Page 1
(888) IPD-CONVerters
●
(888) 473-2668 ● www.ipdconverters.com
XWS SERIES - 150 WATT
DESCRIPTION FEA TURES
XWS DC/DC converters are high-powered converters
which cover a wide range of industrial and general
applications. Available input voltages include 12V, 24V,
40V, and 48V; output voltages are available from 5V to
24V. The XWS features remote sense leads for accurate
point of load regulation, and has short circuit and
overcurrent protection. For dual and triple output high
power solutions, see the XWD and XWT series of
converters, respectively.
TECHNICAL SPECIFICA TIONS
Input
Voltage Range
12 VDC Nominal 10 - 20 VDC
24 VDC Nominal 18 - 36 VDC
40 VDC Nominal (Wide Input) 20 - 60 VDC
48 VDC Nominal 36 - 72 VDC
Input Ripple Current 20% Iin Max.
Reverse Input Current 100% Iin Max.
Output
Setpoint Accuracy ±1%
Line Regulation Vin Min. - Vin Max., I
Load Regulation I
Min. - I
out
out
Minimum Output Current 10 % l
Dynamic Regulation, Loadstep 25% I
Pk Deviation 4% Vo
Settling Time 500 µs
Voltage Trim Range ±10%
Current Limit Threshold Range, % of I
Short Circuit Protection Continuous
OVP All Models
Turn-On Time 10 ms
Remote Shutdown TTL And CMOS Compatible, Positive Logic
Switching Frequency 200 kHz
Isolation
Input - Output 500 VDC
Temperature Coefficient ±0.02%/°C
Case Temperature
Operating Range -25 To +85°C
Storage Range -40 To +125°C
Thermal Shutdown Range 105 To 115°C
Humidity Max., Non-Condensing 95%
Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz
MTBF† (Bellcore TR-NWT-000332) Consult Factory
Safety Consult Factory
Weight (Approx.) 15.4 oz
Rated ±0.2% V
out
Max., Vin Nom. ±1% V
rated
out
Rated 110 - 130%
out
General
• High Power Package
• Wide Input Range
• Trim and Enable Pins
95
90
85
EFFICIENCY %
80
75
10 20 30 40 50 60 70 80 90 100
95
out
out
out
††
90
85
80
EFFICIENCY %
75
70
65
10 20 30 40 50 60 70 80 90 100
†
MTBF predictions may vary slightly from model to model.
††
Industrial temp range available
Specifications typically at 25°C, normal line, and full load, unless otherwise stated.
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult factory
for specific model information.
• Remote Sense Pins
• 500V Isolation
• Short Circuit Protection
Efficiency vs. Load (24V Input)
XWS2415
LOAD %
Efficiency vs. Load (48V Input)
XWS4805
XWS4815
LOAD %
Notes
C48
Page 2
XWS SERIES - 150 WATT
MODELS - (See the last page of this file for options.)
Vin
(Volts)
12
12
12
12
24
24
24
24
48
48
48
48
40
40
40
40
Vin Range
(Volts)
10 - 20
10 - 20
10 - 20
10 - 20
18 - 36
18 - 36
18 - 36
18 - 36
36 - 72
36 - 72
36 - 72
36 - 72
20 - 60
20 - 60
20 - 60
20 - 60
Iin Max.*
(Amps)
13.9
16.9
16.7
15.7
10.9
12.9
12.8
13.6
5.5
6.5
6.5
6.8
10.3
12.4
12.2
12.9
* Maxi mum input curre nt at mi ni mum inp ut v o l tage, max i mum rate d output p o wer.
** At nominal Vin, rated output.
MECHANICAL DRAWING
5.50"
(139.7mm)
#4-40 THREADED INSERTS 4PLS.
1
2
3
3.50"
(88.9mm)
(-15.2mm)
-0.60"
4
5
6
7
0
DIA 0.040" 13PL.
BOTTOM VIEW
(1.0mm)
Vout
(Volts)
5
12
15
24
5
12
15
24
5
12
15
24
5
12
15
24
Iout Rated
(Amps)
10.4
8
9
10
11
12
13
14
4.300"
(109.2mm)
8.3
Rip p le & No ise
Pk-Pk (mV)
20
50
120
150
5
30
15
12
8
30
15
12
8
30
15
12
8
240
50
120
150
240
50
120
150
240
50
120
150
240
Efficiency
Typ. **
79%
81%
82%
84%
83%
85%
86%
86%
82%
85%
85%
86%
80%
80%
81%
82%
Model
XW S1 20 5
XW S1 21 2
XW S1 21 5
XW S1 22 4
XW S2 40 5
XW S2 41 2
XW S2 41 5
XW S2 42 4
XW S4 80 5
XW S4 81 2
XW S4 81 5
XW S4 82 4
XW S6 00 5
XW S6 01 2
XW S6 01 5
XW S6 02 4
Thermal Impedance
Natural Convection 2.5 °C/W
100 LFM 2.1 °C/W
200 LFM 1.7 °C/W
300 LFM 1.3 °C/W
400 LFM 1.1 °C/W
Note:
2.625"(66.7mm)
2.250"(57.2mm)
1.875"(47.6mm)
1.500"(38.1mm)
1.125"(28.6mm)
0.750"(19.1mm)
0.375"(9.5mm)
0
-0.375"(-9.5mm)
-0.625"(-15.9mm)
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated for
specific application.
Pin Function
1 No Pin
2 -V
3 -V
4 +V
5 +V
6 Enable
in
in
in
in
7 Case
8 -V
9 -V
10 +V
11 +V
12 - Sense
out
out
out
out
13 Trim
14 + Sense
Tolerances
Inches: (Millimeters)
.XX ± 0.040 .X ± 1.0
0.92"
(23.4mm)
.XXX ± .010 .XX ± 0.25
Pin:
± 0.002 ± 0.05
C49
Page 3
MECHANICAL DRAWING
(888) IPD-CONVerters
XWS SERIES - 150 WATT
TERMINAL STRIP OPTION
●
(888) 473-2668 ● www.ipdconverters.com
#4-40 THREADED INSERTS 4PLS.
2
3
4
5
6
7
4.300"
(109.22mm)
5.50"
(139.7mm)
PIN VIEW
DIA 0.041" 13PLS.
(1.04mm)
81
9
10
11
12
13
14
0.375" EA.
(9.53mm)
3.50"
(88.90mm)
3.000"
(76.20mm)
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES:
.X }.030
.XX }.040
.XXX }.010
FRACTION }.030
0.52"
(13.2mm)
0.92"
(23.4mm)
DIA 0.18"
(4.6mm)
0.25"
(6.4mm)
C50
Page 4
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that
you prefer and add them to the model number. Example ordering options are located below the
options table.
OPTION SUFFIX APPLICABLE SERIES REMARKS
Negative Logic N HAS, HBD, HBS, HES, LES, QBS,
Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES
Terminal Strip TS XWS, XWD, XWT
Trim 1 IAS, LES
Enable 2 I A D, IAS, LES, SMS
Trim and Enable 3 I AS, LES
Current Share 4 S MS
Headerless Y Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK
OPTIONS
0.110” (2.8mm) Pin Length 8 All Units (Except SMS)
0.150” (3.8mm) Pin Length 9 All Units (Except SMS)
0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM
0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM
0.45” (11.4mm) Horizontal
Heatsink
0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM
0.95” (24.1mm) Horizontal
Heatsink
0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM
2H All Units (Except DIP, SIP, and SM
3H All Units (Except DIP, SIP, and SM
QES, TES, TQD
Packages)
Packages)
Packages)
Packages)
Packages)
Packages)
TTL “Low” Turns Module ON
TTL “High” Turns Module OFF
Standard Pin Length is 0.180”
(4.6mm)
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and
0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
C105
Loading...