CatEye CC-CL200N User Manual

E

INSTRUCTION MANUAL

Fig.1

Fig.2

Reset

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

lever

slide

Fig.10

magnet

Fig.11

sensor band A

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

sensor

sensor band B

rubber pad

sensor band B

rubber pad

sensor band A

parallel

sensor

spacer

In case of
aerofork

Attachment for aerofork

fixing nut

L

A

B

A

AT

B

AT

bracket

rubber pad

To remove

push

pull

front

front fork

screw

front fork

long screw

spoke

magnet

A. Main Display (Speed)
B. Wheel Circumference Mark
C. Mode Symbol
D. Mode Button
E. Wheel Sensor Pulse Symbol
F. Speed Scale Symbol

G. Auto Mode Symbol

OPERATION FEATURES

Two buttons are provided on the top of the main unit and two on the bottom.
These buttons are used as follows:

•Mode Button (top left button)

Whenever this button is pressed, the mode display changes in the order
shown in fig.1, and the data is displayed on the sub-display. Note: If this
button is kept pressed for more than 2 seconds,

•Start/Stop Button (top right button)

Measurement of trip distance, elapsed time and average speed is started or
stopped when the start/stop button is pressed. Whenever this button is
pressed, start and stop are repeated. During measurement the speed scale
symbol blinks.
Note: This button does not function if the auto mode function is set to ON
[Refer to the explanation of the Auto (Automatic Start/Stop) Function below].

•Set Button (bottom left button)

• To set the wheel circumference:
Stop the measurement in the (O) mode, then press the SET button.

• To set the 24-hour clock time:
Stop the measurement in ( ) mode, then press the SET button.

• To set auto mode to ON or OFF:
Select the (T),(A) or (D) mode, then press the SET button.

•AC (All Clear) Button (bottom right button)

When this button is pressed, all the data stored in memory is cleared.

After all displays illuminate, the "mile/h" symbol illuminates. This button should
be pressed only after replacing the battery or when irregular display of infor­mation occurs due to static electricity,etc. Once this button is pressed and all
memory is erased, it will be necessary to set the wheel circumference, time,
etc. again. (refer to Main Unit Preparation)

Reset Operation: (Fig.2)

Press left button to select any mode except total distance (O) and press left
and right buttons together. Stored data of trip distance (D), elapsed time (T),
average speed (A) and maximum speed (M) are all reset to zero. (In the total
distance display mode, the current wheel circumference (A) or (B) is shown.)

MAIN UNIT PREPARATION

User must make the following setting according to instructions before
the cyclocomputer can be used properly.

1. How to measure the exact Wheel Circumference (L)(Fig.3)

First, adjust tire pressure and then put a mark on the tire tread and the ground
simultaneously. Then ride the bike one full wheel revolution. Mark the ground
at the end of one revolution and then measure the distance between the two
marks. This measure is your actual wheel circumference. Or, the "Setting Val­ues Cross Reference Table" can help you to find out an approximate wheel
circumference according to tire size.

2. Setting the Speed Scale (Fig.4)

When the AC button is pressed and all displays illuminate then the "mile/h"
appears as shown in fig.4. "km/h" and "mile/h" are displayed alternatively each
time the right button is pressed. Select any speed scale as desired and press
SET button to complete the setting.

3. Setting the Wheel Circumference (Fig.5.6)

This cyclocomputer is able to memorize two different wheel circumferences.
One main unit can be used on two bicycles subject to buy another set of
bracket and sensor.
Two wheel circumferences, (A) 2155mm and (B) 2030mm, have been set be­fore the cyclocomputer left our factory. The (A) wheel circumference 2155mm
(standard for 27 inch tire) will blink as shown in fig.5. If you want to enter
2155mm and 2030mm, simply press the SET button. If you want to change,
press either the right button to increase or left button to decrease the number.
To change the number rapidly keep the button pressed. Once you reach the
setting you want, press the SET button. If you want to set a second circumfer­ence, press the left and right buttons together before pressing the SET button.
The wheel circumference 2030mm is displayed and blinks(fig.6). Set to a de­sired wheel circumference in the same manner as the first circumference set­ting and press SET button to complete the setting.

4. Selecting one of the two Wheel Circumference (Fig.7)

Set the Auto Mode to ON. (Refer to the explanation of Auto Mode function.)
While keeping the right button pressed , press the SET button. The first wheel
circumference measurement will be displayed for a few seconds, then the sec­ond setting will appear.

5. How to reset the Wheel Circumference

Select the (O) mode and stop the measurement. Press SET button and the
already set wheel circumference will blink on the sub-display. Refer to '3.Set­ting the wheel circumference' to complete the setting.

Setting the 24-hour Clock (Fig.8)

Press left button for more than 2 seconds to select the 24-hour clock display.
Stop the measurement by pressing the right button. Press SET button and the
minute display will start to blink. Press right button to select a minute time
ahead of the current time by 1 to 2 minutes. Next press left button and the hour
will blink. Press right button to set to current hour time. Press SET button to
complete the setting.

MOUNTING TO BIKE

Attach the bracket near handlebar stem, using rubber pad (fig. 9). Cut and
adjust the length of the rubber pad if necessary.

• Slide the main unit onto the bracket from front until it clicks into position. To
remove the main unit, pull it forward while depressing the lever on bracket
(fig.10).

How to Mount the Sensor on the Right Front Fork Leg.(fig.11)

Mount the sensor in the highest possible position on the right front fork leg.
Adjust the position, clearance and direction as follows:
(1) Insert the band B into the slit of the band A, and put the rubber pad inside

of the band A (fig. 12). Adjust the length of the bands in order that the
screw-fastening part of the bands is parallel when mounted to the fork (fig.

13). * To pull out the band B from band A, tug strongly.

(2) Mount the adjusted bands to fork along with the sensor, by temporarily

tightening the screw (fig. 14).If the space between front fork and spoke of
your bike is big, use the spacer and long screw as in the fig.15, so that the
clearance between sensor and magnet will be approx. 5mm.

(3) Attach the magnet securely to the right side of the spoke (fig. 16) so that

the magnet properly faces the sensor zone (fig. 17).

(4) A 5mm clearance shall be kept between the sensor and magnet(fig.18).

Then align the magnet with sensor zone (fig.16). Meanwhile, the sensor
shall aim at the main unit indicated by the triangle marked on the sensor.
Then tighten the screw to secure the sensor in position. Cut the excess
sensor band B with scissors or the like.

Check points for sensor mounting:

1.Keep a 5 mm clearance between the sensor and magnet.

2.The magnet surface shall align to the sensor zone.

3.The triangle mark on the sensor shall aim at the main unit.

display appears.

H. Sub-Display

(Selected function)

I. Start/Stop Button

J. Battery Case Cover

K. Set Button

L. AC Button

triangle mark

sensor zone

Fig.17

less than

5mm

magnet

spoke

Fig.18

Fig.19

Fig.20

Fig.21

sensor

CLOSE

OPEN

CLOSE

OPEN

magnet

S
E
N

S
O

R
Z
O
N

E

sensor zone

CR2032

CR2032

contact

1. Bracket

2. Sensor(Transmitter)

3. Sensor Band A

4. Sensor Band B

5. Magnet

6. Rubber Pad

TEST

Mount the main unit on the bracket. If current speed doesn't appear on the
main display, press either left or right button to release the unit from the power
saving mode. Then spin the front wheel to make sure the wheel sensor pulse
symbol flickers. If it does not flicker, adjust the position of sensor until it flickers
normally. The mounting is completed and the cyclocomputer is operational.

THE CORDLESS SYSTEM

The sensor picks up wheel revolution signal and transmits the signal to the
receiver in the main unit. The main unit receives, calculates and displays the
data. The approximate service hour of batteries is as follows:

The main unit (receiver):--- Approx. 2 years (average 1 hour's use per day)

The sensor (transmitter): -------Total distance of approx. 10,000 miles (16,000 km)
Note: To prevent external signal interference, the sensor signal reception
range is restricted. For best performance, the triangle mark on the sensor shall
aim at the direction to the main unit. The distance between the sensor and
main unit must be kept within 70 cm. The signal reception range may shorten
as a result of low ambient temperature or lowered battery power. It is advisable
to replace the sensor battery before it fails. The battery service hours quoted
above is the average for a 65 cm distance between the sensor and main unit.

• The cordless system may be interfered with in the following situation, so that

main unit may display false data.

1. Riding near railroad crossings and trains.

2. Riding in places where intensive electromagnetic wave or field exist,
such as TV transmission station and radar installations.

3. When two bicycles carrying similar cyclocomputers are ridden side by
side.

REPLACING THE BATTERIES

Batteries are already loaded in the main unit and the sensor.

How to replace battery in Main Unit (Fig.20)

Open the battery cover on the back and insert a new CR2032 (lithium) with the
(+) pole upward, while pressing the side of the battery against the contact.
Press AC button to erase all stored data and then redo the settings.

How to replace battery in Sensor (Fig.21)

Take off the sensor from the bicycle. Open the battery cover on the back and
insert a new CR2032 (lithium) with the (+) pole upward, while pressing the side
of the battery against the contact. Mount the sensor back to the bicycle and
adjust to relative position, clearance and direction.

7. Screw

8. Long Screw

9. Spacer

10.Attachment for aerofork

11.Nylon Tie

DISPLAY FUNCTIONS

S Current Speed 0.0(3.0) to 65.9 miles/hr ±0.3mile/h

This is always displayed on the main display and updated once a second.

A

D

O Total Distance 0.0 to 99,999 miles ±0.1mile

This is continuously measured until battery wears down or all clear operation is

A

O

D

T

A

M

POWER SAVING FUNCTION

done. At 100,000 miles(km), it returns to zero and counting begins anew.

D Trip Distance 0.00 to 999.99 miles 0.01mile

The trip distance from start to current point is displayed. With Reset operation, it

A

returns to zero.

T Elapsed Time 0:00'00" to 9:59'59" ±0.003%

Elapsed time is measured from start to current point, in units of hours, minutes and

A

seconds. At 10 hours, it returns to zero and counting begins anew. With Reset
operation, it returns to zero.

A Average Speed 0.0 to 65.9 miles/hr ±0.3mile/h

A

The average speed from start to current point is displayed within 27 hours 46 min­utes 39 seconds (99,999 seconds) or 999.99 miles (km). If either is exceeded, (.E)
is displayed and calculation ceases.

M Maximum Speed 0.0 (3.0) to 65.9 miles/hr ±0.3mile/h

A

With Reset operation, it returns to zero and counting begins anew.

24 hr. Clock Time 0:00´ to 23:59´ ±0.003%

The current time is displayed by a 24-hour clock.

A

When the main unit is left without receiving any signal for one hour, the power will
be turned off automatically. Resulting in SLEEP state in which only the 24-hour

A

clock displays. The main unit can not receive any signal in this state. Press left or
right button to restore signal reception.
Note: Remember to restore signal reception before every journey.

AUTO (AUTOMATIC START/STOP) FUNCTION

The Cordless 2 is equipped with a selective auto function allowing automatic start
or stop of measurement without using the right button.

A

AT

T

MAINTENANCE/PRECAUTIONS

• Do not leave the main unit exposed to direct sunlight when the unit is not in use. Do not disassemble
the main unit.

• Don't pay too much attention to your computer's functions while riding! Keep your eyes on the road
and give due consideration to traffic safety.

• Check the relative position of magnet and sensor periodically.

• For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply paint
thinner, benzine, or alcohol, which may damage on the surface.

How to Set On/Off the Auto Function

Select (T), (D) or (A) to sub-display and then press SET button. The AT symbol
will display when auto function is set ON. Repeat to set OFF the auto function.
Note: In SLEEP state, auto start will not function. Press left or right button to restore
signal reception first. (Refer to Power Saving Function)

TROUBLE SHOOTING

No display. ------------------------------------------------------ Replace the main unit battery with new one.
Incorrect data appears. -------------------------------------- Execute "All Clear" operation.
Figures do not appear on the main display ------------- Cancel the power saving function.
Current speed does not appear.--------------------------- Check the sensor position and direction.
Speed is not displayed when riding with high speed or at low temperature.

--------------------------------------------------------------------- Check the sensor position and direction.

--------------------------------------------------------------------- Has the battery worn out?

Even when the right button is pressed, the cyclocomputer does not operate.

--------------------------------------------------------------------- Set the auto mode to OFF.

The entire liquid crystal screen is dark and unusual display is seen where it should not be.

--------------------------------------------------------------------- It returns to normal state if left in the shade.

Display response is slow. ----------------------------------- It returns to normal state when temperature rises.

SPECIFICATIONS

Applicable Cycle Sizes 10 mm - 2,999 mm(Initial value: A:2155 mm B:2030 mm)
Power Supply Main unit: ------------------------------------Lithium Battery (CR2032)x1/approx. 2years

Dimension / Weight 2"x 1-13/10"x 29/32" / 1.2 oz (29 g)
* The specifications and design are subject to change without notice.

Sensor with transmitter: ------------------ Lithium Battery (CR2032)x1/approx. 1,000miles

CO

.,LTD.

CO

.,LTD.

CO

.,LTD.

CO

.,LTD.

CYCLOCOMPUTER
Model CC-CL200N

®

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to
this device that are not expressly approved by Cat Eye Co., Ltd. may void the user’s
authority to operate the equipment.

US. PAT. NO.4633216, 4636769, 4642606, 5236759 and Patent Pending

Copyright© Aug. 2001 CAT EYE Co., Ltd.

Setting Values Cross Reference Table

Table de Correspondance des Valeurs de Réglage

Wertetabelle zur Einstellung des Radumfanges (die Radgröße entnehmen Sie der Aufschrift des Reifens)

Tabel voor het bepalen van de wielomtrek (de bandenmaat staat vermeld aan beide zijden van de band)

Tabella delle Corrispondenze dei Valori di Regolazione (La dimensione del pneumatico figura su ogni lato del pneumatico)

Tabla de Valores

TIRE SIZE L(mm)
dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

24 x 1 1753
24 x 3/4 Tubular 1785
24 x 1-1/8 Tubular 1795
24 x 1-1/4 1905
24 x 1.75 1890
24 x 2.00 1925
24 x 2.125 1965
26 x 1(559mm) 1913
26 x 1(650c) 1952
26 x 1.25 1953
26 x 1-1/8 Tubular 1970
26 x 1-3/8 2068
26 x 1-1/2 2100
26 x 1.40 2005

#169-6690N

Parts Kit

Kit d'accessoires

Ersatzteil

Onderdelen set

Kit d'accessori

Kit de piezas

(El tamaño de la rueda está marcado al lado de la llanta)

TIRE SIZE L(mm)
dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

26 x 1.50 1985

26 x 1.75 2030

26 x 1.95 2050
26 x 2.00 2055
26 x 2.1 2068
26 x 2.125 2070
26 x 2.35 2083
27 x 1 2145

27 x 1-1/8 2155

27 x 1-1/4 2161
27 x 1-3/8 2169
650 x 35A 2090
650 x 38A 2125
650 x 38B 2105

(The tire size is marked on both sides of the tire.)

(La dimension du pneu figure de chaque côté du pneu)

TIRE SIZE L(mm)
dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

700 x 18C 2070
700 x 19C 2090
700 x 20C 2086
700 x 23C 2096
700 x 25C 2105
700 x 28C 2136
700 x 30C 2170

700 x 32C 2155

700C Tubular 2130
700 x 35C 2168
700 x 38C 2180
700 x 44C 2224

#169-6660N

Bracket Kit

Kit support d'unite principale

Halterung

Bracketkit

Kit supporto

Soporte

#169-6670N

Cordless Sensor

Palpeur (Emetteur)

Sensor mit Sender

Sensor-draadloos

Sensore"Senzafilo"

Sensor sin cable

#169-9780 #169-6680

Attachment for aerofork Universal Sensor Band

Fixation pour fourche AERO Collier Universel de Détecteur

Zusatz zur Federgabel Universalsensorband

Bevestiging voor aerovork Universele Sensorband

Attacco per forcella aerodinamica Fascetta Universale di sensore

Sujección para horquilla aerodinámica Banda universal del sensor

#169-6667

Center Mount Bracket Kit

Kit de montage central del l´unité principale

Halterung für Montage en der Lenkermitte

Stuurbocht Bevestinging Set

Kit di Montaggio al Centro del manubrio

Kit Soporte para Montaje Central

#169-6669

Stem Mount Bracket Kit

Kit de montage de l´unité principale sur la broche du guidon

Halterung für Montage en der Lenkerstange

Stuurpen Bevestiging Set

Kit di Montaggio sull´ attacco manubrio

Kit Soporte para Montaje en Tija

#169-9691 #166-5150

Wheel Magnet Lithium Battery (CR2032)

Aimant pour roue Pile au lithium (CR2032)

Radmagnet Lithium-Batterie (CR2032)

Wielmagneet Lithium Batterij (CR2032)

Magnete ruota Batteria al Litio (CR2032)

Iman de la rueda Bateria de Litio (CR2032)

Design Patented

CCMCL2-010402

1

Specifications/Caracteristiques techniques/Technische daten/ Specificaties/
Caratteristiche tecniche/

Controller/

Affichage

Display/
Sensor/

Détecteur

Cordless Système/
Operating Temperature Range/

LIMITED WARRANTY

2-Year Warranty: Only Main Unit/Sensor

If trouble occurs during normal use, the part is repaired or replaced free of charge. The service must be
performed by CAT EYE Co., Ltd.. and the product needs service must be returned to CAT EYE Co., Ltd.
directly by purchaser. When returning the product for CAT EYE warranty service, pack it very carefully,
and enclose the warranty certificate and instructions for repair. Please make sure to write or type your
name and address clearly on the warranty certificate, so that the product can be shipped back to you as
soon as the necessary repair/adjustment is completed. Insurance, handling and transportation charges
to our service shall be borne by person desiring service.

Address for service

GARANTIE LIMITEE

Garantie de 2 ans : Unité Principale / Détecteur uniquement

En cas de problème en cours d'utilisation normale, le produit sera réparé ou remplacé gratuitement. Les réparations doivent être
effectuées par CAT EYE Co., Ltd. et le produit à réparer doit être retourné à CAT EYE Co., Ltd. directement par l'acheteur. Tout
produit retourné au service de réparation CAT EYE doit être soigneusement emballé et le certificat de garantie ainsi que les
instructions de réparation doivent accompagner le produit à réparer. Il est conseillé à l'acheteur d'écrire lisiblement ou de dacty­lographier ses nom et adresse sur le certificat de garantie, afin que le produit puisse lui être directement retourné dès que les
réparations/réglages nécessaires sont terminés. Le coût de l'assurance ainsi que les frais de manutention et de transport vers le
service de réparation CAT EYE sont à charge de la personne souhaitant une réparation sous garantie.

Adresse d'envoi pour réparation

BEGRENZTE GARANTIE

2-Jahres-Garantie: Auf den Computer und den Sensor

Falls während des normalen Gebrauchs Fehler auftreten, wird das entsprechende Teil kostenlos re­pariert oder ersetzt. Die Reparatur muß von CAT EYE Co., Ltd. durchgeführt werden, und das zu
reparierende Produkt muß direkt durch den Händler an CAT EYE Co., Ltd. gesandt werden. Bei der
Rückgabe des Gerätes zur Reparatur packen Sie es sorgfältig anbei. Achten Sie darauf, Ihren Namen
und Ihre Anschrift klar und deutlich lesbar auf die Garantiekarte zu schreiben, damit das Gerät so
schnell wie möglich nach Beendigung der notwendigen Reparatur/Einstellung an Sie zurückgesandt
werden kann.

Anschrift bei Garantieansprüchen

z. H.: CAT EYE Kundendienstabteilung oder wenden Sie sich bitte an den entsprechenden Importeur.

GARANTIEBEPALINGEN

Garantie: 2 jaar op computer en sensor

Mochten er problemen optreden gedurende normaal gebruik, dan geschiedt reparatie of vervanging kosteloos.
Dit dient door de fabrikant Cateye Co., Ltd. uitgevoerd te worden. De computer moet door de importeur aan
Cateye Co., Ltd. teruggezonden worden. Bij terugzending van de computer moet deze zorgvuldig verpakt worden
en dient het garantiebewijs, de aankoopbon en een beschrijving van het probleem meegezonden te worden. Ver­meldt duidelijk uw naam en adres in blokletter of met de schrijfmachine op het garantiebewijs, zodat de computer
in goede orde terruggestuurd kan worden.Verzekerings-, verzend- en transportkosten zijn voor rekening van de
koper.

Adres:

LIMITAZIONE DELLA GARANZIA

Garanzia di due anni

Questo prodotto CATEYE è garantito con la riserva di una utilizzazione corretta, contro ogni difetto di
fabbrica e di materiale. Le riparazioni effettuate nel quadro della presente garanzia sono gratuite a
condizione che siano rispettate le seguenti disposizioni. Il costo dell'assicurazione come le spese di
stoccaggio e di trasposrto sono a carico di chi richiede la riparazione. Questa garanzia è limitata alla
riparazione dell'unità principale esclusi il filo, il supporto e qualsiasi accessorio. Si prega il compratore di
scrivere chiaramente il proprio Cognome Nome ed indirizzo sul Certificato di garanzia completandolo in
tutte le sue parti (Rivenditore/Data di acquisto etc.).

Indirizzo per la rispedizione per riparazione

GARANTÍA LIMITADA.

2 Años de Garantía: Sólo Unidad Principal/Sensor.

Si sucedieran problemas durante un uso normal, la pieza será reparada o reemplazada gratuitamente. El servicio debe
ser realizado por CATEYE CO., LTD. y el producto que necesite del servicio debe ser devuelto a CATEYE directamente
por el comprador. Cuando se envíe el producto al servicio de garantía de CATEYE se ha de empaquetar muy cuidado­samente y adjuntar el certificado de garantía e instrucciones para la reparación. Por favor, asegúrese de escribir clara­mente su nombre y dirección en el certificado de garantía, con objeto de que el producto le sea devuelto a Vd. tan pronto
como la reparación o ajuste necesario haya sido efectuado. Los gastos del seguro, manejo y transporte hasta nuestro
servicio serán a cargo de la persona demandante de servicio.

Para reparación enviar a:

Calculateur

/Anzeige/Display/Visualizzazione/

/Sensor/Sensor/Rivelatore/

System sans fil

Especificaciones

/Controler/Controleur/Elaboratore/

-------------------------------------- 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)

------------------------------------------------------------------------------------ Liquid Crystal Display

--------------------------------------------------------------------------- No Contakt Magnetic Sensor

---------------------------------------------------------------- Directional electromagnetic induction

Température d’utilisation

-------------------------------------------------------------------------------- 0°C - 40°C(32°F - 104°F)

Sensor

/Kabelloses System/Draadloze systeem/Sistema sin hilos/

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Contador

Pantalla

/zulässige Betriebstemperatur/Toegestane temp./Temperatura di utilizzo

Service & Research Address for United States Consumers:

Attn.: CAT EYE Customer Service Section

CAT EYE Service & Research Center

Phone: [phone] Toll Free: 800-5CATEYE

Fax: [phone] e-mail: [e-mail]

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japon.

1705 14th St. 115 Boulder, CO 80302

Attn : CAT EYE Customer Service Section.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Zogauw als de reparatie/vervanging geschiedt is, wordt de computer aan u geretourneerd.

2-8-25, Kuwazu, Higashi-Sumiyoshi-ku, Osaka 546-0041, Giappone.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Ter attentie van: Cateye klantenservice

Att.: Dipartamento Assistenza Clienti

TEL.: [phone] FAX: [phone]

Attn.: CAT EYE Customer Service Section

Sistema cordless

CO

CO

.,LTD.

.,LTD.