Dayton 1RVT8, 1RVT7 User Manual

!

!

!

!

Installation, Operation, Maintenance and Parts Manual

!

!

Please read and save these instructions. This heater must be installed and serviced by trained gas installation and service
personnel only! Read carefully before attempting to assemble, install, operate or maintain the product described. Protect
yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury
and/or property damage! Retain these instructions for future reference.

1RVT7 and 1RVT8

®

Dayton Patio Heaters

Description

Dayton high-intensity patio heaters become highly efficient generators
of infrared radiation by heating a ceramic refractory material to
incandescence. The principal operation is to pass a gas-air mixture
through a perforated ceramic refractory, and ignite it on the refractory
surface. This causes the ceramic material to be heated to approximately
1780°F and generate large amounts of infrared radiation that may be
directed anywhere heat is desired. Infrared radiation heats people and
objects it strikes and not the intervening air. Included is a direct spark
ignition system, manifold pressure tap, porous ceramic grids, a stainless
steel housing and a preset mounting bracket for mounting the heater.
Typical applications are restaurant patios, loading docks, warehouses,
service garages, factories, aircraft hangars, etc.

WARNING

Improper installation, adjustment,
alteration, service or maintenance can
cause property damage, injury or death.

Read and understand the installation,
operating and maintenance instructions thoroughly
before installing or servicing this equipment.

This heater must be installed and serviced by trained
gas installation and service personnel only. Inspect the
heater annually. Failure to comply could result in
personal injury, asphyxiation, death, fire and/or
property damage.

WARNING

Not for indoor residential use.

This heater is not approved for use in

garages, solarium, living quarters, etc. Installation in
residential indoor spaces may result in property
damage, asphyxiation, serious injury or death.

any indoor residential application. This
includes, but is not limited to, attached

store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Maintain clearance to combustibles.

For Your Safety
If you smell gas:

• Shut off gas to the appliance.

• Extinguish any open flame.

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Call your gas supplier. Do not use any phone in your
building.

• Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier,
call the fire department.

Keep these instructions for future reference.

WARNING

Storage of gasoline and other
flammable vapors and liquids in the
vicinity of this or any other appliance
may result in fire or explosion. Do not

Form 5S5668 Printed in U.S.A.

03460
1206/346/VCPVP

®

Dayton Installation, Operation, Maintenance and Parts Manual

®

1RVT7 and 1RVT8

Dayton Patio Heaters

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Warning Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Clearance to Combustibles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Standards, Certifications and Government Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Safety Signs and Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Heater Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Heater Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Gas Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

2

!

!

!

!

!

!

!

Dayton Installation, Operation, Maintenance and Parts Manual

Models 1RVT7 and 1RVT8

Safety

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause property damage,
serious injury or death. Read and understand, the installation, operating and maintenance
instructions thoroughly before installing or servicing this equipment. Only trained, qualified gas
installation and service personnel may install or service this equipment.

Warning Symbols

Safety is the most important consideration during
installation, operation and maintenance of the infra-red
heater. You will see the following symbols and signal
words when there is a hazard related to safety or
property damage.

WARNING

Warning indicates a potentially hazardous situation
which, if not avoided, could result in death or injury.

CAUTION

Caution indicates a potentially hazardous situation
which, if not avoided, could result in minor or moderate
injury.

NOTICE

Applications

This is not an explosion proof heater. Consult your local
Fire Marshall, insurance carrier and other authorities for
approval of the proposed installation.

Commercial / Industrial

Infra-red heaters are designed and certified for use in
industrial and commercial buildings such as outdoor
restaurant patios, warehouses, manufacturing plants,
aircraft hangars and vehicle maintenance shops. For
maximum safety, the building must be evaluated for
potential hazards before installing the heater system. A
critical safety factor to consider before installation is the
clearance to combustibles.

Outdoor Residential

This heater may only be used in outdoor residential
applications and is NOT approved for use in any indoor
residential application. This includes, but not limited to,
attached garages, living quarters, solarium, etc. Consult
the local fire marshal and/or insurance provider if unsure
of your application.

Notice indicates a potentially hazardous situation which,
if not avoided, could result in property damage.

residential indoor spaces may result in property
damage, serious injury or death. In residential
applications this heater may only be used outdoors.

3

WARNING

Not For Indoor
Residential Use.

Installation of a infra-red
heater system in

®

Dayton Installation, Operation, Maintenance and Parts Manual

!

!

!

®

Dayton Patio Heaters

Clearance to Combustibles

1RVT7 and 1RVT8

WARNING

Improperly connected gas lines may result
in serious injury or death, explosion,
poisonous fumes, toxic gases,
asphyxiation. Connect gas lines in
accordance to national, state, provincial
and local codes.

Placement of explosive objects, flammable
objects, liquids and vapors close to the
heater may result in explosion, fire,
property damage, serious injury or death.
Do not store, or use, explosive objects,
liquids and vapor in the vicinity the heater.

Failure to comply with the published
clearances to combustibles could result in
personal injury, death and/or property
damage.

Hazards Include:

For maximum safety the building must be evaluated for
hazards before installing the heater system. Examples
include, but not limited to:

• Gas and electrical lines

• Combustible and explosive materials

• Chemical storage areas

• Areas of high chemical fume concentrations

• Provisions for accessibility to the heater

• Adequate clearances around air openings

• Combustion and ventilating air supply

• Vehicle parking areas

• Vehicles with lifts or cranes

• Storage areas with stacked materials

• Lights

• Sprinkler heads

• Overhead doors and tracks

• Dirty, contaminated environment

A critical safety factor to consider before installation is
the clearances to combustibles. Clearance to
combustibles is defined as the minimum distance you
must have between the infra-red surface, or reflector,
and the combustible item. Considerations must also be
made for moving objects around the infra-red heater.
The following is a partial list of items to maintain
clearances from:

Combustible items include :

• Wood

• Paper

• Fabric

• Chemicals

• Wall or roof insulation

Moving objects include:

• Overhead doors

• Vehicle lifts

• Cranes

• Hoists

• Car wash equipment

When installing the infra-red heater system, the
minimum clearances to combustibles must be
maintained. These distances are shown in Chart 1.1 and
on the minimum clearance to combustibles label
(F/N: LLPCL002) found on the heater. If you are unsure
of the potential hazards, consult your local fire marshall,
fire insurance carrier or other qualified authorities on the
installation of gas fired infra-red heaters for approval of
the proposed installation.

Signs shall be posted specifying the
maximum permissible stacking height in
order to maintain clearances to
combustibles.

CAUTION

4

Dayton Installation, Operation, Maintenance and Parts Manual

Models 1RVT7 and 1RVT8

Chart 1.1 - Clearance to Combustibles in Inches (see Figure 1.1)

Model No.

1RVT7

34,000 [Natural Gas]

1RVT8

34,000 [LP Gas]

Mounting

Angle*

Sides Back Top Below End(s) Front

0° 14 N/A 13 46 22 N/A

30° N/A 8 17 46 22 46

0° 14 N/A 13 46 22 N/A

30° N/A 8 17 46 22 46

* Heaters mounted on an angle between 0° to 30° must maintain clearances posted for 0° or 30°; whichever is greater.

Certain applications (awnings, fabrics, plastics, sprinklers,
insulation) may require the heater to be mounted at a
distance in excess of the published clearances to
combustibles. Contact the factory.

Important! If the heater is mounted beneath a non­combustible surface an 8 in. minimum top clearance
must be maintained from the top of the heater to
prevent overheating the controls.

Figure 1.1 - Clearance to Combustibles

Top

(to ceiling)

Top

(to ceiling)

Back

SideSide

This side down

Below

END VIEW

0° MOUNTING ANGLE

End End

SIDE VIEW

30° MOUNTING ANGLE

Below

END VIEW

Front

30˚

®

5

Dayton Installation, Operation, Maintenance and Parts Manual

®

1RVT7 and 1RVT8

Dayton Patio Heaters

Standards, Certifications and Government Regulations

The installation of this heater must comply with all applicable local, state and national specifications, regulations
and building codes (contact the local building inspector and/or fire marshall for guidance) before installing the
heater system.

In the absence of local codes, the installation must conform to the latest edition of the National Fuel Code ANSI
Z223.1 (NFPA 54).

Refer to the following Standards and codes for application specific guidelines:

Public Garages:

The installation of this heater in public garages must
conform with the Standard for Parking Structures,
ANSI/NFPA 88A (latest edition), or the Standard for
Repair Garages, ANSI/NFPA 88B (latest edition) and
must be at least 8 ft. above the floor.

Aircraft Hangars:

The installation of this heater in aircraft hangars must
conform with the Standard for Aircraft Hangars, ANSI/
NFPA 409 (latest edition). The heater must be installed
at least 10 ft. above the upper wing surfaces and
engine enclosures of the highest aircraft which might
be stored in the hangar. In areas adjoining the aircraft
storage area, the heaters must be installed at least 8 ft.
above the floor. The heaters must be located in areas
where they will not be subject to damage by aircraft,
cranes, moveable scaffolding or other objects.

High Altitude:

The installation of this heater is approved, without
modifications, for elevations up to 6,000 ft. MSL (sea
level). Contact Dayton for installations above these
elevations.

Electrical:

The heater, when installed, must be electrically
grounded in accordance with the National Electrical
Code ANSI/NFPA 70 (latest edition). Under no
circumstances is either the electrical supply line or gas
supply line to provide any assistance in the suspension
of the heater.

Ventilation:

This heater must be installed in accordance with the
requirements set forth in this manual and with the
NFPA 54/ANSI Z223.1 National Fuel Gas Code (latest
edition). See ventilation requirements on page 17.

Dayton® units comply or are certified by one or
more of the following organizations or
standards:

• CSA International Requirement (CSA 2.37/5.90 U.S.).

• American National Standards Institute (ANSI Z83.26).

6

!

CLEARANCE TO COMBUSTIBLES

FIRE HAZARD. Always maintain published clearance to combustibles.

In locations used for the storage of combustible materials, signs must be
posted. Consult manual for additional guidelines.

MODEL NO.

DANGER

SIDE(S) BELOW TOP BEHINDEND(S) FRONT

ALL MODELS

(in millimeters)

MOUNTING

ANGLE

0°

0°

30°

30°

22”

559mm

22”

559mm

14”

356mm

N/A

N/A

46”

1168mm

46”

1168mm

13”

330mm

17”

432mm

N/A

N/A

8”

203mm

N/A

N/A

46”

1168mm

ALL MODELS

(in inches)

Contact may cause burn.
Do NOT touch hot surface.
Allow to cool before
servicing.

This heater must be installed
by qualified personnel only
and in accordance with the
latest edition of the

ANSI/NFPA Standards.
(ANSI/NFPA 88A Parking Structures), 88B
(Repair Garages), 409 (Aircraft Hangars).
Observe all country, state and local codes.

LIGHTING INSTRUCTIONS

1. Rotate heater’s valve knob to “ON” position.

2. Close electrical circuit (usually thermostat).

3. If the heater fails to light, turn “OFF” gas, open electrical circuit and wait 5 minutes
before repeating.

Avoid Serious Injury or
Death. Improper installation,

adjustment, alteration, service
or maintenance can cause

property damage, injury or
death. Read the installation, operation and
maintenance manual thoroughly before
installing or servicing this equipment.

This is not an explosion-proof heater. Where
there is the possibility of flammable vapors or
dusts, consult the local fire marshal, fire
insurance carrier or other authorities for
approval of the proposed installation. Always
maintain minimum ventilation requirements.

30°

This side down

END VIEWSIDE VIEW
0° Mounting

END VIEW

30° Mounting

The minimum end clearance is 22” or 559mm.

!

CLEARANCE TO COMBUSTIBLES

FIRE HAZARD. Always maintain published clearance to combustibles.

In locations used for the storage of combustible materials, signs must be
posted. Consult manual for additional guidelines.

MODEL NO.

DANGER

SIDE(S) BELOW TOP BEHINDEND(S) FRONT

ALL MODELS

(in millimeters)

MOUNTING

ANGLE

0°

0°

30°

30°

22”

559mm

22”

559mm

14”

356mm

N/A

N/A

46”

1168mm

46”

1168mm

13”

330mm

17”

432mm

N/A

N/A

8”

203mm

N/A

N/A

46”

1168mm

ALL MODELS

(in inches)

Contact may cause burn.
Do NOT touch hot surface.
Allow to cool before
servicing.

This heater must be installed
by qualified personnel only
and in accordance with the
latest edition of the

ANSI/NFPA Standards.
(ANSI/NFPA 88A Parking Structures), 88B
(Repair Garages), 409 (Aircraft Hangars).
Observe all country, state and local codes.

LIGHTING INSTRUCTIONS

1. Rotate heater’s valve knob to “ON” position.

2. Close electrical circuit (usually thermostat).

3. If the heater fails to light, turn “OFF” gas, open electrical circuit and wait 5 minutes
before repeating.

Avoid Serious Injury or
Death. Improper installation,

adjustment, alteration, service
or maintenance can cause

property damage, injury or
death. Read the installation, operation and
maintenance manual thoroughly before
installing or servicing this equipment.

This is not an explosion-proof heater. Where
there is the possibility of flammable vapors or
dusts, consult the local fire marshal, fire
insurance carrier or other authorities for
approval of the proposed installation. Always
maintain minimum ventilation requirements.

30°

This side down

END VIEWSIDE VIEW
0° Mounting

END VIEW
30° Mounting

The minimum end clearance is 22” or 559mm.

Maintain Clearances to Combust ibles to Prevent the Risk of Fire.

Clearances to combustibles must be maintained in order to prevent
the ignition of combustible materials. In locations used for the
storage of combustible materials, signs must be posted to specify the
maximum permissible stacking height to maintain the required
clearances from the heater to the combustibles. Signs must either be
posted adjacent to the heater thermostats or in the absence of such
thermostats in a conspicuous location. Clearances ar e provided on
the heater’s safety labels and in the heater’s Installation & Operation
Manual. Refer to applicable ANSI or NFPA-54 Standards or local codes
for further information. Post this tag adjacent to the heater’s
thermostat or controls before operating the heater.

WARNING

AVOID SERIOUS INJURY, DEATH OR PROPERTY DAMAGE.

!

INSTALLER. READ AND POST THIS NOTICE.

Dayton Installation, Operation, Maintenance and Parts Manual

WARNING

OBSERVE

PROPER GAS

DO NOT

ROTATE CONTROL

ASSEMBLY

FOR

GAS TYPE

ONLY

USE TWO
WRENCHES
TO TIGHTEN

Models 1RVT7 and 1RVT8

Safety Signs and Labels

It is important to provide warnings to alert individuals to
potential hazards and safety actions. ANSI Z83.26/CSA

2.37 require you to post a sign “specifying the
maximum permissible stacking height to maintain the
required clearances from the heater to the
combustibles” near the heaters thermostat or in absence
of such thermostats in a conspicuous location.

F/N: LL02 - Observe Proper Gas Type (Natural Gas)
F/N: LL03 - Observe Proper Gas Type (LP Gas)

Top Panel

Safety warning labels must be maintained on the infra­red heater. Illustrations of the safety labels, and their
locations, are pictured below. In locations used for the
storage of combustible materials, signs must be posted
to specify the maximum permissible stacking height to
maintain the required clearances from the heater to
combustibles. Signs must either be posted adjacent to
the heater thermostats or in the absence of such
thermostats in a prominent location.

F/N: LL01 - Clearance Safety Tag
(Affix adjacent to heater’s thermostat).

F/N: LLPCL002
Patio Heater Clearance to Combustibles Label

®

7

!

!

Dayton Installation, Operation, Maintenance and Parts Manual

®

Dayton Patio Heaters

Installation

1RVT7 and 1RVT8

WARNING

Read and understand, the installation,
operating and maintenance
instructions thoroughly before
installing or servicing this equipment.

Only trained, qualified gas installation
and service personnel may install or
service this equipment.

Design

To ensure a safe, properly designed heating system, a
layout should be developed for the correct placement of
the infra-red heater(s). Aside from safety factors such as
clearance to combustibles (see Chart 1.1 on page 5),
you should take into consideration:

• The environment (e.g., is it cold/drafty, average,
protected)?

Note: The effective infra-red surface temperature
of a person or object may be diminished with

• What is the area of heat coverage (e.g., sq. ft.) needed

wind above 5 mph, wind barriers may be required.

(Chart 2.1, Figure 2.2)?

CAUTION

This heater cannot be used in a building with a roof that
is not insulated or where condensation problems can
occur.

This installation manual, along with national, state,
provincial and local codes, address these issues. It is
critical that you read, understand and follow all
guidelines and instructions. Always inspect and evaluate
the mounting conditions, space for exhaust, gas supply
and wiring.

IMPORTANT: Fire sprinkler heads must be located at
an appropriate distance from the heater. This distance
may exceed the published clearance to combustibles.
Certain applications will require the use of high
temperature sprinkler heads or relocation of the heaters.

• Is the heater being used in a social gathering area, or
work station(s)?

• The mounting height of the heater (Chart 2.1, Figure 2.3).

• The type of mounting to be used.

• Physical space needed for the heater (Figure 2.1).

• Gas supply and connections.

• Combustion, ventilating air supply and exhaust path.

• Electricity and wiring to the heater.

Potentially flammable substances, such as Propylene
Glycol or antifreeze solutions, are not to be used in
conjunction with this heater.

For further information consult NFPA 13. Always
observe applicable state and local codes.

8

Dayton Installation, Operation, Maintenance and Parts Manual

Models 1RVT7 and 1RVT8

Figure 2.1 - Patio Heater Dimensions

8.5”

9”

END VIEW

42.25”

SIDE VIEW

Figure 2.2 - Mounting Bracket Extension Dimensions

The heater’s mounting brackets are adjustable in one inch intervals when installed with the connecting arms. All clearance to
combustibles must be maintained. Refer to the minimum and maximum mounting bracket extensions below.

1. Minimum mounting bracket extension to non-combustibles only is 9 in.

2. Minimum 0° mounting bracket extension to combustibles is 14.5 in.

3. Minimum angle mounting bracket extension (up to 30°) to combustibles is 17.5 in.

4. Maximum mounting bracket extension is 20.5 in.

1 2 3 4

®

9

Dayton Installation, Operation, Maintenance and Parts Manual

!

®

Dayton Patio Heaters

Heater Mounting

The heater can be suspended with chains or rigid

WARNING

Improper suspension of the infra-red
heater may result in collapse and persons
being crushed. Always suspend from a
permanent part of the building structure
that can support the total force and
weight of the heater.

threaded rod. Local codes, or conditions such as wind
drafts or other variables can cause movement of the
heater and may require rigid threaded rod. Avoid
excessive movement and/or vibration of the gas
connection by rigidly mounting the heater. The heater
mounting brackets can be used in place of rigid
threaded rods (see Figures 2.5 - 2.6). Consult all
applicable codes before installation.

1RVT7 and 1RVT8

Failure to maintain minimum clearance to
combustibles may result in fire and/or
explosion, property damage, serious
injury or death. Always maintain

minimum clearances and post signs or
provided tags (F/N: LL01) where needed. Signs should
state the hazards for the particular application and be
legible for the building occupants. Consult the factory or
a factory representative for additional information on
signage compliance.

Figure 2.4 - Heater Orientation

Mounting bracket

The heater must be level from side to side and can be
set at an angle between 0° and 30° from horizontal.
The gas connection and power cord must be located on
the lower side (see Figure 2.4).

30°

The gas connection and
power cord must located
towards the lower side
of the heater (towards
the floor).

End

Level end to end

10

End

Dayton Installation, Operation, Maintenance and Parts Manual

Models 1RVT7 and 1RVT8

Chart 2.1 - Recommended Mounting Heights

Recommended

Model & Input

Mounting Height

(Dimension A)

Approximate

Coverage Area

1RVT7, 1RVT8

34,000 BTU/H

Note: This chart is provided as a guideline. Actual conditions
dictate variances from this data.

Figure 2.3 • Recommended Mounting Heights

A

8’-6” to 10’-0” 9’ x 9’

11

®

Dayton Installation, Operation, Maintenance and Parts Manual

®

Dayton Patio Heaters

1RVT7 and 1RVT8

Wall Mounting Bracket

Your patio heater is equipped with preset mounting
hardware. Figures 2.6 and 2.7 illustrate various
mounting configurations using the preset mounting
bracket. This hardware allows the heater to be installed
at an angle between 0° and 30°. This angle must not
exceed 30° from horizontal.

Assemble the mounting hardware as shown in figure 2.5.

The mounting hardware is adjustable in one inch
intervals using the connecting arms Refer to figure 2.2
on page 9 for an illustration of the minimum and
maximum extentions of the mounting bracket.

Figure 2.5 - Mounting Bracket Assembly

Figure 2.6 - Typical Side Wall Mounting

Mounting bracket

attached to wall.

30° Mounting Angle

0° Mounting Angle

30°

Figure 2.7 - Typical Ceiling Mounting

Mounting
bracket attached
to ceiling.

0° Mounting Angle

30° Mounting Angle

30°

12

Dayton Installation, Operation, Maintenance and Parts Manual

!

Models 1RVT7 and 1RVT8

Gas Supply

• Check that the gas piping and service has the capacity

WARNING

Improperly connected gas lines may result in fire,
explosion, poisonous fumes, toxic gases, asphyxiation
and death. Connect gas lines in accordance to
national, state, provincial and local codes.

to handle the load of all heaters being installed, as well
as any other gas appliances being connected to the
supply line.

• Check that the main gas supply line is of proper
diameter to supply the required fuel pressures.

• If utilizing used pipe, verify that its condition is clean
and comparable to a new pipe. Test all gas supply lines
in accordance with local codes.

The gas supply to the infra-red heater must be
connected and tested in accordance with national, state,
provincial and local codes along with the guidelines in
this manual. Refer to the latest edition of the ANSI
Z223.1 (NFPA 54) Standard.

Important! Before connecting the gas supply to the
infra-red heater(s):

• Check for conditions such as drafts or other variables
which might cause excessive movement of the unit
and cause damage to the gas connection. Ensure that
the unit is securely mounted and connect the gas with
an approved connection device suitable for the
environment of use.

Chart 2.2 - Manifold Pressure

Type of Required Manifold Minimum Inlet Maximum Inlet
Gas Pressure Pressure Pressure

• Test and confirm that inlet pressures are correct. Refer
to the rating plate for required minimum and
maximum pressures (see Chart 2.2). The gas supply
pipe must be of sufficient size to provide the required
capacity and inlet pressure to the heater (if necessary,
consult the local gas company).

• For test pressures in excess of 1/2 psig (3.5 kPa), the
heater and ball shutoff valve must be disconnected
from the gas supply piping system during any pressure
testing of the system.

• For test pressures equal to or less than 1/2 psig (3.5
kPa), the heater must be isolated from the gas supply
piping system by closing it’s individual manual shutoff
valve during any pressure testing of the gas supply
piping system.

Natural 5.0 in. W.C.P. 6.0 in. W.C.P. 14.0 in. W.C.P.

Liquefied Petroleum 10.0 in. W.C.P. 11.0 in. W.C.P. 14.0 in. W.C.P.

Note: Check manifold pressure at the tap on the ball shutoff valve. Readings will be above atmospheric

pressure during operation.

Pressure Equivalents: 1 in. W.C.P. equals .058 oz./sq. in. equals 2.49 Mbar.

®

13

Dayton Installation, Operation, Maintenance and Parts Manual

!

!

!

!

®

Dayton Patio Heaters

To connect the gas:

4. Attach the gas connector (field supplied) to the

WARNING

1RVT7 and 1RVT8

adapter and the heater’s gas inlet. Seal the joints.

Failure to install, operate or service
this appliance in the approved manner
may result in property damage, injury

or death. This heater must be installed
and serviced by trained gas installations and service
personnel only.

The installation of this heater must conform with local
building codes or, in the absence of such codes, the
National Fuel Code (NFPA 54).

The gas outlet must be in the same room as the
appliance and accessible. It may not be concealed within
or run through any wall, floor or partition.

1. Install a sediment trap / drip leg if condensation may
occur at any point of the gas supply line. This will
decrease the possibly of loose scale or dirt in the
supply line entering the heater’s control system and
causing a malfunction. NOTE: High pressure gas
above 14 in. W.C.P. (water column pressure) requires
a high pressure regulator and ball valve (field
supplied).

2. A stainless steel flexible hose (field supplied) formed
into a smooth C-shape is recommended. If local
codes prohibit the use of a gas hose, then a swing
joint may be used.

3. Attach the ball valve (field supplied) to the gas
supply pipe. Apply pipe compound to NPT adapter
threads to seal the joint. Use only a pipe compound
resistant to liquid petroleum.

Note: Provide a 1/8 in. NPT plugged tapping

accessible for test gauge connection immediately
upstream of gas connection to the heater (provided
on ball valve, when supplied).

Important! The fittings (nuts) on the flexible

connector (field supplied) must be connected to an
adapter. They may not be directly connected to the
gas supply pipe.

Excessive torque on the manifold may misalign the

orifice. Always use two wrenches to tighten
mating pipe connections.

5. Final assembly must be tested for gas leaks
according to NFPA or local codes.

WARNING

Testing for gas leaks with an open flame
or other sources of ignition may lead to a
fire or explosion and cause serious injury
or death. Test in accordance with NFPA
or local codes.

To disconnect the gas:

1. Disconnect the power to the heater.

2. Turn off the gas supply to the heater and “bleed”

the gas line.

3. Using two wrenches, slowly loosen the fittings.
Excessive torque on the manifold may misalign the
orifice.

4. Inspect the hose and fittings for abrasion, wear or
damage. Replace if necessary.

14

Dayton Installation, Operation, Maintenance and Parts Manual

!

!

!

!

Models 1RVT7 and 1RVT8

WARNING

Failure to disconnect the electricity to
the heater before disconnecting the gas
supply may result in explosion, fire,
property damage, injury or death.

Figure 2.8 - Gas Connection

(shown installed with a flexible hose)

Regulator

(field supplied

when required)

(field supplied)

Elbows

WARNING

Conditions such as wind drafts or other
variables can cause movement of the
heater and may require it to be rigidly

mounted. Avoid excessive movement
and/or vibration of the gas connection by rigidly
mounting the heater.

Shut off valve / inlet tap

Mounting
bracket

Shut off valve

(field supplied)

Drip leg / Sediment trap

(field supplied)

Stainless steel gas
connector (field
supplied), formed
into smooth C-shape
is recommended.

®

15

Dayton Installation, Operation, Maintenance and Parts Manual

!

®

Dayton Patio Heaters

Electrical Requirements

1RVT7 and 1RVT8

WARNING

Incorrect or improper wiring may result in
shock, injury or death. Field wiring to the
heater must be connected and grounded in
accordance with national, state, provincial,

local codes and to the guidelines in this
manual. Refer to the most current revisions to the ANSI/
NFPA 70 Standard.

Control systems are initiated by 120V control voltage.
Important! Proper grounding and polarity are essential.
If the system is not properly grounded, it cannot
determine the presence of a flame and will lockout and
shut off.

Figure 2.9 - 120V Typical Field Wiring

Mounting

bracket

NOTICE

Radiant heat may damage the flexible power cord.
Always keep the flexible power cord away from the
heater. Do not allow the power cord to be subjected to
radiant heat.

For wiring of controls see Figure 2.9 below. It is
recommended that the control be installed on the hot
side of a fused supply line and have a sufficient ampere
capacity rating for the heater(s) it will control (see
Figures 3.1 & 3.2).

120V thermostat,
timer or switch
(field supplied)

Hot

Neutral

Heater

16

Dayton Installation, Operation, Maintenance and Parts Manual

!

Models 1RVT7 and 1RVT8

Ventilation

displacement is required. A balanced system is essential

WARNING

Improper or insufficient
ventilation may result in
explosion, fire, health
problems, carbon

monoxide poisoning or
death. Vent enclosed spaces and buildings according to
national, state, provincial and local codes.

This infra-red heater must be vented in accordance with
national, state, provincial and local codes and the
guidelines throughout this manual. Refer to the latest
edition of the ANSI Z223.1 (NFPA 54) Standard.

It is required that the upper levels of the space to be
heated are properly ventilated to supply combustion
air to the heaters and to sufficiently dilute the products
of combustion. It is also important to keep the flue
discharge area clear of gas piping and electrical wiring
(see Figure 2.10).

to avoid negative building pressure which causes
excessive infiltration, unfavorable drafts and affects
combustion efficiency.

Air displacement may be accomplished by either gravity
or mechanical means. Mechanical exhausters are
preferred and typically mounted at high points on the
roof over where stagnant air accumulates inside. For
a flat roof, considerations of prevailing winds, high and
low pressure areas, and distribution of air movement
must be taken into consideration when locating
exhausters.

Best air distribution is accomplished by using a number
of small exhausters versus one large exhauster. Provide
a minimum of one square inch of inlet area per 1000
BTU/H for combustion air supply. Inlet opening in the
building should be well distributed, located high on the
wall and should direct incoming air upward to dilute
products of combustion while preventing drafts at lower
levels. Inlets are typically 1 to 3 sq. ft.

Provisions must also be made to provide sufficient fresh
air intake area and exhaust air outlet area. Natural or
mechanical means shall be provided to supply and
exhaust at least 4.0 CFM per 1000 BTU/H of gas input.
Exhaust openings for the removal of flue products must
be above the level of the heater(s).

Where insufficient air movement exists, induced air

Figure 2.10 - Hot Flue Discharge

Discharge released from side
air channels. Keep area clear
of gas piping and electrical
wiring.

In certain applications, local codes may require that
mechanical exhaust systems be interlocked with the
heaters to enable both to function simultaneously or
allow control of exhausters with a ceiling mounted
humidistat.

®

17

Dayton Installation, Operation, Maintenance and Parts Manual

!

®

Dayton Patio Heaters

Operation

Sequence of Operation:

WARNING

Improper operation of
the heater may result in
explosion, fire, shock and
carbon monoxide

poisoning. Follow all
guidelines and warnings in this manual and national,
state, provincial and local codes. Always conduct safety
checks before operating the heater. Do not operate the
heater in unsafe conditions.

Important! Before operating the heater, conduct
the following safety procedures:

• Check for any possible gas leaks.

• Alert all persons about the hazards of high surface
temperature and to keep a safe distance away in
order to avoid burns and possible clothing ignition.

• Provide supervision when young children are in the
area of the heater.

• Check to make sure clothing isn’t hung from the
heater and that flammable materials are not placed
on or near the heater.

Starting Circuit:

When voltage is applied to L1 and L2, a circuit is
completed from L1 via the blower motor to L2. The
blower fan is mounted in the control box and rated to
supply sufficient air for combustion. Air pressure
generated by the blower will cause the normally open
pressure switch to close. Another circuit is completed
from L1 to the spark ignition module and back to L2.
After a seven (7) second pre-purge, the spark electrode
and gas valve are energized simultaneously. The trial for
ignition is fifteen seconds.

Running Circuit:

After ignition, the flame rod monitors the flame. As long
as a flame is present, the valve is held open. If the flame
is lost, the control acts to close the valve within one
second, and a new trial sequence identical to that at
start-up is initiated. If proof of flame is not established
within the 15 second trial for ignition, the unit will retry
two additional times before entering lockout mode. If
lockout occurs, the control can be reset by briefly
interrupting the power source.

1RVT7 and 1RVT8

• Check that all guards or protective devices are in place
and secure.

• Check the hose assembly for excessive abrasion, wear
or damage. If necessary replace.

• Check control compartment, burners and circulating
air passages for debris. If necessary, clean the debris.

18

Dayton Installation, Operation, Maintenance and Parts Manual

Models 1RVT7 and 1RVT8

Lighting Instructions:

1. Rotate heater’s valve knob to “ON” position.

2. Close electrical circuit (usually thermostat).

3. If the heater fails to light, turn “OFF” gas, open

electrical circuit and wait 5 minutes before
repeating.

Shutdown Instructions:

1. Open electrical circuit (usually thermostat).

2. Turn off electrical power if service is to be

performed.

3. Rotate heater’s valve knob to “OFF” position.

Wiring Diagrams

Figure 3.1 - 120V

Amp draw:
.25 starting
.24 running

19

®

Dayton Installation, Operation, Maintenance and Parts Manual

!

®

Dayton Patio Heaters

Maintenance

1RVT7 and 1RVT8

WARNING

Always wear clothing that protects the
body and use protective glasses when
maintaining the heater.

Electrical shock or explosion may occur
when conducting maintenance while
the heater is connected to the power
source and gas supply. Disconnect
power and gas supply to heater before
servicing.

Burner malfunction may result in
explosion or fire. Never operate the
heater if there are any signs of
malfunction, excessive wear or damage.
Call a professional for assistance.

Before each use:

• Check the gas supply line and hose assembly for

any possible leaks or damage.

• Check heater elements for debris. Visually check

burner flames.

NOTICE

Cleaning the heater elements with high pressure air may
cause damage to the elements and equipment failure.
Do not blow out heating elements with high pressure
air.

Before conducting maintenance on the heater
disconnect the power and gas supply. When pressure
testing the gas supply piping system follow these
guidelines:

• At a test pressure in excess of 1/2 psig (3.5 kPa) the

heater and ball shutoff valve must
be disconnected from the gas supply piping system
during any pressure testing of the system.

• At a test pressure equal to or less than 1/2 psig (3.5

kPa) the heater must be isolated from the gas
supply piping system by closing it’s individual
manual shutoff valve during any pressure testing
of the gas supply piping system.

Cleaning the main burner:

• Keep the heated area clear and free of combustible
materials, gasoline and flammable vapors and
liquids. Ensure there is no obstruction of the flow of
combustion and ventilation.

Periodic maintenance:

• Clean the heater with cleaning agents suitable for
the unit’s construction materials (i.e., stainless steel
cleaner).

• Lubricate moving parts.

• Inspect the gas supply piping system for signs of
corrosion or failure. Replace if necessary.

1. Gently use an air hose to blow any accumulated
dust and/or dirt off the heater. Air hose pressure
should not exceed 30 psig.

2. Gently, pass the air hose over the entire exposed
area of the ceramic. A distance of 2’ to 4’ from
the unit is recommended.

3. Gently place the air hose outlet into the venturi
tube and allow the air to flow for approximately
one minute.

During long periods of non-usage, remove or cover
heater with a polyethylene bag and shut off gas supply.
If further service to the heater is desired, contact your
representative or the factory.

20

Dayton Installation, Operation, Maintenance and Parts Manual

Models 1RVT7 and 1RVT8

Chart 4.1 - Troubleshooting Guide

Symptom Possible Cause Corrective Action

Burning of gas-air mixture inside
plenum (flashback).

Delayed ignition. • Electrode out of specification.

Low ceramic surface
temperature or excessive
rollout.

Control system overheating. • Heater not mounted correctly.

Gas odor. • Loose pipe connection. • Check connections. Tighten as necessary.

Heater cycles repeatedly. • Heater located in drafty area.

No spark; no ignition. • Lack of 120V incoming voltage.

Heater lights, and “locks out”
after approximately 10 seconds.

Spark is present. No main gas
operation. Unit “locks out”.

Heater will not shut off. •Defective thermostat or wiring.

• Heater mounted at incorrect angle.

• Excessive drafts.

• Gas leaking at orifice.

• Separation of ceramic grids.

• Ceramic grids cracked.

• Low gas pressure.

• Partially blocked orifice.

• Improper orifice size.

• Incorrect gas.

• Dirty or plugged burner ceramics.

• Partially blocked orifice.

• Low inlet gas pressure.

• High or low manifold gas pressure.

• Foreign matter in venturi tube.

• Excessive dark spots on burner.

• Gas supply piping too small.

• Incorrect gas.

• Heater mounted too close to ceiling.

• Low gas pressure.

• Thermostat located in drafty area.

• Defective electrode or circuit board.

• Open high voltage wire.

• Fan not operating.

• Improper electrode gap.

• Loose or open wire connection.

• Pressure switch not satisfied.

• Poor or no equipment ground.

• Unit in “safety lockout” mode.

• Defective “gaslighter” control.

• Poor or no equipment ground.

• Polarity is reversed.

• Low gas pressure.

• Electrode not sensing.

• Heater mounted at incorrect angle.

• Defective “gaslighter” control.

• Gas valve in “OFF” position.

• Defective gas valve.

• Defective “gaslighter” control.

• Gas valve stuck or open.

• High gas pressure.

• Mounting angle 0˚- 30˚.

• Relocate or shield from draft.

• Check with leak detector solution.

• Replace burner.

• Replace burner.

• See ignition system insert.

• See Section 2.0, Gas Supply.

• Clean or replace.

• Consult Dealer.

• See unit nameplate.

• See periodic maintenance instructions.

• Remove and clean.

• See Section 2.0, Gas Supply.

• Adjust main valve regulator as specified.

• See periodic maintenance instructions.

• See periodic maintenance instructions.

• Increase inlet pressure or replace piping.

• See unit nameplate.

• Mounting angle 0˚- 30˚. Level left to right.

• Observe clearance to combustibles.

• Relocate or shield from draft.

• See Section 2.0, Gas Supply.

• Relocate thermostat.

• Replace.

• Check power supply.

• Isolate an ohm for resistance, replace if 0.

• Locate source of electrical problem or
replace faulty fan.

• See Ignition System specifications.

• Check all wires, tighten or replace.

• Verify fan operation. Remove obstructions.

• Check all connections, provide positive
earth ground.

• Interrupt power source, repeat trial for ignition.

• Replace.

• Check all connections, provide positive
earth ground.

• 120V to black, neutral to white.

• See Section 2.0, Gas Supply.

• Relocate or replace if defective.

• Mounting angle 0˚- 30˚.

• Replace.

• Turn to “ON” position.

• Isolate and check for resistance, replace if 0.

• Replace.

• Replace or repair.

• Replace.

• See Section 2.0, Gas Supply.

21

®

56

4

1RVT7 and 1RVT8

53

50

7

55

54

3

38

59

57

33

2

Repair Parts Illustration for Dayton Patio Heater

57

45

44

42

36

24

25

37

28

48

49

7

58

16

15

35

34

30

20

14

12

46

32

31

29

6

27

5

22

26

21

23

13

1

18

10, 11

60

54

51

47

52

43

17

41

56

19

40

Dayton Installation, Operation, Maintenance and Parts Manual

For Repair Parts, call 1-800-323-0620

24 hours a day - 365 days a year

Please provide following information:

-Model number

-Serial number (if any)

-Part description and number as shown in parts list

22

9

8

39

55

1RVT7 and 1RVT8

Description Part No. Quantity Ref.No. Description Part No. Quantity

Ref.

No.

1 Valve Mounting Base PH-108 1 31 Brass Fitting PH-164 1

2 Egg Crate PH-111 1 32 Plastic Gas Valve 90° Vent PH-159 1

Dayton Installation, Operation, Maintenance and Parts Manual

Repair Parts List for Dayton Patio Heater

3 Egg Crate Frame w/ Flashshield PH-112 1 33 Burner Assembly w/ Hold Downs & Footings PH-170 1

4 Egg Crate Assembly w/ Frame & Nutsert PH-113 1 34 Valve Mounting Bracket PH-171 1

5 120V Fan PH-115 1 35 Valve Mounting Panel PH-172 1

6 Fan Mounting Panel PH-116 1 36 Weather Stripping PH-121 2

7 Air Distribution Panel PH-117 1 37 Burner & Electrode Mounting Panel PH-174 1

8 120 Volt Flexible Three-prong Cord PH-133 1 38 Burner End Mounting Panel (SS) PH-178 1

9 Strain Relief PH-137 1 39 5/16” x 3/4” HEX HD PH-190 8

10 Gas Valve - Natural Gas PH-140 1 40 5/16” Split Washer Zinc PH-191 8

11 Gas Valve - LP Gas PH-141 1 41 5/16” Hex Nut PH-192 8

12 3/8” Closed Pipe Nipple PH-142 1 42 #1/4-20 Square Cagenut PH-193 1

13 3/8” Reducer Fitting PH-143 1 43 Control Cover Thumbscrew PH-194 1

14 Gas Orifice PH-144 1 44 5/16”-18 x 1-1/2” Gold Nutsert Bolt PH-195 1

15 9/16” Ext. Lock Washer PH-145 1 45 #1/4”-20 x 1/2” Machine Bolt PH-180 3

16 9/16”-18 Hex Jam Nut PH-146 1 46 #1/4”-20 Hex Nut PH-181 3

17 3/8”x 5” Incoming Pipe Nipple PH-147 1 47 Control Cover Hinge Rod PH-196 1

18 3/8” Ball Valve/Inlet Tap PH-148 1 48 Top Panel (SS) PH-201 1

19 Rubber Inlet Grommet PH-149 1 49 Left Frame Side Panel (Gas & Electric) (SS) PH-202 1

20 Ignitor Electrode PH-150 1 50 Right Frame Side Panel (SS) PH-203 1

21 Circuit Board (MARK 10DX-117) PH-151 1 51 Control End Panel w/ Louvers & Hinge (SS) PH-204 1

22 100-900 Harness (DRWH-120) PH-152 1 52 Control Box Cover w/ Hinge (SS) PH-205 1

23 Controls Mounting Panel PH-153 1 53 End Panel (SS) PH-206 1

24 12” Orange High voltage Wire w/ Boot PH-155 1 54 Hanging Bracket (SS) PH-297 2

25 2-Way Red Crimp Connector PH-156 1 55 Mounting bracket (SS) PH-298 2

26 Thermal Fuse PH-157 1 56 Mounting Bracket Connecting Arm (SS) PH-299 2

27 Door Switch PH-158 1 57 Rain Guard (SS) PH-210 2

28 Pressure Switch PH-161 1 58 #8 x 1/2” SLTD HW Screw (SS) PH-282 1

29 Short Vinyl Hose PH-162 1 59 5/8” Black Inlet Pressure Tap Grommet PH-122 1

30 Long Vinyl Hose PH-163 1 60 3/4” Black Plastic Inlet Cap PH-130 1

®

23

Dayton Installation, Operation, Maintenance and Parts Manual

®

1RVT7 and 1RVT8

Dayton Patio Heaters

Limited Warranty

One-Year Limited Warranty. Patio Heaters covered in this manual, are warranted by Danyotn Electric Mfg. Co.

(Dayton) to the original user against defects in workmanship or materials under normal use for one year after date
of purchase. Any part which is determined to be defective in material or workmanship and returned to an
authorized service location, as Dayton designates, shipping costs prepaid, will be, as the exclusive remedy, repaired
or replaced at Dayton’s option. For limited warranty claim procedures, see PROMPT DISPOSITION below. This
limited warranty gives purchasers specific legal rights which vary from jurisdiction to jurisdiction.

Additional Limited Warranty. In addition to the above mentioned one-year warranty, Dayton warrants the original
purchaser an additional two-year extension on the ceramic burner. This extension excludes electrical/purchased
components.

Limitation of Liability. To the extent allowable under applicable law, Dayton’s liability for consequential and
incidental damages is expressly disclaimed. Dayton’s liability in all events is limited to and shall not exceed the
purchase price paid.

Warranty Disclaimer. Dayton has made a diligent effort to provide product information and illustrate the products
in this literature accurately; however, such information and illustrations are for the sole purpose of identification,
and do not express or imply a warranty that the products are merchantable, or fit for a particular purpose, or that
the products will necessarily conform to the illustrations or descriptions. Except as provided below, no warranty or
affirmation of fact, expressed or implied, other than as stated in the “LIMITED WARRANTY” above is made or
authorized by Dayton.

Product Suitability. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or
use of products for certain purposes, which may vary from those in neighboring areas. While Dayton attempts to
assure that its products comply with as many codes, it cannot guarantee compliance, and cannot be responsible for
how the product is installed or used. Before purchase and use of a product, review the product applications, and all
applicable national and local codes and regulations, and be sure that the product, installation, and use will comply
with them.

Certain aspects of disclaimers are not applicable to consumer products: e.g., (a) some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you: (b) also, some jurisdictions do not allow a limitation on how long an implied warranty lasts, consequently
the above limitation may not apply to you: and (c) by law, during the period of this limited warranty, any implied
warranties of implied merchantability or fitness for a particular purpose applicable to consumer products purchased
by consumers, may not be excluded or otherwise disclaimed.

Prompt Disposition. Dayton will make a good faith effort for prompt correction or other adjustment with respect
to any product which proves to be defective within limited warranty. For any product believed to be defective
within limited warranty, first write or call dealer from whom the product was purchased. Dealer will give additional
directions. If unable to resolve satisfactorily, write to Dayton at address below, giving dealer’s name, address, date
and number of dealer’s invoice, and describe the nature of the defect. Title and risk of loss pass to buyer on delivery
to common carrier. If product was damaged in transit to you, file claim with carrier.

Manufactured for Dayton Electric Mfg. Co., 5959 W. Howard St., Niles, Illinois 60714 U.S.A.

Manufactured for Dayton Electric Mfg. Co.
Niles, Illinois 60714 U.S.A.

24

®