Danfoss AMV 25, AMV 35 Data sheet

Data sheet

Actuators for three point control

AMV 25, AMV 35

Description

Ordering

AMV electric actuators are used with, VRB, VRG, VF, VL valves with additional adapter

(Code No. 065Z0311, not supplied) and VFS 2 valves up to DN 50 diameter.

Actuators

Typ e

AMV 25 230 082G3024

AMV 25 24 082G3023

AMV 35 230 082G3021

AMV 35 24 082G3020

Supply voltage

(VAC )

Code No.

The actuator automatically adapts its stroke to valve end positions which reduces commissioning time. Optional auxiliary switches, feedback potentiometer and valve stem heater are available.

The actuator has some special features:

• The advanced design incorporates load related ‘switch-off’ to ensure that actuators and valves are not exposed to overload;

• Digitale feedback end position indication signal for valve end position is available by terminal 4 or 5;

• Low weight and robust;

Main data:

• Nominal voltage:

- 24 VAC, 50 Hz/60 Hz

- 230 VAC, 50 Hz/60 Hz

• Control input signal:

3 point

• Force: 450 N

• Stroke: 15 mm

• Speed: 15 s /mm

• Max. medium temperature: 150 °C

• End-position signals

Accessories

Typ e Code No.

Additional switch (2×) 082H7015

Additional switch (2×) and potentiometer (10 kΩ)

Additional switch (2×) and potentiometer (1 kΩ)

Adapter for VFS 2 valves DN 15-50 (for media temp. over 150 °C)

Stem heater (for valves DN 15-50) 06 5B2171

Adapter for valves VRB/ VRG/VF/VL (2009) DN 15-50

Clutch AMV(E) 25, AMV(E) 35

* Need to be orde red separately.

082 H7016

08 2H7017

065Z 7548

06 5Z03 11*

003G6396

Technical data

Typ e AMV 25 AMV 35

Power supply V 24 AC, 230 AC; +10 to –15 %

Power consumption VA 2 7

Frequency Hz 50/60

Control input 3-point

Closing force N 1000 600

Max. stroke mm 15

Speed by 50 Hz (60 Hz) s/mm 11 (8, 8) 3 (2,4)

Max. medium temperature

Ambient temperature 0 … 55

Storage and transport temperature –40 … 70

Grade of enclosure IP 54

Weight kg 1,55

- marking in accordance with standards

°C

150 (200 - with adapter or mounted horizontally)

Low Voltage Directive 73/23/EEC,

EMC-Directive 2006/95/EEC: EN 60730-1, EN 60730-2-14

Data sheet Actuators for three point control AMV 25, AMV 35

Installation

≤150°C for AMV 25, 35

max

and VRB, VRG, VF and VL

= 200°C for AMV 25, 35

max

and VFS

≤150°C for AMV 25, 35

max

and VFS

Adapter for VFS (Code No.065Z7548)

≈5

Mechanical

Use 4 mm Allan key (not part of actuator delivery) to mount actuator on the valve. Installation of the valve with the actuator is allowed in horizontal position or upwards. Installation downwards is not allowed.

The actuator must not be installed in an explosive atmosphere, at ambient temperature lower than 0 °C or at ambient temperature higher than 55 °C. It must not be subject to steam jets, water jets or dripping liquid as well.

Note: the actuator may be rotated up to 360° with respect to the valve stem by loosening the retaining fixture. Once the actuator is placed, retighten the fixture.

≈5

Electrical

Electrical connections can be accessed by removing the actuator cover. Two cable gland entries with thread (M20 x 1.5 and M16 x 1.5) are prepared for cable glands.

Note: Cable and cable gland used must not compromise the actuator’s IP rating, and must ensure the connectors are fully strain relieved. Please observe local rules and regulations as well.

Disposal The actuator must be dismantled and the

elements sorted into various material groups before disposal.

+ 2 hidden pages