Pole Mounting :This series also include a pole mount option. The pole mount socket located on the bottom of the speaker may be used to secure the speaker to a speaker tripod. Always be sure to
fellow the guidelines listed be blow when pole mounting your speaker. 1. Always be sure the stand is designed to support the weight of the
speaker
2.In outdoor situations that are prone to windy conditions and strong wind gust , be sure to use sandbags as additional tripod support , this will greatly reduce the risk of tipping
3.Do not stack speakers on top of each other when mounting on a tripod. Only one speaker should be mounted to a tripod at one time
4.Always position the tripod legs away from foot traffic 5.Extend the tripod legs to their fully extended position to avoid
accidental tipping
6.Observe and follow all safety guidelines and regulations specified by the tripod manufacturer
7.Be sure the tripod is situated on a flat ,level , and stable surface 8.Always tighten all tripod locks
Distributed by:
TechBrands by Electus Distribution Pty.Ltd.
320 Victoria Rd, Rydalmere
NSW 2116 Australia
Ph: 1300 738 555
Int`1: +61 2 8832 3200
Fax: 1300 738 500
www.techbrands.com
CS-2490
OWNER`S MANUAL
Rigging and Mounting Options
Rigging Points : This series speakers include four rigging points. These points are detailed on page six. The rigging points are used to fly or suspend the speaker in the air by some means.
IMPORTANT SAFETY SYMBOLS |
||
|
Use only with the cart, stand, tripod, bracket, |
|
CAUTION |
or table specified by the manufacturer, or |
|
sold with the apparatus. When a cart is used, |
||
RISK OF ELECTRIC SHOCK |
||
use caution when moving the cart/apparatus |
||
DO NOT OPEN |
||
|
combination to avoid injury from tip-over. |
|
The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
The symbol is used in the service documentation to indicate that specific component shall be replaced only by the component specified in that documentation for safety reasons.
Protective grounding terminal |
|
Alternating current/voltage |
ON: Denotes the apparatus is turned on |
Hazardous live terminal |
OFF: Denotes the apparatus is turned off. |
|
° |
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.
1. IMPORTANT SAFETY INSTRUCTIONS
·Read these instructions.
·Keep these instructions.
·Heed all warning.
·Follow all instructions.
·Water & Moisture
The apparatus should be protected from moisture and rain, can not used near water, for example: near bathtub, kitchen sink or a swimming pool, etc.
·Heat
The apparatus should be located away from the heat source such as radiators, stoves or other appliances that produce heat.
·Ventilation
Do not block areas of ventilation opening. Failure to do could result in fire. Always install accordance with the manufacturer's instructions.
·Object and Liquid Entry
Objects do not fall into and liquids are not spilled into the inside of the apparatus for safety.
·Power Cord and Plug
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, refer
to electrician for replacement.
·Power Supply
The apparatus should be connected to the power supply only of the type as marked on the apparatus or described in the manual. Failure to do could result in damage to the product and possibly the user.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
·Fuse
To prevent the risk of fire and damaging the unit, please use only of the recommended fuse type as described in the manual. Before replacing the fuse, make sure the unit turned off and disconnected from the AC outlet.
·Electrical Connection
Improper electrical wiring may invalidate the product warranty.
·Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzol or alcohol.
·Servicing
Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only.
·Only use accessories/attachments or parts recommended by the manufacturer.
6 |
Owner`s Manual 1 |
Loading...