instructions
DRAGON HM3
Please retain these instructions for future reference
GB 3-06-2004 11:27 Pagina 1
Fig.1
Dragon HM3
2
Thank you for choosing this De’Longhi radiator. To get the
very best out of your new radiator it is advisable to read
these instructions before using it.This will ensure that you
gain optimum results and use the appliance safely.
General instructions
Take the radiator out of its packing box and remove any polystyrene pieces or any other packaging material that might be lodged
inside it.
Make sure that the radiator has not been damaged during transit and
that the mains cable is in working order.Do not operate the radiator if damaged.
“Easy wheel”system
Turn the radiator upside-down on a rug or a soft surface in order to
prevent damaging the paint finish.Fully unfold the castors by turning
them outwards (Fig.1).
Turn the radiator back to its upright position.
Electrical connection
- Before plugging the radiator into the mains,check that your
supply voltage is the same as that shown on the rating plate of
the radiator.
- If using more than one appliance at a time,it is important to
ensure that the ring main is adequate to cope with the power
requirements.
- It is important to ensure that the socket is adequately earthed.
- This radiator complies with EEC Directive 89/336 relating to
electromagnetic compatibility.
How to use it
Switching on
Plug the radiator in; position the thermostat slider to maximum and
turn the radiator on as follows using the power selector:
•Turn the power selector to position 1 to select minimum output
(the light on the left will come on).
•Turn the power selector to position 2 to select medium output
(the light on the right will come on).
•Turn the power selector to position 3 to select maximum output
(both lights will come on).
Adjusting the thermostat
Leave the thermostat at its highest setting until the room has
reached the required temperature.Then slowly turn the thermostat slider back until you hear a click.The temperature selected in
this way will then be regulated automatically and kept constant by
the thermostat.
GB 3-06-2004 11:27 Pagina 2
3
Frost protection function
With the thermostat slider in the minimum position and a power
selected,the unit maintains the room at a temperature of about
5˚C, preventing freezing with minimum energy consumption.
Models with 24-hour timer
Using the timer
If you wish to use the timer ,position the switch in the middle position .
(Fig.4).
Setting the correct time
Check the time on your watch.If for example it is 4.00 pm.(16.00),
turn the dial in a clockwise direction until the number 16 is lined up
with the triangular pointer (fig.2).
N.B.:Never turn the dial in an anti-clockwise direction!
The timer is in effect an electric clock and works only if the plug is
connected to the power supply. Whenever the plug is disconnected
or there is a power failure,the clock must be re-set.
To program the timer
1) Set the operating times by pushing out with your thumbnail to
the outer rim,the notches on the dial corresponding to the period
required (fig.3) (each notch represents 15 mins.)
2) Make sure that the timer indicates the correct time (see instruc-
tions on setting the correct time).
3) Turn the radiatior on and set it to the heat setting and tempera-
ture level on the thermostat as required.
Once programmed in this way, the appliance will repeat the preestablished program every day,if the selector is in the position.
Timer override
If you wish to override the timer settings,push the timer switch to
position 1 (fig.4) manual (timer override).To return to timed operation push the switch back to the middle position (fig.4).
NOTE: if the timer switch is at the 0 position (fig.4),the heater is
off and will not operate).
I Manual (timer override)
0
Timer operation
Heater off
Fig.2
21
20
19
16
pointer
21
20
19
16
operating time
fig.3
fig.4
Dragon HM3
GB 3-06-2004 11:27 Pagina 3
4
Cleaning and maintenance
Your oil filled raditor is absolutely free from maintenance,fully reliable and will give many years of trouble free service.Wipe radiator
with soft damp cloth;do not use detergents or abrasives.
If necessary,use a vacuum cleaner to remove any built-up dirt.
Important notes
- Do not use your radiator close to bath, wash-basin, shower and
swimming pool.
- Do not use your radiator to dry laundry.
-Never place the power cable on top of the radiator while it is hot.
- Only use the radiator in an upright position.
- The heater must be positioned at least 50 cm from furniture or
other objects.
- If the power cable has been damaged, it must be replaced by the
manufacturer or the technical service centre or by a qualified per-
son so as to avoid all risks.
- In order to eliminate the radiator’s “new” smell, set it to maximum
power for at least 8 hours when used for the first time.During this
operation,the room in which the radiator is located must be venti-
lated.
- It is perfectly normal for the radiator to make “creacking” sounds when
used for the first time.(or in the case of unfrequent use).
- The radiator must not be located immediately below a fixed sock et-outlet.
- The body of this radiator is filled with a precise quantity of special
oil, so that repairs requiring the opening of the oil body must only
be made by the service agent. Any oil leakage must be reported to
the service agent.
- Do not use this appliance in rooms having a floor area of less than
4m
2
as this can lead to overheating.
- If the appliance is scrapped, provisions on the disposal of oil must
be respected.
- The use of an extension lead is not recommended,as overheating of
the extension lead may occur during the operation of the radiator.
- As with any electrical appliance,whilst the instructions aim to cover
as many eventualities as possible,caution and common sense should
be applied when operating your appliance,particularly in the vicinity
of young children.
The appliance is fitted with a safety device which will switch off it in
case of accidental overheating. To reset, disconnect the plug from the
power for 30 minutes, remove the cause of overheating then plug the
appliance in again.
ATTENTION: in order to avoid any danger caused by an acciden
tal
resetting of the safety system, this appliance must not be powered
through an external timer.
IMPORTANT: Do not cover the radiator during operation as this could lead to dangerous overheating,
Dragon HM3
GB 3-06-2004 11:27 Pagina 4
Electrical requirements
Before using this appliance ensure that the voltage indicated
on the product corresponds with the main voltage in your
home, if you are in any doubt about your supply contact your
local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug
having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home,it should be cut off and replaced with a suitable plug,
following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should
therefore be properl y disposed of and not left wher e children might find
it and plug it into a supply socket - with the obvious consequent danger.
N.B.We recommend the use of good quality plugs and wall sockets that
can be switched off when the machine is not in use.
important: the wires in the mains lead fitted to this appliance are
coloured in accordance with the following code:
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug,proceed as follows:
The wire which is coloured green and yellow must be connected to the
terminal in the plug which is marked with the letter E or by the earth
symbol or coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely
retained in each terminal.Do not forget to tighten the mains lead clamp
on the plug.If your electricity supply point has only two pin socket outlets,or if you are in doubt,consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this
operation be carried out by a qualified electrician and should only be
replaced with a flexible cord of the same size.
After replacement of a fuse in the plug,the fuse cover must be refitted.
If the fuse cover is lost, the plug must not be used until a replacement
cover is obtained. The colour of the correct replacement fuse cover is
that of the coloured insert in the base of the fuse recess or elsewhere
on the plug. Always state this colour when ordering a replacement fuse
cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362
should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
GREEN AND YELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
Green and Yellow to Earth
Blue to
Neutral
13 amp
Fuse
Brown
to Live
Cord Clamp
Warning - this appliance
must be earthed
Dragon HM3
5
GB 3-06-2004 11:27 Pagina 5
5710008300/05.04
GB 3-06-2004 11:27 Pagina 6
Loading...