Citroën C1 Dag 2010 Owner's Manual
4
FAMILIARISATION
C. Locking/unlocking the vehicle
from the inside (driver's side).
1. Stop position.
2. Accessories position (1st notch).
3. Running position (2nd notch).
4. Starting position.
A. Locking the vehicle.
B. Unlocking the vehicle.
48
Remote control key Manual central control
STARTING
5
When this bar fl ashes, ac-
companied by an audible
signal, you have around
5 litres of fuel remaining.
1. Interior release lever.
2. Exterior safety catch.
3. Bonnet stay.
68
53
Low fuel level
Remove the key and unscrew the
cap.
After fi lling the fuel tank, screw the
cap back on fully to the right until it
clicks and close the fl ap.
Fuel tank capacity: approximately
35 litres.
After opening the fl ap, insert the key,
turn it slightly to the left then return to
the right. The key returns to its initial
position and the cap is unlocked.
OPEN
Fuel tank Bonnet
6
FAMILIARISATION
Manual air conditioning
This air conditioning system opti-
mises the distribution of the air and
its temperature inside the passenger
compartment.
35
SensoDrive gearbox
This fi ve-speed electronic gearbox
offers a choice between the comfort
of automated operation or the plea-
sure of manual gear changing.
65
Auxiliary socket for portable
equipment
Compatible with many MP3 players,
this socket allows you to listen to
your favourite tracks while travelling.
Refer to the conditions of use in the
"Audio" section.
25
INTERIOR
7
1. Bonnet release
2. Headlamp adjustment
3. Passenger's airbag deactivation
4. Adjustable side air vent
5. Lighting and direction indicator
stalk
6. Driver's front airbag
Horn
7. Dashboard fusebox (under the
instrument panel trim, on the
right and on the left)
8. Rev counter
9. Passenger's door mirror control
10. Passenger's electric window
control
11. Gear lever
12. Cup holder
13. Steering wheel height adjustment
INSTRUMENTS AND CONTROLS
8
FAMILIARISATION
1. Driver's door mirror control
2. Instrument panel
3. Wiper stalk
4. Steering lock and ignition
5. Hazard warning lamps
6. Storage compartments
7. Diffusion grille
8. Windscreen demisting and
defrosting vent
9. Passenger's front airbag
10. Adjustable side air vent
11. Storage box
12. Audio system
13. Ventilation, heating or air
conditioning controls
14. Storage compartments
15. 12 V socket (120 W max)
16. Parking brake
17. Driver's electric window control
INSTRUMENTS AND CONTROLS
9
1. Forwards-backwards adjustment. 2. Seat back angle adjustment. 3. Access to rear seats.
38
Front seats
10
FAMILIARISATION
A. Opening and closing control.
Push or pull control A .
50
B. Door mirrors adjustment control.
When the vehicle is parked, the
mirrors can be folded and unfolded
manually.
37
C. Steering wheel height
adjustment release and locking
control.
1. Control released.
2. Control locked.
37
SITTING COMFORTABLY
Front electric windows Mirrors Steering wheel adjustment
(with power steering)
11
Lighting stalk
Front and rear lamps
Ring A
Lighting off.
Sidelamps.
Dipped/Main beam head-
lamps.
Rear foglamp
Ring B
55
Wiper stalk
Windscreen wipers
MIST Single wipe.
OFF Off.
INT Intermittent wipe.
LO Normal wipe (moderate rain).
HI Rapid wipe (heavy rain).
Rear wiper and rear screenwash
Ring C
56
12
FAMILIARISATION
Temperature
adjustment
Air fl ow
adjustment
Air distribution
adjustment
Rear screen
demisting
34
Air conditioning
Temperature
adjustment
Air recirculation/
Air intake
Air distribution
adjustment
Air conditioning
On/Off
35
Air fl ow adjustment
Rear screen
demisting
Heating
13
I require...
Heating or Manual air conditioning
Air distribution Air fl ow
Air recirculation/
Intake of exterior air
Temperature Manual AC
HOT
COLD
DEMISTING
DEFROSTING
Recommended interior settings
14
FAMILIARISATION
When the ignition is on, the orange
and red warning lamps come on.
When the engine is running, these
warning lamps should go off.
If warning lamps remain on, refer to
the relevant page.
18
A. Rev counter
B. Screen
C. Fuel gauge
17
The dynamic stability control system
(ASR/ESP) optimises the vehicle's
road holding.
For correct operation of the system,
refer to the relevant page.
59
Instrument panel Warning lamps ASR/ESP option
15
Your vehicle has been approved in
accordance with the new ISOFIX
regulation.
The rear seats are fi tted with regula-
tion ISOFIX mountings.
These are three rings for each seat:
- two lower rings A , located
between the vehicle's seat back
and cushion,
- an upper ring B , referred to as
the TOP TETHER, located at
the rear of the seat back at the
bottom.
The ISOFIX child seats are fi tted
with two latches and/or a strap which
are secured easily on these rings,
indicated by labels or a mark on the
rear seat back panel.
44
Passenger's airbag deactivated
63
If the passenger's airbag is
deactivated, this warning lamp
remains on until the passen-
ger's airbag is reactivated.
Driver's seat belt not fastened
warning lamp
1. Insert the key.
2. Select the "OFF" position
3. Remove the key in the OFF
position.
When the ignition is switched
on, the warning lamp fl ashes
until the driver fastens their
seat belt.
Above a speed of approximately
10 mph (15 km/h), the warning lamp
fl ashes accompanied by an audible
signal until the driver fastens their
seat belt.
Passenger's airbag
deactivation
"ISOFIX" mountings
FAMILIARISATION
"SensoDrive" gearbox
Moving off
With the parking brake applied, press
the brake pedal then select position N
to start the engine.
With your foot on the brake, select
position R , E or M .
Release the parking brake, take your
foot off the brake pedal, then accel-
erate.
65
EASY mode (automatic mode)
Select position E using the gear
lever.
The gear engaged is displayed in the
instrument panel screen.
The gearbox continuously selects
the most suitable gear.
66
Manual mode
Place the gear lever in position M ,
then change up or down through the
gears by pressing:
- rearwards, "+" to change up,
- forwards, "-" to change down.
The gear engaged is displayed in the
instrument panel screen.
66
Manual gearbox
Press the clutch pedal fully when
changing gear.
Reverse
To engage reverse gear, push the
gear lever fully to the right then to-
wards the rear.
Reverse gear can only be engaged
when the vehicle is stationary, engine at idle.
16
Approaching the maximum engine
speed, when the rev counter needle
crosses into the red zone, you must
change up.
1. Total/trip distance recorder zero
reset button
2. Warning lamps and indicators
display
3. Direction indicators
4. Speedometer
5. Fuel gauge
MONITORING
6. Total/trip distance recorder
7. Rear foglamp warning lamp
8. Main beam headlamp warning
lamp
9. Dipped beam headlamp warning
lamp
10. "SensoDrive" gearbox gear and
gear lever positions indicator
17
MONITORING
WARNING LAMPS
Warning lamp is on Cause Action/Observations
Release the parking brake to switch off the warning
lamp, keeping your foot on the brake pedal.
Observe the safety recommendations.
For further information on the parking brake, refer
to the "Safety" section.
Parking brake fi xed.
The parking brake is
applied or not properly
released.
STOP
18
Engine oil
pressure
Braking
fi xed, associated
with another
warning lamp.
fi xed, associated
with the STOP
warning lamp.
fi xed.
fi xed, associated
with the ABS
warning lamp.
It is associated with
the engine oil pressure
or the engine coolant
temperature.
The engine oil pressure is
too low.
The braking system
fl uid level has dropped
signifi cantly.
The braking system has
a fault.
Stop as soon as it is safe to do so.
Park, switch off the ignition and call a CITROËN
dealer or qualifi ed workshop.
Stop as soon it is safe to do so.
Park, switch off the ignition and contact a
CITROËN dealer or a qualifi ed workshop.
Top up with brake fl uid recommended by
CITROËN.
If the problem persists, have the system checked
by a CITROËN dealer or a qualifi ed workshop.
Stop as soon as it is safe to do so. Park, switch
off the ignition and contact a CITROËN dealer or
a qualifi ed workshop.
19
MONITORING
Anti-lock
Braking
System (ABS)
fi xed.
The anti-lock braking
system has a fault.
The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a
CITROËN dealer or a qualifi ed workshop without
delay.
Electronic
stability
programme
( ASR / ESP )
fi xed.
The ASR/ESP system
is in action.
The system optimises traction and improves
the directional stability of the vehicle.
fi xed.
The ASR/ESP system
has a fault.
Have it checked by a CITROËN dealer or a
qualifi ed workshop.
Coolant
temperature
fi xed.
The temperature of the
engine coolant is too
high.
Stop as soon as it is safe to do so.
Wait until the engine has cooled down before
checking up the level; top up if necessary.
If the problem persists, contact a CITROËN
dealer or qualifi ed workshop.
Airbags
temporarily.
This lamp comes on for
a few seconds when you
turn on the ignition, then
goes off.
This lamp should go off when the engine is
started.
If it does not go off, contact a CITROËN dealer
or a qualifi ed workshop.
fl ashing.
At least one of the
airbags has a fault.
The airbags may not be deployed in the event of
a serious impact. Have it checked by a CITROËN
dealer or a qualifi ed workshop.
Warning lamp is on Cause Action/Observations
MONITORING
Warning lamp is on Cause Action/Observations
The passenger's airbag
control is set to the OFF
position.
The passenger's front
airbag is deactivated.
In this case you can
install a "rear facing" child
seat.
Set the control to the ON position to activate the
passenger's front airbag. In this case, do not fi t a
child seat in the rear-facing position.
the passenger's
Deactivating
fi xed.
airbag
20
Electric power
Battery
charge
steering
Driver's seat
belt not
fastened
(according to
version)
Emission
control
system
fi xed.
fi xed.
fl ashing, then
above 9 mph
(15 km/h),
accompanied
by an audible
signal.
fi xed.
The battery charging
circuit has a fault (dirty or
loose terminals, slack or
cut alternator belt, ...).
The electric power
steering has a fault.
The driver has not
fastened their seat belt.
The emission control
system has a fault.
The warning lamp should go off when the engine
is started.
If it does not go off, contact a CITROËN dealer
or a qualifi ed workshop.
Drive carefully at reduced speed.
Have it checked by a CITROËN dealer or
qualifi ed workshop.
Pull the strap then insert the tongue in the
buckle.
This lamp should go off when the engine is
started.
If it does not go off, contact a CITROËN dealer
or a qualifi ed workshop without delay.
21
MONITORING
"SensoDrive"
gearbox
fi xed.
The "SensoDrive"
gearbox has a fault.
Contact a CITROËN dealer or a qualifi ed
workshop without delay.
Warning lamp is on Cause Action/Observations
22
MONITORING
TOTAL/TRIP DISTANCE
RECORDER
This indicates the quantity of fuel
available:
- 1/1 and six bars, the fuel tank is full.
- R and one bar fl ashing, the fuel
tank is on the reserve.
Low fuel level
When the minimum level in the fuel
tank is reached, the last bar fl ashes
accompanied by an audible signal.
In certain driving conditions and de-
pending on the engine, the distance
which can be travelled with the fuel
remaining may be less than 30 miles
(50 km).
You have approximately 5 litres
remaining.
When the frequency of the fl ashing
increases, you have approximately
3 litres remaining .
At least 5 litres must be added
after running out of fuel.
When the ignition is switched on,
the distance recorder selected when
the engine was switched off is displayed.
Press button 1 to alternate the dis-
tance display:
- total with "ODO" displayed,
- trip with "TRIP" displayed.
To reset the trip recorder to zero,
when it is displayed, press and hold
button 1 .
22
MONITORING
TOTAL/TRIP DISTANCE
RECORDER
This indicates the quantity of fuel
available:
- 1/1 and six bars, the fuel tank is full.
- R and one bar fl ashing, the fuel
tank is on the reserve.
Low fuel level
When the minimum level in the fuel
tank is reached, the last bar fl ashes
accompanied by an audible signal.
In certain driving conditions and de-
pending on the engine, the distance
which can be travelled with the fuel
remaining may be less than 30 miles
(50 km).
You have approximately 5 litres
remaining.
When the frequency of the fl ashing
increases, you have approximately
3 litres remaining .
At least 5 litres must be added
after running out of fuel.
When the ignition is switched on,
the distance recorder selected when
the engine was switched off is displayed.
Press button 1 to alternate the dis-
tance display:
- total with "ODO" displayed,
- trip with "TRIP" displayed.
To reset the trip recorder to zero,
when it is displayed, press and hold
button 1 .
23
MONITORING
"SENSODRIVE" GEARBOX
INDICATOR
Lever in EASY mode
(automatic mode)
"E" is displayed when this
operating mode is selected.
It goes off on switching to manual
mode.
Lever in manual mode
"M" is displayed when this
operating mode is selected.
It is switched off on switching
to EASY mode.
"Neutral"
"Reverse"
Operating mode:
1st gear
2nd gear
3rd gear
4th gear
5th gear
If this warning lamp comes
on with the engine running,
this indicates a fault with the
" SensoDrive " gearbox.
"!" warning lamp
Contact a CITROËN dealer or a
qualifi ed workshop.
24
AUDIO
Clock adjustment: press for more
than 2 seconds/Access to the
audio settings
On/Off
Volume adjustment
Selection of the source: auxiliary
(or CD or CD changer)
Auxiliary socket for portable
equipment (MP3 player, ...)
Hours adjustment/
Audio settings
Minutes adjustment/
Audio settings
25
AUDIO
On/off
With the ignition key
in the accessories
position or with the
ignition on, press this
button to switch the audio equipment
on or off.
After the engine has been switched
off, the audio equipment can only
operate for approximately 30 minutes, to prevent discharging of
the battery.
Press the upper part
of this button several
times in succession to
increase the volume
of the audio equipment or the lower part
of this button to decrease it.
Volume adjustment
Setting the clock
Press this button several times in succession to gain access
to the bass (BASS) ,
treble (TREB) , front/rear balance
(FAD) and left/right balance (BAL)
settings.
Audio settings
Press this button for
more than 2 seconds,
the clock display
fl ashes:
Auxiliary socket
An auxiliary socket
"AUX" is provided for
the connection of portable equipment (MP3
player, etc.).
When the parameter
is displayed, change
the setting using these
two buttons.
You exit from this mode automatically after a few seconds without any
action.
In order to listen to it,
connect your equipment then press this
button.
The audio equipment controls enable
you to adjust the volume and the audio settings.
To exit from the AUX source, press
AM/FM .
When using an MP3 player: in-
crease the volume of the radio significantly (between 30 and 60) to obtain
a satisfactory playing volume.
- to adjust the hours,
press this button,
- to adjust the minutes,
press this button.
You exit from this mode automatically after a few seconds without any
action.
26
AUDIO
Selection of the AM/FM
(FM1, FM2, FM3) wavebands
Autostore: automatic storing of
6 stations on AM and FM3
TA function on/off:
traffi c information priority
Automatic search for a higher
frequency: double press/
Successive tuning in to
the stations
Selection of the type of radio
programme: News, Sports, Talk,
Pop, Classics
AF function on/off: alternative
frequency
Manual search for a higher
frequency
Selection of the stored station/
Storing of a station: press for
more than 2 seconds
Manual search for a lower
frequency
27
AUDIO
Stereo reception
When the audio equipment receives
a station broadcasting in stereo it automatically transmits stereo sound
and the screen displays "ST" . If the
reception conditions deteriorate, the
audio equipment returns to mono
transmission and "ST" is no longer
displayed.
Press one of these
two buttons briefl y to
increase or decrease
the frequency displayed respectively.
If you maintain the
pressure on the button
in the chosen direction, the frequency will be scanned
continuously.
The scan stops when you release the
button.
Manual station search Automatic station search
Manual station storing
Selection of the radio source
Selection of a waveband
Press this button.
Press this button twice
to select the next station.
Press this button briefl y to listen to
each station available on the FM
waveband for three seconds. To stop
the station scan, press this button
again.
If the traffi c information programme
TA is selected, only stations which
broadcast this type of programme
are selected.
Press the button successively to select
the wavebands FM1,
FM2, FM3 and AM.
Select the required station.
Press one of the buttons "1" to "6"
for more than 2 seconds.
An audible signal confi rms that the
station has been stored.
28
AUDIO
Radio reception
Your audio equipment will
be subjected to phenomena
which do not affect domestic radio
sets. Both MW/LW and FM reception
are subject to various forms of inter-
ference. This is no refl ection on the
quality of the equipment but is due to
the nature of the signals and the way
in which they are transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the result of increasing distance from the
transmitter, defl ection of the signal
by obstacles (mountains, hills, buildings, etc) or of being in an area which
is not covered by a transmitter.
Automatic storing of FM
stations (autostore)
Press this button.
Your audio equipment
automatically stores
the six best transmit-
ters received on AM and FM in your
current location. These stations are
stored on the AM and FM3 wave-
bands. The end of the search is signalled by two audible signals.
Recalling stored stations
On each waveband, a brief press on
one of the buttons "1" to "6" recalls
the corresponding stored station.
If it was not possible to fi nd
six transmitters, the remaining memories remain empty:
three dashes are displayed
on the audio equipment screen for
each empty memory.
29
AUDIO
Regional mode (REG)
Some stations, organised in a network,
broadcast regional programmes in the
various regions which they serve. The
regional mode enables you to continue
listening to the same programme.
Search by type of programme
(PTY)
This enables you to listen to stations which broadcast a type of programme which has a theme (NEWS,
SPORTS, TALK, POP, CLASSICS).
EON system
This system links stations which belong to the same network. It permits
the transmission of traffi c information
broadcast by a station which belongs
to the same network as the station to
which you are listening.
In order to benefi t from this, select the
traffi c information programme TA .
Using the AF (alternative
frequency) function on the FM
waveband
The RDS (Radio Data System) en-
ables you to continue listening to the
same station irrespective of the frequency that it uses in your current
location. The audio equipment continuously searches for the transmitter
which provides the best reception.
Press this button successively to activate
or deactivate the function.
On FM, the multifunction display will
indicate:
- "TP" or "TP EON" : the radio
transmits a programme while
awaiting the broadcasting of traf-
fi c information.
- "TA" or "TA EON" : the pro-
gramme transmitted by the radio
is put on standby while awaiting
the broadcasting of traffi c infor-
mation.
If you wish to interrupt the transmission of a message, press this button
again.
Traffic information
programme (TA)
Press this button successively to activate
or deactivate the function.
The screen will indicate:
- "AF" if the function is activated,
- "AF REG" if the function is acti-
vated at regional level,
- "AF" fl ashing if the function is not
available.
When FM is selected,
press this button:
The volume of the traffi c in-
formation is independent of
the volume of normal radio
listening.
You can adjust it using the
volume button, when the TA pro-
gramme is being transmitted.
The setting will be stored and will be
used during subsequent message
transmissions.
RDS
- "no pty" is displayed,
- then press the button briefl y to
select a programme.
After a few seconds without any action, your selection is stored.
30
AUDIO
CD eject
Selection of the source: CD or CD
changer (or auxiliary)
Selection of the next track
Play the start of each track on
the CD: brief press
: fast forwards play
: fast backwards play
Selection of the previous track
Random play of the tracks on the
CD currently being played
CD changer:
: selection of the previous CD
: selection of the next CD
CD: repeat the current track/CD changer, press for
more than 2 seconds: repeat the current CD
31
AUDIO
Press this button to
select the next track.
CD AND CD CHANGER
Introscan (SCAN)
Press this button to listen to the start of each
track on the current
CD.
Fast play
Press and hold one
of these buttons for
fast forwards or backwards play respectively.
The fast play stops
when the button is released.
When a CD is inserted, printed face uppermost, play begins
automatically.
If there is a CD in the player already,
press this button.
CD FUNCTIONS
Selection of a track on a CD
Press this button to
return to the start of
the current track or
to select the previous
track.
Selection of the CD player
CD eject
Press this button to
eject the CD from the
player.
Random play of the CD
(RAND)
When the CD player
is selected, press this
button.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deactivated when the audio equipment is
switched off.
Repeat of a track on the CD
(RPT)
If you wish to listen
to the current track
again, press this button. To cancel the
repetition, press the
button again.
The use of copied CDs may
cause faults.
Insert circular CDs only.
AUDIO
CD CHANGER FUNCTIONS
Selection of the CD changer
Press this button.
Selection of a CD
Press one of these
buttons on the audio
equipment to select
the previous or next
CD respectively.
Random play of a CD (RAND)
When the CD changer
is selected, press this
button for 2 seconds.
The tracks of the current CD will be
played in a random order.
Press the button again for 2 seconds
to return to normal play.
Repeat of a CD (RPT)
If you wish to listen to
the current CD again,
press and hold this
button.
To cancel the repetition, press the
button again.
The use of copied CDs may
cause faults.
Insert circular CDs only.
32
Loading...