Desa 32003 User Manual
ELECTRIC NAILGUN
Model 32003
OPERATING
INSTRUCTIONS
®
G 028
Safety Information
!
WARNING
Follow all safety precautions outlined in these operating instructions. Improper use of this tool can cause severe injury or death
from fire, electrical shock, or firing nail into body.
Before Operating Tool
1. Read and understand these operating instructions before operating tool.
2. Only well-instructed adults should operate tool. Never allow children to operate tool.
3. Do not operate tool
• where highly flammable liquids or gases are present
• while under the influence of alcohol, medication, or drugs
• if exposed to rain or in damp or wet areas
• while tired or in a hurry
• if tool is damaged
• if trigger does not turn tool on and off. Have faulty switch replaced by factory
service center.
4. Make sure tool is grounded while in use. This will protect the operator from
electrical shock. This tool has a three-wire cord and a three-prong, grounded
plug. Only connect tool to a three-prong, grounded outlet. The green (or green
and yellow) wire in the cord is the grounding wire. Never connect the grounding
wire to a live terminal. If you have a two-prong outlet, use an adapter (see Figure
1). Attach the green-colored lug (extending from the adapter) to a permanent
ground. You can attach lug to a properly grounded outlet box with a metal screw
(see Figure 1).
Cover of
Grounded
Outlet Box
Adapter
Metal
Grounding
Pin
Green Colored Lug
(Grounding Means)
Figure 1
5. Use only three-prong, grounded extension cords marked for outdoor use.
6. Never use this tool
• where heavy-duty tool is needed
• where not intended - for example - don’t use tool on concrete, metal, or glass
7. Wear snug-fitting clothing when operating tool. Do not wear loose clothing or
jewelry. They can get caught in moving parts.
8. Wear the following safety gear when operating tool.
• rubber gloves and footwear with non-skid soles (outdoors)
• eye protection conforming to ANSI Z87-1 and OSHA regulations. Make sure
anyone in the vacinity of tool wears eye protection.
• hair covering to contain long hair
Screw
2
9. Keep work area well lit.
10.Move trigger lock to the OFF position and unplug tool
• when loading tool
• when not in use
• when moving from one place to another
• before maintenance
• when changing accessories
11.Do not alter this tool in any way. Only use accessories designed for this tool.
During Operation of Tool
1. Keep all parts of body away from nail opening on tool.
2. Never point tool at anyone.
3. Keep children, animals, and bystanders away from tool and extension cord at all
times. Only tool user should be in work area.
4. Stay alert. Use common sense while operating tool.
5. Keep trigger lock in the OFF position and finger off trigger until ready to drive nail.
6. Keep work area clean. Cluttered work areas invite injuries.
7. Secure work before using tool. Use both hands to operate tool.
8. Do not touch any metal part of tool when nailing into areas where electrical wiring
may be present. These areas include walls, floors, and ceilings. If nail contacts
electrical wire, electric shock may occur.
9. Avoid body contact with grounded objects such as pipes, fences, and metal posts.
10.Do not force tool. Use tool at rate for which it was designed.
11.Do not overreach. Keep proper footing and balance at all times.
12.Carry tool from one place to another
• with tool unplugged
• with trigger lock in the OFF position
• with finger off the trigger
General
1. Inspect tool before and after each use. Check tool closely if it has been damaged.
Check for any damage that may affect operation of tool. Check for alignment or
binding of moving parts. Check for broken or damaged parts. Do not use tool if
damage affects operation. Have damage repaired by factory service center.
2. When servicing, use only identical replacement parts.
3. Maintain tool with care.
• Never fire tool when empty of nails. This may damage tool.
• Keep tool clean.
• Keep handles dry, clean, and free of oil and grease.
• Inspect power cord often. If damaged, have repaired by factory service center.
• Never carry tool by power cord.
• Never yank power cord to unplug it.
• Keep power cord away from heat, oil, and sharp edges.
• Inspect extension cords often and replace if damaged.
• Never oil or grease any part of tool.
4. Always store tool
• with nails removed from chamber
• out of children’s reach
• in a high or locked place that is dry
Keep these operating instructions for reference. It is your guide to safe and proper
operation of this tool.
3
Loading...