Page 1
TECHNICAL DATA SHEET
A3 STD SNAP TIE
Light Wall Forming
DESCRIPTION
A3 Standard Snap Tie is manufactured with either hot
or cold forged integral heads and is equipped with flats
or crimps to prevent turning in the concrete during
breakback operations. Coating the tie with wax will aid
in breakback operation.
APPLICATION
Used for handset wood wall forming.
RELATED PRODUCTS
■ A2 Plastic Cone
■ A16 Omni Wedge
■ A81 Jahn® "A" Bracket
■ A82 Jahn® "C" Bracket
ORDERING INFORMATION
METAL SPREADER
Product Code Description Weight
15000 6" X 4-3/4" L&W 0.225 LB
15006 8" X 4-3/4" L&W 0.2435 LB
15012 10" X 4-3/4" L&W 0.2645 LB
15018 12" X 4-3/4" L&W 0.2866 LB
15024 14" X 4-3/4" L&W 0.3081 LB
15030 16" X 4-3/4" L&W 0.344 LB
15036 18" X 4-3/4" L&W 0.365 LB
15044 24" X 4-3/4" L&W 0.4266 LB
15150 6" X 8-1/4" L&W 0.3032 LB
15153 7" X 8-1/4" L&W 0.31 LB
15156 8" X 8-1/4" L&W 0.32 LB
15159 9" X 8-1/4" L&W 0.3325 LB
15162 10" X 8-1/4" L&W 0.3441 LB
15168 12" X 8-1/4" L&W 0.3675 LB
15171 13" X 8-1/4" L&W 0.385 LB
15174 14" X 8-1/4" L&W 0.39 LB
15177 15" X 8-1/4" L&W 0.4 LB
15180 16" X 8-1/4" L&W 0.41 LB
15186 18" X 8-1/4" L&W 0.4372 LB
15190 20" X 8-1/4" L&W 0.4722 LB
15194 24" X 8-1/4" L&W 0.516 LB
15200 30" X 8-1/4" L&W 0.62 LB
15206 36" X 8-1/4" L&W 0.612 LB
FEATURES
■ 2,250 lbs. SWL
■ Available in any length from 6" to 480"
■ Available with plastic cone, metal cone, metal
spreader, flat fixed washer or cupped loose washer
■ Can be manufactured with a tight fitting neoprene
washer located near the center of tie to eliminate
water seepage along the tie
INSTALLATION
1. Drill holes in plywood 1/8" larger than the snap tie
head (usually 5/8" diameter drill bit will be required
2. Place the ends of snap ties through the holes in the
plywood
3. Place the bracket (Jahn® "A", Jahn® "C" or Omni
wedge) on the tie
4. The proper tie head position is at the midpoint or
higher of the Omni wedge slot. Correct spacing
between double wales is 5/8" to 3/4"
5. Jahn® "A" bracket is utilized to hold a single wale and
can be installed before or after the wales have been
positioned
Page 1 of 3 File Date: 8/18/2014
Page 2
TECHNICAL DATA SHEET
A3 STD SNAP TIE
Light Wall Forming
1" X 1" PLASTIC CONES
Product Code Description Weight
15400 6" X 4-3/4" L&W 0.216 LB
15403 7" X 4-3/4" L&W 0.225 LB
15404 7-5/8" X 4-3/4" L&W 0.24 LB
15406 8" X 4-3/4" L&W 0.242 LB
15409 9" X 4-3/4" L&W 0.258 LB
15412 10" X 4-3/4" L&W 0.273 LB
15416 11" X 4-3/4" L&W 0.272 LB
15418 12" X 4-3/4" L&W 0.286 LB
15424 14" X 4-3/4" L&W 0.316 LB
15427 15" X 4-3/4" L&W 0.33 LB
15430 16" X 4-3/4" L&W 0.338 LB
15436 18" X 4-3/4" L&W 0.3584 LB
15440 20" X 4-3/4" L&W 0.375 LB
15444 24" X 4-3/4" L&W 0.437 LB
15448 30" X 4-3/4" L&W 0.52 LB
15056 36" X 4-3/4" L&W 0.526 LB
15450 6" X 8-1/4" L&W 0.304 LB
15453 7" X 8-1/4" L&W 0.31 LB
15454 7-5/8" X 8-1/4" L&W 0.3142 LB
15456 8" X 8-1/4" L&W 0.324 LB
15459 9" X 8-1/4" L&W 0.335 LB
15462 10" X 8-1/4" L&W 0.35 LB
15468 12" X 8-1/4" L&W 0.367 LB
15474 14" X 8-1/4" L&W 0.39 LB
15477 15" X 8-1/4" L&W 0.402 LB
15480 16" X 8-1/4" L&W 0.43 LB
15486 18" X 8-1/4" L&W 0.437 LB
15490 20" X 8-1/4" L&W 0.482 LB
15494 24" X 8-1/4" L&W 0.51 LB
15500 30" X 8-1/4" L&W 0.554 LB
15498 36" X 8-1/4" L&W 0.62 LB
15501 42" X 8-1/4" L&W 0.72 LB
14538 8" X 1-1/16" L&W 0.17 LB
14540 10" X 1-1/16" L&W 0.2 LB
14542 12" X 1-1/16" L&W 0.22 LB
14546 16" X 1-1/16" L&W 0.26 LB
15420 6" X 1-3/16" L&W 0.15 LB
15423 8" X 1-3/16" L&W 0.18 LB
15401 6" X 1-5/8" L&W 0.16 LB
15407 8" X 1-5/8" L&W 0.19 LB
15413 10" X 1-5/8" L&W 0.21 LB
15419 12" X 1-5/8" L&W 0.23 LB
15550 6" X 5-1/8" L&W 0.24 LB
15552 8" X 5-1/8" L&W 0.27 LB
1-1/4" CUPPED LOOSE WASHER
Product Code Description Weight
14232 6" X 4-3/4" L&W 0.24 LB
14236 8" X 4-3/4" L&W 0.26 LB
14239 9" X 4-3/4" L&W 0.27 LB
14242 10" X 4-3/4" L&W 0.28 LB
14245 12" X 4-3/4" L&W 0.3 LB
14246 14" X 4-3/4" L&W 0.33 LB
14252 16" X 4-3/4" L&W 0.35 LB
14255 18" X 4-3/4" L&W 0.37 LB
14261 24" X 4-3/4" L&W 0.44 LB
14248 6" X 8-1/4" L&W 0.32 LB
14254 8" X 8-1/4" L&W 0.34 LB
14263 12" X 8-1/4" L&W 0.39 LB
124642 8" X 1-1/16" L&W 0.18 LB
124643 10" X 1-1/16" L&W 0.2 LB
14506 6" X 1-3/16" L&W 0.16 LB
14508 8" X 1-3/16" L&W 0.18 LB
14225 6" X 1-5/8" L&W 0.17 LB
14227 8" X 1-5/8" L&W 0.19 LB
14229 10" X 1-5/8" L&W 0.21 LB
14342 8" X 5-1/8" L&W 0.27 LB
1-1/4" FLAT FIXED WASHER
Product Code Description Weight
14101 6" X 1-3/16" L&W 0.16 LB
14104 8" X 1-3/16" L&W 0.18 LB
14116 6" X 1-5/8" L&W 0.17 LB
14118 8" X 1-5/8" L&W 0.19 LB
14120 10" X 1-5/8" L&W 0.21 LB
14121 12" X 1-5/8" L&W 0.24 LB
14148 8" X 4-3/4" L&W 0.26 LB
14332 8" X 5-1/8" L&W 0.27 LB
MANUFACTURER
Dayton Superior Corporation
1125 Byers Road
Miamisburg, OH 45342
Customer Service: 888-977-9600
Technical Services: 877-266-7732
Website: www.daytonsuperior.com
Page 2 of 3 File Date: 8/18/2014
Page 3
TECHNICAL DATA SHEET
WARRANTY (ACCESSORIES)
Limited Warranty. Dayton warrants, for a period of 60 days from
the date of shipment (three years from the date of shipment in
the case of formwork, excluding any consumable Products
included with such formwork), that Products and any associated
application drawings and engineering services provided by Dayton
(“Ancillary Services”) will be free from defects in material and
workmanship and, in the case of custom designed formwork, that
the formwork will meet the specifications set forth in the design
drawings approved by Dayton and Customer. Any claim under this
warranty must be made in writing within such warranty period. If
any Product and/or Ancillary Service covered by a timely claim are
found to be defective, Dayton will, within a reasonable time,
make any necessary repairs or corrections or, at Dayton’s option,
replace the Product. Unless pre-authorized by Dayton in writing,
Dayton will not accept any charges for correcting defects or
accept the return of any Product. This warranty will not apply to
any Products that have been subjected to misuse, neglect, storage
damage, misapplication, accident or any other damage caused by
any person other than Dayton, or that have not been maintained
in accordance with Dayton’s specifications. THIS LIMITED
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES AS TO THE
PRODUCTS AND ANCILLARY SERVICES. DAYTON MAKES NO OTHER
WARRANTIES OR GUARANTEES, EXPRESS OR IMPLIED, INCLUDING
ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE. THE REMEDIES SET FORTH
IN THIS SECTION ARE CUSTOMER’S EXCLUSIVE REMEDY FOR
BREACH OF WARRANTY.
A3 STD SNAP TIE
Light Wall Forming
Page 3 of 3 File Date: 8/18/2014
Loading...