Crosley CDB900NW0A, CDB500NW0A, CDB900NS0A, CDB900NB0A, CDB500NB0A Installation Instructions Manual

...

0 (0)

Dishwasher

Installation Instructions

INSTALLER: Leave Installation Instructions with owner. OWNER: Read your dishwasher Use and Care Manual. It contains

important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher.

Printed in U.S.A. 154427301

(04/07)

Read all instructions before installing dishwasher.

For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and

electrical connections, and help you select the best location for the dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door. Failure to follow this warning can result in serious

injury.

Tools and Materials Needed for Installation

Drill, Electric Driver, Socket 3116",V4",5/_6"

Flaring Tool / Tube Cutter (for copper tubing) Flashlight Level Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) Pliers Safety Glasses Saw, Keyhole or V2", 1V2" to 2" Hole Cutters Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred) Tape, Electrical or Duct Tape, Measuring Wire Stripper or Utility Knife Wrench, Hex-end Wrenches, 2 Adjustable (for copper tubing) or 2 Pipe wrenches (for iron pipe plumbing)

Parts You Will Need* (Not#ncluded)

• Drain Hose Clamp, 1W' Diameter

• Elbow, 90°with a 3/d'National Pipe Thread

• Conduit Connector

• Wire Nuts, two (2) for 12-14 gauge wire

If required:

• "Y" Branch Tailpiece and Connector Kit (See Step 4)

• Air Gap Kit (See Step 4)

• Fasteners for floor

anchoring (See Step 9)

Available at: Plumbing Supply Store

Plumbing Supply Store Hardware Store

Electric Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury.

• Examine dishwasher and locate connections. See Step 4.

• Locate dishwasher where there is easy access to drain,

water, and electrical lines. The best location is on either side of the kitchen sink for access to existing plumbing and ease in loading dishes. See Step 4.

• Electrical, water, and drain connections are not the same for

all age, brands, or models of dishwashers. Check the location and length of home utilities. See Step 4.

• A 15-20 amp, grounded, 120 volt AC only, electrical supply is required. See Steps 4 and 8.

• If dishwasher drain hose will be connected to afood disposer for the first time, knock out plug located inside disposer inlet. See Steps 4 and 6.

• Kinked water or drain hoses can cause problems. See Step

• Dishwashers need to be connected to a hot water supply with enough water pressure to insure an adequate fill.

See Steps 4 and 7.

• Each home installation differs. You will need additional parts listed above to complete your installation.

See Steps 4 and 7.

• Flush water line prior to making the final connection to prevent clogging of dishwasher's filter screen. See Step 7.

• The dishwasher will look, sound, and perform best when properly leveled. See Step 5. (NOTE: If levelers are removed during installation, make sure the floor is flat and

free of any obstruction.)

• Anchorthe dishwasher. See Step 9.

1. Remove two (2) screws at front of the kickplate assembly using a #2 Phillips screw driver.

2. Tilt and pull forward to remove. See Figure 1. NOTE: It is not necessary to remove the outer door for installation.

However, you might find it more convenient to do so. You can find directions for removing door in Step 10.

FdcAplateAssembly

AdjustableToeplate (Insulation avdilable somemodols)

Kicl_plate

Water Inlet

Valve

Fl_u/_ I

3. Locate water inlet valve behind kickplate on bottom left underside of unit. The valve has a 3/s" NPT female fitting.

4. Wrap 90 °elbow (not included) with pipe thread tape (or apply joint compound) and thread it into water inlet valve.

5. Tighten elbow with a wrench, leaving elbow pointing toward rear of unit. Toprevent bending of bracket or breaking of valve,

avoid overtightening.

lYf:l 1! ;

Electric Shock Hazard

Observe all local codes and ordinances for electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury.

1. Make sure your location has the right drain, water, and

electrical outlets to make the connections. Do not install unit under a cooktop range, Damage to plastic tub will occur,

-_ f j

, 90°---_ /-- 90 ° __

34,'/_"min.

24 '''_

rain.

Electrical, water,

and drain lines

must be confined

to shaded area.

| 8_

, i_

Flgut_ 2

IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance to open door.

2. Remove any carpet from area to provide motor clearance. Floor

should be flat and free of any obstruction.

IMPORTANT: Drain, water, and electrical lines should be roughed-in before going any further.

Electric Shock Hazard

Electrical, water, and drain lines must be confined to shaded areas in Figure 2. Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock.

NOTE: If dishwasher is installed at end of a cabinet line, sides and back must be fully enclosed.

NOTE: You can order a Cabinet Seal Kit (Kit # 154528701) by contacting your dealer or parts supplier. This kit provides a seal between the unit and cabinets once installation is complete. (This kit is included on select models).

IMPORTANT: Do not cross drain, water, and electrical lines in front of dishwasher motor or frame.

Locating the Connections

1. Review dimensions in Figure 3 tolocate dishwasher's drain, water, and electrical connections.

2. All connections must be made in shaded area in Figure 2.

From rear to

center ofwater

lnlet valve.

F_ure 3

Front

I,_ 23_/s "

l/a-

33/+,,

From #oor to

waterinlet

valve.

Junction Box

(not visible)

RlghtSMe

i_ 49 _/4"

Door in

opon posltion

IMPORTANT: Disconnect power before starting installation.

Electrical

1. The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps.

2. Note the locations of electrical supply and dishwasher's electrical junction box on right underside of unit behind kickplate assembly. See Figure 3.

3. Cut access hole in shaded area shown in Figure 2.

4. Pull electrical cable through hole into installation area.

Water

1. Determine where you will connect to hot water supply. Review Figure 3 and note the location ofwater inlet valve.

Property Damage

Do not use the furnished drain hose or a rubber garden hose for the water supply line. Either of these hoses can burst.

Flooding may occur and cause property damage.

Be sure water inlet valve is )rotected from freezing. If valve freezes and ruptures, flooding may occur.

Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Copper tubing must have a minimum _/8"OD. High-pressure and high-temperature rated plastic tubing with a minimum inner diameter of V4"may be used. A shut-off valve installed outside dishwasher cabinet is best. See Figure 4.

Figure 4

4. Cut water access hole in shaded area in Figure 2.

5. Route water supply line into installation area.

IMPORTANT: Incoming hot water temperature should be at least 120°F (49°C). Water pressure should be between 20-120 psi.

Drain

1. Review Figures 5 and 6 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need.

Figure5

Entry Must be Above

Sink at

2" Drain Hose Hole

If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 5.

Air Gap

3. If you connect to a sink trap, local codes may require you to install an air gap kit, not included. The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 6. An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary).

4. If you connect to a disposer, the large end of drain hose will fit. Figure 7(a). The knock out plug must be removed from

inside disposer inlet before making the final fit to drain hose. See Figure 7(b).

Drain Motor End

F_ure 71a)

•Largerend

/ ofhose

. / _ltsdisposer

Cutfor_/, connection. / Inlet filling.

...... Drain Hose

Cot [or 3./# nconnection.

Drain Air Gap

II r .oekout

_in

Flgnre 71b)

Alternate Drain Through Floor into

_pamte

Trap

Sink at Right

2" Drain Hose Hole

5. Before cutting drain hose access, check both sides of selected

area to avoid interference. Cut a 2" diameter hole in shaded area shown in Figure 2.

6. If the cabinet wall is wood, sand edges of hole until smooth and

rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose.

+ 1 hidden pages