DeWalt DW745 User Manual

Before returning this product call

1-800-4-DEWALT

Questions? See us on the World Wide Web at www.DEWALT.com

IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR

D

EWALT PURCHASE,

call 1-800-4-DEWALT

IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE

YOUR PROBLEM OVER THE PHONE.

IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.

YOUR FEEDBACK IS VITAL TO THE SUCCESS OF

D

EWALT’S QUALITY IMPROVEMENT PROGRAM.

INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.

DW745
Heavy-Duty 10" (254 mm) Compact Job Site Table Saw

Banc de scie circulaire de chantier, compacte et industrielle, de 254 mm (10 po)
Sierra de banco compacta para el lugar de trabajo de 254 mm (10 pulg.)

de alta resistencia

Defi nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read
the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

English

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US TOLL FREE AT: 1-800-4-D

EWALT (1-800-433-9258).

General Safety Rules

WARNING: Read all instructions before operating product. Failure to follow all

instructions listed below may result in electric shock, fire and/or serious injury.

SAVE THESE INSTRUCTIONS

WARNING: FOLLOW ALL WIRING CODES and recommended electrical connections

to prevent shock or electrocution.

Grounding Instructions

If saw is of grounded construction, read the following instructions.

DANGER: SHOCK HAZARD. THIS MACHINE MUST BE GROUNDED WHILE IN USE.

SERIOUS INJURY COULD RESULT.

ALL GROUNDED, CORD-CONNECTED MACHINES

In the event of a malfunction or breakdown, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock. This machine is equipped with
an electric cord having an equipment-grounding conductor and a grounding plug. The
plug must be plugged into a matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances. Do not modify the plug provided - if it
will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper
connection of the equipment-grounding conductor can result in risk of electric shock.
The conductor with insulation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the equipment-grounding conductor
to a live terminal. Check with a qualified electrician or service personnel if the grounding
instructions are not completely understood, or if in doubt as to whether the machine is
properly grounded. Use only three-wire extension cords that have three-prong grounding
type plugs and matching three-conductor receptacles that accept the machine’s plug, as
shown in Figure A. Repair or replace damaged or worn cord immediately.

GROUNDED, CORD-CONNECTED MACHINES INTENDED FOR USE ON A SUPPLY
CIRCUIT HAVING A NOMINAL RATING LESS THAN 150 VOLTS

If the machine is intended for use on a circuit that has an outlet that looks like the one

illustrated in Fig. A, the machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig.
B, may be used to connect this plug to a matching two-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The temporary adapter should be
used only until a properly grounded outlet can be installed by a qualified electrician. The

green-colored rigid ear, lug, and the like, extending from the adapter must be connected
to a permanent ground such as a properly grounded outlet box. Whenever the adapter
is used, it must be held in place with a metal screw. DO NOT use a sheet metal screw.

FIG.A FIG. B FIG. C

GROUNDED

OUTLET

BOX

GROUNDING PIN

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian

Electric Code.

DANGER: IN ALL CASES, MAKE CERTAIN THAT THE RECEPTACLE IN QUESTION IS
PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN
CHECK THE RECEPTACLE.

GROUNDING

MEANS

ADAPTER

FIG. D

GROUNDING PIN

Double Insulation

If saw is of double-insulated construction, read the following instructions.

This symbol
constructed throughout with two separate layers of electrical insulation or one double
thickness of insulation between you and the tool’s electrical system. Tools built with this
insulation system are not intended to be grounded. As a result, your tool is equipped with a
two prong plug which permits you to use extension cords without concern for maintaining a
ground connection. Repair or replace damaged or worn cord immediately

NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting from
a possible electrical insulation failure within the tool.

POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug
(one blade is wider than the other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully into the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install the proper
outlet. Do not change the plug in any way.

represents double insulated construction. Double insulated tools are

Important Safety Instructions

• TO REDUCE THE RISK OF KICKBACK AND OTHER INJURIES, use all components

of the guarding system (blade guard assembly, riving knife and anti-kickback) for every
operation for which they can be used including all through cutting.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that

keys and adjusting wrenches are removed from spindle before turning tool on. Tools,
scrap pieces, and other debris can be thrown at high speed, causing injury.

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

• DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power

tools in damp or wet locations or in rain can cause shock or electrocution. Keep your
work area well-lit to avoid tripping or placing arms, hands, and fingers in danger.

• KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area.

Your shop is a potentially dangerous environment.

• MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing

starter keys. The unauthorized start-up of a machine by a child or visitor may result in
injury.

2

• DO NOT FORCE TOOL. It will do the job better and be safer at the rate for which it was

designed.

• USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not

designed. Using the incorrect tool or attachment may result in personal injury.

• USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.

If your product is equipped with a cord set, use only three-wire extension cords that
have three-prong grounding-type plugs and three-pole receptacles that accept the
tool’s plug. When using an extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table shows the correct size to
use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAGE FOR CORD SETS

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG
Than Than

0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

• WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or

other jewelry to get caught in moving parts. Non-slip footwear is recommended. Wear
protective hair covering to contain long hair. Air vents may cover moving parts and
should also be avoided.

• ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. All users and bystanders
MUST ALWAYS wear certified safety equipment:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

• DO NOT OVERREACH. Keep proper footing and balance at all times. Loss of balance

may cause personal injury.

• MAINTAIN TOOLS WITH CARE. Keep blades sharp and clean for best and safest

performance. Follow instructions for lubricating and changing accessories. Poorly
maintained blades and machines can further damage the blade or machine and/or
cause injury.

• TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE
POWER SOURCE before installing or removing accessories, before adjusting or

changing set-ups, when making repairs or changing locations. Do not touch the plug’s
metal prongs when unplugging or plugging in the cord. An accidental start-up can cause
injury.

• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is
in the “OFF” position before plugging in the power cord. In the event of a power failure,
move the switch to the “OFF” position. An accidental start-up can cause injury.

• USE RECOMMENDED ACCESSORIES. Use only accessories that are recommended
by the manufacturer for your model. Accessories that may be suitable for one tool
may be hazardous when used on another tool. Consult the instruction manual for
recommended accessories. The use of improper accessories may cause risk of injury
to persons.

• NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting

tool is unintentionally contacted.

• CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part

that is damaged should be carefully checked to determine that it will operate properly
and perform its intended function—check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged should be properly repaired or
replaced. Do not use tool if switch does not turn it on and off. Damaged parts can cause
further damage to the machine and/or personal injury.

• DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation

of the blade or cutter only.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave

tool until it comes to a complete stop. Serious injury can result.

• DO NOT OPERATE ELECTRIC TOOLS NEAR FLAMMABLE LIQUIDS OR IN
GASEOUS OR EXPLOSIVE ATMOSPHERES. Motors and switches in these tools may

spark and ignite fumes.

• STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE. DO
NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE OF
DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power

tools may result in serious injury.

• DO NOT ALLOW FAMILIARITY (gained from frequent use of your saw) TO
REPLACE SAFETY RULES. Always remember that a careless fraction of a second is

sufficient to inflict severe injury.

Additional Safety Rules for Table Saws

WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. All users and bystanders
MUST ALWAYS wear certified safety equipment:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Do not expose to rain or use in damp locations.

• AVOID AWKWARD POSITIONS, where a sudden slip could cause a hand to move into
a saw blade.

• NEVER REACH IN BACK OF, OR AROUND, THE CUTTING TOOL with either hand to
hold down the workpiece.

• KEEP ARMS, HANDS AND FINGERS AWAY from the blade to prevent serious injury.

• USE A PUSH STICK THAT IS APPROPRIATE TO THE APPLICATION TO PUSH
WORKPIECES THROUGH THE SAW. A push stick is a wooden or plastic stick, usually
homemade, that should be used whenever the size or shape of the workpiece would
cause you to place your hands within 6" (152 mm) of the blade.

• USE HOLD-DOWNS, JIGS, FIXTURES OR FEATHER BOARDS TO HELP GUIDE
AND CONTROL THE WORKPIECE. Accessories for use with your tool are available at
extra cost from your local dealer or authorized service center. Instructions for making a
push stick, a narrow rip auxiliary fence, a push block and feather boards are included in
this manual.

• DO NOT PERFORM RIPPING, CROSSCUTTING OR ANY OTHER OPERATION
FREEHAND.

• NEVER reach around or over saw blade.

• STABILITY. Make sure the table saw is firmly mounted to a secure surface before use
and does not move.

• NEVER CUT METALS, CEMENT BOARD OR MASONRY. Certain man-made
materials have special instructions for cutting on table saws. Follow the manufacturer’s
recommendations at all times. Damage to the saw and personal injury may result.

3

English

• THE PROPER THROAT PLATE MUST BE LOCKED IN PLACE AT ALL TIMES to

reduce the risk of a thrown workpiece and possible injury.

• USE THE CORRECT SAW BLADE FOR THE INTENDED OPERATION. The blade

must rotate toward the front of the saw. Always tighten the blade arbor nut securely.
Before use, inspect the blade for cracks or missing teeth. Do not use a damaged or dull
blade.

• NEVER ATTEMPT TO FREE A STALLED SAW BLADE WITHOUT FIRST TURNING

English

THE MACHINE OFF AND DISCONNECTING THE SAW FROM THE POWER
SOURCE. If a workpiece or cut-off piece becomes trapped inside the blade guard

assembly, turn saw off and wait for blade to stop before lifting the blade guard assembly
and removing the piece.

• NEVER START THE MACHINE with the workpiece against the blade to reduce the risk

of a thrown workpiece and personal injury.

• NEVER have any part of your body in line with the path of the saw blade. Personal

injury may occur.

• NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP WORK on the table/work area

when the machine is running. A sudden slip could cause a hand to move into the blade.
Severe injury can result.

• CLEAN THE TABLE/WORK AREA BEFORE LEAVING THE MACHINE. Lock

the switch in the “OFF” position and disconnect from the power source to prevent
unauthorized use.

• DO NOT leave a long board (or other workpiece) unsupported so the spring of

the board causes it to shift on the table resulting in loss of control and possible
injury. Provide proper support for the workpiece, based on its size and the type of

operation to be performed. Hold the work firmly against the fence and down against the
table surface.

• IF YOUR SAW makes an unfamiliar noise or if it vibrates excessively, cease operating

immediately, turn unit off and disconnect from power source until the problem has been
located and corrected. Contact a D

EWALT factory service center, a DEWALT authorized

service center or other qualified service personnel if the problem can not be found.

• KEEP OUT of the line of saw blade. Stand to the side whenever possible.

• USE RECOMMENDED ACCESSORIES. The use of improper accessories may cause

risk of personal injury.

• DO NOT OPERATE THIS MACHINE until it is completely assembled and installed

according to the instructions. A machine incorrectly assembled can cause serious
injury.

• OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are

not thoroughly familiar with the operation of this machine. Knowledge is safety.

• ADDITIONAL INFORMATION regarding the safe and proper operation of power tools

(i.e., a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue,
Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available
from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201.
Please refer to the U.S. Department of Labor OSHA 1910.213 Regulations.

TERMS: THE FOLLOWING TERMS WILL BE USED THROUGHOUT THE MANUAL
AND YOU SHOULD BECOME FAMILIAR WITH THEM.

• Thru sawing refers to any cut that completely cuts through the workpiece.

• Non-thru sawing refers to any cut that does not completely cut through the

workpiece.

• Push Stick refers to a wooden or plastic stick, usually homemade, that is used to push

small workpiece through the saw and keeps the operator’s hands clear of the blade.

• Kickback occurs when the saw blade binds in the cut and violently thrusts the

workpiece back toward the operator.

• Freehand refers to cutting without the use of a miter gauge or rip fence or any
other means of guiding or holding the workpiece other than the operator’s hand.

WARNING: Never perform freehand cutting with this saw.

• Plunge cutting refers to blind cuts in the workpiece made by either raising the blade
through the workpiece or lowering the workpiece down to the blade.

WARNING: Never perform plunge cutting with this saw.

• Resawing - Flipping material to make a cut the saw is not capable of making in one
pass.

WARNING: Resawing IS NOT recommended.

SAW BLADE GUARD ASSEMBLY, ANTI-KICKBACK ASSEMBLY AND RIVING KNIFE

Your table saw is equipped with a blade guard assembly, anti-kickback assembly and
riving knife that covers the blade and reduces the possibility of accidental blade contact.
The riving knife is a flat plate that fits into the cut made by the saw blade and effectively
fights kickback by lessening the tendency of the blade to bind in the cut. The blade guard

assembly and anti-kickback assembly can only be used when making through cuts
that sever the wood. When making rabbets and other cuts that make non through
cuts, the blade guard assembly and anti-kickback assembly must be removed and
riving knife lowered to the non through cut position marked on the riving knife. Tw o

anti-kickback pawls are located on the sides of the riving knife that allow the wood to pass
through the blade in the cutting direction but reduce the possibility of the material being
thrown backwards toward the operator.

Use all components of the guarding system (blade guard assembly, riving knife and anti­kickback assembly) for every operation for which they can be used including all through
cutting. If you elect not to use any of these components for a particular application exercise
additional caution regarding control of the workpiece, the use of push sticks, the position of
your hands relative to the blade, the use of safety glasses, the means to avoid kickback and
all other warnings contained in this manual and on the saw itself. Replace the guarding
systems as soon as you return to thru-cutting operations. Keep the guard assembly
in working order.

MAKING A PUSH STICK (Inside Back Cover)

• In order to operate your table saw safely you must use a push stick whenever the size
or shape of the workpiece would cause your hands to be within 6" (152 mm) of the saw
blade or other cutter. A push stick is included with this saw.

• No special wood is needed to make additional push-sticks as long as it’s sturdy and long
enough. A length of 15.7" (400 mm) is recommended with a notch that fits against the
edge of the workpiece to prevent slipping. It’s a good idea to have several push sticks
of the same length [15.7" (400 mm)] with different size notches for different workpiece
thicknesses.

• See the inside back cover for a picture of a push stick. The shape can vary to suit your
own needs as long as it performs its intended function of keeping your hands away from
the blade.

KICKBACKS

KICKBACKS: Kickbacks can cause serious injury. A kickback occurs when a part of the
workpiece binds between the saw blade and the rip fence, or other fixed object, and rises
from the table and is thrown toward the operator. Kickbacks can be avoided by attention to
the following conditions.

How to Avoid Them and Protect Yourself from Possible Injury

a. Be certain that the rip fence is parallel to the saw blade.
b. Do not rip by applying the feed force to the section of the workpiece that will become

the cut-off (free) piece. Feed force when ripping should always be applied between the
saw blade and the fence; use a push stick for narrow work, 6" (152 mm) wide or less.

c. Keep saw blade guard assembly, riving knife and anti-kickback assembly in place

and operating properly. If anti-kickback assembly is not operational, return your unit
to the nearest authorized D

EWALT service center for repair. The riving knife must be

4

in alignment with the saw blade and the anti-kickback assembly must stop a kickback
once it has started. Check their action before ripping by pushing the wood under the
anti-kickback assembly. The teeth must prevent the wood from being pulled toward the
front of the saw.

d. Plastic and composite (like hardboard) materials may be cut on your saw. However,

since these are usually quite hard and slippery, the anti-kickback pawls may not stop
a kickback. Therefore, be especially attentive to following proper set up and cutting
procedures for ripping.

e. Use saw blade guard assembly, anti-kickback assembly and riving knife for every

operation for which it can be used, including all through-sawing.

f. Push the workpiece past the saw blade prior to release.
g. NEVER rip a workpiece that is twisted or warped, or does not have a straight edge to

guide along the fence.

h. NEVER saw a large workpiece that cannot be controlled.
i. NEVER use the fence as a guide or length stop when crosscutting.
j. NEVER saw a workpiece with loose knots, flaws, nails or other foreign objects.
k. NEVER rip a workpiece shorter than 10" (254 mm).
l. NEVER use a dull blade – replace or have resharpened.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well-ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling

and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes or lay on the

skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from face
and body. Always operate tool in well-ventilated area and provide for proper dust removal.
Use dust collection system wherever possible.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

Specifi cations

Amperes 15 A
Miter Angle 60° L and R
Bevel Angle 0° to 45° L
Blade Size 10" (254 mm)
Max. Cut Depth 0° Bevel 3-1/8" (79 mm)
Max. Cut Depth 45° Bevel 2-1/4" (57 mm)
RPM, no load 3850

Unpacking

WARNING: To reduce the risk of injury, DO NOT connect the machine to the power source

until the table saw is completely assembled and you read the entire instruction manual.

Open the box and slide the saw out, as shown in Figure 1. Carefully unpack the table saw
and all loose items from the carton. Examine all parts to make sure that parts have not
been damaged during shipping. If any parts are missing or damaged, contact your dealer to
replace them before attempting to assemble the tool.

Refer to Figure 2 for the loose items and hardware included with the saw:

1. Rip fence

2. Arbor wrench and spindle wrench (attached to saw base)

3. Blade guard assembly

4. Miter gauge

5. Push stick (attached to rip fence)

WARNING: To reduce the risk of serious personal injury, have push stick ready to

use before starting cut.

FIG. 1 FIG. 2

FEATURES (Fig. 3, 4)

Examine Figures 3 and 4 to become familiar with the saw and its various parts. The following
sections on assembly and adjustments will refer to these terms and you must know what
and where the parts are.

C

FIG. 3

A

P

O

M

5

Q

B

D

N

K

J

L

E

N

G

F

H

I

English

FIGURE 3

A. Table J. Bevel lock lever
B. Miter gauge K. ON/OFF switch
C. Blade L. Rip fence indicator
D. Blade guard assembly M. Adjustable feet
E. Fence N. Mounting holes
F. Fence rails O. Cord wrap

English

G. Rip fence front latch P. Handle
H. Fine adjustment knob Q. Anti-kickback assembly
I. Blade height adjustment wheel

FIGURE 4

R. Rip fence rear latch V. Arbor wrench, spindle wrench
S. Dust collection port W. Rail lock lever
T. Dust shroud
U. Push stick

Rip Fence

The rip fence can be installed on the left or right side of your table saw.

TO ASSEMBLE THE RIP FENCE (FIG. 5, 6)

1. Align the locator screw (AA) on the fence rail (F) with the fence head slot and align the
latch (G) with the opening (BB).

2. Secure the rip fence by snapping the latches onto the rails as shown in Figure 6. Be sure
to snap both front (G) and rear (R) latches in place.

FIG. 5

AA

FIG. 6

G

BB

FIG. 4

W

V

D

U

R

S

T

ASSEMBLY

WARNING: Shock Hazard. To reduce the risk of serious personal injury, turn
unit off and disconnect machine from power source before attempting to move it,
change accessories or make any adjustments.

ASSEMBLE YOUR SAW IN THE FOLLOWING ORDER

1. Rip fence (NOTE: Adjust rip scale before proceeding; refer to Rip Scale Adjustment

under Adjustment.)

2. Anti-kickback assembly

3. Blade guard assembly

4. Miter gauge (if required for application)

NOTE: No tools needed for assembly.
NOTE: Wrenches included with your saw are to remove and replace blades.

BB

AA

TO REMOVE THE THROAT PLATE (FIG. 7A)

1. Remove the throat plate (X) by turning the cam lock knob (CC) 1/4 turn
counterclockwise

2. Using finger hole (XX) on the plate, pull throat plate up and forward to expose the inside
of the saw.

FIG. 7A

FIG. 7B

X

YY

XX

CC

FF

A1

ZZ

POSITIONING THE RIVING KNIFE (FIG. 7, 8)

1. Raise the saw blade arbor to its maximum height.

2. Loosen the riving knife lock knob (YY) (minimum of three turns).

3. To disengage riving knife lock pin, push lock knob toward the riving knife as indicated by
the yellow arrows on the knob.

6

FIG. 8A

YY

FIG. 8B

FF

C

FIG. 9

EE

FF

GG

English

4. Lift and slide the riving knife to the approximate position indicated by the markings (non­thru and thru-position) on the riving knife and the lock pin will snap into place.

5. Tighten the riving knife lock knob.

WARNING: Before connecting the table saw to the power source or operating the

saw, always inspect the blade guard assembly and riving knife for proper alignment and
clearance with saw blade. Check alignment after each change of bevel angle.

NOTE: DO NOT operate saw if riving knife is not locked in the thru-cut (ZZ) or non thru-cut
position (A1) hole.

When properly aligned, the riving knife will be in line with the blade at both table top level, and
at the top of the blade. Using a straight edge, ensure that the blade (B) is aligned with the
riving knife (FF) as shown in Figure 8B. With power disconnected, operate the blade tilt and
height adjustments through the extremes of travel and insure the blade guard assembly clears
the blade in all operations and that the anti-kickback assembly is functioning.

TO REPLACE THE THROAT PLATE

1. Align the throat plate as shown in Figure 7A, and insert the tabs on the back of the throat
plate into the holes on the back of the table opening.

2. Rotate cam counterclockwise until the front of throat plate drops into place. Secure
by rotating cam lock knob (CC) clockwise 1/4 turn (when cam lock is under the table
holding the throat plate in place).

3. The throat plate includes four adjustment screws which raise or lower the throat plate.
When properly adjusted, the front of the throat plate should be flush or slightly below
the surface of the table top and secured in place. The rear of the throat plate should be
flush or slightly above the table top.

WARNING: To reduce the risk of serious personal injury, the throat plate must be locked

in place at all times.

Anti-Kickback Assembly (Fig. 9)

WARNING: To reduce the risk of serious personal injury, the anti-kickback assembly

must be in place for all possible cuts.

1. Remove the anti-kickback assembly (Q) from the storage position. See Storage
(page 14).

2. Locate the anti-kickback mounting hole and slot (EE) at the top of the riving knife (FF).

3. Slide the anti-kickback housing along the top of the riving knife until the stem (GG) locates
the slot above the mounting hole. Depress the stem (GG) on the anti-kickback assembly to
allow the assembly to drop into the hole (EE). Push down on the anti-kickback assembly
until it snaps into place and locks the assembly. NOTE: Pull up on the anti-kickback
assembly to ensure it has locked into place.

Q

Q

Blade guard assembly (Fig. 10, 11)

TO ATTACH BLADE GUARD ASSEMBLY

WARNING: To reduce the risk of serious personal injury, the blade guard assembly must

be in place for all possible cuts.

1. While holding the blade guard assembly (D) in a
vertical position slide the locating pin (HH) into the
riving knife slot (II) centering the riving knife within
the v-shaped notch in the top guard. See

FIG. 10

D

Figure 10.

2. Rotate the blade guard assembly towards the front
of the saw while keeping the pin (HH) at the top of
the riving knife slot. Rotate until the blade guard
assembly is parallel to the table. See Figure 11.

3. Press the blade guard lock lever (WW) down until it
snaps into the locked position. Check to make sure
the guard is locked onto the riving knife. If the guard
is not locked the blade guard lock lever will flip up to

HH

II

the unlocked position.

FIG. 11 FIG. 11A FIG. 11B

WW

WW

TO REMOVE THE BLADE GUARD ASSEMBLY

1. Lift the blade guard assembly lock lever (WW) to the unlocked position.

2. Rotate the guard back and slide pin from riving knife slot.

Miter Gauge

NOTE: A large auxiliary miter gauge face may be used.

7

TO ATTACH THE MITER GAUGE

The DW745 includes a miter gauge
for crosscutting materials. The miter
gauge can be used by insertion into
one of the two miter gauge slots (JJ)
in the table top (Fig. 12).

NOTE: See crosscutting and bevel
crosscutting instructions before

English

performing these operations on the
table saw.

FIG. 12

Bench Mounting

NOTE: A portable table saw stand is
designed for use with this saw and is
available at a local D
service center at extra cost.

TO BENCH MOUNT SAW

WARNING: To reduce the risk of serious personal injury, turn unit off and
disconnect machine from power source before attempting to move it, change
accessories or make any adjustments. An accidental start-up can cause injury.

CAUTION: To reduce the risk of personal injury, make sure table saw is firmly mounted

before use.

The table saw must be mounted firmly. Four mounting holes (N, Fig. 3) are provided in the
metal frame for mounting. We strongly recommend that these holes be used to anchor the
table saw to your workbench or other rigid, stationary work support.

CAUTION: Ensure that the surface is stable enough that large pieces of material will not

cause it to tip over during use.

1. Center the saw on the desired, stable work surface.

2. Drive four 3-1/2" (88.9 mm) long screws through the holes in the metal frame. Make

sure the screws extend through the frame and securely attach to the supporting work
surface.

If marring the supporting work surface is a concern, the DW745 can be mounted to scrap
wood which can then be clamped onto the desired work surface.

1. Cut a piece of 3/4" (19 mm) plywood to fit beneath the footprint of the saw.

2. Screw the saw to the plywood and clamp the overhang of the plywood to the work

surface. If the screws protrude through the plywood base, set it on two scrap pieces of
material of equal thickness and attach them to the edges of the plywood to hold the saw
further off of the work surface and prevent the screws from marring the surface.

EWALT dealer or

JJ

Connecting Saw to Power Source

WARNING: To reduce the risk of injury, before connecting saw to power source, make
sure the switch is in the OFF position.

Be sure your power supply agrees with the nameplate marking. AC Only means that your
saw will operate on alternating current only. A voltage decrease of 10 percent or more will
cause a loss of power and overheating. All D
not operate, check the power supply.

EWALT tools are factory tested. If this tool does

On-Off Switch

WARNING: To reduce the risk of injury, be sure switch is in the OFF position before
plugging machine in.

Lift the ON/OFF switch (K) paddle up to turn your saw ON and push it down to turn your
saw OFF.

A hole (KK) is provided in the switch for insertion of a
padlock with a removable shank to lock the saw off
(Fig. 13).

NOTE: A conventional padlock will not fit.

Rip Fence Operation

RAIL LOCK LEVER (FIG. 4)

The rail lock lever (W) locks the fence in place
preventing movement during cutting. To lock the rail

lever, push it down and toward the rear of the saw. To
unlock, pull it up and toward the front of the saw.

NOTE: When ripping, always lock the rail lock lever.
WORK SUPPORT EXTENSION

Your table saw is equipped with a work support extension to support work that extends
beyond the saw table. To use the work support extension, rotate it as shown in Figure 14.
When not in use, the work support extension retracts, as shown in Figure 15.

NOTE: Retract the work support extension whenever working over the table.

FIG. 14

FINE ADJUSTMENT KNOB (FIG. 16)

The fine adjustment knob (H) allows smaller
adjustments when setting the fence. Before
adjusting, be sure the rail lock lever is in its up
or unlocked, position.

RIP SCALE POINTER

The rip scale pointer will need to be adjusted for
proper performance of the rip fence if the user
switches between thick and thin kerf blades. Refer
to Rip Scale Adjustment under Adjustments for
alignment instructions.

FIG. 15

FIG. 16

FIG. 13

KK

K

NN

H

Adjustments

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from

power source before installing and removing accessories, before adjusting or changing

set-ups or when making repairs. An accidental start-up can cause injury.

NOTE: Your saw is fully and accurately adjusted at the factory at the time of manufacture. If
readjustment due to shipping and handling or any other reason is required, follow the steps
below to adjust your saw.

8

Once made, these adjustments should remain accurate. Take a little time now to follow
these directions carefully to maintain the accuracy of which your saw is capable.

RAIL LOCK ADJUSTMENT
(Tightening Fence Clamping System)

FIG. 18

1. Lock the rail lock lever (W).

2. On the underside of the saw, loosen the nut (LL) (Fig. 18).

3. Tighten the hex rod (MM) until the spring on the locking system

is compressed creating the desired tension on the rail lock lever.
Retighten the jam nut against the hex rod.

4. Flip the saw over and check that the fence does not move when

MM

LL

the lock lever is engaged. If the fence is still loose, tighten the
spring further.

RIP SCALE ADJUSTMENT

FIG. 19

(Calibrating Rip Scale)

1. Unlock the rail lock lever (W).

2. Set the blade at 0° bevel and move the

fence until it is flush with the blade.

3. Lock the rail lock lever.

4. Loosen the screws (NN, Fig. 16) in

the rip scale pointer with a Phillips
screwdriver and reset the red line to 0°
on the scale.

5. Tighten the screws back into the rail.

W

NOTE: The rip scale only reads correctly
when the fence is mounted on the right side
of the blade.

BLADE ALIGNMENT ADJUSTMENT
(Blade Parallel to Miter Slot)

WARNING: Cut Hazard. Check the blade
at 0˚ and 45˚ to make sure blade does not
hit the throat plate, causing personal injury.

FIG. 20

If the blade appears to be out of alignment
with the miter slot on the table top, it will
require calibration for alignment. To realign
the blade and miter slot, use the following
procedure:

1. Locate the black Allen locator screws

(OO) that hold up the trunnion to the
bottom of the table in the rear of the
saw.

2. Loosen both screws and align the blade

with the miter slot. Be sure to measure
between the miter slot and the back and
front of the blade to ensure parallelism.

3. Snugly tighten the screws to secure the

trunnion and blade assembly to the table
at the parallel position.

OO

FENCE ALIGNMENT ADJUSTMENT (FIG. 4, 5) (Blade Parallel to Fence)

If you experience fence alignment problems and want to correct an out of parallel between
the fence and the blade, be sure to check the alignment of the blade to the miter slot first.

After confirming that those elements are aligned, proceed with alignment of the blade to the
fence using the following procedure:

1. Unlock the rail lock lever (W) and locate the two fence locator screws (AA) that support
the fence on the front and rear rails.

2. Loosen the rear locator screw and adjust the position of the fence in the groove on the
fence until it sets the fence face parallel to the blade. Make sure you measure from the
fence face to the front and back of the blade to ensure alignment.

3. Tighten the locator screw and repeat on the left side of the blade.

4. Check rip scale adjustment.

BEVEL STOP AND POINTER ADJUSTMENT
(Calibrating Bevel Scale)

Calibrating the bevel system on the saw may require two separate steps, one for the bevel
scale and another for the bevel pointer. The scale should always be checked first followed
by adjustments to the red pointer.

BEVEL LOCK ADJUSTMENT (FIG. 21)

The bevel lock lever (J) may need adjustment to maintain lock force.
To do this, put the lock lever in the locked position. Use a Phillips screwdriver to remove the

screw (PP) holding the lock lever in place (Fig. 21). Remove the lock lever from the locking
bolt and place lock lever in the desired position. Insert the screw (PP) and tighten securely.

FIG. 21

J

J

PP

Part A – Adjusting the Bevel Scale System (Fig. 22, 23)

1. Remove the Blade guard assembly from the saw and raise the blade all the way up in
the table.

2. Unlock the bevel lock lever (J) and loosen the bevel stop screw (QQ).

3. Place a square against the table and blade.

NOTE: Be sure to place the square between the teeth on the blade to ensure an

accurate measurement.

4. Adjust the bevel angle until the blade is flat against the square. Lock the bevel lock
lever (J).

5. Move the bevel stop cam (RR) until it firmly contacts the trunnion casting. Tighten the
bevel stop screw.

6. Repeat procedure at 45˚ using a triangle or speed square.

Part B – Adjusting the Bevel Scale Pointer

NOTE: Complete this step only if Part A has been completed.

7. Check the bevel scale angle. If the pointer does not read 0°, loosen the pointer screw
(SS) and move it to the 0° mark on the bevel scale. Retighten the pointer screw.

English

9

English

FIG. 22

FIG. 23

FIG. 24

QQ

RR

SS

TT

MITER GAUGE ADJUSTMENT
(Calibrating Miter Gauge Pointer)

Your miter gauge features adjustable stops at 90° and 45°

FIG. 25

FF

left and right.
To adjust the miter gauge, loosen the screw (TT) and move

to desired position. Tighten the screw against the stop plate

A1

(Fig. 24).

ALIGNING RIVING KNIFE TO BLADE (FIG. 25)

J

1. Remove the throat plate. See To Remove Throat Plate

under Assembly.

2. Raise the blade to full depth of cut and 0° bevel angle.

ZZ

3. If needed, raise the riving knife (FF) to the thru - cut

(ZZ) or highest position. See Positioning Riving Knife
under Assembly.

4. Locate the three small set screws (A2)

YY

adjacent to the riving knife lock knob (YY). These
screws will be used to adjust the riving knife position.

5. Lay a straight edge on the table against two blade tips.

A2

The riving knife should not touch the straight edge. If
needed, loosen the two larger lock screws (A3).

6. Adjust the small set screws (A2) to move the riving knife
according to the position noted in step 5. Lay the straight
edge on the opposite side of the blade and repeat
adjustments as needed.

7. Lightly tighten the two larger lock screws (A3).

A3

8. Place a square flat against the riving knife to the verify
riving knife is vertical and in-line with the blade.

9. If needed, use the set screws to bring the riving knife

FIG. 26

vertical with the square.

10. Repeat steps 5 and 6 to verify position of riving knife.

11. Fully tighten the two larger lock screws (A3).

Saw Blades

WARNING: Riving knifes must be matched to saw blade

dimensions in order to function effectively. See Riving

Knife selection.
NOTE: THIS SAW IS INTENDED FOR USE ONLY WITH

SAW BLADES 10" (254 mm) IN DIAMETER. See Fig. 26.
NOTE: This saw is not intended for use with dado blades

and molding cutters. Personal injury may occur.

1. The saw blade furnished with your new saw is a 10"
(254 mm) combination blade, used for crosscutting
(across the grain) and ripping (with the grain) through
the material. The center hole to fit on the arbor is
5/8" (16 mm) diameter (.625"). This blade will produce a
good quality cut for most applications.

2. There are many types of blades available to do specific
and special jobs such as cross cut only, rip only, hollow
ground, thin plywood, paneling, etc.

3. Use only saw blades designed for maximum safe
operating speeds of 5,000 RPM or greater.

4. Saw blades should always be kept sharp. It is
recommended that you locate a reputable sharpening
service to sharpen your blades when needed.

CAUTION: Abrasive wheels or blades (including

diamond) should not be used on this saw.

10

Blade (Fig. 3, 27, 28)

REPLACING THE BLADE

1. Raise the saw blade arbor to its
maximum height by turning the blade
height adjustment wheel (I)
clockwise.

2. If replacing the blade, remove the
Blade guard assembly (D) and throat
plate (X) prior to installing the new
blade. (Refer to To Remove Blade
guard assembly under Assembly
and To Remove Throat Plate.)

NOTE: It may be easier to change

the blade with the saw blade
beveled to 45˚.

3. Remove the arbor nut (Y) and outer
washer (Z) and set aside.

4. Place the blade (C) on the arbor
making sure the teeth of the blade
point downward and toward the front of the saw.

5. Place the outer washer (Z) against the blade,
raised side out and tighten the arbor nut against
the washer as far as possible by hand. Ensure that
the outer washer and arbor nut are free of dust and
debris before installing.

6. To further tighten the arbor nut (Y), use the open
ended spindle wrench (supplied) to keep the
spindle from rotating (Fig 27).

7. Use the arbor wrench (supplied) to hold the nut
and tighten it by turning it clockwise. Reposition the
wrench on the arbor nut and repeat as necessary
until the nut and washer are securely fastened
against the blade (Fig. 28).

NOTE: Different types of blades make different kerfs (width of cuts). Therefore, it is
necessary to check adjustment of rip scale when changing blades. Replacement blade
MUST not exceed the thickness stated on the riving knife. The riving knife provided with the
saw is 2.2 mm thick.

FIG. 27

C

Y

Z

FIG. 28

Y

Riving Knife Selection

WARNING: To minimize the risk of kickback and to insure proper cutting, the riving knife

must be the proper thickness for the blade used.

The riving knife supplied with this table saw is the correct size for the blade supplied with
the saw.

If a different blade is used, check the blade body, or plate, thickness and the blade kerf, or
cutting, width marked on the blade or on the blade packaging. The riving knife thickness
must be greater than the body thickness and less than the kerf width as shown in Figure 29.
If it is not, the riving knife MUST be replaced with one that has the correct thickness.

The riving knife provided with this saw is marked as follows (Fig. 30):

0.087" (2.2 mm) THICK RIVING KNIFE. ONLY USE FOR 10" (254 mm) Ø BLADE
WITH 0.094" (2.4 mm) MIN. KERF WIDTH AND 0.067" (1.75 mm) MAX. BODY
THICKNESS.

The Riving knife available as an accessories marketed by D

EWALT is marked as follows:

0.110" (2.8 mm) THICK RIVING KNIFE. ONLY USE FOR 10" (254 mm) Ø BLADE
WITH 0.118" (3.0 mm) MIN. KERF WIDTH AND 0.098" (2.5 mm) MAX. BODY
THICKNESS

FIG. 29

KERF WIDTH

(WIDTH OF CUT

MADE BY THE

BLADE)

BODY (OR PLATE)

THICKNESS OF

THE BLADE

RIVING KNIFE

THICKNESS

FIG. 30

All DEWALT blade body thickness and kerf widths are provided at www.DEWALT.com.
If a different blade is used and the body thickness and kerf width dimensions are not

provided, use the following procedure to determine the correct riving knife thickness:

1. Measure the body thickness of the blade.

FIG. 31

2. Make a shallow cut in scrap material and
measure the kerf width.

3. Select the riving knife as shown in Figure 29.

4. Slide the riving knife through the shallow cut
made in step 2 to confirm the correct riving
knife has been selected. The riving knife
should not bind or drag through the cut.

IMPORTANT: If any dragging or binding of the
material is encountered as it reaches the riving
knife, turn unit off and disconnect machine from
power source. Repeat steps 1–4 to make the
proper riving knife selection before attempting
another cut.

Kickback

Kickback is a dangerous condition! It is caused by the workpiece binding against the blade.
The result is that the workpiece can move rapidly in a direction opposite to the feed direction.
During kickback, the workpiece could be thrown back at the operator. It can also drag the
operator’s hand back into the blade if the operator’s hand is at the rear of the blade. If
kickback occurs, turn the saw OFF and verify the proper functioning of the riving knife, anti­kickback assembly and blade guard assembly before resuming work.

WARNING: See Additional Safety Rules for Table Saws and follow all warnings

provided regarding KICKBACK.

OPERATION

WARNING: Before using the saw, verify the following each and every time:

1. ALWAYS wear proper eye, hearing and respiratory equipment.

2. Blade is tight.

English

11

3. Bevel angle and height lock knobs are tight.

4. If ripping, ensure fence lock lever is tight and fence is parallel to the blade.

5. If crosscutting, miter gauge knob is tight.

6. The blade guard assembly is properly attached and the anti-kickback assembly is
functioning.

7. ALWAYS inspect the blade guard assembly and riving knife for proper alignment,

English

operation and clearance with saw blade.

8. ALWAYS make sure both guards are in the down position in contact with the table
before operating.

Failure to adhere to these common safety rules can greatly increase the likelihood of
injury.

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from

power source before installing and removing accessories, before adjusting or changing

set-ups or when making repairs. An accidental start-up can cause injury.

WARNING: Before connecting the table saw to the power source or operating the saw,

always inspect the blade guard assembly and riving knife for proper operation alignment
and clearance with saw blade. Personal injury may result.

WARNING: Ripping or crosscutting may cause saw to tip over while operating. Make

sure saw is securely mounted to a stable surface.

WARNING: Never use the fence and miter gauge together. This may cause a kickback

condition and injure the operator.

CAUTION: If your saw makes an unfamiliar noise or if it vibrates excessively, cease

operating immediately, turn unit off and disconnect from power source until the problem
has been located and corrected. Contact a D
authorized service center or other qualified service personnel if the problem can not be
found.

CAUTION: The proper throat plate must be in place at all times to reduce the risk of a

thrown work piece and possible injury.

There are two basic types of cutting with table saws: ripping and crosscutting. Cutting
with the grain is ripping and cutting against the grain is crosscutting. With manmade
materials, the distinction is made such that ripping is cutting to a different width and
crosscutting describes cutting material across the shorter dimension.

WARNING: When ripping, always use the fence to provide a guide for the material and

blade guard assembly against a kickback situation.

WARNING: Never perform any cutting operation free hand. Never perform plunge

cutting.

CAUTION: When crosscutting, always use the miter gauge.

EWALT factory service center, a DEWALT

Guard Operating Feature (Fig. 32)

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from

power source before installing and removing accessories, before adjusting or changing

set-ups or when making repairs. An accidental start-up can cause injury.

1. The guard(s) will lock in place when in the raised position.

2. This feature increases visability when measuring the blade to fence distance.

3. Push down on guard(s) and they will release to the operating position.

• ALWAYS make sure both guards are in the down position in contact with the table

before operating.

FIG. 32

OPERATING

POSITION

RAISED

POSITION

Ripping

WARNING: Never touch the “free end” of the work piece or a “free piece” that is cut

off, while the power is ON and/or the saw blade is rotating. Piece may contact the blade
resulting in a thrown work piece and possible injury.

WARNING: A rip fence should ALWAYS be used for ripping operations to prevent loss

of control and personal injury. NEVER perform a ripping operation freehand. ALWAYS lock
the fence to the rail.

WARNING: When bevel ripping and whenever possible, place the fence on the side of

the blade so that the blade is tilted away from the fence and hands. Keep hands clear of
the blade and use a push stick to feed the work piece if there is less than 6" (152 mm)
between the fence and the blade.

1. Lock the rip fence by pressing the rail lock lever down. Remove the miter gauge.

2. Raise the blade so it is about 1/8" (3.2 mm) higher than the top of the work piece.

3. Hold the work piece flat on the table and against the fence. Keep the work piece about
1" (25.4 mm) away from the blade.

CAUTION: The work piece must have

a straight edge against the fence and
must not be warped, twisted or bowed.
Keep both hands away from the blade
and away from the path of the blade.
See proper hand position in Figure 33.

4. Turn the saw on and allow the blade
to come up to speed. Both hands
can be used in starting the cut.
When there is approximately 12"
(305 mm) left to be ripped, use only
one hand, with your thumb pushing
the material, your index and second finger holding the material down and your other
fingers hooked over the fence. Always keep your thumb along side your first two fingers
and near the fence.

5. Keeping the work piece against the table and fence, slowly feed the work piece rearward
all the way through the saw blade. Continue pushing the work piece until it is clear of the
blade guard assembly and it falls off the rear of the table. Do not overload the motor.

6. Never try to pull the work piece back with the blade turning. Turn the switch off, allow the
blade to stop, raise the anti-kickback teeth on each side of the riving knife if necessary
and slide the work piece out.

7. When sawing a long piece of material or a panel, always use a work support. A
sawhorse, rollers, or out feed assembly provides adequate support for this purpose. The
work support must be at the same height as the saw table.

CAUTION: Never push or hold onto the “free” or “cut off” side of the work piece.

FIG. 33

12

Ripping Small Pieces

It is unsafe to rip small pieces. It
is not safe to put your hands
close to the blade. Instead, rip a
larger piece to obtain the
desired piece. When a small
width is to be ripped and the
hand cannot be safely put
between the blade and the rip
fence, use one or more push
sticks. A pattern is included at
the end of this manual to make
push sticks. A push stick (U) is
included with this saw, attached to the rip fence. Use the push stick(s) to hold the work piece
against the table and fence, and push the work piece fully past the blade. See Figure 34.

FIG. 34

U

Narrow Rip Auxiliary Fence
(Fig. 35, 37)

The narrow rip auxiliary fence should be used for a rip measuring 2" (50.8 mm) or narrower.
This fence will allow the guard to remain on the saw when completing narrow ripping. This
fence will provide ample space for proper use of a push block (A12, see Push Block).

1. Follow the diagram in Figure 35 to construct the narrow rip auxiliary fence (A13).

NOTE: A11 should be cut to fit the length of the saw table top and sides (A14) must be
parallel.

FIG. 35

A11

4-3/4"

(121 mm)

IMPORTANT: The over hanging edge (A16, Fig. 36) MUST be square. An uneven lip

could cause the push block to slip or push the material away from the fence.

2-1/2"

(64 mm)

FIG. 36

(121 mm)

A15

1/2"

(12.7 mm)

5-1/4"

(133 mm)

4-3/4"

(127 mm)

12"

(305 mm)

(12.7 mm)

5"

2-1/2" (64 mm)

1/2"

12

"

(305 mm)

A12

A16

1/2"

(12.7 mm)

2. Place the push block (A12, Fig. 37) behind the material and ensure the lip of the block
is flush to the narrow rip auxiliary fence (A13).

3. Once the push block is in place, continue feeding the material until the cut is complete
making sure the push block remains flush to the narrow rip auxiliary fence at all times.

IMPORTANT: The narrow rip auxiliary fence and the over hanging edge (A16, Fig. 36)
should both be the same thickness.

FIG. 37

A12

English

1/2"

(12.7 mm)

3/8"

(9.5 mm)

1"

(25 mm)

A14

3/8"

(9.5 mm)

2. After the narrow rip auxiliary fence is constructed, slip it over the saw table top and place
it flush to the fence as shown in Figure 37.

3. Feed the work piece through until the edge of the material reaches the front edge of the
saw table top.

4. Continue feeding the material using the push block (A12) until the cut is complete.

Push Block (Fig. 36, 37)

IMPORTANT: Only use the push block (A12) with the narrow rip auxiliary fence, see Narrow
Rip auxiliary Fence. The push block should be used once the material being cut reaches

the saw table top.

1. Construct a push block using the diagram in Figure 36.

NOTE: Edges (A15) must be the same size.

A13

Bevel Ripping

This operation is the same as ripping except the bevel angle is set to an angle other than
zero degrees.

WARNING: Before connecting the table saw to the power source or operating the

saw, always inspect the blade guard assembly and riving knife for proper alignment and
clearance with saw blade. Check alignment after each change of bevel angle.

Crosscutting

WARNING: NEVER touch the “free end” of the work piece or a “free piece” that is cut

off, while the power is ON and/or the saw blade is rotating. Piece may contact the blade
resulting in a thrown work piece and possible injury.

WARNING: To reduce the risk of injury, NEVER use the fence as a guide or length stop

when crosscutting.

13

WARNING: NEVER use a length stop on the free end of the work piece when crosscutting.

In short, the cut-off piece in any through-sawing (cutting completely through the work piece)
operation must never be confined — it must be allowed to move away from saw blade to
prevent contact with blade resulting in a thrown work piece and possibly injury.

WARNING: Use caution when starting the cut to prevent binding of the guard against the

work piece resulting in damage to saw and possible injury.

CAUTION: When using a block as a cut-off gauge, the block must be at least 3/4"

(19 mm) thick and is very important that the rear end of the block be positioned so the work

English

piece is clear of the block before it enters the blade to prevent contact with blade resulting
in a thrown work piece and possibly injury.

1. Remove the rip fence and place the miter gauge in the desired slot.

2. Adjust the blade height so that the blade is about 1/8" (3.2 mm) higher than the top of
the work piece.

3. Hold the work piece firmly against the

FIG. 38

miter gauge with the path of the blade in
line with the desired cut location. Keep
the work piece an inch or so in front of
the blade. KEEP BOTH HANDS AWAY
FROM THE BLADE AND THE PATH OF
THE BLADE (Fig. 38).

4. Start the saw motor and allow the blade
to come up to speed.

5. While using both hands to keep the work
piece against the face of the miter gauge,
and holding the work piece flat against
the table, slowly push the work piece
through the blade. See Figure 38.

6. Never try to pull the work piece with the blade turning. Turn the switch off, allow the blade
to stop, and carefully slide the work piece out.

CAUTION: Never touch or hold onto the “free” or “cut off” end of the work piece.

Bevel Crosscutting

FIG. 39

This operation is the same as
crosscutting except that the bevel angle
is set to an angle other than 0°. For
proper hand position, refer to
Figure 39.

WARNING: Before connecting the

table saw to the power source or
operating the saw, always inspect the
blade guard assembly and riving knife
for proper alignment and clearance
with saw blade. Check alignment after
each change of bevel angle.

Mitering

WARNING: Miter angles greater

than 45˚ may force the blade guard
assembly into the saw blade causing
damage to the blade guard assembly
and personal injury. Before starting
the motor, test the operation by
feeding the work piece into the blade
guard assembly. If the blade guard
assembly contacts the blade, place
the work piece under the blade guard
assembly, not touching the blade,
before starting the motor.

CAUTION: Certain work piece

shapes, such as molding may not lift
the blade guard assembly properly. Feed the work piece slowly to start the cut. If the blade
guard assembly contacts the blade, place the work piece under the blade guard assembly,
not touching the blade, before starting the motor.

This operation is the same as crosscutting except the miter gauge is locked at an angle
other than 0°. Hold the work piece FIRMLY against the miter gauge and feed the work piece
slowly into the blade (to prevent the work piece from moving). See Figure 40.

FIG. 40

Miter Gauge Operation

To set your miter gauge, loosen the lock handle and move the miter gauge to the desired
angle.

Compound Mitering

This is a combination of bevel crosscutting and mitering. Follow the instructions for both
bevel crosscutting and mitering.

Featherboard Construction

Featherboards are used to keep the work in contact with the fence and table, and help
prevent kickbacks. Dimensions for making a typical featherboard are shown in Fig. 41.
Make the featherboard from a straight piece of wood that is free of knots and cracks. Clamp
the featherboard to the fence and table so that the leading edge of the featherboard will
support the workpiece until the cut is complete (Fig. 42). An 8" (203 mm) high flat board
can be clamped to the rip fence and the featherboard can be clamped to the 8" (203 mm)
high board.

FIG. 41

4"

(102 mm)

THE KERF

SHOULD BE

ABOUT 1/4"

(6.4 mm) APART

24" (610 mm)

3/4"

(20 mm)

14

60º

5" (127 mm)

WARNING: Use featherboards for all non-thru-sawing operations where the blade guard

assembly, anti-kickback assembly and riving knife cannot be used. Always replace the

blade guard assembly, anti-kickback assembly and riving knife when the non-thru­sawing operation is complete. Make sure the featherboard presses only on the portion

of the workpiece in front of the blade.

FIG. 42

Dust Collection

Your table saw is equipped with a dust shroud

FIG. 43

and dust collection port. For best results,
connect a vacuum to the port at the rear of the
saw.

After extended use, the saw’s dust collection
system may become clogged. To clear the
dust collection system:

1. Unplug the saw.

2. Turn the saw on its side, so the bottom,
open part of the unit is accessible.

3. Open the dust access door (UU) shown

UU

VV

in Figure 43 by removing the wing screws
(VV). Clean out the excess dust, and re-secure the access door with the wing screws.

Lubrication

FIG. 44

1. All motor bearings are permanently lubricated
at the factory and no additional lubrication is
needed.

2. The height adjustment gear may require
periodic cleaning and lubrication (Fig. 44). If
you have difficulty raising or lowering
the blade, contact a D

EWALT authorized

service center.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been

tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only D

EWALT recommended accessories should be used with

this product.

If you need assistance in locating any accessory, please contact D
Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D
or visit our website www.D

EWALT.com.

EWALT Industrial Tool

EWALT (1-800-433-9258)

STORAGE (Fig. 45, 46)

1. Attach push stick (U) to fence.

2. Remove Blade guard assembly. See To Remove Blade guard assembly. Slide Blade

guard assembly into brackets as shown.

3. Depress the stem (GG) on the anti- kickback
assembly (Q) to allow the assembly to slide from the
riving knife slot.

4. Position anti-kickback assembly into the storage hole
as shown. While depressing stem (GG) slide the anti­kickback assembly across the storage slot (A4) and
release pin to lock into place.

5. Loosen the riving knife lock knob (YY, Fig. 25)
(minimum of three turns).

6. Push riving knife lock knob (YY) toward the riving knife as indicated by the yellow arrows
on the knob to disengage riving knife lock pin.

7. Lift and slide the riving knife from saw.

8. Remove wingnut securing blade wrenches. Place riving knife onto post with blade
wrenches and secure with wingnut.

FIG. 46

Q

FF

D

V

U

FIG. 45

Q

A4

GG

English

15

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from

power source before installing and removing accessories, before adjusting or changing

set-ups or when making repairs. An accidental start-up can cause injury.

Cleaning

WARNING: When cleaning, use only mild soap and a damp cloth on plastic parts. Many

household cleaners contain chemicals which could seriously damage plastic. Also, do not

English

use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products
which may seriously damage plastic parts. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should be performed by a D
service center, a D
Always use identical replacement parts.

EWALT authorized service center or other qualified service personnel.

EWALT factory

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship
for three years from the date of purchase. This warranty does not cover part failure due
to normal wear or tool abuse. For further detail of warranty coverage and warranty repair
information, visit www.D
warranty does not apply to accessories or damage caused where repairs have been made
or attempted by others. This warranty gives you specific legal rights and you may have other
rights which vary in certain states or provinces.

In addition to the warranty, D

D

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any

time during the first year after purchase.

If you are not completely satisfied with the performance of your D
or Nailer for any reason, you can return it within 90 days from the date of purchase with a
receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained either
in the packaging, call the local company or see website for warranty information.

EWALT.com or call 1-800-4-DEWALT (1-800-433-9258). This

EWALT tools are covered by our:

1 YEAR FREE SERVICE

90 DAY MONEY BACK GUARANTEE

EWALT Power Tool, Laser,

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-D

EWALT for a free replacement.

16