CATEYE
STRADA SLIM
CYCLOCOMPUTER
CC-RD310W
This model comes with a sensor inspired by modern road bikes.
It may not be used for bikes with a large space between the front fork and
spoke.
Before using the computer, please thoroughly read this manual and keep
it for future reference.
Please visit our website, where detailed instructions with movies are
available and the instruction manual can be downloaded.
STRADA SLIM
CC-RD310W
ENG 1
Warning / Caution
•Do not concentrate on the computer while riding. Ride safely!
•Install the magnet, sensor, and bracket securely. Check these periodically.
•If a child swallows a battery, consult a doctor immediately.
•Do not leave the computer in direct sunlight for a long period of time.
•Do not disassemble the computer.
•Do not drop the computer to avoid malfunction or damage.
•When you press the MODE button with the computer installed to the bracket, press around the
dot section on the surface of the computer. Pressing strongly the other section may result in
malfunction or damage.
•When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.
•Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to local regulations.
•LCD screen may be distorted when viewed through polarized sunglass lenses.
Wireless Sensor
The sensor was designed to receive signals within a maximum range of 60 cm, to reduce
chance of interference.
When adjusting the wireless sensor, note the following:
•Signals cannot be received if the distance between the sensor and the computer is too large.
•The receiving distance may be shortened due to low temperature and exhausted batteries.
•Signals can be received only when the back of the computer is facing the sensor.
Interference may occur, resulting in incorrect data, if the computer is:
•Near a TV, PC, radio, motor, or in a car or train.
•Close to a railroad crossing, railway tracks, TV stations and/or radar base.
•Using with other wireless devices, or some particular battery lights.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device
that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate
the equipment.
Hereby, CATEYE Co., Ltd., declares that this CC-RD310W is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Preparing the computer
Perform the All Clear operation, when you use the unit for the fi rst
time or restore the unit to the condition checked at the factory.
Dot section
STRADA SLIM
CC-RD310W
Battery case cover
MENU
AC
MODE
ENG 2
Clear all data (initialization)
1
Press the AC button on the
back of the computer.
AC
Tire circumference
There are the following ways to determine the
tire circumference.
•Measure the tire circumference (L)
Measure the distance when the tire turns right
round with your weight applied, while adjusting
the tire pressure appropriately.
L mm
Select the speed units
2
Select “km/h” or “mph”.
Enter the tire circumference
3
Enter the front wheel tire circumference
of your bicycle in mm.
* Refer to the “Tire circumference refer-
ence table” as a guide.
km/h ↔ mph
MODE
Register the setting
MENU
Increase the value
MODE
Move digits
(Press & hold)
MODE
Register the setting
MENU
•Refer to the tire circumference reference table
* Generally, the tire size or ETRTO is indicated on the side of the tire.
ETRTO Tire size
47-203 12x1.75 935
54-203 12x1.95 940
40-254 14x1.50 1020
47-254 14x1.75 1055
40-305 16x1.50 1185
47-305 16x1.75 1195
54-305 16x2.00 1245
28-349 16x1-1/8 1290
37-349 16x1-3/8 1300
17x1-1/4(369)
32-369
40-355 18x1.50 1340
47-355 18x1.75 1350
32-406 20x1.25 1450
35-406 20x1.35 1460
40-406 20x1.50 1490
47-406 20x1.75 1515
L (mm)
1340
ETRTO Tire size
50-406 20x1.95 1565
28-451 20x1-1/8 1545
37-451 20x1-3/8 1615
37-501 22x1-3/8 1770
40-501 22x1-1/2 1785
47-507 24x1.75 1890
50-507 24x2.00 1925
54-507 24x2.125 1965
25-520 24x1(520) 1753
24x3/4 Tubular
28-540 24x1-1/8 1795
32-540 24x1-1/4 1905
25-559 26x1(559) 1913
32-559 26x1.25 1950
37-559 26x1.40 2005
40-559 26x1.50 2010
L (mm)
1785
ETRTO Tire size
47-559 26x1.75 2023
50-559 26x1.95 2050
54-559 26x2.10 2068
57-559 26x2.125 2070
58-559 26x2.35 2083
75-559 26x3.00 2170
28-590 26x1-1/8 1970
37-590 26x1-3/8 2068
37-584 26x1-1/2 2100
650C Tubular
26x7/8
20-571 650x20C 1938
23-571 650x23C 1944
650x25C
25-571
26x1(571)
40-590 650x38A 2125
L (mm)
1920
1952
Set the clock
4
Pressing and holding the MODE button
switches the display to “Displayed time”,
“Hour”, and “Minute” in order.
12h ↔ 24h or increases
the value
MODE
Display format Switching “Hour” and “Minute”
(Press & hold)
MODE
Register the setting
(Finish)
MENU
ETRTO Tire size
40-584 650x38B 2105
25-630 27x1(630) 2145
28-630 27x1-1/8 2155
32-630 27x1-1/4 2161
37-630 27x1-3/8 2169
40-584 27.5x1.50 2079
50-584 27.5x1.95 2090
54-584 27.5x2.1 2148
57-584 27.5x2.25 2182
18-622 700x18C 2070
19-622 700x19C 2080
20-622 700x20C 2086
23-622 700x23C 2096
25-622 700x25C 2105
28-622 700x28C 2136
30-622 700x30C 2146
L (mm)
Display format
MinuteHour
ETRTO Tire size
32-622 700x32C 2155
700C Tubular 2130
35-622 700x35C 2168
38-622 700x38C 2180
40-622 700x40C 2200
42-622 700x42C 2224
44-622 700x44C 2235
45-622 700x45C 2242
47-622 700x47C 2268
54-622 29x2.1 2288
56-622 29x2.2 2298
60-622 29x2.3 2326
L (mm)
How to install the unit on your bicycle
Refer to the Quick Start Manual, where you can learn how to
install the unit in detail using a movie.
http://www.cateye.com/products/detail/CC-RD310W/manual/
Bracket Bracket rubber pad
STRADA SLIM
(SPD-02)
Speed sensor
CC-RD310W
ENG 3
Sensor
rubber pad
1-1
or
2 3
1-2
Rubber band
(large band for bracket)
(middle and small bands for sensor)
Nylon tie
Attach the bracket to the stem or handlebar
1-1
When mounting the bracket to the stem
Bracket
Bracket
rubber pad
1-2
When mounting the bracket to the handlebar
Rubber band
(x 3)
Magnet
Nylon tie
* Use a nylon tie togeth-
er to fi x it fi rmly.
Bracket
Bracket
rubber pad
Nylon tie
or
Rubber band
2
1
How to install the unit on your bicycle
Install the sensor and magnet in a position where
the following conditions are satisfi ed.
STRADA SLIM
CC-RD310W
ENG 4
The distance from the computer
to the sensor is within the transmission data length, and the back
of the computer faces downward.
Max.
60 cm
(23-5/8” )
The magnet passes through the sensor
zone of the speed sensor.
Speed sensor
(SPD-02)
Magnet
SENSOR ZONE
The clearance between the sensor surface and the magnet is within 5 mm.
Speed sensor
(SPD-02)
5 mm
(3/16”)
Check the mounting position of the sensor and magnet
Spoke
Get an estimate of the mounting position where the clearance
between the magnet surface and
sensor zone is 5 mm or less, by
sliding up and down the sensor
and magnet before mounting.
2
Install the sensor
Nylon tie
or
Sensor rubSpeed sensor
(SPD-02)
3 4
Install the magnet Remove/Install the computer
Magnet
To the SENSOR ZONE
Spoke
ber pad
Positioning and testing
Adjust the sensor magnet so that the conditions of , , are satisfi ed, and
then check the operation by turning the front wheel slowly.
Rubber band
Inside the
front fork
Click
While supporting it by hand,
Push it out as if lifting the front up
Inside the front fork
Operating the computer [Measuring screen]
Pace arrow
Indicates whether the current speed is faster (
slower (
speed.
) than the average
) or
STRADA SLIM
CC-RD310W
ENG 5
Switching computer function
Pressing the MODE button switches the selected data at the bottom in the order shown in the
following fi gure.
Sensor signal icon
Flashes in synch with a sensor signal.
Tire icon
Selected mode
MODE operation when the computer
is mounted on the bracket
MODE
Current speed
0.0 (4.0) – 105.9 km/h
[0.0 (3.0) – 65.9 mph]
Speed unit
Tm
Elapsed Time
0:00’00” – 9:59’59”
MODE
Clock
0:00 - 23:59 or
1:00 - 12:59
MODE
Odo
Total Distance
0.0 – 9999.9 /
10000 - 99999 km[mile]
MODE MODE
Dst
Trip Distance
0.00 – 999.99 km [mile]
MODE
Mx
Maximum Speed
0.0(4.0) – 105.9 km/h
[0.0(3.0) – 65.0 mph]
MODE
Dst2
Trip Distance-2
0.00 – 999.99 /
1000.0 - 9999.9 km [mile]
MODE
Av
Average Speed
0.0 – 105.9 km/h
[0.0 – 65.0 mph]
When the computer is mounted on the bracket,
once you press the dot section on the unit, the
MODE button is pressed.
Pressing MENU on the measurement screen
changes to the menu screen. Various set-
MENU
tings can be changed on the menu screen.
To “Changing the computer settings [Menu screen]” (page 7)
* The average speed displays .E in-
stead of the measurement value,
when Tm exceeds about 27 hours
or Dst exceeds 999.99 km. Reset
the data.
Operating the computer [Measuring screen]
STRADA SLIM
CC-RD310W
ENG 6
Starting / Stopping measurement
The unit automatically measures according to the movement
of your bicycle.
The speed unit (km/h or mph) fl ashes during measurement.
Starting
measurement
Stopping
measurement
Resetting data
With the data other than Dst2 displayed, pressing and holding
the MODE button returns the measurement data to 0.
With Dst2 displayed, pressing and holding the MODE button
returns only Dst2 to 0.
The total distance (Odo) cannot be reset.
MODE
(Press & hold)
Power-saving function
If the computer has not received a signal for 10 minutes,
power-saving screen will activate and only the clock will be
displayed.
When you press MODE, or the computer receives a sensor
signal, the measuring screen reappears.
Power-saving screen
10 minutes
1 hour
Sleep
MODE
If another 60 minutes of inactivity elapses in the powersaving screen, only the speed unit is displayed on the screen.
With such a screen, pressing the MODE button returns to the
measurement screen.
Changing the computer settings [Menu screen]
MODE
STRADA SLIM
CC-RD310W
ENG 7
MENU
Pressing MENU on the measure-
Measuring
screen
ment screen changes to the menu
screen.
Various settings can be changed
on the menu screen.
From “Selecting the measurement unit”
Switching the circumference A/B
The tire to be used ( ) can be selected.
Changing the
settings
MENU
Changing the
settings
MODE
(Press & hold)
Register the
setting
MENU
With a menu you want to
change displayed, once
you press and hold the
MODE button, you can
change various setting by
the button operation as
described.
* After changing, be sure to
register the setting(s) by
pressing the MENU button.
* Leaving the menu screen
without any operation for
1 minutes returns to the
measurement screen, and
changes are not saved.
MODE MODE
Overview of the menu screen
MODE
Switching the
circumference A/B
MODE
Selecting the
measurement unit
Setting the tire
circumference
Entering the total
Setting the tire circumference
Set the tire circumference.
Changing the
settings
distance
MODE
Setting the
clock
MODE
MODE
Setting the
function
To “Setting the clock”
↔ Switch
MODE MODE
(Press & hold) (Press & hold)
Register the
setting
MENU MENU
MODE
Register the
setting
Move digits
MODE
(Press & hold)
Increase
the value
MODE
Changing the computer settings [Menu screen]
From “Setting the tire circumference” To “Entering the total distance”
STRADA SLIM
CC-RD310W
ENG 8
Setting the clock
Set the clock.
Changing the
settings
MODE
(Press & hold)
Register the
setting
MENU
Selecting the display
12h ↔ 24h
MODE
MODE
(Press & hold)
Hour
Increase
the value
MODE
MODE
(Press & hold)
Minute
Increase
the value
MODE
Setting the function
MODE MODE
MODE
(Press & hold)
You can skip the selected data to be displayed.
Once you select “Off” for a particular selected
data, it will be skipped in the measurement screen.
Changing the
settings
MODE
(Press & hold)
Register the
setting
MENU
MODE
* The elapsed time (Tm) cannot be skipped.
* Even the hidden selected mode is measured,
and the measurement result will be refl ected
when it is displayed again.
Dst
Dst 2
Av
Mx
MODE
(Press & hold)
Odo
ON ↔ OFF
Selected
data switch
Changing the computer settings [Menu screen]
From “Setting the function” To “Switching the circumference A/B”
STRADA SLIM
CC-RD310W
ENG 9
Entering the total distance
Enter the total distance.
(No decimal number can be entered.)
* Once you enter any value to the total distance, you can start from
the value you entered. Use this function when you renew your unit
and/or replace the battery.
Changing the
settings
MODE
(Press & hold)
Register the
setting
MENU
Move digits
MODE
(Press & hold)
Increase
the value
MODE
Selecting the measurement unit
MODE MODE
The speed unit (km/h or mph) can be selected.
Changing the
settings
MODE
(Press & hold)
Register the
setting
MENU
km/h ↔ mph
MODE
In use
Maintenance
To clean the computer or accessories, use diluted neutral
detergent on a soft cloth, and wipe it off with a dry cloth.
Replacing the battery
Computer
When the display becomes dim, replace the battery. Install a
new lithium battery (CR1616) with the (+) side faced upward.
Waterproof inner cap
Press
* Press the top edge of waterproof
inner cap to remove it.
* After replacing the computer bat-
tery, follow the procedure described
in “Preparing the computer”
* Noting the total distance before replacing the battery allows
you to start from the total distance you enter manually after
replacing it.
Speed sensor
When the speed is not displayed even after adjusting
correctly, replace the battery.
Insert new lithium batteries
(CR2032) with the (+) sign
upward, and close the battery
cover fi rmly.
* After replacement, check the
positions of the sensor and
magnet.
Slide
Open
COIN
CR1616
OK
NO!
Close
CR2032
Troubleshooting
The sensor signal icon does not fl ash.
(the speed is not displayed)
Check that the clearance between the sensor and magnet
is not too large. (Clearance: within 5 mm)
Check that the magnet passes through the sensor zone
correctly.
Adjust the positions of the magnet and sensor.
Is the computer installed at the correct angle?
Back of computer must face toward the sensor.
Check that the distance between the computer and sensor is correct. (Distance: within 20 to 60 cm)
Install the sensor within the specifi ed range.
Is the computer or sensor battery weak ?
* In winter, battery performance diminishes.
If the computer reacts only when it is close to the sensor,
weak batteries may cause it.
Replace with new batteries according to the procedure
specifi ed in the section “Replacing the battery”.
Nothing is displayed by pressing the button.
Replace the computer battery according to the procedure specifi ed in the section “Replacing the battery”.
Incorrect data appear.
Clear all according to the procedure described in “Preparing the computer”.
All measured data are deleted.
STRADA SLIM
Standard accessories
1603890
Parts kit
1603893
Rubber band / nylon tie
1699691N
Wheel magnet
1603850
Lithium battery
CR1616
Optional accessories
1602196
Speed sensor
(SPD-01)
CC-RD310W
1603891
Speed sensor
(SPD-02)
1603892
Bracket kit
1604100
Out-front bracket
ENG 10
1665150
Lithium battery
CR2032
1602194
Bracket kit
(FlexTight™)
1600280N
Bracket band
(FlexTight™)
1602193
Bracket
(for FlexTight™)
In use
CO
., LTD.
STRADA SLIM
CC-RD310W
ENG 11
Specification
Lithium battery (CR1616) x 1
Approx. 1 year
Computer
Battery
Battery life
Speed
sensor
* This is the average figure of being used under 20 °C tem-
perature and the distance between the computer and the
sensor is 60 cm.
* The factory-loaded battery life might be shorter than the
above-mentioned specification.
Controller
Display Liquid crystal display
Sensor No contact magnetic sensor
Transmission
distance
Tire circum-
ference range
Working tem-
perature
Dimensions/
weight
* The specifications and design are subject to change without
notice.
4 bit, 1-chip microcomputer
(Crystal controlled oscillator)
Between 20 and 60 cm
0100 mm - 3999 mm
(Initial value: A = 2096 mm, B = 2096 mm)
0 °F - 104 °F (0 °C - 40 °C)
(This product will not display appropriately
when exceeding the Working Temperature
range. Slow response or black LCD at lower
or higher temperature may happen respectively.)
Computer
Speed
sensor
(If the computer is used for 1 hour/
day; the battery life will vary depending on the conditions of use.)
Lithium battery (CR2032) x 1
Distance reaches about
10000 km (6250 mile)
1-55/64” x 1-17/64” x 1/2”
(47 x 32 x 12.5 mm) /
0.43 oz (12 g)
2-43/64” x 1-3/16” x 21/64”
(67.7 x 30 x 8.1 mm) /
0.48 oz (13.5 g)
Limited warranty
2-Years Computer/Sensor only
(Accessories and Battery Consumption excluded)
CatEye cycle computers are warranted to be free of defects
from materials and workmanship for a period of two years
from original purchase. If the product fails to work due to
normal use, CatEye will repair or replace the defect at no
charge. Service must be performed by CatEye or an authorized retailer. To return the product, pack it carefully and
enclose the warranty certificate (proof of purchase) with
instruction for repair. Please write or type your name and
address clearly on the warranty certificate. Insurance, handling and transportation charges to CatEye shall be borne by
person desiring service. For UK and REPUBLIC OF IRELAND
consumers, please return to the place of purchase. This does
not affect your statutory rights.
Please register your CatEye product on the website.
http://www.cateye.com/en/support/regist/
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn: CATEYE Customer Service Section
Phone : (06)6719-6863
Fax : (06)6719-6033
E-mail : support@cateye.co.jp
URL : http://www.cateye.com
[For US Customers]
CATEYE AMERICA, INC.
2825 Wilderness Place Suite 1200, Boulder CO 80301-5494 USA
Phone : 303.443.4595
Toll Free : 800.5.CATEYE
Fax : 303.473.0006
E-mail : service@cateye.com
Loading...