send to BluetoothSend to Bluetooth

This feature is used to send information to another Bluetooth device. Data types include:

• Files from Microsoft Explorer

• Documents from Microsoft Office applications, including:

o Word o Excel o Access o PowerPoint.

• Contacts, appointments, tasks, messages, and notes from Microsoft Outlook.

To use Send to BluetoothTo use Send to Bluetooth

To use Send to Bluetooth

To use Send to BluetoothTo use Send to Bluetooth

In the application:

• Microsoft Explorer - select one or more files to be transferred. Folders cannot be transferred.

• Microsoft Office - only the document in the active window can be transferred.

• Microsoft Outlook - select one or more items to be transferred.

From Microsoft Explorer, go to the File menu, select Send To and then select Bluetooth from the fly-out menu.

• Select Others to display the Select Device dialog box, Or …

• Select a device from the sub-menu.

• Click the OK button to send the data. A dialog box displays progress.

Client Applications

Network AccessNetwork Access

Network Access

Network AccessNetwork Access

The Network Access service permits a Bluetooth client to use a Local Area Network connection that is physically attached to another Bluetooth device (the server). Possible Network Access servers include:

• Bluetooth-enabled computers that have a hardwired Ethernet connection.

• Stand-alone Bluetooth Network Access Points.

The Bluetooth server must be specifically configured to provide the Network Access service. Note: After a Bluetooth device is configured as a Network Access server it cannot act as a Network Access client until it has been re-configured to act as a Network Access client.

Network Access Server-side Setup for Windows2000Network Access Server-side Setup for Windows2000

Network Access Server-side Setup for Windows2000

Network Access Server-side Setup for Windows2000Network Access Server-side Setup for Windows2000

Y ou must configure one computer to serve as a Bluetooth server, and then other Bluetooth client devices in the vicinity can access available services the server provides. Being a Bluetooth Network Access server, the computer must have a hardwired Ethernet connection and be specifically configured to provide the Network Access service.

• From the Windows Start menu scroll to Settings and select Control Panel. On the Control Panel screen, double click on the Network and Dial-up Connections.

• On the Network and Dial-up Connections screen, right-click on the Local Area Connection icon, and select Properties from the pop-up menu.

• On the Local Area Connection Properties screen, click on the Sharing tab; select Enable Internet Connection Sharing for this connection and click on the OK button to close the screen.

Now, you have successfully configured your PC or laptop to the Bluetooth server so Bluetooth client devices in the vicinity can link to the Bluetooth server.

Network Access Server-side Setup for WindowsXP:Network Access Server-side Setup for WindowsXP:

Network Access Server-side Setup for WindowsXP:

Network Access Server-side Setup for WindowsXP:Network Access Server-side Setup for WindowsXP:

• From the Start menu scroll to Control Panel. In the Control Panel screen, double click on the Network and Dial-up Connections icon.

• On the Network and Dial-up Connections screen, right-click on the Local Area Connection icon, and select Properties from the pop-up menu.

• On the Local Area Connection Properties screen, click on the Advanced tab; select Enable Internet Connection Sharing for this connection and click on the OK button to close the screen.

+ 42 hidden pages