Data sheet
Actuators for three point control
AMV 130, AMV 140, AMV 130H, AMV 140H
DH-SMT/SI VD.KG.Y1.02 © Danf oss 06/2006 1
Description AMV 130/140 and AMV 130H/140H actuators are
used with VZ, VZL and VRBZ valves. The actuator
can be used with fan coil units, induction units,
small reheaters, recoolers and zone applications
in which hot/cold water is the controlled
medium.
Main data:
• 3-point versions
• Force switch-off at stem down position
prevents overload of actuator and valve
• No tools required for mounting
• Maintenance free during lifetime
• Low noise operation
• Supplied with 1.5 m cable
Ordering
AMV 130H, AMV 140H
AMV 130, AMV 140
Type
Supply
voltage
Speed Code No.
AMV 130
24 V~
24 s/mm 082H8036
AMV 140 12 s/mm 082H8038
AMV 130H 24 s/mm 082H8040
AMV 140H 12 s/mm 082H8042
AMV 130
230 V~
24 s/mm 082H8037
AMV 140 12 s/mm 082H8039
AMV 130H 24 s/mm 082H8041
AMV 140H 12 s/mm 082H8043
Technical data
Type AMV 130, AMV 130H AMV 140, AMV 140H
Power supply 24 Vac, 230 Vac; +10 to –15%
Power consumption 1 VA - 24 Vac; 8 VA - 230 Vac
Frequency 50 Hz/60 Hz
Close of force 200 N
Stroke 5.5 mm
Speed 24 s/mm 12 s/mm
Max. medium temperature inside the pipe 130 °C
Ambient temperature 0 … 55 °C
Storage and transport temperature –40 … +70 °C
Protection code IP 42
Weight 0.3 kg
- marking in accordance with standards
EMC- Directive 89/336/EEC, 92/31/EEC, 93/68/EEC,
EN 61000-6-1 and EN 61000-6-3
Low Voltage Directive 73/23/EEC and 93/68/EEC,
EN 60730-2-14
Spare parts
Type
Code No.
Cable (5m) - 24 V
082H8052
Cable (5m) - 230 V
082H8053
2 VD.KG.Y1.02 © Danf oss 06/2006 DH-SMT/SI
Data sheet Actuators for three point control AMV 130, AMV 140, AMV 130H, AMV 140H
Installation Mechanical
The actuator should be mounted with the valve
stem in either horizontal position or pointing
upwards.
The actuator is fixed to the valve body by means
of a mounting ring which requires no tools for
mounting. The ring should be tightened by hand.
Electrical
Important: It is strongly recommended that the
mechanical installation is completed before the
electrical installation.
Each actuator is supplied with the connecting
cable for the controller.
Wiring
AMV 130/140, AMV 130H/140H - 230V
AMV 130/140, AMV 130H/140H - 24V
Commissioning The factory setting of the spindle is the fully
stem up position because of easier mechanical
connection of the actuator on the valve.
Disposal The actuator must be dismantled and the
elements sorted into various material groups
before disposal.
DH-SMT/SI VD.KG.Y1.02 © Danf oss 06/2006 3
Data sheet Actuators for three point control AMV 130, AMV 140, AMV 130H, AMV 140H
1 Check the valve’s neck. The actuator should
be in steam up position (factory setting).
Ensure that the actuator is mounted securely
on the valve body.
2 Energise the actuator according to the wiring
diagram - see page 2.
3 The direction of stem movement can be
observed on the positon indicator.
Installation and
commissioning procedure
(if required)
Manual override
(for service purposes only)
AMV 130, AMV 140
1 Remove the cover.
2 Insert the Allen key 6 into the spindle.
3 Press and hold the button (on the bottom
side of the actuator) during manual override.
4 Pull out the tool.
5 Place cover back on the actuator.
Do not touch anything on
the PCB! Before removing the
cover in need of hand operation
with Allen key power supply
must be disconnected. Lethal
voltage!
Caution:
Do not manually operate the
drive under power!
Remark:
A ”click” sound after energizing the actuator
means that the gear wheel has jumped into
normal position.
AMV 130H, AMV 140H
1 Press and hold the button (on the bottom
side of the actuator) during manual override.
Remark:
A ”click” sound after energizing the actuator
means that the gear wheel has jumped into
normal position.
push
position
indicator
4 VD.KG.Y1.02 © Danf oss 06/2006 DH-SMT/SI
Data sheet Actuators for three point control AMV 130, AMV 140, AMV 130H, AMV 140H
AMV 130(H) / 140(H) +
VZ 3, VZL 3
AMV 130(H) /140(H) +
VZ 4, VZL 4
AMV 130(H) / 140(H) +
VZ 2, VZL 2
AMV 130(H) / 140(H) +
VRBZ 2/3
Dimensions
AMV 130, AMV 140
AMV 130H, AMV 140H
Actuator - valve
combinations
Loading...