DeWalt DW744 User Manual

4.7 (12)
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DW744
Table Saw
Scies circulaires à table
Sierra de banco
GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO. SI TIENE DUDAS, POR FAVOR LLAME.
Before returning this product
call
1-800-4-DEWALT
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE,
CALL 1-800-4 DEWALT.
IN MOST CASES, A DEWALT REPRESENTIVE CAN RESOLVE YOUR
PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.
YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DEWALT'S
QUALITY IMPROVEMENT PROGRAM.
See our catalog on the World Wide Web at www.dewalt.com
4
English
D
E
WALT… BUILT JOBSITE TOUGH
DEWALT high performance industrial tools are made for America’s tough-
est industrial and construction applications. The design of every tool in the
line – from drills to sanders to grinders – is the result of rigorous use on
jobsites and throughout industry. Each tool is produced with painstaking
precision using advanced manufacturing systems and intense quality
control. Every tool is checked before it leaves the factory to make sure
that it meets your standards for durability, reliability and power.
D
EWALT Built Jobsite Tough…WE GUARANTEE IT.
WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING SAW • ALWAYS WEAR EYE PROTECTION • DO NOT WEAR
GLOVES, NECKTIES, JEWELRY OR LOOSE CLOTHING • CONTAIN LONG HAIR • KEEP HANDS AND FINGERS OUT OF THE SAW BLADE PATH — USE EXTRA
CAUTION WHEN BEVELING • ALWAYS USE BLADE GUARD AND SPREADER FOR EVERY OPERATION FOR WHICH IT CAN BE USED, INCLUDING THROUGH
SAWING • USE A “PUSH STICK” WHEN REQUIRED • KNOW HOW TO AVOID KICKBACKS — SEE MANUAL • ALWAYS SUPPORT WORK WITH TABLE AND
FENCE OR MITER GAUGE • NEVER USE FENCE AND MITER GAUGE TOGETHER • NEVER REACH AROUND OR OVER SAW BLADE • SECURELY MOUNT
SAW BLADE BEFORE OPERATING • NEVER REMOVE JAMMED OR CUT-OFF PIECES UNTIL POWER IS OFF AND BLADE HAS STOPPED • DO NOT EXPOSE
TO RAIN OR USE IN DAMP LOCATIONS • SECURE TOOL PROPERLY TO PREVENT UNEXPECTED MOVEMENT • DO NOT OPERATE THIS MACHINE WHILE
UNDER THE INFLUENCE OF ALCOHOL OR DRUGS • FAILURE TO COMPLY WITH THESE WARNINGS MAY RESULT IN SERIOUS PERSONAL INJURY.
WARNING: For your own safety read instruction manual before operating table saw.
WARNING: When using electric tools, basic safety precautions should always be followed
to reduce risk of fire, electric shock, and personal injury, including the following:
Double Insulation
Double insulated tools are constructed throughout with two separate layers of electrical insu-
lation or one double thickness of insulation between you and the tool’s electrical system.
Tools built with this insulation system are not intended to be grounded. As a result, your tool
is equipped with a two prong plug which permits you to use extension cords without concern
for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when operat-
ing this tool. The insulation system is for added protection against injury resulting from a pos-
sible electrical insulation failure within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair
or replace damaged cords.
Polarized Plugs
To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
Important Safety Instructions
KEEP GUARDS IN PLACE and in working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys
and adjusting wrenches are removed from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet
locations, or expose them to rain. Keep work area well lighted.
KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter
keys.
DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more AWG
Than Than
0- 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
Air vents often cover moving parts and
should also be avoided.
ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses, they are not safety glasses.
SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using
your hand and it frees both hands to operate tool.
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits,
cutters, and the like.
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position
before plugging in.
USE RECOMMENDED ACCESSORIES. Consult the instruction manual for recommended
accessories. The use of improper accessories may cause risk of injury to persons.
NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool
is unintentionally contacted.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform
its intended function–check for alignment of moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or replaced.
DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of
the blade or cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
Additional Safety Rules for Table Saw
WARNING: For your own safety, do not operate your saw until it is completely assembled
and installed according to the instructions and until you have read and understood the following:
All Safety Rules Adjustment Procedures
Assembly Procedures Basic Operations
Operating Controls
KEEP GUARDS in place and in working order.
STABILITY. Make sure table saw is firmly mounted before use.
MINIMIZE ACCIDENT POTENTIAL. Most accidents are caused by failure to follow setup
and operating instructions.
AVOID awkward hand positions, where a sudden slip could cause a hand to move into a
saw blade or other cutting tool. Never reach in back of, or around, the cutting tool with
either hand to hold down the workpiece. DO NOT PLACE FINGERS OR HANDS IN THE
PATH OF THE SAW BLADE.
NEVER reach under your machine when operating or make any adjustments when it is
running.
SHUT OFF the saw and disconnect the power cord when removing the table insert, chang-
ing the cutting tool, removing or replacing the blade guard, or making adjustments.
ALWAYS maintain control of the workpiece. DO NOT let go of the workpiece until it is well
clear of the cutting tool.
WHEN REMOVING short workpieces, or cleaning up around the table, be sure the saw is
in the OFF position and blade has stopped turning.
NEVER turn the saw ON before clearing the table of all tools, wood scraps, etc., except
the workpiece and related feed or support devices for the operation planned.
WHEN changing saw location, disconnect power.
USE extra caution when the guard assembly is removed for resawing, dadoing, rabbeting,
or molding. Replace the guard as soon as that operation is completed.
1
English
NEVER hold onto or touch the “free end” of the workpiece
or a “free piece” that is cut off, while power is ON and/or
the saw blade is rotating.
IF YOU STALL OR JAM the saw blade in the workpiece,
turn saw OFF, remove the workpiece from the saw blade,
and check to see if the saw blade is parallel to the miter
gauge slots or grooves and if the splitter is in proper
alignment with the saw blade. If ripping at the time, check
to see if the rip fence is parallel with the saw blade.
Readjust as indicated.
WARNING: Do not allow familiarity (gained from frequent
use of your saw) to replace following safety rules. Always
remember that a careless fraction of a second is sufficient
to inflict severe injury.
MAKE SURE your fingers do not contact the terminals of
the power cord when installing or removing the plug to or
from the line power source.
KICKBACKS - Kickbacks can cause serious injury. A
kickback occurs when a part of the workpiece binds
between the saw blade and the rip fence, or other fixed
object, and rises from the table and is thrown toward the
operator. Kickbacks can be avoided by attention to the
following conditions:
KICKBACKS—HOW TO AVOID THEM AND
PROTECT YOURSELF FROM POSSIBLE INJURY.
a) Be certain that the saw blade is parallel to the rip fence.
Adjust fence if not parallel.
b) Do not rip by applying the feed force to the section of the
workpiece that will become the cut-off (free) piece. Feed
force when ripping should always be applied between
the saw blade and the fence…use a push stick for short
work, 6" (152mm) wide or less. For less than 2" (51mm)
wide, you must use a special fixture.
c) Keep saw blade guard, splitter and anti-kickback teeth
in place and operating properly. Keep teeth sharp. If
teeth are not operational, return your unit to the
nearest D
EWALT Service Center for repair. The
splitter must be in alignment with the saw blade and the
teeth must stop a kickback once it has started. Check
their action before ripping by pushing the wood under
the anti-kickback teeth. The teeth must prevent the
wood from being pulled toward the front of the saw.
d) Plastic and composition (like hardboard) materials may
be cut on your saw. However, since these are usually
quite hard and slippery, the anti-kickback teeth may not
stop a kickback. Therefore, be especially attentive to
following proper set up and cutting procedures for
ripping.
e) Use saw blade guard and splitter for every operation for
which it can be used, including all through sawing.
DO NOT leave a long board (or other workpiece)
unsupported so the spring of the board causes it to shift on
the table. Provide proper support for the workpiece, based
on its size and the type of operation to be performed. Hold
the work firmly against the fence and down against the
table surface.
NEVER use a length stop on the free end of the workpiece
when crosscutting. Never hang onto or touch the free end
of the workpiece when crosscutting, or a free piece that is
cut off when ripping while power is ON and/or the saw
blade is rotating. In short, the cut-off piece in any “thru-
sawing” (cutting completely through the workpiece)
operation must never be confined — it must be allowed to
move away from saw blade.
IF YOUR SAW makes an unfamiliar noise or if it vibrates
excessively, cease operating immediately until the source
has been located and the problem corrected.
KEEP OUT of the line of saw blade. Stand to the side
whenever possible.
USE a push-stick when required. (See page 9)
PAY particular attention to instructions on reducing risk of
kickback.
DO NOT perform any operation free hand.
NEVER reach around, behind or over saw blade.
USE RECOMMENDED ACCESSORIES. The use of
improper accessories may cause risk of personal injury.
WARNING: Some dust created by power sanding, saw-
ing, grinding, drilling, and other construction activities con-
tains chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these chemi-
cals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other
masonry products, and
arsenic and chromium from chemically-treated lum-
ber (CCA).
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sand-
ing, sawing, grinding, drilling, and other construc-
tion activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to
get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse
dust, which may cause serious and permanent respiratory
or other injury. Always use NIOSH/OSHA approved respira-
tory protection appropriate for the dust exposure. Direct par-
ticles away from face and body.
CAUTION: Wear appropriate hearing protection dur-
ing use. Under some conditions and duration of use, noise
from this product may contribute to hearing loss.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
English
1
4
2
3
6
5
FIG. 2
FIG. 1
2
3
English
Specifications
Horsepower 2-1/2
Table Size 19 1/4" x 26 1/2"
Miter Angle 30° L&R
Bevel Angle to 45°L
Blade Size 10" (254mm)
Max. Cut Depth Bevel ................3 1/8" (79mm)
Max. Cut Depth 45° Bevel ..............2-1/4" (57mm)
RPM, no load 3650
Unpacking
Open the box and slide the saw out , as shown in Figure 1.
Carefully unpack the table saw and all loose items from the
carton. Examine all parts to make sure that parts have not
been damaged during shipping. If any parts are missing or
damaged, contact your dealer to replace them before
attempting to assemble the tool.
Figure 2 shows all the loose items and hardware packed with
the saw.
1. Rip fence
2. Blade (attached to saw base)
3. Arbor wrench and spindle wrench (attached to saw
base)
4. Blade guard
5. Throat plate
6. Miter gauge
Examine Figures 3 & 4 to become familiar with the saw and
its various parts. The following sections on assembly and
adjustments will refer to these terms and you must know
what and where the parts are.
Assembly
YOUR SAW SHOULD BE ASSEMBLED IN THE
FOLLOWING ORDER:
1. Blade
2. Rip fence (NOTE: Adjust rip scale before proceeding.
See “Adjusting Rip Scale”.)
3. Blade guard
4. Throat plate
FIG. 3
TABLE
MITER
GAUGE
SCREW-DOWN
HOLES
MOUNTING
HOLES
RAIL LOCK
LEVER
BEVEL LOCK
LEVER
ON-OFF SWITCH
ANTI-KICKBACK TEETH
DUST EXHAUST
RIP FENCE
LATCH
BLADE HEIGHT
ADJUSTMENT
WHEEL
FINE ADJUST
KNOB
RIP SCALE INDICATOR
WORK SUPPORT
EXTENSION
(RETRACTED)
BLADE/WRENCH
STORAGE
FIG. 4
FIG. 5
PIN
OPENING
BLADE GUARD
4
Tools needed for assembly include a screwdriver and the
wrenches included with your saw.
ASSEMBLING THE RIP FENCE
The rip fence can be installed on the left or right side of your
table saw.
1. Locate the pin and opening on fence rails, as shown in
Figure 5. Align the pin with the slot and align the latch
with the opening.
2. Secure the rip fence by snapping the latches onto the
rails as shown in Figure 6. Be sure to snap both latches
in place.
ATTACHING/REPLACING THE BLADE
1. Raise the saw blade arbor to its maximum height by
turning the blade height adjustment wheel clockwise.
2. Remove the arbor nut and flange from the saw arbor by
turning counterclockwise.
3. Place the saw blade on to the spindle making sure the
teeth of the blade point down at the front of the table.
Assemble the washers and arbor nut to the spindle and
tighten arbor nut as far as possible by hand, making
sure that the saw blade is against the inner washer and
the large washer diameters are against the blade.
Ensure the side of outer washer marked “Blade Side” is
against the blade (see Figure 7). Ensure the spindle and
washers are free from dust and debris.
4. To keep the spindle from rotating when tightening the
arbor nut, use the open-ended spindle wrench to secure
the spindle (see Figure 8).
5. Using the arbor wrench, tighten the arbor nut by turn-
ing it clockwise (see Figure 8).
6. NOTE: Different types of blades make different kerfs
(width of cuts). Therefore, it is necessary to check
adjustment of rip fence pointer and blade guard splitter
when changing blades.
ADJUSTING THE RIP SCALE
1. Unlock the rail lock lever (see Figure 9).
2. Set the blade at 0˚ bevel and move the fence in until it
touches the blade.
3. Lock the rail lock lever.
4. Loosen the rip scale pointer screws (see Figure 16) and
set the rip scale pointer to read zero (0). Retighten the
rip scale pointer screws. The rip scale reads correctly
only when the fence is mounted on the right side of the
blade.
ATTACHING THE BLADE GUARD
1. Raise the saw blade arbor to its maximum height by
turning the blade height adjustment wheel clockwise.
2. Loosen, but do not remove the two bolts shown in
Figure 10.
3. Insert the blade guard as shown in Figure 11, ensuring
the bolts fit into the slots on the blade guard. The edge
of the splitter should protrude below and hook under the
shims. Tighten the bolts. Make sure the splitter is cen-
tered and parallel to the blade by lining up the parts with
a straight edge. If the blade and splitter are not aligned,
loosen, but do not remove the bolts again. Remove the
guard and reinsert it after adjusting the shims. These
shims allow for precision alignment of the blade and
splitter. Tighten the bolts securely. Make sure that there
is clearance between the splitter and the blade, and
that the blade spins freely. If the splitter is tilted relative
to the blade, the splitter plate can be bent until it lines
up correctly.
IMPORTANT: THE GUARD SHOULD BE IN PLACE
FOR ALL POSSIBLE CUTS.
4. Retighten the bolts securely.
WARNING: Before connecting the table saw to the power
source or operating the saw, always inspect the guard and
splitter for proper alignment and clearance with saw blade.
Check alignment after each change of bevel angle.
When properly aligned, the splitter will be in line with the
blade at both table top level, and at the top of the blade.
Check using the straight edge. With power disconnected,
operate the blade tilt and height adjustments through the
extremes of travel and insure the guard clears the blade in all
operations and that the anti-kickback teeth are functioning.
ATTACHING THE THROAT PLATE
1. Align the throat plate as shown in Figure 12, and insert
the tabs on the back of the throat plate into the holes on
the back of the table.
2. Press down on the front of the throat plate to snap it into
place.
3. The throat plate includes four adjustment screws which
raise or lower the throat plate. When properly adjusted,
the front of the throat plate should be flush or slightly
below the surface of the table top and secured in place.
The rear of the throat plate should be flush or slightly
above the table top.
4. Turn the cam lock screw (Detail Fig. 12) clockwise 1/4
turn to lock the throat plate in place.
CAUTION: The throat plate must be in place at all times.
Bench Mounting
TURN OFF AND UNPLUG TABLE SAW
The table saw must be mounted firmly. The mounting sur-
face must have a 15" by 20" opening to allow dust to
escape.
Four holes are provided in the tool’s feet for mounting. We
strongly recommend that these holes be used to anchor the
table saw to your workbench or other stationary rigid frame.
Alternately, to enhance the saw’s portability, it can be
mounted to a piece of wood that can be “C” clamped to your
work surface, stand or Workmate® Workcenter. The
D
EWALT DW7440 Table Saw Stand is designed for use with
this saw, and is available from your local D
EWALT dealer or
service center.
English
FIG. 6
FIG. 7
ARBOR
NUT
OUTER
WASHER
INNER
WASHER
SPINDLE
BLADE
FIG. 7A
10MM HEX BOLTS
REAR
PIVOT
BRACKET
(SAW SHOWN UPSIDE DOWN FOR CLARITY)
TORX HEAD
BOLTS
REAR PINION BEARING ASSEMBLY
5
English
CAUTION: Failure to securely mount the table saw to the
work surface can be hazardous.
1. Center the saw on a square piece of 1/2" (12.7mm) ply-
wood. The plywood must have a 15" by 20" opening to
allow dust to escape.
2. Mark the positions of the four mounting holes in the base
of the saw with a pencil.
3. Remove the saw and drill 1/4" (6.4mm) holes in the
places you have just marked.
4. Position the saw over the four holes you drilled in the
plywood and insert four 1/4" (6.4mm) machine screws
FROM THE BOTTOM. Install washers and 1/4" (6.4mm)
nuts on the top. Tighten securely.
5. In order to prevent the screw heads from marring the
surface to which you clamp the saw, attach two strips of
scrap wood to the bottom of the plywood base. These
strips can be attached with glue, or wood screws can be
installed from the top side as long as they don’t protrude
through the bottom of the strip.
6. “C” clamp the plywood base to your workbench when-
ever you want to use the saw.
CAUTION: Make sure table saw is firmly mounted before
use.
Connecting Saw to Power Source
IMPORTANT: Before connecting saw to power source,
make sure the switch is in the OFF position.
Be sure your power supply agrees with the nameplate mark-
ing. AC ONLY means that your saw will operate on alternat-
ing current only. A voltage decrease of 10 percent or more
will cause a loss of power and overheating. All DeWalt tools
are factory tested. If this tool does not operate, check the
power supply.
Rip Fence Operation
RAIL LOCK LEVER
The rail lock lever locks the rip fence rails in place, prevent-
ing their movement. To lock the rail lock lever, push it down.
To unlock the lever, pull it up (see Figure 9).
NOTE: When ripping, always lock the rail lock lever.
WORK SUPPORT EXTENSION
Your table saw is equipped with a work support extension to
support work that extends beyond the saw table. To use the
work support extension, rotate it as shown in Figure 13.
When not in use, the work support extension retracts, as
shown in Figure 14.
NOTE: Retract the work support extension whenever work-
ing over the table.
FINE ADJUST KNOB
The fine adjust knob (shown in Figure 15) allows smaller
adjustments when setting the fence. Before adjusting, be
sure the rail lock lever is in its up, or unlocked, position.
RIP SCALE POINTER
NOTE: The rip scale pointer will need to be readjusted
whenever a thicker or thinner blade is installed.
FIG.8
FIG. 10
BOLTS
SHIMS
ARBOR
WRENCH
FIG. 11
FIG. 12
FIG. 13
FIG. 14
EDGE OF
SPLITTER
FIG. 9
RAIL LOCK LEVER
On-Off Switch
Lift the switch paddle up to turn your saw ON and push it
down to turn your saw OFF.
A hole is provided in the switch for insertion of a padlock to
lock the saw off (Figure 17).
WARNING: Be sure switch is in the OFF position before
plugging machine in.
Adjustments
NOTE: Your saw is fully and accurately adjusted at the fac-
tory at the time of manufacture. If readjustment due to ship-
ping and handling or any other reason is required, follow the
steps below to adjust your saw.
Once made, these adjustments should remain accurate.
Take a little time now to follow these directions carefully to
maintain the accuracy of which your saw is capable.
RAIL LOCK ADJUSTMENT
1. Lock the rail lock lever (Figure 9) by pushing down.
2. On the underside of your saw, tighten the nut shown in
Figure 18. Adjust this nut until the gap between the
belleville washers closes.
3. Once the springs are almost touching, tighten the nut
1/2 turn.
RIP SCALE ADJUSTMENT
See “ADJUSTING THE RIP SCALE” on page 4.
ADJUST BLADE ALIGNMENT TO TABLE
1. THE SAW MUST BE UNPLUGGED BEFORE YOU
MAKE ANY ADJUSTMENT TO THE BLADE.
2. Place the unit in an upright position. Using a 10mm
socket, loosen rear pivot bracket fasteners just enough
to allow the bracket to move side-to-side.(Figure 7A).
3. Adjust the bracket until the blade is parallel to the miter
gauge slot.
4. Tighten the rear pivot bracket fasteners to 7-8 ft.lbs.
BEVEL STOP AND POINTER ADJUSTMENT
1. Raise the blade fully by rotating the blade height adjust-
ment wheel clockwise until it stops.
2. Unlock the bevel lock lever (Figure 3) by pushing it up
and to the right. Loosen the bevel stop screw
(Figure 19).
3. Place a square flat against the table top and against the
blade between teeth, as shown in Figure 20. Ensure the
bevel lock lever is in its unlocked, or up, position.
4. Using the bevel lock lever, adjust the bevel angle until it
is flat against the square.
5. Tighten the bevel lock lever by pushing it down.
6. Turn the bevel stop cam until it firmly contacts the bear-
ing block. Tighten the bevel stop screw.
7. Check the bevel angle scale. If the pointer does not read
0°, loosen pointer screw (see Figure 19) and move the
pointer so it reads correctly. Retighten the pointer screw.
8. Repeat at 45°, but do not adjust pointer.
MITER GAUGE ADJUSTMENT
Your miter gauge features adjustable stops at 90° and 45°
left and right. To adjust these stops, loosen the lock nuts and
tighten or loosen the three adjusting screws against the stop
plate (see Figure 21).
FENCE PARALLEL ADJUSTMENT
1. Unlock rail lock lever.
2. Locate rear pinion bearing and loosen the two hex bolts
just enough to allow side-to-side movement.
3. Adjust fence parallel to blade.
4. Lock rail lock lever and check parallel alignment of the
blade.
5. Tighten the 2 hex bolts that secure the rear pinion bear-
ing assembly to the table.
NOTE: If there is not enough travel in the pinion bearing
assembly to allow the fence to be parallel to the blade,
take the unit to an authorized service center.
RACK AND PINION MESH ADJUSTMENT
Proper adjustment of the rack and pinion mesh is done at
the factory. If it should become necessary to adjust the rack
and pinion mesh, use the following procedure.
1. Turn the saw upside down and locate the front pinion
bearing.
2. Using a narrow blade screw driver or #20 torx driver,
access the screw through the slot. Loosen the screw
(counterclockwise) until the head touches the inside of
the bearing box.
3. Tighten the screw (clockwise) 3/4 of a turn.
4. Repeat procedure for rear pinion bearing.
Saw Blades
THIS SAW IS INTENDED FOR THE USE OF SAW
BLADES 10" IN DIAMETER OR SMALLER
1. The saw blade furnished with your new saw is a 10"
(254mm) combination blade, used for cross cutting
(across the grain) and ripping (with the grain) through
the material. The center hole to fit on the arbor is 5/8"
(16mm) diameter (.625"). This blade will produce a good
quality cut for most applications.
2. There are many types of blades available to do specific
and special jobs such as cross cut only, rip only, hollow
ground, thin plywood, paneling, etc.
3. Use only saw blades designed for maximum safe oper-
ating speeds of 5,000 RPM or greater.
4. Saw blades should always be kept sharp. It is recom-
mended that you locate a reputable sharpening service
to sharpen your blades when needed.
5. Never stack blades on top of one another to store. Place
material such as cardboard between them to keep the
blades from coming in contact with one another.
CAUTION: Abrasive wheels should not be used on this
saw.
English
FIG. 15
FIG. 16
ON-OFF
SWITCH
PADLOCK
INSERTION
HOLE
SCREWS
FINE ADJUST KNOB
FIG. 17
6
7
English
Kickback
Kickback is a dangerous condition! It is caused by the work-
piece binding against the blade. The result is that the work-
piece can move rapidly in a direction opposite to the feed
direction. During kickback, the workpiece could be thrown
back at the operator. It can also drag the operator’s hand
back into the blade if the operator’s hand is at the rear of the
blade. If kickback occurs, turn the saw OFF and verify the
proper functioning of the splitter, anti-kickback teeth and
guards before resuming work.
CAUTION:
1. Always use the guard and make certain it is in good
working order. The guard’s splitter helps prevent binding
and the anti-kickback teeth on each side of the splitter
minimize the possibility of kickback. Use extra caution
until the workpiece is through the splitter and has
engaged anti-kickback teeth.
2. Do not saw warped, bowed or cupped wood. The work-
piece must have one straight, smooth side to go against
the rip fence or miter gauge. The workpiece must sit flat
on the table without rocking.
3. Do not cut “freehand”. Always use either the rip fence or
the miter gauge. Never use both.
4. Use extra care when the guard assembly cannot be
used (during dadoing or molding).
5. Support large workpieces carefully. Allowing them to
sag or droop can cause kickback.
Operation
Plain sawing includes ripping and cross cutting, plus a few
other standard operations of fundamental nature. The fol-
lowing methods feature safety. As with all power tools
respecting the tool, using caution and following safe prac-
tices will considerably lessen the possibility of personal
injury. However, if normal safety precautions are overlooked
or completely ignored, personal injury to the operator can
result. Read and follow all warnings indicated on the saw.
Through sawing is any operation which renders the materi-
al into two separate pieces.Observe the safety rules includ-
ed in this manual.
THIS SAW IS NOT INTENDED FOR CUTTING METAL.
Operating Instructions
There are two basic types of cuts: ripping and crosscutting.
In general, cutting with the grain is ripping and across the
grain is crosscutting. However, with man made materials
this distinction is somewhat difficult to make. Therefore, cut-
ting a piece of wood to a different width is ripping and cut-
ting across the short dimension is crosscutting. Neither rip-
ping or crosscutting may be done safely freehand! Ripping
requires the use of the rip fence and crosscutting uses the
miter gauge.
CAUTION: Before using the saw each and every time
verify the following:
1. Blade is tight.
2. Bevel angle lock knob is tight.
FIG. 20
WARNING
FIG. 19
POINTER
SCREW
BEVEL STOP
SCREW
BEVEL
STOP CAM
PUSH STICK
FIG. 23
FIG. 22
FIG. 21
STOP PLATE
LOCK HANDLE
ADJUSTING
SCREW
NUT
FIG. 18
BELVILLE
WASHERS
GAP
NUT
8
3. If ripping, ensure rail lock lever is tight and fence is par-
allel to the blade.
4. If crosscutting, miter gauge lever is tight.
5. Guard is in place and working properly.
6. Safety glasses are being worn.
7. The blade guard is properly attached and the anti-kick-
back teeth are functioning.
Failure to adhere to these common safety rules can greatly
increase the likelihood of injury.
Ripping
1. Lock the rip fence by pressing the rail lock lever down.
Remove the miter gauge.
2. Raise the blade so it is about 1/8"(3.2mm) higher than
the top of the workpiece.
3. Hold the workpiece flat on the table and against the
fence. Keep the workpiece about 1" (25.4mm) away
from the blade.
CAUTION: The workpiece must have a straight edge
against the fence and must not be warped, twisted or
bowed. Keep both hands away from the blade and away
from the path of the blade.
4. Turn the saw on and allow the blade to come up to
speed. Both hands can be used in starting the cut.
When there is approximately twelve (12) inches
(305mm) left to be ripped…use only one hand, with your
thumb pushing the material, your index and second fin-
ger holding the material down and your other fingers
hooked over the fence. Always keep your thumb along
side your first two fingers and near the fence.
5. Keeping the workpiece against the table and fence,
slowly feed the workpiece rearward all the way through
the saw blade. Continue pushing the workpiece until it is
clear of the guard and it falls off the rear of the table. Do
not overload the motor.
6. Never try to pull the workpiece back with the blade turn-
ing. Turn the switch off, allow the blade to stop, raise the
anti-kickback teeth on each side of the splitter if neces-
sary and slide the workpiece out.
7. When sawing a long piece of material or a panel, always
use a work support. A sawhorse, rollers, or out feed
assembly provides adequate support for this purpose. The
work support must be at the same height as the saw
table.
CAUTION: Never push or hold onto the “free” or “cut off”
side of the workpiece.
Bevel Ripping
This operation is the same as ripping except the bevel angle
is set to an angle other than zero degrees.
WARNING: Before connecting the table saw to the power
source or operating the saw, always inspect the guard and
splitter for proper alignment and clearance with saw blade.
Check alignment after each change of bevel angle.
Ripping Small Pieces
It is unsafe to rip small pieces. It is not safe to put your hands
close to the blade. Instead, rip a larger piece to obtain the
desired piece. When a small width is to be ripped and the
hand cannot be safely put between the blade and the rip
fence, use one or more push sticks. A pattern is included on
page 9 to make push sticks. Use them to hold the workpiece
against the table and fence, and push the workpiece fully
past the blade. See Figure 22.
Crosscutting
1. Remove the rip fence and place the miter gauge in the
desired slot.
2. Adjust the blade height so that the blade is about 1/8"
(3.2mm) higher than the top of the workpiece.
3. Hold the workpiece firmly against the miter gauge with
the path of the blade in line with the desired cut location.
Keep the workpiece an inch or so in front of the blade.
KEEP BOTH HANDS AWAY FROM THE BLADE AND
THE PATH OF THE BLADE.
4. Start the saw motor and allow the blade to come up to
speed.
5. While using both hands to keep the workpiece against
the face of the miter gauge, and holding the workpiece
flat against the table, slowly push the workpiece through
the blade. See Figure 23.
6. Never try to pull the workpiece with the blade turning.
Turn the switch off, allow the blade to stop, and carefully
slide the workpiece out.
CAUTION: Never touch or hold onto the “free” or “cut off”
end of the workpiece.
Bevel Crosscutting
This operation is the same as crosscutting except that the
bevel angle is set to an angle other than 0°.
WARNING: Before connecting the table saw to the power
source or operating the saw, always inspect the guard and
splitter for proper alignment and clearance with saw blade.
Check alignment after each change of bevel angle.
Mitering
This operation is the same as crosscutting except the miter
gauge is locked at an angle other than 0°. Hold the work-
piece FIRMLY against the miter gauge and feed the work-
piece slowly into the blade (to prevent the workpiece from
moving). See Figure 23.
MITER GAUGE OPERATION
To set your miter gauge, loosen the lock handle and move
the miter gauge to the desired angle. The miter gauge has
set stops and 90° and 45° left and right. To rotate the miter
gauge beyond these stops, flip the stop plate up, as shown
in Figure 21.
Compound Mitering
This is a combination of bevel crosscutting and mitering.
Follow the instruction for both bevel crosscutting and
mitering.
English
Dado Cutting
CAUTION: Do not attempt to stack dado blades thicker
than 13/16" (20mm). Do not use dado blades larger than 8"
(200mm) diameter. When installing the dado stack, do not
include the inner clamp washer. Replace it with the outer
clamp washer, then install the blade stack, arbor nut, and
tighten with the wrench supplied.
Since dado cuts are not through cuts, the cuts must be per-
formed with the blade guard removed. To remove the blade
guard, loosen the two bolts shown in Figure 10 and remove
the guard assembly.
When using the dado, the special dado insert (also sold as
an accessory) must be used.
Anytime a cut is required that is considerably wider than the
saw kerf, a dado is used. A dado cut is commonly used to
add support and line up a shelf for a cabinet, bookcase or
some such project. When using the dado, the guard must be
removed. Use EXTREME care when using the dado without
the guard. If a deep cut is required. Use several successive
FIG. 24
FIG. 25
DUST ACCESS
DOOR
HAIR PIN COTTERS
HEIGHT
ADJUSTMENT
THREADS
passes rather than attempting to make it with one pass.
Maximum dado width on this saw is 13/16" (20mm). DO
NOT USE WIDER COMBINATIONS.
CAUTION: Always check dado blade clearance before
plugging in the saw.
Be sure to place the guard and standard throat plate back in
position and check adjustments when the dado cuts are
complete.
Dust Collection
Your table saw is equipped with a dust shroud and dust col-
lection port. For best results, connect a vacuum to the port
at the rear of the saw.
If the saw is operated without a vacuum attached, most of
the dust will be blown out the dust collection port. However,
some dust will fall inside the base. If the saw is used on a
table or other surface without an opening on the bottom,
clean out the base and accumulated saw dust after each
cut.
After extended use, the saw’s dust collection system may
become clogged. To clear the dust collection system:
a) Unplug the saw.
b) Turn the saw on its side, so the bottom, open part of the
unit is accessible.
c) Open the dust access door shown in Figure 24 by
removing the two hair pin cotters shown. Clean out the
excess dust, and re-secure the access door with the hair
pin cotters.
When cutting wet wood without a vacuum or when cutting
with a dado blade, removing the dust access door may be
helpful in preventing clogs.
Lubrication
1. All motor bearings are permanently lubricated at the fac-
tory and no additional lubrication is needed.
2. The height adjustment screw may require periodic
cleaning and lubrication. If you have difficulty raising or
lowering the blade:
a) Unplug the saw.
b) Turn the saw on its side, so the bottom, open part of
the unit is accessible.
c) Clean and lubricate the height adjustment screws
threads on the underside of your saw with general
purpose grease, shown in Figure 25.
Accessories
Recommended accessories for use with your tool are avail-
able at extra cost from your distributor or local service center.
D
EWALT manufactures the following accessories for your
saw:
Portable Saw Stand
Outfeed Side Support
Replacement Throat Plate
Dado Throat Plate
CAUTION: The use of any non-recommended accesso-
ry may be hazardous.
If you need assistance in locating any accessory, please
contact D
EWALT Industrial Tool Co., 701 East Joppa Road,
Baltimore, MD 21286 or call 1-800-4-D
EWALT (1-800-433-
9258).
Cleaning
Use only mild soap and damp cloth to clean the tool. Never let
any liquid get inside the tool; never immerse any part of the tool
into a liquid. Never use solvents to clean saw or guard
components.
Important
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (including brush inspection
and replacement) should be performed by authorized ser-
vice centers or other qualified service organizations, always
using identical replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of war-
ranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
EWALT (1-800-433-
9258). This warranty does not apply to accessories or dam-
age caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you
may have other rights which vary in certain states or
provinces.
In addition to the warranty, D
EWALT tools are covered by
our:
1 YEAR FREE SERVICE
D
EWALT will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year
after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your DEWALT Power Tool, Laser, or Nailer for any reason,
you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-D
EWALT
for a free replacement.
9
English
Loading...
+ 24 hidden pages