Page 1
CONTENTS
1. FUNDAMENTAL SAFETY WARNINGS .............7
2. SAFETY WARNINGS ....................................8
2.1 Symbols used in this Instruction for Use ........8
2.2 Designated use ..............................................8
2.3 Instruction for Use .........................................8
3. INTRODUCTION ..........................................8
3.1 Letters in brackets .........................................8
3.2 Troubleshooting and repairs ..........................8
3.3 Download the App! .......................................8
4. DESCRIPTION.............................................9
4.1 Description of the appliance (page 3 - A) ......9
4.2 Description of the homepage (main screen )
(page 2 - B) ...................................................9
4.3 Description of the accessories ........................9
4.4 Description of the milk container ..................9
4.5 "Mix carafe" description ...............................9
5. BEFORE USE...............................................9
5.1 Checking the appliance .................................9
5.2 Installing the appliance .................................9
5.3 Connecting the appliance ............................10
5.4 Setting up the appliance .............................10
6. TURNING THE APPLIANCE ON....................10
7. TURNING THE APPLIANCE OFF ..................10
8. MENU SETTINGS ...................................... 11
8.1 Rins
ing .............................................................11
8.2 Descaling ....................................................11
8.3 Water lter .................................................11
8.4 Beverages settings .....................................11
8.5 Adjust time .................................................11
8.6 Auto-start ..................................................12
8.7 Auto-o (standby) .....................................12
8.8 Cup warmer ................................................12
8.9 Energy saving .............................................12
8.10 Coee temperature ....................................12
8.11 Water hardness ..........................................12
8.12 Selecting the language ..............................12
8.13 Beep ...........................................................12
8.14 Cup light .....................................................13
8.15 Background ................................................13
8.16 Bluetooth ...................................................13
8.17 Emptying the circuit ...................................13
8.18 Default values .............................................14
5.1 Statistics .....................................................14
9. MAKING COFFEE .......................................14
9.1 Selecting the coee aroma ..........................14
9.2 Selecting the coee quantity ......................14
9.3 Making coee using coee beans ...............14
9.4 Making coee using pre-ground coee .......15
9.5 Adjusting the coee mill .............................15
9.6 Tips for a hotter coee.................................15
10. MAKING CAPPUCCINOS AND MILKBASED
COFFEES .................................................. 15
10.1 Filling and attaching the milk container ......16
10.2 Adjusting the amount of froth .....................16
10.3 Making cappuccinos and milk-based coees
automatically ..............................................16
10.4 Cleaning the milk container after use .........16
11. TEA FUNCTION ......................................... 17
12. DELIVERING HOT WATER ..........................17
13. STEAM DELIVERY ..................................... 17
13.1 Tips for using steam to froth milk ................18
13.2 Clean the hot water/steam spout after use .18
14. MAKING HOT CHOCOLATE .........................18
15. MAKING COLD BEVERAGES ........................ 19
15.1 Making cold coee ......................................19
15.2 Making cold milk froth ................................20
16. CUSTOMISING THE BEVERAGES ................20
17. MEMORISING YOUR PERSONAL PROFILE .... 21
18. CLEANING................................................ 21
18.1 Cleaning the machine .................................21
18.2 Cleaning the machine's internal circuit .......21
18.3 Cleaning the coee grounds container ........22
18.4 Cleaning the drip tray ..................................22
18.5 Cleaning the inside of the coee machine ..22
18.6 Cleaning the water tank ..............................22
18.7 Cleaning the coee spouts .........................23
18.8 Cleaning the pre-ground coee funnel .......23
18.9 Cleaning the infuser ....................................23
18.10 Cleaning the milk container ........................23
18.11 Cleaning the hot water/steam connection
nozzle..........................................................24
18.12 Cleaning the "Mix Carafe" (E) ......................24
19. DESCALE ..................................................24
20. SETTING WATER HARDNESS ...................... 25
20.1 Measuring water hardness ..........................25
20.2 Setting water hardness ...............................26
21. WATER SOFTENER FILTER ......................... 26
21.1 Installing the lter ......................................26
21.2 Replacing the lter ......................................26
21.3 Removing the lter .....................................27
22. TECHNICAL DATA ...................................... 27
23. DISPOSING OF THE APPLIANCE ................. 27
24. DISPLAYED MESSAGES .............................. 28
25. TROUBLESHOOTING ................................. 33
26. ELECTRICAL REQUIREMENTS..................... 36
6
Page 2
1. FUNDAMENTAL SAFETY WARNINGS
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Never clean by immersing the appliance in water.
• This is an household appliance only. It is not intended to be used in: sta kitchen areas in
shops, oces and other working environments; farm houses; by clients in hotels, motels
and other residential type environments; bed and breakfast type environments.
• If the plug or power cord is damaged, it must be replaced by customer services only to
avoid all risk.
FOR EUROPEAN MARKETS ONLY:
• This appliance can be used by children aged from 8 years and above if they have been
given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. User cleaning and maintenance shall not be made
by children unless they are above 8 years old and supervised. Keep the appliance and
power cord away from children under 8 years of age.
• The appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised or have been given
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
• Children shall not play with the appliance.
• Always unplug the appliance when left unattended and before assembly, taking apart
or cleaning.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).
7
Page 3
2. SAFETY WARNINGS
2.1 Symbols used in this Instruction for Use
Important warnings are identied by these symbols. It is vital to
respect these warnings.
Danger!
Failure to observe the warning may result in life threatening injury by electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note:
This symbol identies important advice or information for the
user.
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore follow these safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only. Never pull the cord as
you could damage it.
• To disconnect the appliance completely you must unplug it
from the mains socket.
• If the appliance is faulty, do not attempt to repair. Turn it
o, unplug from the mains socket and contact Customer
Services.
• Before cleaning the appliance, turn it o, unplug from the
mains socket and allow to cool.
Important:
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, the cup shelf (A11) could
become very hot.
Any other use is considered improper and thus dangerous. The
manufacturer is not liable for damage deriving from improper
use of the appliance.
2.3 Instruction for Use
Read this Instruction for Use carefully before using the appliance. Failure to follow this Instruction for Use may result in burns
or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Please note:
Keep this Instruction for Use. If the appliance is passed to other
persons, they must also be provided with this Instruction for Use.
3. INTRODUCTION
Thank you for choosing this bean to cup espresso and cappuccino
machine.
Take a few minutes to read this Instruction for Use. This will avoid
all risks and damage to the appliance.
3.1 Letters in brackets
The letters in brackets refer to the legend in the description of
the appliance on pages 2-3.
3.2 Troubleshooting and repairs
In the event of problems, rst try and resolve them by reading
the information given in sections “24. Displayed messages” and
“25. Troubleshooting”.
If this does not resolve the problem or you require further information, you should consult Customer Services by calling the
number given on the annexed "Customer Service" sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee. If repairs are required, contact
De’Longhi Customer Services only. The addresses are given in the
guarantee certicate provided with the machine.
3.3 Download the App!
2.2 Designated use
This appliance is designed and made to prepare coee, milk,
chocolate and hot water and to heat beverages.
A number of functions can be controlled remotely using the
De’Longhi Coee Link App.
8
Page 4
In the App, you can also nd information, tips and curious facts
about the world of coee, together with information on your
machine at your ngertips.
B10. : scroll arrow
B11. Customisable proles (see “17. Memorising your personal
prole”)
This symbol highlights the functions you can control or
consult using the App.
You can also create up to 6 new beverages for each prole and
save them in your appliance.
Please note:
Check compatible devices on "compatibledevices.delonghi.com".
4. DESCRIPTION
4.1 Description of the appliance (page 3 - A)
A1. Beans container lid
A2. Pre- ground coee funnel lid
A3. Beans container
A4. Pre- ground coee funnel
A5. Grinding adjustment dial
A6. Cup warmer shelf
A7. button: to turn the appliance on and o (standby)
A8. Coee spouts (adjustable height)
A9. Hot water and steam connection nozzle
A10. Coee grounds container
A11. Cup tray
A12. Drip tray water level indicator
A13. Drip tray grille
A14. Drip tray
A15. Water tank lid
A16. Water tank
A17. Water softener lter housing
A18. Infuser door
A19. Infuser
A20. Power cord connector socket
A21. Main switch (ON/OFF)
4.3 Description of the accessories
(page 2 - C)
C1. "Total Hardness Test" indicator paper (attached to page 2 of
the English instructions)
C2. Pre-ground coee measure
C3. Descaler
C4. Water softener lter (certain models only)
C5. Cleaning brush
C6. Hot water/steam spout
C7. Spout release button
C8. Power cord
C9. Ice cube tray (2 pieces)
4.4 Description of the milk container
(page 2 - D )
D1. Froth adjustment and CLEAN dial
D2. Milk container lid
D3. Milk container
D4. Milk intake tube
D5. Frothed milk spout (adjustable)
4.5 "Mix carafe" description
(page 2 - E )
E1. Lid
E2. Funnel
E3. Steam spout ("choco" accessory)
E4. Choco stirrer ("choco" accessory)
E5. "Mix carafe"
E6. Funnel release slide
E7. Aero stirrer ("aero" accessory)
4.2 Description of the homepage (main screen )
(page 2 - B)
B1. : menu to customise the beverages settings
B2. : appliance settings menu
B3. Selected aroma
B4. Clock
B5. Selected quantity
B6. : aroma selection
B7. : quantity selection
B8. : scroll arrow
B9. Beverages available for selection (press the or
scroll arrows to display all the beverages, the bottom bar
indicates which screen you are viewing)
5. BEFORE USE
5.1 Checking the appliance
After removing the packaging, make sure the product is complete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De’Longhi
Customer Services.
5.2 Installing the appliance
Important!
When you install the appliance, you should respect the following
safety warnings:
• The appliance gives o heat. After positioning the appliance on the worktop, leave a space of at least 3 cm between
9
Page 5
the surfaces of the appliance and the side and rear walls
and at least 15 cm above the coee maker.
• Water penetrating the appliance could cause damage.
• Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cord in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces (e.g.
electric hot plates).
5.3 Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to a correctly installed and eciently
earthed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
electrician.
5.4 Setting up the appliance
Please note!
• Coee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coee
in the mill. The machine is, however, guaranteed to be new.
• You should customise water hardness as soon as possible
following the instructions in section “20. Setting water
hardness”.
1. Plug the power cord (C8) connector into the socket (A20) at
the back of the appliance and connect the appliance to the
mains electricity supply (g. 1). Make sure the main switch
(A21) at the back of the appliance is pressed (g. 2);
2. "SELECT LANGUAGE": press (B10) or
ag corresponding to the required language appears on
the display (B), then press the ag;
Follow the instructions indicated on the appliance display:
3. "FILL TANK WITH FRESH WATER": remove the water tank
(A16) (g. 3), open the lid (A15) (g. 4), ll to the MAX line
(marked on the inside of the tank) with fresh water (g. 5),
close the lid and put the tank back in the appliance (g. 6);
4. "INSERT WATER SPOUT": Check that the hot water/steam
spout (C6) is inserted on the connection nozzle (A9) (g.
7) and place a container holding a minimum of 100 ml underneath (g. 8);
5. "WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS" appears on the display;
(B8)
until the
6. Press " " to conrm. The appliance delivers water
from the spout (g. 8) then goes o automatically.
The coee machine is now ready for normal use.
Please note!
• The rst time you use the appliance, you need to make 4-5
cappuccinos before it starts to give satisfactory results.
• The rst time you use the machine, the water circuit is
empty and the appliance could be very noisy. The noise
becomes less as the circuit lls.
• When making the rst 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
• To improve the performance of your appliance, we recommend installing a water softener lter (C4) as described
in section “21. Water softener lter”. If your model is not
provided with a lter, you can request one from De'Longhi
Customer Services.
6. TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch
(A21) is pressed (g. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appliance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
(A8) and is collected in the drip tray (A14) underneath. Avoid
contact with splashes of water.
• To turn the appliance on, press the button (A7-g.
9). The message "HEATING UP UNDERWAY PLEASE WAIT"
appears on the display.
• When heating is complete, the message changes to: "RINS
ING UNDERWAY, HOT WATER FROM SPOUTS". As well as
heating the boiler, this also heats the internal circuits by
circulating hot water.
The appliance is at temperature when the main screen (homepage) appears.
7. TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts
(A8). Avoid contact with splashes of water.
• To turn the appliance o, press the button (A7-g.
9).
10
Page 6
• The message "TURNING OFF, PLEASE WAIT" is displayed,
then the appliance performs a rinse cycle and goes o
(standby).
Please note!
If you will not be using the appliance for some time, rst empty
the water circuit (see section “8.17 Empt ying the circuit i”), then
unplug from the mains socket as follows:
• rst turn the appliance o by pressing the button
(g. 9);
• release the main switch (A21) at the back of the appliance
(g. 2).
Important!
Never press the main switch while the appliance is on.
8. MENU SETTINGS
8.1 Rins
Use this function to deliver hot water from the coee spouts (A8)
and hot water/steam spout (C6), if inserted, to clean and heat
the appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coee and hot water spouts (g. 8).
To enable the function, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
3. Press " " to start rinsing.
Do not leave the appliance unattended while hot water is being
delivered.
4. After a few seconds, hot water is delivered rst from the
5. To stop rinsing, press " " or wait for rinsing to
• If the appliance is not used for more than 3-4 days, when
• After cleaning, it is normal for the grounds container (A10)
ing
(B8)
until " RINSING" appears
on the display (B);
Important! Danger of burns.
coee spouts, then from the hot water/steam spout (if
inserted) to clean and heat the appliance’s internal circuit.
"RINSING UNDERWAY, HOT WATER FROM SPOUTS" appears
on the display, together with a progress bar which lls
gradually as preparation proceeds;
stop automatically.
Please note!
you turn it on again, we strongly recommend performing
2/3 rinses before use;
to contain water.
8.2 Descaling
For instructions on descaling, see section “19. Descale”.
8.3 Water lter
For instructions on how to install the lter (C4), see section “21.
Water softener lter”.
8.4 Beverages settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage, except cold
coee, cold milk and chocolate.
1. Press " " (B2) to enter the menu;
2. Press (B10) or
appears on the display (B);
3. Press " ". The values for the rst beverage appear on the
display;
4. The reference user prole is highlighted on the display. The
values are displayed on vertical bars. The default value is
indicated by the symbol, while the current value is
highlighted by the solid part of the vertical bar;
5. To go back to the settings menu, press " ".
To scroll and display the beverages, press " ";
6. To reset the default values for the beverage displayed, press
" RESET";
7. "CONFIRM RESET?": to conrm, press " " (to cancel,
press " ");
8. "DEFAULT VALUES SET": press " ".
The beverage has been reset to the default values. Continue with
the other beverages, or go back to the settings menu.
Please note!
• To change the beverages in another prole, go back to the
homepage, select the required prole (B11) and repeat the
procedure.
• To reset all the beverages in the prole, see section “8.18
Default values
• ”
(B8)
until " DRINKS SETTINGS"
8.5 Adjust time
To adjust the time on the display (B), proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
on the display (B);
3. Press " ". The time setting panel appears on the display;
4. Press or corresponding to the hours and minutes
until the current time is displayed;
5. To conrm, press " " (to cancel, press " "),
then press " " to go back to the homepage.
The time is now set.
(B8)
until " SET TIME" appears
11
Page 7
8.6 Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly
(see section “8.5 Adjust time ”).
To enable auto-start, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
pears on the display (B);
3. Select the function by pressing " ". The time setting
panel appears on the screen;
4. Press or corresponding to the hours and minutes
until the required auto-start time is displayed;
5. Press or to enable or disable
auto-start.
6. To conrm, press " " (or cancel and go back to
the settings menu by pressing " "), then press "
" to go back to the homepage.
The auto-start time is now set and the corresponding symbol is
displayed to indicate that the function has been enabled.
Please note!
When the appliance is turned o using the main switch (A21),
the auto-start setting (if enabled) is lost.
(B8)
until " AUTOSTART" ap-
8.9 Energy saving
Use this function to enable or disable energy saving. When enabled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable "Energy Saving", proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
appears on the display (B);
3. Press " " to enable- or disable-
energy saving.
4. Press " " to go back to the homepage.
The corresponding symbol appears on the display alongside the
time to indicate that the function has been enabled.
(B8)
until " ENERGY SAVING"
8.10 Coee temperature
To modify the temperature of the water used to make the coee,
proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
TURE" appears on the display (B) together with the current
selection (LOW, MEDIUM, HIGH or MAXIMUM);
3. Press " " to select the required temperature;
4. Press " " to go back to the homepage.
Please note!
A dierent temperature can be set for each prole (see section
“17. Memorising your personal prole”).
(B8)
until " COFFEE TEMPERA-
8.7 Auto-o (standby)
Auto-o can be set so that the appliance goes o after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-o, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
on the display (B), together with the current selection (15
or 30 minutes, or 1, 2 or 3 hours);
3. Press " " on the display to select the required value;
4. Press " " to go back to the homepage.
Auto-o is now programmed.
(B8)
until " AUTO-OFF" appears
8.8 Cup warmer
To warm the cups before making coee, you can enable the cup
warmer (A6) and rest the cups on the shelf.
1. Press " " (B2) to enter the menu;
2. Press (B10) or
pears on the display (B);
3. Press " " to enable- or disable- the
cup warmer.
4. Press " " to go back to the homepage.
(B8)
until " CUP WARMER" ap-
8.11 Water hardness
For instructions on setting water hardness, see section “20. Setting water hardness”.
8.12 Selecting the language
To modify the language of the display (B), proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
appears on the display;
3. Press " " : press or to display and select the
ag corresponding to the required language;
4. Press " " twice to go back to the homepage.
(B8)
until " SET LANGUAGE"
8.13 Beep
This enables or disables the beep emitted by the machine each
time an icon is pressed or an accessory is inserted/removed. To
disable or enable the beep, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
the display (B);
12
(B8)
until " BEEP" appears on
Page 8
3. Press " " to enable- or disable-
the beep;
4. Press " " to go back to the homepage.
8.14 Cup light
This function enables or disables the cup lighting.
The lights come on each time coee beverages or hot milk is delivered and during each rinse cycle.
To disable or enable this function, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
pears on the display (B);
3. Press " " to enable- or disable- the
cup lighting;
4. Press " " to go back to the homepage.
8.15 Background
You can choose the display background from the following 4
alternatives: "SHADED BLUE", "STAINLESS STEEL", "COFFEE
BROWN", "DARK BLUE". Proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
appears on the display (B);
3. Press " ". The available backgrounds appear on the
display;
4. Select the required background by pressing the chosen
panel. The appliance goes back to the settings menu with
the new background;
5. Press " " to go back to the homepage.
(B8)
until " CUP LIGHTING" ap-
(B8)
until " BACKGROUND"
8.16 Bluetooth
This function enables or disables the protection PIN to connect to
the appliance from a device.
1. Press " " (B2) to enter the menu;
2. Press (B10) or
on the display (B);
3. Press " " to access the function;
4. Enable or disable the PIN protection by pressing -
or ;
5. Press " " twice to go back to the homepage.
The preset PIN is "0000". You are recommended to customise the
PIN directly from the APP.
Please note!
The serial number of the appliance, visible in the "Bluetooth"
function, enables it to be identied unambiguously when an
association is created with the APP.
(B8)
until " BLUETOOTH" appears
8.17 Emptying the circuit
To avoid the water in the circuit freezing if the appliance is to be
left idle for a long period of time, or before taking it to customer
services, we recommend emptying the water circuit.
Proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
EMPTYING" appears on the display (B);
3. Press " ";
4. "EMPTY GROUNDS CONTAINER AND DRIP TRAY": extract and
empty the grounds container (A10) and drip tray (A14).
Press " ";
5. "INSERT GROUNDS CONTAINER AND DRIP TRAY": inser t
the drip tray complete with grounds container;
6. "PLACE 0.5l CONTAINER UNDER SPOUTS, PRESS OK TO
START": position a container under the coee spouts (A8)
and hot water spout (C6). Press " " (g. 8);
Danger of burns!
Do not leave the appliance unattended while hot water is being
delivered.
10. "INSERT WATER TANK, PRESS OK TO CONTINUE": insert the
water tank and press " " (g. 6);
11. "WATER CIRC. EMPTYING UNDERWAY": wait for the appliance to empty the circuit; (Important: hot water from the
spouts!). As the water circuit empties, the appliance could
become noisier. This is part of normal operation.
12. "EMPTY DRIP TRAY": remove, empty and reposition the drip
tray, then press " ";
13. "EMPTYING COMPLETE: PRESS OK TO TURN OFF": press "
". The appliance goes o.
Please note!
When turned on again, the appliance asks for the circuit to be
lled: follow the instructions from point 3 of section “5.4 Setting
up the appliance”.
13
(B8)
until " WATER CIRCUIT
7. "RINSING UNDERWAY,
PLEASE WAIT": the appliance performs a rinse
cycle from the coee
spouts;
8. "EMPTY WATER TANK":
extract the tank (A16)
and empty it completely,
then press " "
(g. 10);
9. (If the lter is installed)
10
"REMOVE WATER SOFTENER FILTER": remove the
lter from the tank. Press
" ";
Page 9
8.18 Default values
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as set).
To reset the default values, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
appears on the display (B). Press " ";
3. Press " RESET ALL" to reset all the proles to the original parameters, otherwise select the required prole;
4. "RESET DEFAULT VALUES": press " "
" to leave the parameters unaltered);
5. "DEFAULT VALUES RESET": press " " to conrm and
" " to go back to the homepage.
(B8)
until " DEFAULT VALUES"
to conrm (or "
5.1 Statistics
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
pears on the display (B);
3. Press " " to verify all the available statistics by pressing
or ;
4. Press " " to go back to the homepage.
(B8)
until " STATISTICS" ap-
9. MAKING COFFEE
9.1 Selecting the coee aroma
Select the required aroma from the homepage by pressing
" AROMA" (B6):
(see “9.4 Making coee
using pre-ground coee”)
X-LIGHT AROMA
LIGHT AROMA
MEDIUM AROMA
STRONG AROMA
X-STRONG AROMA
Custom (if programmed) /
Standard
After delivering the beverage, the aroma setting is reset to the
value.
9.2 Selecting the coee quantity
Select the required quantity of coee in the cup by pressing
" QUANTITY" (B7) from the homepage:
SMALL SIZE
MEDIUM SIZE
LARGE SIZE
EXTRA-LARGE SIZE
Custom quantity (if programmed) / Standard
quantity
After delivering the beverage, the quantity setting is reset to the
value.
9.3 Making coee using coee beans
Important!
Do not use caramelised or candied coee beans as they could
stick to the coee mill and make it unusable.
1. Fill the container (A3) (g. 12) with coee beans;
2. Place a cup under the coee spouts (A8);
3. Lower the spouts as near as possible to the cup (g. 13).
This makes a creamier coee;
4. Press (B10) or
displayed;
5. Then select your required coee from the homepage:
• ESPRESSO
• DOPPIO+
• COFFEE
6. Preparation begins. An image of the selected beverage appears on the display (B), together with a progress bar which
gradually lls as preparation proceeds.
Please note:
• You can prepare 2 cups of ESPRESSO coee at the same
time by pressing "2X " during preparation of 1 ESPRESSO (the image is displayed for a few seconds at the start of
preparation).
• While the machine is making coee, delivery can be interrupted at any moment by pressing " ".
• As soon as delivery has ended, to increase the quantity of
coee in the cup, just press " ". When the required quantity is reached, press " ".
Once the coee has been made, the appliance is ready to make
the next beverage.
(B8)
until the required coee is
• LONG
• AMERICANO
• 2X ESPRESSO
14
Page 10
Please note!
• Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
ETC.). Their meaning is explained in section “24. Displayed
messages”.
• For hotter coee, see section “9.6 Tips for a hotter coee”.
• If the coee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in sections “9.5
Adjusting the coee mill” and “25. Troubleshooting”.
• Preparation of each coee can be customised (see sections
“16. Customising the beverages E” and “17. Memorising
your personal prole”).
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the rst coee is delivered.
9.4 Making coee using pre-ground coee
Important!
• Never add pre-ground coee when the machine is o or it
could spread through the inside of the machine and dirty it.
This could damage the appliance.
• Never use more than 1 level measure (C2) or it could dirty
the inside of the coee machine or block the funnel (A4).
Please note!
If you use pre-ground coee, you can only make one cup of coffee at a time.
1. Press " AROMA" (B6) repeatedly until " " (preground) appears on the display (B).
2. Open the pre-ground coee funnel lid (A2).
3. Make sure the funnel (A4) is not blocked, then add one level
measure of pre-ground coee (g. 14).
4. Place a cup under the coee spouts (A8) (g. 13).
5. Then select your required coee (ESPRESSO, COFFEE, LONG,
AMERICANO);
6. Preparation begins. An image of the selected beverage appears on the display, together with a progress bar which
gradually lls as preparation proceeds.
Please note!
• While the machine is making coee, delivery can be interrupted at any moment by pressing " ".
• As soon as delivery has ended, to increase the quantity of
coee in the cup, just press " ". When the required quantity is reached, press " ".
Once the coee has been made, the appliance is ready to make
the next beverage.
Important! Making LONG coee :
Halfway through preparation, the message "ADD PREGROUND
COFFEE, MAXIMUM ONE MEASURE" IS DISPLAYED. Add one
level measure of pre-ground coee and press " ".
Please note!
• Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
ETC.). Their meaning is explained in section “24. Displayed
messages”.
• For hotter coee, see section “9.6 Tips for a hotter coee”.
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the rst coee is delivered.
9.5 Adjusting the coee mill
The coee mill is set by default to prepare coee correctly and
should not require regulating initially.
However, if after making the rst few coees you nd that the
coee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting the
grinding adjustment dial (A5 - g. 11).
Please note!
The grinding adjustment dial must only be turned when the
coee mill is in operation during the initial phase of coee
preparation.
If the coee is delivered too slowly or not
at all, turn one click clockwise towards 7.
For fuller bodied creamier coee, turn
one click anticlockwise towards 1 (do
not turn more than one click at a time
otherwise the coee could be delivered
a drop at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
9.6 Tips for a hotter coee
For hotter coee, you should:
• perform a rinse cycle by selecting the "Rinsing" function in the
settings menu (section “8.1 Rinsing ”);
• warm the cups with hot water using the hot water function
(see section “12. Delivering hot water”);
• increase the coee temperature in the settings menu (see
section “8.10 Coee temperature ”).
10. MAKING CAPPUCCINOS AND MILKBASED
COFFEES
Please note!
To avoid milk with poor froth or large bubbles, always clean the
milk container lid (D2) and hot water connection nozzle (A9) as
described in sections “10.4 Cleaning the milk container after
use”, “18.10 Cleaning the milk container” and “18.11 Cleaning
the hot water/steam connection nozzle”.
15
Page 11
10.1 Filling and attaching the milk container
1. Remove the lid (D2) (g. 15);
2. Fill the milk container (D3) with a sucient quantity of
milk, not exceeding the MAX level marked on the container (g. 16). Each mark on the side of the container corresponds to about 100 ml of milk;
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If "Energy Saving" mode is enabled, you may have to wait a
few seconds before the beverage is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (g. 17);
4. Place the lid back on the milk container;
5. If present, extract the hot water/steam spout (C6) by pressing the release button (C7) (g. 18);
6. Attach the milk container (D) to the connection nozzle (A9)
(g. 19) and push as far as it will go. The machine emits a
beep (if the beep function is enabled);
7. Place a suciently large cup under the coee spouts (A8)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(g. 20).
8. Follow the instructions below for each function.
10.2 Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coees.
Dial
position
Description Recommended for…
NO FROTH HOT MILK (not frothed) /
CAFFELATTE
MIN. FROTH LATTE MACCHIATO /
FLAT WHITE
MAX. FROTH CAPPUCCINO / CAPPUCCI
NO+ / CAPPUCCINO MIX
/ ESPRESSO MACCHIATO /
HOT MILK (frothed)
10.3 Making cappuccinos and milk-based coees
automatically
1. Fill the milk container (D) and attach it as described above.
2. Select the required beverage from the homepage:
• CAPPUCCINO • LATTE MACCHIATO
• CAFFELATTE
• HOT MILK
• CAPPUCCINO+
3. A message on the display (B) instructs you to turn the froth
adjustment dial (D1) according to the froth required by the
original recipe. Turn the dial on the milk container lid (D2)
and conrm the selection by pressing " ".
4. After a few seconds, preparation begins automatically and
an image of the selected beverage appears on the display,
together with a progress bar which gradually lls as preparation progresses.
Please note: general indications when preparing all
cappuccinos and milk-based coees
• " ": press to interrupt preparation completely and
go back to the homepage.
• " ": press to interrupt milk or coee delivery
and move on to the next delivery (if applicable) to complete the beverage.
• At the end of delivery, to increase the quantity of coee in
the cup, press " EXTRA".
• Preparation of each coee can be customised (see sections
“16. Customising the beverages ” and “17. Memorising
your personal prole”).
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
Once the coee has been made, the appliance is ready to make
the next beverage.
• ESPRESSO MACCHIATO
• FLAT WHITE
• CAPPUCCINO MIX
10.4 Cleaning the milk container after use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout (D5).
Avoid contact with splashes of water.
Each time you use a milk function, "TURN DIAL TO <CLEAN>
POSITION TO START CLEANING" appears on the display and the
milk frother lid must be cleaned:
1. Leave the milk container (D) in the machine (you do not
need to empty it);
2. Place a cup or other recipient under the frothed milk spout
(g. 20);
3. Turn the froth adjustment dial (D1) to "CLEAN" (g. 21).
"CLEANING MILK CONTAINER UNDERWAY PLACE A RECIPIENT UNDER MILK SPOUT" appears on the display (B) (g.
22) together with a bar which gradually lls as cleaning
proceeds. Cleaning stops automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the steam
connection nozzle (A9) with a sponge (g. 23).
16
Page 12
Please note!
• To prepare a number of cappuccinos and milk based coffees, clean the milk container after you have prepared
the last beverage only. To proceed with making the next
beverages, when the "CLEAN message is displayed, press
" ".
• If you do not clean the milk container, the symbol appears on the display to remind you that it needs cleaning.
• The milk container can be kept in the refrigerator.
• In some cases, to clean you must wait for the appliance to
heat up.
11. TEA FUNCTION
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached correctly to the hot water/steam connection nozzle (A9);
2. Put a tea bag in the cup, then place the cup under the spout
(as close as possible to avoid splashes);
3. Select " TEA FUNCTION" from the homepage;
4. "HOT WATER FOR"; select:
- the required quantity of water by pressing (g.
24);
- the required water temperature by pressing one of the
proposed teas; each tea (white, green, oolong or black)
corresponds to a specic water temperature (g. 25);
5. Once the beverage is selected, the corresponding image
appears on the display (B), together with a progress bar
which lls gradually as preparation proceeds;
6. The machine delivers the chosen quantity of hot water,
then delivery stops automatically. To stop delivery manually, press " ".
Please note!
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the hot water is delivered.
• The quantity of water in the cup can be customised (see
sections “16. Customising the beverages ” and “17. Memo-
rising your personal prole”).
• Delivery can be stopped at any moment by pressing "
";
• As soon as delivery has ended, to increase the quantity of
water in the cup, just press " EXTRA". When the required
quantity is reached, press " ".
12. DELIVERING HOT WATER
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached correctly to the hot water/steam connection nozzle (A9);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. Select “ HOT WATER” from the homepage. The corresponding image appears on the display (B), together with a
progress bar which lls gradually as preparation proceeds;
4. The machine delivers hot water, then delivery stops automatically. To interrupt hot water delivery manually, press
" ".
Please note!
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the hot water is delivered.
• Preparation of hot water can be customised (see sections
“16. Customising the beverages ” and “17. Memorising
your personal prole”).
13. STEAM DELIVERY
Important! Danger of burns.
Do not leave the appliance unattended while steam is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached correctly to the hot water/steam connection nozzle (A9);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Select “ STEAM” from the homepage. The corresponding image appears on the display (B), together with
a progress bar which lls gradually as preparation proceeds
and after a few seconds, steam to heat the liquid is delivered from the hot water/steam spout;
4. When the required temperature or level of froth is reached,
interrupt steam delivery by pressing " ";
Important!
Always stop steam delivery before extracting the container containing the liquid to avoid burns from splashes.
Please note!
If "Energy saving" is active, you may have to wait a few seconds
before steam is delivered.
17
Page 13
13.1 Tips for using steam to froth milk
BACK
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow movements in an upward direction.
• To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following section.
13.2 Clean the hot water/steam spout after use
Always clean the hot water/steam spout (C6) after use to avoid
the build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and deliver a little water (see section “12. Delivering hot water”).
Stop delivery of hot water by pressing " ".
2. Wait a few minutes for the hot water/steam spout to cool
down, then extract (g. 18) by pressing the release button
(C7). Hold the spout with one hand and with the other, turn
the hot water/steam spout and pull it downwards (g. 26).
3. Also remove the steam connection nozzle by pulling it
downwards (g. 27).
4. Check the hole in the connection nozzle is not blocked. If
necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
6. Insert the connection nozzle, then the cappuccino maker
on the nozzle by pushing it upwards and turning it clockwise until it is attached.
to the level. To make two cups or one mug of chocolate, pour the milk (or water) into the funnel up to the
level. When you have added the milk (or
water), press “ ”
(or press
BACK
“
” to go back
to the previous screen);
5. "ADD CHOCOLATE POWDER THROUGH THE FUNNEL (STEP
4 OF 5)" (g. 32): to make one cup of chocolate, add two
measures (C2) (25 g) of hot chocolate powder. To make two
cups or one mug of hot chocolate, add four measures of hot
chocolate powder. When you have added the hot chocolate
powder, press “ ”
(or press
BACK
“
” to go back
to the previous screen);
Important!
Make sure the hole in the funnel shown in g. 33 is clean.
Please note!
• The milk must be poured into the funnel when the steam
spout and stirrer are already in place. Do not exceed the
level marked on the carafe. Increase or
reduce the quantity of hot chocolate powder according to
taste.
• To use water instead of milk, follow the instructions for
milk.
• To prepare hot chocolate correctly, rst pour the milk (or
water) into the funnel, then add the hot chocolate or cocoa
powder.
14. MAKING HOT CHOCOLATE
Select CHOCOLATE from the homepage and proceed as follows:
1. "SELECT CUPS NUMBER AND DENSITY (STEP 1 OF 5)":
press the selection arrows to choose whether to pre-
pare 1 cup ( ) or 2 cups ( ) and
the required density (min= ; max =
),
then press " " to conrm
the selection and move on to the next step (or press
"
" to go back to the previous screen);
2. "ADD CHOCO STIRRER IN CARAFE (STEP 2 OF 5)": lift the carafe lid (E1) (g. 28), pull the release slide (E6) and extract
the carafe funnel (E2) (g. 28). Make sure the steam spout
(E3) and choco stirrer (E4) are in place (g. 29), then insert
the assembled funnel in the carafe (g. 30);
3. Press " " to move on to the next step
BACK
"
" to go back to the previous screen);
4. "POUR MILK OR WATER TO DESIRED LEVEL (STEP 3 OF 5)"
(g. 31): to make one cup of chocolate, pour milk at refrigerator temperature (or cold water) into the funnel up
(or press
34
6. "CLOSE LID AND INSERT CARAFE, PRESS OK TO START": Close
the lid (g. 34) and attach the carafe to the connection nozzle, pushing it as far as it will go (A9, g. 35). The machine
emits a beep (if the beep function is enabled);
7. Press “ ” to start the function; the appliance starts
mixing the hot chocolate powder then delivers steam to
heat it;
Please note!
• If the hot chocolate powder used does not contain thickener, adjusting the density will have no eect.
• To stop making chocolate, press " ".
18
35
Page 14
At the end of preparation, the appliance prepares to make the next
BACK
BACK
beverage. The chocolate is ready to be poured into the cup.
Danger of burns!
• While making the chocolate, the carafe and lid become
very hot. Hold by the handle only to remove the carafe and
pour the chocolate.
• While making the hot chocolate, it is normal for steam to
come out of the holes in the chocolate carafe lid.
• Heating the milk causes splashes inside the carafe. This is
normal.
• The quantity of hot chocolate in the cup varies according to
the density selected. The quantity is less with a high density than with a low density.
15. MAKING COLD BEVERAGES
15.1 Making cold coee
From the homepage, select " COLD COFFEE" and proceed
as follows:
1a. Making coee using coee beans: "CHOOSE AROMA
(STEP 1 OF 7)" (g. 36): select the required coee aroma
(for best results, we recommend selecting "X-STRONG
AROMA");
1b. Using pre-ground coee: Press " AROMA" (B6) re-
peatedly until " " (pre-ground) appears on the display
(B);
2. Press " " (or press "
previous screen);
3. "SELECT CUP SIZE AND FROTH QUANTITY (STEP 2 OF 7)"
(g. 37): select the quantity in the cup ("small" or "large")
and one of the froth levels ( min, med,
extra) using the arrows underneath. Then press "
"
(or press
"
Please note!
If you use pre-ground coee, you can only make "small" cups
of coee;
" to go back to the previous screen);
BACK
" to go back to the
4. "ADD AERO STIRRER IN CARAFE (STEP 3 OF 7)" (g. 38): lift
the carafe lid (E1) (g. 38), pull the release slide (E6) and
extract the carafe funnel (E2) (g. 38), then make sure the
aero stirrer (E7) is inserted and attach the assembled funnel to the carafe (g. 39);
Please note!
• To prepare the beverage correctly, make sure the steam
spout (E3) is not inserted.
• Never insert the "Mix Carafe" lid on the connection nozzle
(A9) without the carafe (E5) as direct contact with the stirrer in movement could be dangerous.
38
5. Press " " to move on to the next step
"
" to go back to the previous screen);
6. "ADD 9 (or 18) ICE CUBES AND SUGAR (STEP 4 OF 7)" (g.
40): add the ice cubes prepared with the mould (C9) provided and the right amount of sugar for the "small" or "large"
quantity, then press " "
go back to the previous screen);
(or press
"
39
(or press
BACK
" to
AROMA
36
37
40 41
7. "INSERT CARAFE UNDER COFFEE SPOUT (STEP 5 OF 7)" (g.
41): lift the coee spouts (A8) and position the carafe so
that the coee is delivered directly into the carafe (E): press
" " to start the function;
8. Coee is delivered into the carafe (g. 42). "ESPRESSO DE
LIVERY, X-STRONG AROMA" appears on the display with a
bar which gradually lls as preparation proceeds. Delivery
19
Page 15
stops automatically. To stop preparation manually, press
BACK
BACK
" ".
42
9. "CLOSE LID AND INSERT CARAFE, PRESS OK TO START" (g.
43). Extract the carafe (E), close the lid (E1) and attach the
carafe to the connection nozzle, pushing as far as it will go
(A9). Press " " to start the function. The appliance
starts mixing the coee and ice and "COLD COFFEE" appears
on the display (B) with a bar which gradually lls as prepa-
ration proceeds.
Preparation stops automatically.
"WANT TO CONTINUE MIXING?" appears on the display: press
"YES" until you obtain a satisfactory froth and/or until all the ice
has melted, then press " ". You can mix twice for a
maximum of about a minute.
Please note!
To interrupt mixing at any moment, press " " and,
when the "WANT TO QUIT PREPARATION?" prompt appears, conrm with "YES". If you press "NO", mixing resumes.
At the end of preparation, the appliance prepares to make the next
beverage. The cold coee is ready to be poured into the cup.
RECIPE FOR BEST RESULTS:
• ICE: add 9 ice cubes (45 g) for one cup or 18 cubes (90 g)
for 2 cups. We recommend using the tray (C9) provided, de-
signed to obtain ideal sized cubes;
• COFFEE: for a good cream/froth, use coee with a high
percentage of "robusta".
• SUGAR: use one teaspoon of sugar for each cup. We recom-
mend using castor sugar.
43
15.2 Making cold milk froth
From the homepage, select " MILK FROTH *" and proceed as follows:
1. "SELECT CUP SIZE AND FROTH QUANTITY STEP 1 OF 4"
(g. 37): select the quantity in the cup ("small" or "large")
and one of the froth levels ( min, med,
max): then press " "
back to the homepage);
2. "ADD AERO STIRRER IN CARAFE (STEP 2 OF 7)" (g. 39): lift
the carafe lid (E1) (g. 38), pull the release slide (E6) and
extract the carafe funnel (E2) (g. 38), then make sure the
aero stirrer (E7) is inserted and attach the assembled funnel to the carafe (g. 39);
44
"
" to go back to the previous screen);
5. "CLOSE LID AND INSERT CARAFE; PRESS OK TO START";
close the lid (E1) and attach the carafe to the connection
nozzle, pushing as far as it will go (A9);
6. Press " ": stirring begins and "COLD MILK FOAM "
appears on the display (B) with a bar which gradually lls
as preparation proceeds;
Preparation stops automatically.
Please note!
• To interrupt mixing manually at any moment, press "
" and conrm with "YES";
• At the end of preparation, "WANT TO CONTINUE MIXING?" is
displayed. Press "YES" until you obtain a satisfactory froth,
then press " ". You can mix twice for a maximum of about a minute. On the other hand, if the froth is
satisfactory at the end of preparation, press "NO".
(or press
3. Press " " to
move on to the next step
(
or press
go back to the previous
screen);
4. "POUR COLD MILK TO DESIRED LEVEL (STEP 3 OF
4)": (g. 44): add the right
amount of cold milk for
the quantity selected (100
ml small cup;
200 ml large cup), then
press " "
BACK
"
"
" to go
" to
(or press
16. CUSTOMISING THE BEVERAGES
The aroma (when required) and quantity of the beverages (apart
from cold coee and cold milk) can be customised.
1. Make sure the prole for which you want to customise the
beverage is active. You can select "MY" beverages for each
of the 6 proles;
2. From the homepage, press " " (B1);
3. To access the customising screen, choose the beverage you
want to customise. The corresponding accessories must be
inserted;
20
Page 16
4. (Beverages with coee only) "CHOOSE COFFEE AROMA":
Select the required aroma by pressing or and
press " ";
5. "CUSTOMISING COFFEE (OR WATER) QUANTITY, STOP TO
SAVE": Preparation begins and the appliance displays the
quantity customising screen in the form of a vertical bar.
The star alongside the bar represents the current quantity.
6. When the amount reaches the minimum quantity you can
set, " " is displayed.
7. When the required quantity in the cup is reached, press "
".
8. "SAVE NEW SETTINGS?": Press "YES" or "NO".
The appliance conrms if the values have been saved or not (depending on the previous selection). Press " ".
The appliance goes back to the homepage.
Please note!
• Cappuccino and milk-based coees: the coee aroma
is saved rst, followed by the quantity of rst milk, then
coee;
• Americano: the coee aroma is saved rst, followed by the
quantity of rst coee, then hot water;
• Hot water: the appliance delivers hot water. Press
" " to save the required quantity.
• You can also customise the beverages by connecting with
the DeLonghi Coee Link App.
• Press " " to exit programming. The values will not
be saved.
Beverage quantity table
Beverage Standard
quantity
ESPRESSO 40 ml 20-80 ml
LONG 160 ml 115-250 ml
COFFEE 180 ml 100-240 ml
DOPPIO+ 120 ml 80-180 ml
AMERICANO 150 ml 70-480 ml
TEA 150 ml 30-420 ml
HOT WATER 250 ml 20-420 ml
Programmable
quantity
17. MEMORISING YOUR PERSONAL PROFILE
The appliance allows you to memorise 6 dierent proles, each
associated with a dierent icon.
The customised "MY" beverages "AROMA" and "QUANTITY" values are saved in each prole (see section “16. Customising the
beverages ”). The order in which all the beverages are selected is based on the frequency of selection.
To select or enter a prole, press on the prole currently in use
(B11), press (B10) or
displayed, then press on the prole.
Please note!
• " GUEST" prole: select this prole to deliver beverages
with the default settings. The function is not active.
• You can rename your personal prole by connecting with
the DeLonghi Coee Link App.
To customise the prole icon, proceed as follows:
1. Select the prole (B11);
2. Select "Customise";
3. Press (B10) or
on the display (B), then select;
4. Conrm the selection with " . The appliance goes
back to the homepage.
(B8)
until the required prole is
(B8)
until the required icon appears
18. CLEANING
18.1 Cleaning the machine
The following parts of the machine must be cleaned regularly:
- the appliance’s internal circuit;
- coee grounds container (A10);
- drip tray (A14);
- water tank (A16);
- coee spouts (A8);
- pre-ground coee funnel (A4);
- infuser (A19), accessible after opening the infuser door
(A18);
- milk container (D);
- "Mix carafe" (E);
- hot water/steam connection nozzle (A9);
- touch screen (B).
Important!
• Do not use solvents, abrasive detergents or alcohol to clean
the coee machine. With De’Longhi superautomatic coee
machines, you need not use chemical products to clean the
machine.
• None of the components of the appliance can be washed in
a dishwasher with the exception of the milk container (D)
and "Mix carafe".
• Do not use metal objects to remove encrustations or coee
deposits as they could scratch metal or plastic surfaces.
18.2 Cleaning the machine's internal circuit
If the appliance is not used for more than 3/4 days, before using
it again, we strongly recommend switching it on and:
1. performing 2-3 rinse cycles by selecting the "Rinse" function (section “8.1 Rinsing ”);
2. delivering hot water for a few seconds (section “12. Delivering hot water”).
21
Page 17
Please note!
46
47
After cleaning, it is normal for the grounds container (A10) to
contain water.
18.3 Cleaning the coee grounds container
When "EMPTY GROUNDS CONTAINER" appears on the display
(B), the grounds container must be emptied and cleaned. The
appliance cannot be used to make coee until you have cleaned
the grounds container (A10). Even if not full, the empty grounds
container message is displayed 72 hours after the rst coee has
been prepared. For the 72 hours to be calculated correctly, the
machine must never be turned o with the main switch.
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray (A11) becomes hot. Wait for it to cool down before touching it and handle it from the front only.
To clean (with the machine on):
1. Remove the drip tray
(A14) (g. 45), empty and
clean.
2. Empty the grounds container (A10) and clean
thoroughly to remove
all residues left on the
bottom. This can be done
using the spatula on the
brush (C5) provided.
45
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coees, the grounds container may ll
up more than expected and clog the machine.
18.4 Cleaning the drip tray
Important!
The drip tray (A14) is tted with a level indicator (A12) (red)
showing the level of water it contains (g. 46). Before the indicator protrudes from the cup tray (A11), the drip tray must be
emptied and cleaned, otherwise the water may overow the
edge and damage the appliance, the surface it rests on or the
surrounding area.
To remove the drip tray, proceed as follows:
3. Remove the drip tray and the coee grounds container
(A10) (g. 45);
4. Empty the drip tray and
grounds container and
wash them;
5. Remove the drip tray complete with grounds
container.
18.5 Cleaning the inside of the coee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned o
(see section “7. Turning the appliance o”) and unplugged from
the mains power supply. Never immerse the coee machine in
water.
1. Check regularly (about
once a month) that the
inside of the appliance
(accessible after removing
the drip tray, A14) is not
dirty.
2. If necessary, remove
coee deposits with the
brush (C5) supplied and a
sponge.
3. Remove all the residues
with a vacuum cleaner
(g. 47).
18.6 Cleaning the water tank
1. Clean the water tank (A16) regularly (about once a month)
and whenever you replace the water softener lter (C4) (if
provided) with a damp cloth and a little mild washing up
liquid. Rinse thoroughly before lling the tank and putting it
back in the appliance;
2. Remove the lter (if present) and rinse with running water;
3. Replace the lter (if provided), ll the tank with fresh water
and replace the tank;
4. (Models with water softener lter only) Deliver about
100ml of hot water to reactivate the lter.
22
Page 18
18.7 Cleaning the coee spouts
49 50
PUSH
PUSH
51 52
48B
48A
53
PUSH
1. Clean the coee spouts (A8)
regularly with a sponge or
cloth (g. 48A);
2. Check that the holes in
the coee spouts are not
blocked. If necessary, remove coee deposits with
a toothpick (g. 48B).
18.8 Cleaning the pre-
ground coee funnel
Check regularly (about once a
month) that the pre-ground
coee funnel (A4) is not
blocked. If necessary, remove coee deposits with the brush (C5)
supplied.
18.9 Cleaning the infuser
The infuser (A19) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see “7. Turn-
ing the appliance o”);
2. Remove the water tank (A16) (g. 3);
3. Open the infuser door (A18) (g. 49) on the right side of
the appliance;
6. Use the brush (C5) to remove any coee residues left in the
infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto the internal support (g. 51), then push the PUSH symbol fully in
until it clicks into place;
Please note!
If the infuser is dicult to insert, before insertion, adapt it to the
right size by pressing the two levers shown in g. 52.
8. Once inserted, make sure
the two coloured buttons
have snapped out (g. 53);
9. Close the infuser door;
10. Put the water tank back.
18.10 Cleaning
the milk container
To keep the frother ecient,
clean the milk container (D)
every two days as described
below:
1. Remove the lid (D2);
2. Remove the milk spout (D5) and intake tube (D4) (g. 54);
3. Turn the froth adjustment dial (D1) anticlockwise to the
"INSERT" position (g. 54) and pull it o upwards;
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (g. 50);
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap;
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID NO DISH WASHER
Clean the infuser without using washing up liquid as it could be
damaged.
54
23
Page 19
4. Wash all the components thoroughly with hot water and
mild washing-up liquid. All components are dishwash-
er safe, placing them in the top basket of the dishwasherMake sure there are no milk residues on the hollow
and groove under the dial (g. 55). If necessary, scrape the
groove with a toothpick;
5. Rinse inside the froth adjustment dial seat with running
water (g. 56);
6. Check that the intake tube and spout are not clogged with
milk residues;
7. Replace the dial (in correspondence to the word "INSERT"),
spout and milk intake tube;
8. Place the lid back on the milk container (D3).
55 56
19. DESCALE
Important!
• Before use, read the instructions and the labelling on the
descaler pack.
• You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer's guarantee.
Descale the appliance when "DESCALING NEEDED PRESS OK TO
START (~45min) " appears on the display (B): to descale
immediately, press " " and follow the instructions from
point 4.
To descale the appliance later, press " ". The symbol appears on the display to remind you that the appliance
needs descaling (the message appears each time you turn the
appliance on).
To access the descaling menu:
1. Press " " (B2) to enter the menu;
2. Press (B10) or
on the display;
3. Press " " to start the descaling cycle then follow the
instructions on the display;
4. "REMOVE WATER SOFTENER FILTER" (g. 57): extract the
water tank (A16), remove the water softener lter (C4) (if
present) and empty the water tank. Press " ";
(B8)
until " DESCALE" appears
18.11 Cleaning the hot water/steam connection
nozzle
Each time you prepare milk, clean the connection nozzle (A9)
with a sponge to remove milk residues from the gaskets (g.
23).
18.12 Cleaning the "Mix Carafe" (E)
After each use, clean the carafe as described below:
1. Lift the lid (E1) and remove the funnel (E2) by pressing the
release button (E6) and lifting (g. 28);
2. Extract the steam spout (E3) and "choco" (E4) or "aero"
(E7) stirrer;
3. Wash all the components thoroughly with hot water and
mild washing-up liquid. All components are dish-
washer safe, placing them in the top basket of the
dishwasher.
4. Replace all the components in the appliance.
Please note!
After making hot chocolate, it is normal to nd residues on the
stirrer while cleaning. These consist of traces of iron in the cocoa
attracted by the magnets in the stirrer.
A B
+
B
A
57
5. "ADD DE'LONGHI DESCALER (LEVEL A) AND WATER (UP TO
LEVEL B)" (g. 58); Pour the descaler into the tank up to the
level A marked inside the tank (equal to one 100 ml pack),
then add water (one litre) up to level B and put the water
tank back. Press " ";
6. "EMPTY GROUNDS CON
TAINER AND DRIP TRAY"
(g. 59): remove, empty
and replace the drip
tray (A14) and grounds
container (A10). Press "
";
59
24
58
Page 20
7. "PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
DESCALING": Place an empty container with a minimum
capacity of 2 litres under the hot water/steam spout (C6)
and coee spouts (A8) (g. 8);
Important! Danger of burns
Hot water containing acid ows out of the hot water/steam
spout. Take care to avoid contact with splashes of this solution.
8. Press " " to conrm that you have added the descaling solution. "DESCALING UNDERWAY, PLEASE WAIT"
appears on the display. The descale programme starts and
the descaler liquid comes out of the hot water/steam and
coee spouts. A series of rinses and pauses is performed
automatically to remove all the scale residues inside the
coee machine;
After about 25 minutes, descaling stops:
9. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (g. 5):
the appliance is now ready to rinse with fresh water. Empty
the container used to collect the descaler solution. Extract
the water tank, empty, rinse under running water, ll
with fresh water up to the MAX level and put back in the
appliance;
10. "PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
RINSING": Place the container used to collect the descaler
solution empty under the coee spouts and hot water/
steam spout (g. 8) and press " ";
11. Hot water is delivered rst from the coee spouts, then
from the hot water/steam spout and "RINSING UNDERWAY,
please wait" is displayed;
12. When the water in the tank has run out, empty the container used to collect the rinsing water;
13. (If the lter is installed) "INSERT FILTER INTO ITS HOUSING"
(g. 60). Press " " and extract the water tank.
Replace the water softener lter if removed previously;
14. "RINSE AND FILL WITH
WATER UP TO MAX LEVEL"
(g. 5): Fill the tank up to
the MAX level with fresh
water;
15. "INSERT WATER TANK"
(g. 6): Put the water tank
back in the appliance;
16. "PLACE 2l CONTAINER
UNDER SPOUTS PRESS OK
TO START RINSING": Place
60
the container used to
collect the descaler solution empty under the hot
water/steam spout (g. 8)
and press " ";
17. Hot water is delivered from the hot water/steam spout and
"RINSING UNDERWAY" is displayed.
18. "EMPTY DRIP TRAY" (g. 45): At the end of rinsing, remove,
empty and replace the drip tray (A14) and grounds container (A10). Press " ";
19. "DESCALE COMPLETE": press “ ”;
20. "FILL TANK WITH FRESH WATER": empty the container used
to collect the rinse water, remove the water tank and ll
with fresh water up to the MAX level, then put back in the
appliance.
Descaling is complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A10) to contain water.
• If the water tank has not been lled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been completely eliminated from the machine's internal circuits. Before
starting rinsing, remember to empty the drip tray;
• The appliance may request descaling cycles at very short
intervals. This is normal and due to the appliance’s advanced control system
20. SETTING WATER HARDNESS
The "DESCALING NEEDED - PRESS OK TO START (~45min)
" message is displayed after a period of time established according to water hardness.
The machine is set by default for a hardness level of 4. The machine can also be programmed according to the hardness of the
mains water in the various regions so that the machine needs to
be descaled less often.
20.1 Measuring water hardness
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
25
Page 21
soft water
61
slightly hard water
hard water
very hard water
20.2 Setting water hardness
1. Press " " (B2) to enter the menu;
2. Press (B10) or (
appears on the display (B);
3. To change the level selected, press the symbol itself until
the required level is displayed (Level 1 = soft water; Level
4 = very hard water);
4. Press " " to go back to the homepage.
The machine is now reprogrammed with the new water hardness setting.
B8)
until " WATER HARDNESS"
21. WATER SOFTENER FILTER
Certain models are tted with a water softener lter (C4). If this
is not the case with your model, you are recommended to purchase one from De’Longhi Customer Services.
To use the lter correctly, follow the instructions below.
6. "RUN WATER INTO FILTER
HOLE UNTIL IT COMES OUT
FROM OPENINGS" (g.
62): To activate the lter,
run tap water through the
hole in the lter as shown
in the gure until water
comes out of the openings at the side for more
than a minute. Press "
";
62
7. Extract the tank (A16) from the appliance and ll with
water.
8. "IMMERSE FILTER IN THE
WATER TANK LETTING
AIR BUBBLES ESCAPE"
(g. 63): Insert the lter
in the water tank and
immerse it completely
for about ten seconds,
sloping it and pressing it
lightly to enable the air
bubbles to escape. Press
" ";
63
21.1 Installing the lter
1. Remove the lter (C4)
from the packaging;
2. Press " " (B2) to enter
the menu;
3. Press (B10) or
(B8)
until " WATER
FILTER" appears on the
display;
4. Press " ";
5. "TURN DATE INDICATOR TO
DISPLAY NEXT 2 MONTHS"
(g. 61):
turn the date indicator
disk until the next two months of use are displayed. Press "
";
Please note
The lter lasts about two months if the appliance is used normally. If the coee machine is left unused with the lter installed, it will last a maximum of 3 weeks.
9. "INSERT FILTER INTO ITS HOUSING AND PUSH IT DOWN TO
BOTTOM": Insert the lter in the lter housing (A17) (g.
60) and press as far as it will go. Press " ";
10. "INSERT WATER TANK": Close the tank with the lid (A15),
then replace the tank in the machine.
11. "PLACE 0.5L CONTAINER UNDER SPOUTS, PRESS OK TO
FILL FILTER" (g. 8): Place the container under the hot
water/steam spout (C6) and press
begins and stops automatically.
The symbol appears on the display alongside the time to
indicate that the lter has been enabled. You can now use the
coee machine.
" ". Delivery
21.2 Replacing the lter
Replace the lter (C4) when " REPLACE WATER SOFTENER
FILTER, PRESS OK TO START" appears on the display (B1): to replace immediately, press " " and follow the instructions
from point 4.
To replace the lter later, press " ". The symbol
appears on the display to remind you that the lter needs
replacing.
26
Page 22
To replace, proceed as follows:
1. Extract the tank (A16) and exhausted lter;
2. Remove the new lter from the packaging;
3. Press " " (B2) to enter the menu;
4. Press (B10) or
(B8)
until " WATER FILTER" ap-
pears on the display;
5. Press " ";
6. " REPLACE FILTER" appears on the display;
7. Press " ";
8. Follow the operations described in the previous section
from point 5.
The lter is now active and you can use the coee machine.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the lter even if
the message has not yet been displayed.
21.3 Removing the lter
If you want to use the appliance without the lter (C4), you
must remove it and notify the appliance of its removal. Proceed
as follows:
1. Extract the tank (A16) and exhausted lter;
2. Press " " (B2) to enter the menu;
3. Press (B10) or (
pears on the display;
4. Press " ";
5. " REMOVE FILTER" appears on the display;
6. Press " ";
7. " CONFIRM REMOVE FILTER": press " " (or
press " " to go back to the settings menu);
8. " FILTER REMOVED": the change has been saved.
Press " " to go back to the homepage.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should remove/replace the lter
even if the message has not yet been displayed.
B8)
until " WATER FILTER" ap-
This product complies with European regulation no.
1935/2004 on materials and articles intended to come
into contact with food.
23. DISPOSING OF THE APPLIANCE
The appliance must not be disposed of with household
waste, but taken to an authorised waste separation
and recycling centre.
22. TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10 A
Power: 1450 W
Pressure: 1.9 MPa (19 bars)
Water tank capacity: 2 l
Size LxDxH: 260x480x375 mm
Cord length: 1750 mm
Weight: 12.4 kg
Beans container capacity: 400 g
27
Page 23
24. DISPLAYED MESSAGES
DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY
FILL TANK WITH FRESH
WATER
INSERT WATER TANK The tank
EMPTY GROUNDS CONTAINER The grounds container (A10) is full.
INSERT GROUNDS CONTAINER After cleaning, the grounds container
Insucient water in the tank
(A16)
is not correctly in place. Insert the tank correctly and press as far as it will go.
(A10)
has not been replaced.
(A16)
. Fill the tank with water and/or insert it correctly,
pushing it as far as it will go until it clicks into place.
Empty the grounds container and drip tray (A14),
clean and replace. Important: when removing the drip
tray, the grounds container must be emptied, even if
it contains few grounds. If this is not done, when you
make the next coees, the grounds container may ll
up more than expected and clog the machine.
Remove the drip tray (A14) and insert the grounds
container.
ADD PREGROUND
COFFEE MAX. 1 MEASURE
The "pre-ground coee" function has
been selected without placing any preground coee in the funnel
(A4)
.
28
Place pre-ground coee in the funnel
repeat delivery
(g. 14)
and
Page 24
DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY
ADD COFFEE
COFFEE MAX. 1 MEASURE
A LONG coee with pre-ground coee has
been requested
Place pre-ground coee in the funnel (A4) (g. 14)
and press " " to continue and complete
delivery.
FILL BEANS CONTAINER The coee beans have run out. Fill the beans container
GROUND TOO FINE. ADJUST
MILL 1 CLICK WHILE IN
OPERATION
SELECT A MILDER TASTE
OR REDUCE PREGROUND
COFFEE QUANTITY
The pre-ground coee funnel
clogged.
The grinding is too ne and the coee is
delivered too slowly or not at all.
If the water softener lter (C4) is present,
an air bubble may have been released inside the circuit, obstructing delivery.
Too much coee has been used.
(A4)
is
Empty the funnel with the help of the brush (C5) as
described in section “18.8 Cleaning the pre-ground
coee funnel”.
Repeat coee delivery and turn the grinding adjustment dial
(A5) (g. 11)
while the coee mill is in operation. If after making
at least 2 coees delivery is still too slow, repeat the
correction procedure, turning the grinding adjustment dial another click until delivery is correct (see
section “9.5 Adjusting the coee mill”). If the problem persists, make sure the water tank (A16) is fully
inserted.
Insert the hot water/steam spout (C6) in the appliance and deliver a little water until the ow becomes
regular.
Select a milder taste by pressing " AROMA" (B6)
or reduce the quantity of pre-ground coee (maximum 1 measure).
(A3 - g. 12)
one click clockwise towards 7
.
29
Page 25
DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY
INSERT WATER SPOUT The hot water spout (C6) is not inserted
Insert the water spout as far as it will go.
or is inserted incorrectly
INSERT MILK CONTAINER The milk container (D) is not inserted
Insert the milk container as far as it will go
correctly.
INSERT INFUSER ASSEMBLY
PUSH
The infuser (
after cleaning.
A19
) has not been replaced
Insert the infuser as described in section “18.9 Cleaning the infuser”.
INSERT "MIX CARAFE" The carafe (E) is not correctly in place Insert the carafe and push as far as it will go
WATER CIRCUIT EMPTY
PRESS OK TO START FILLING
PROCESS
The water circuit is empty
Press " " to deliver water from the spout
(
C6)
until it ows out normally. Delivery stops
automatically.
If the problem persists, make sure the water tank
(A16) is fully inserted.
(g. 19)
.
30
Page 26
DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY
PRESS OK TO START CLEANING
PROCESS OR TURN MILK
FROTH ADJUSTMENT DIAL
The milk container has been inserted
with the froth adjustment dial (D1) in the
"CLEAN" position.
To proceed with the CLEAN function, press
" or turn the froth adjustment dial to one of the milk
positions.
"
TURN DIAL TO <CLEAN> POSITION TO START CLEANING
CLEAN
TURN THE MILK FROTH
ADJUSTMENT DIAL TO MILK
POSITION
DESCALING NEEDED
PRESS OK TO START
~45MIN
REPLACE WATER SOFTENER
FILTER
PRESS OK TO START
Milk has been delivered recently and the
tubes inside the milk container must be
cleaned (D).
The milk container has been inserted
with the froth adjustment dial (D1) in the
"CLEAN" position.
The machine must be descaled.
The water softener lter (C4) is
exhausted.
Turn the froth adjustment dial (D1) to CLEAN
(g.
21).
Turn the dial to the required froth position.
Press " " to start descaling or "" " to
descale later. The descaling procedure described in
section “19. Descale” needs to be performed.
Press " " to replace or remove the lter, or "
" to carry out the procedure later. Follow the
instructions in section “21. Water softener lter”.
31
Page 27
DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY
END PREPARATION? While making a cold beverage,
CONTINUE MIXING? When preparation of a cold beverage is
YES
“ ” has been pressed
The carafe has been removed while a cold
NO
beverage is being prepared
YES
complete, you can continue mixing twice
up to a maximum of about a minute.
To conrm that preparation is complete, press "YES"
or press "NO" to continue mixing.
If the froth is satisfactory, press "NO", otherwise
press "YES" to continue mixing.
GENERAL ALARM: USER
MANUAL / SMART COFFEE
APP
NO
The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly, as
described in section “18. Cleaning”. If the message
is still displayed after cleaning, contact customer
services.
The appliance needs descaling and/or the
lter (C4) must be replaced.
The tubes inside the milk container (D)
must be cleaned.
The lter (C4) must be replaced. Replace the lter or remove it as described in section
The machine must be descaled. The descaling procedure described in section “19.
The auto-start function is enabled. To disable the function, proceed as described in sec-
Energy saving is enabled. To disable energy saving, proceed as described in
The appliance is connected to a device via
bluetooth.
The descaling procedure described in section “19.
Descale” needs to be performed and/or the lter
needs replacing or removing as described in section
“21. Water softener lter”.
Turn the froth adjustment dial (D1) to CLEAN
21).
“21. Water softener lter”.
Descale” needs to be per formed.
tion “8.6 Auto-star t ”.
section “8.9 Energy saving ”.
(g.
Indicates that the lter (C4) has been
enabled
CLEANING UNDERWAY
PLEASE WAIT
APPLIANCE TOO HOT Using the stirrers continuously for long
The appliance has detected impurities in
its internal circuits.
periods may cause the appliance to
overheat
32
To remove the lter, proceed as described in section
“21. Water softener lter”.
Wait for the appliance to be ready for use again and
reselect the required beverage. Contact Customer
Services if the problem persists.
Wait for the appliance to cool down.
Page 28
25. TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM POSSIBLE CAUSE REMEDY
The coee is not hot. The cups were not preheated. Warm the cups by rinsing them with hot
water (Please note: you can use the hot water
function).
The infuser has cooled down because
2/3 minutes have elapsed since the last
coee was made.
A low coee temperature is set.
The coee is weak or not creamy
enough.
The coee is delivered too slowly or a
drop at a time.
Coee does not come out of one or
both of the spouts.
Coee is not delivered The appliance has detected impurities
The appliance does not come on The power cord (C8) connector is not
The coee is ground too coarsely. Turn the grinding adjustment dial (A5) one
The coee is unsuitable. Use pre-ground coee for espresso machines.
The coee is ground too nely. Turn the grinding adjustment dial (A5) one
The coee spouts (A8) are blocked. Clean the spouts with a toothpick (g. 48B).
in its internal circuits. "Cleaning underway" is displayed.
inserted correctly.
It is not plugged into the mains socket. Plug into the mains socket (g. 1).
Before making the coee, heat the infuser by
rinsing using the rinse function
“8.1 Rinsing ”).
Set a hotter coee temperature in the menu
(section “8.10 Coee temperature ” ) .
click anticlockwise towards 1 while the coee
mill is in operation (g. 11). Continue one click
at a time until coee delivery is satisfactory.
The eect is only visible after delivering 2
coees (see section “9.5 Adjusting the coee
mill”).
click anticlockwise towards 7 while the coee
mill is in operation (g. 11). Continue one click
at a time until coee delivery is satisfactory.
The eect is only visible after delivering 2
coees (see section “9.5 Adjusting the coee
mill”).
Wait for the appliance to be ready for use again
and reselect the required beverage. Contact
Customer Services if the problem persists.
Insert the connector as far as it will go in the
socket at the back of the appliance
(see section
(g. 1)
.
The main switch (A21) is not turned on. Press the main switch (g. 2).
The infuser cannot be extracted The appliance has not been turned o
correctly
At the end of descaling, the appliance
requests a third rinse
The milk does not come out of the
milk spout (D5)
During the two rinse cycles, the water
tank (A16) has not been lled to the
MAX level
The lid (D2) of the milk container (D)
is dirty
33
Turn the appliance o by pressing the button (A7)
(section “7. Turning the appliance o”).
Follow the instructions displayed by the appliance, but rst empty the drip tray (A14) to avoid
the water overowing.
Clean the milk container lid as described in the
section “18.10 Cleaning the milk container”.
Page 29
PROBLEM POSSIBLE CAUSE REMEDY
The milk contains large bubbles and
squirts out of the milk spout (D5) or
there is little froth
The milk is not cold enough or is not
semi-skimmed or skimmed.
Use skimmed or semi-skimmed milk at refrigerator temperature (about 5° C). If the result is
not as you wished, try changing brand of milk.
The froth adjustment dial (D1) is incorrectly adjusted.
The milk container lid (D2) or froth adjustment dial (D1) is dirty
The hot water/steam connection nozzle (A9) is dirty
The cup warmer is hot, even though it
has been disabled
The chocolate is not suciently dense The hot chocolate powder does not
The hot chocolate is cold or there are
lumps
During cleaning, there are traces of
black on the stirrer (E4)
There is little or no froth on the cold
coee
A number of beverages have been prepared in rapid succession
contain thickener.
The highest density has not been
selected.
Incorrect quantities of milk and hot
chocolate powder.
The wrong stirrer has been inserted Remove the aero stirrer (E7) and insert the
The stirrer (E4) and steam spout (E3)
are not inserted correctly in the funnel
(E2).
The instructions have not been
followed.
The magnets in the stirrer attract traces of iron naturally present in the hot
chocolate powder.
"MIN" froth has been selected Select “EXTRA” froth (see section “15.1 Making
The stirrer is missing or inserted
incorrectly
Too much, or the wrong quantity of ice
has been used
The coee is unsuitable or has been left
open for too long
Adjust following the instructions in section
“10.2 Adjusting the amount of froth”.
Clean the milk container lid and froth adjustment dial as described in section “18.10 Cleaning the milk container”.
Clean the connection nozzle as described in
section “18.11 Cleaning the hot water/steam
connection nozzle”.
Change the type of hot chocolate powder.
Select maximum density in the corresponding screen. (See section “14. making hot
chocolate”)
Respect the instructions in section “14. making
hot chocolate”.
choco stirrer (E4)
Insert the stirrer and steam spout on the
funnel.
Pour the milk/water into the funnel (E2) rst,
followed by the hot chocolate powder.
Clean as described in section “18.12 Cleaning
the “Mix Carafe” (E)”.
cold coee”)
Insert the aero stirrer (E7)
Respect the instructions in section “15. making
cold beverages”.
Use "fresh", ideally "robusta" coee
34
Page 30
PROBLEM POSSIBLE CAUSE REMEDY
The cold coee is hot Too little and/or the wrong quantity of
ice has been used
The ice is not completely dissolved Continue stirring, press "YES" at the end of
There is little or no froth on the cold
milk
The "SMALL" quantity is selected, but
the quantity of milk for a large cup has
been used
"MIN" froth has been selected Select “EXTRA” froth (see section “15.1 Making
The stirrer is missing, or the wrong one
has been used
The milk is unsuitable Change brand of milk
Respect the instructions in section “15. making
cold beverages”.
preparation when the prompt appears on the
display
Respect the instructions in section “15. making
cold beverages”.
cold coee”)
Insert the aero stirrer (E7)
The cold milk is hot Hot milk, or milk at room temperature
has been used
The machine emits noises or small
pus of steam while not in use
The machine is ready for use, or has recently been turned o, and condensate
is dripping into the hot vaporiser
Use milk at refrigerator temperature (5° C)
This is part of normal operation. To limit the
phenomenon, empty the drip tray.
35
Page 31
26. ELECTRICAL REQUIREMENTS
Before using this appliance ensure that the voltage indicated on the produc t corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The exible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not t the socket outlets in your home, it should be cut o and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might nd it and plug it into a supply socket - with the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be switched o when the machine is not in
use.
IMPORTANT: The wires in the mains lead tted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWN LIVE
Blue to
neutral
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualied
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualied electrician and should
only be replaced with a exible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be retted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be tted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
13 amp Fuse
Brown to live
Cord Clamp
36
Loading...