Dell PowerEdge SC 440 User Manual [en, es, fr]

Dell™ PowerEdge™

SC440 Systems

Getting Started With

Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Model DCTA

www.dell.com | support.dell.com

Dell™ PowerEdge™

SC440 Systems

Getting Started With

Your System

www.dell.com | support.dell.com

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell, the Dell logo, and PowerEdge are trademarks of Dell Inc.; Intel, Pentium, and Celeron are are registered

trademarks of Intel Corporation; Microsoft and Windows are registered trademarks and Windows Server is a trademark of Microsoft Corporation; Red Hat is a registered trademark of Red Hat, Inc.; SUSE is a registered trademark of Novell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model DCTA

May 2006 P/N KH738 Rev. A00

System Features

The major hardware and software features of your system include:

• One of the following processors:

–Intel

– Intel Pentium 4, 600 sequence.

All processors are Intel Extended Memory 64 Technology (Intel EM64T) capable.

• A minimum of 512 MB of 533- or 667- (when available) MHz DDR II SDRAM memory, upgradable to a maximum of 4 GB DDR II SDRAM memory by installing 512-MB or 1-GB unbuffered ECC memory modules in the four memory module sockets on the system board; single or dual rank.

• Support for the following internal hard-drive (non–hot-plug) configurations:

– Up to two internal 3.5-inch SATA hard drives with an integrated SATA controller

– Up to two internal 3.5-inch Serial-Attached SCSI (SAS) hard drives with a SAS controller card

• One 3.5-inch peripheral drive bay for the optional diskette drive, and two 5.25-inch bays for the following supported drives: CD, DVD, combination CD-RW/DVD, or tape backup device.

• Support for the following disk volume types: simple, spanned, stripped (RAID 0), and mirrored (RAID 1).

• Support for USB 2.0.

• A chassis intrusion alert.

The system board includes the following integrated features:

• Dual-channel IDE controller that supports up to two supported devices including IDE CD, DVD, CDRW/DVD combination drive, and an IDE tape backup device.

Pentium® D processor, E6000 sequence.

Celeron® D, 300 sequence.

NOTE: Use the System Setup program to view processor information. See the Hardware Owner’s Manual.

NOTE: DVD devices are data only.

• SATA controller that supports up to two cabled SATA hard drives.

• Two 32-bit, 33-MHz I/O expansion card slots, one x1 lane-width PCIe expansion slot, one x4 lanewidth PCIe expansion slot, and one x8 lane-width PCIe expansion slot.

• An integrated VGA-compatible video subsystem with an ATI ES1000, 33-MHz PCI video controller. This video subsystem contains 16 MB of graphics memory with support for 2D graphics. Maximum resolution is 1600x1200 with 65,536 colors; true-color graphics are supported in the following resolutions: 640 x 480, 800 x 600, 1024 x 768, and 1280 x 1024.

NOTE: Your system supports integrated video only.

Getting Started With Your System 3

• An integrated Gigabit Ethernet NIC, capable of supporting 1000-Mbps, 100-Mbps, or 10-Mbps data rates, with support for PXE and Wake-on-LAN.

• Seven USB 2.0-compliant connectors (two on the front and five on the back) capable of supporting a diskette drive, a CD-ROM drive, a keyboard, a mouse, or a USB flash drive.

• Back-panel connectors include serial, video, five USB connectors, and one NIC connector.

• Front-panel connectors include two USB connectors.

• Four front-panel system diagnostic LEDs for failure messaging and notification during startup.

For more information about specific features, see "Technical Specifications" on page 8.

Supported Operating Systems

Your system supports the following operating systems:

• Microsoft® Windows Server™ 2003, Standard Edition

• Microsoft Windows Server 2003, Standard x64 Edition

• Microsoft Windows

•Red Hat

• Red Hat Enterprise Linux (version 4) for Intel x86

•SUSE

Enterprise Linux (version 4) for Intel EM64T

LINUX Enterprise Server 10

Small Business Server 2003 Standard and Premium Editions

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and regulatory information.

Warranty information may be included within this document or as a separate document.

• The

• CDs included with your system provide documentation and tools for configuring and managing

• Updates are sometimes included with the system to describe changes to the system, software, and/or

Hardware Owner’s Manual

troubleshoot the system and install or replace system components. This document can be found on the CDs that came with your system or on support.dell.com.

your system.

documentation.

provides information about system features and describes how to

NOTE: Always check for updates on support.dell.com and read the updates first because they often

supersede information in other documents.

• Release notes or readme files may be included to provide last-minute updates to the system or documentation or advanced technical reference material intended for experienced users or technicians.

• Operating system documentation describes how to install (if necessary), configure, and use the operating system software.

• Documentation for any components you purchased separately provides information to configure and install these options.

4 Getting Started With Your System

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not perform as expected, see your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see www.dell.com/training for more information. This service may not be offered in all locations.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety instructions and important

regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time.

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

Getting Started With Your System 5

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to plug into each connector.

Be sure to tighten the screws (if any) on the monitor's cable connector.

Connecting the Power

Connect the monitor power cable to the monitor (optional), and connect the system’s power cable to the system.

Plug the other end of the power cables into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

6 Getting Started With Your System

Turning on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power indicators should light. Adjust the monitor's controls until the displayed image is satisfactory.

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the Quick Installation Guide. Be sure the operating system is installed before installing hardware or software not purchased with the system.

Getting Started With Your System 7

Technical Specifications

Processor

Processor type

Expansion Bus

Bus type PCI and PCIe

Expansion slots

PCIe

PCI Two 5-V, half-length, 32-bit, 33-MHz (slots 3 and 5)

Memory

Architecture

Memory module sockets four 240-pin

Memory module capacities

Minimum RAM

Maximum RAM 4 GB (four 1-GB modules)

Intel® Pentium® D processor, E6000 sequence

Intel Celeron® D, 300 sequence

Intel Pentium 4, 600 sequence.

2.5-Gb/sec PCIe x1, 3.3-V, 12-V (slot 1)

2.5-Gb/sec PCIe x8, 3.3-V, 12-V (slot 2)

2.5-Gb/sec PCIe x4, 3.3-V, 12-V (slot 4)

72-bit, ECC, PC-4300, Unbuffered, DDR II SDRAM, DIMMs, rated for

512 MB or 1 GB

512 MB (one 512-MB module)

533- or 667- MHz operation

Drives

Hard Drives

Diskette drive one optional 2.5-inch, 1.44-MB

Optical drives up to two optional IDE CD, DVD, or combination

Up to two non–hot-plug, 3.5-inch, internal SATA hard drives with the integrated SATA controller

Up to two non–hot-plug, 3.5-inch, internal SAS drives with a SAS controller card

CD-RW/DVD drives

NOTE: DVD devices are data only.

external optional USB CD

8 Getting Started With Your System

Drives (continued)

Tape drive one optional internal half-height, 5.25-inch SATA

(for use in 5.25-inch bay only)

Flash drive external optional USB

Connectors

Back

NIC

Serial

USB

Video

Fro nt

USB

Internally accessible

IDE channel 40-pin

SATA channels

Video

Video type Integrated

Video memory 16 MB

one RJ-45 (for integrated 1-Gigabit NIC)

9-pin, DTE, 16550-compatible

five 4-pin, USB 2.0-compliant

15-pin VGA

two 4-pin, USB 2.0-compliant

Four 7-pin

Power

AC power supply (per power supply)

Wattage

Voltage 115–230 VAC, 60/50 Hz, 9.0-4.5 A

Heat dissipation

CMOS Backup Battery CR 2032 3.0-V lithium ion coin cell

Physical

Height 44.8 cm (17.6 in)

Width 17.1 cm (6.8 in)

Depth 46.7 cm (18.4 in)

Weight (maximum configuration) 17.7 kg (39 lb)

305 W

1040 BTU/Hour

Getting Started With Your System 9

Environmental

NOTE: For additional information about environmental measurements for specific system configurations,

see www.dell.com/environmental_datasheets.

Te mp e ra t ur e

Operating

Storage

Relative humidity

Operating

Storage

Maximum vibration

Operating

Storage

Maximum shock

Operating

Storage

Altitude

Operating

Storage

10° to 35°C (50° to 95°F)

–40° to 65°C (–40° to 149°F)

20% to 80% (noncondensing) with a maximum humidity gradation of 10% per hour

5% to 95% (noncondensing)

5 to 350 Hz at 0.0002 G2/Hz

5 to 500 Hz at 0.001 to 0.01 G2/Hz

40 G +/- 5% with pulse duration of 2 msec +/- 10% (equivalent to 20 in/sec [51 cm/sec])

105 G +/- 5% with pulse duration of 2 msec +/- 10% (equivalent to 50 in/sec [127 cm/sec])

–15.2 to 3048 m (–50 to 10,000 ft)

–15.2 to 10,600 m (–50 to 35,000 ft)

10 Getting Started With Your System

Systèmes Dell™ PowerEdge™ SC440

Guide de mise en route

www.dell.com | support.dell.com

Remarques, avis et précautions

REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre

ordinateur.

AVIS : un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter

le problème.

PRÉCAUTION : une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle

ou de mort.

____________________

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc. est strictement interdite. Marques utilisées dans ce document : Dell, le logo Dell et PowerEdge sont des marques de Dell Inc. ; Intel, Pentium et Celeron sont des

marques déposées de Intel Corporation ; Microsoft et Windows sont des marques déposées de Microsoft Corporation ; Windows Server est une marque de Microsoft Corporation ; Red Hat est une marque déposée de Red Hat, Inc. ; SUSE est une marque déposée de Novell Inc.

Tous les autres noms de marques et marques commerciales utilisés dans ce document se rapportent aux sociétés propriétaires des marques et des noms de ces produits. Dell Inc. décline tout intérêt dans l'utilisation des marques déposées et des noms de marques ne lui appartenant pas.

Modèle DCTA

Mai 2006 P/N KH738 Rev. A00

Caractéristiques du système

Les caractéristiques matérielles et logicielles principales du système sont les suivantes :

• L'un des processeurs suivants est installé : –Intel –Intel – Intel Pentium 4, séquence 600. Tous les processeurs sont compatibles Intel EM64T (Extended Memory 64 Technology).

• Mémoire minimale : 512 Mo, sous forme de barrettes de mémoire à simple ou double rangée de connexions, de type SDRAM DDR II à 533 MHz ou 667 MHz (selon disponibilité). Extensible via l'installation de barrettes de mémoire ECC sans tampon de 512 Mo ou 1 Go, dans les quatre supports de modules de mémoire de la carte système. Le maximum autorisé est de 4 Go.

• Prise en charge des configurations suivantes pour le disque dur interne (non connectable à chaud) : – Jusqu'à deux disques durs SATA internes de 3,5 pouces, avec un contrôleur SATA intégré

– Jusqu'à deux disques durs SAS (Serial-Attached SCSI) internes de 3,5 pouces, avec une carte

• Une baie de périphérique 3,5 pouces pouvant accueillir le lecteur de disquette en option, et deux baies 5,25 pouces prenant en charge les lecteurs suivants : lecteur de CD, DVD, CD-RW/DVD ou unité de sauvegarde sur bande.

Pentium® D, séquence E6000.

Celeron® D, séquence 300.

REMARQUE : utilisez le programme de configuration du système pour visualiser les informations concernant

le processeur. Consultez le document Hardware Owner's Manual (Manuel du propriétaire) pour plus de détails.

contrôleur SAS

REMARQUE : les périphériques DVD sont uniquement des périphériques de données.

• Prise en charge des types de volumes de disques suivants : simple, avec concaténation des données (“spanning”), étalement des données (“striping” ou RAID 0) et mise en miroir (RAID 1)

• Support USB 2.0

• Alerte d'intrusion dans le châssis

La carte système contient les éléments suivants :

• Contrôleur IDE à deux canaux prenant en charge jusqu'à deux périphériques (lecteur IDE de CD, DVD, CDRW/DVD, et un lecteur IDE de sauvegarde sur bande)

REMARQUE : les périphériques DVD sont uniquement des périphériques de données.

• Contrôleur SATA prenant en charge jusqu'à deux disques durs SATA reliés par câble.

• Deux emplacements d'E/S pour cartes d'extension (32 bits, 33 MHz) ; un logement d'extension PCIe x1, un logement d'extension PCIe x4 et un logement d'extension PCIe x8

Guide de mise en route 13

+ 33 hidden pages