Cateye CC-CD200N User Manual

!

L(mm)

12 x1.75 935
14 x 1.50 1020
14 x 1.75 1055
16 x 1.50 1185
16 x 1.75 1195
18 x 1.50 1340
18 x 1.75 1350
20 x 1.75 1515
20 x 1-3/8 1615
22 x 1-3/8 1770
22 x 1-1/2 1785
24 x 1 1753
24 x 3/4 Tubular

1785
24 x 1-1/8 1795
24 x 1-1/4 1905
24 x 1.75 1890
24 x 2.00 1925
24 x 2.125 1965
26 x 7/8 1920
26 x 1(59) 1913
26 x 1(65) 1952
26 x 1.25 1953
26 x 1-1/8 1970
26 x 1-3/8 2068
26 x 1-1/2 2100
26 x 1.40 2005

26 x 1.50 2010

26 x 1.75 2023

26 x 1.95 2050

26 x 2.00 2055
26 x 2.10 2068
26 x 2.125 2070
26 x 2.35 2083
26 x 3.00 2170
27 x 1 2155
27 x 1-1/8 2161
27 x 1-1/4 2161
27 x 1-3/8 2169
650 x 35A 2090
650 x 38A 2125
650 x 38B 2105
700 x 18C 2070

700 x 19C 2080

700 x 20C 2086

700 x 23C 2096

700 x 25C 2105
700 x 28C 2136
700 x 30C 2170
700 x 32C 2155
700C Tubular 2130
700 x 35C 2168
700 x 38C 2180
700 x 40C 2200

L mm

SET

START/STOP

MODE

®

CAT EYE ASTRALE 8

CYCLOCOMPUTER CC-CD200N

E: Owner’s Manual

ASTRALE8

U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending

Please read these instructions carefully before installing or
using the CAT EYE ASTRALE 8.

Please keep this manual in a safe place for future reference.

Installation of the Computer on Your Bike

The computer comes with the following parts:

3

5

7

The smooth edge of the zip
tie should be on the outside

Center

7

4

9

Inward Side of
The Crank Arm

1

1 Bracket
2 Cord
3 Speed Sensor

4 Cadence Sensor

1

Rear wheel

2

2

9

8

5 Sensor Rubber Pad
6 Wheel Magnet

(Long Cord)

(Short Cord)

7 Cadence Magnet
8 Bracket Rubber Pad
9 Nylon Ties (10)

Mount the wheel magnet and speed sensor

•Mount the wheel magnet 6 on a spoke of the rear wheel so the surface of the
magnet faces the sensor.

•

Mount the speed sensor 3 (long cord) on the left chainstay with nylon ties 9.

Note

The nylon ties can only be used once, please install with care.

6

spoke

Important Note

Mount the magnets 6 and the sensors 3 in the appropriate positions so that the
center of each
and crank arm are rotated. The magnet should be no more than 5mm from the sensor.

Sensor Side

magnet 6 aligns with the marked sensor line when the rear wheel

3

Sensor Side

6

7

Marked Line

Mount the cadence magnet and cadence sensor.

• Mount the cadence magnet 7 on the left crank arm so that it faces the sensor.

• Secure the cadence sensor 4 (short cord) on the left chain stay with nylon ties 9.

Important Note

When the crank is spinning, the center of the magnet 7 should pass in front of the sensor

marking line. The distance between the sensor and the magnet 7 should be within

4
5mm. After adjusting the magnet and sensor, secure tightly with nylon ties.

4

6

9

Left Chain Stay

Marked Line

Center

Left chainstay

Rear wheel spoke

Within 5 mm

4

Adjust

Copyright © 2002/2003 CAT EYE Co. Ltd.

CCMCD2N-030531 066600252 1

3

2

1

9

3

Left chainstay

6

3

Adjust

9

3

Left Chain Stay

7

Crank Arm

Within 5 mm

•Pay attention to the road or trail! Do not be distracted by the
computer.

• Be sure to securely mount the magnet, the sensor, and the

Warning

bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws have not come loose.

• Keep batteries out of reach of small children. Dispose of batter­ies according to local regulations.

• Avoid unnecessary prolonged exposure to the sun.

• Never attempt to disassemble the computer head.

Important

• Don’t use thinner, benzene or alcohol to wipe the surface of the

Note

Mount The Bracket

3

Secure the cord by fastening it to the frame with zip ties at regular intervals.
Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the
screw. Slide the computer into the bracket until you hear the click sound. When you need to
remove the computer, press the lever on the handlebar bracket and slide the computer
forward.

Basic Functions Test

4

Spin the rear wheel to see if Speed is reading properly. Push the mode button until Cadence
(Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading properly.
When you receive a signal, tightly secure the sensor so it does not move.

Computer Set-up

(For first use or after replacing the battery)

START/STOP Button

MODE Button

All Clear

1

Push the AC button on the backside.
* Push the AC button when using this

Measurement Selection

2

Select the measurement unit, kilometer or mile, by pushing the
MODE button. Fix it by pushing the SET button.

computer. They may damage the surface of computer.

Note

Allow enough wire clearance in the area marked with to insure you can turn

the handlebars all the way from side to side without pulling the wire.

1

8

Note

When the computer does not indicate the speed/cadence, check the position of the

magnet and the sensor.

Rotate the rear wheel.

SET Button

system for the first time and every
time the battery is replaced.

Kilometer

SET

MODE

Mile

AC Button

Rotate the crank arm

Contact Point

Refer to the chart below for
approximate tire lengths.

AC Button

Lever

9

You need to know
your tire size or the
roll out length of your
tire in MM's.

Tire size

Slide

1

OKOK

Set The Tire Circumference

Set the tire circumference in mm.

3

Note

Refer to the chart shown on the right.

Setting is fixed and completed by pushing the SET button.

Increase the
number
Max. 2999 mm

Decrease
the number
Min. 10 mm

(the screen will show the time measurement in this state)

* The auto mode is ON in this state.

Preparation Complete.

Tire size is usually shown on
the sidewall of tires.

Power-Saving Screen

(When no signal is received for about 1 hr. the
screen switches to the power-saving mode)

When you push either of the MODE
button or the START/STOP button
or you ride the bicycle, the display
comes back to the measurement
display.

START/STOP

MODE

SET

SET

Speed

0.0 (4.0) - 300.0 km/h
[0.0 (3.0) - 185 mph]
or

Cadence

0.0 (20.0) - 299.9 rpm

You can program the tire size.

Return to the Elapsed Time

Range of set: 10 - 2999 mm

Increase
the number

Decrease
the number

Display for Measurements

Mode Selection Illustrations (bottom of the screen)

Cdc

Cadence

0(20) - 299 rpm

or

Speed

0.0 (4.0) - 300.0 km/h

Av

Average Speed

0.0 - 300 km/h [0.0 - 185.0 mph]

Odo

Odometer

0.0 - 99999 km [mile]

Mx

Maximum speed

0.0 (4.0) - 300.0 km/h
[0.0 (3.0) - 180.5 mph]

Dst

Trip Distance

0.00 - 999.99 km[mile]

Tm

Elapsed Time

0:00’00” - 9:59’59”

Return to Clock display

When the measurements
are stopped.

When the measurements
are stopped

Clock

0:00 - 23:59
[1:00 - 12:59]

While any measurement is
displayed on the screen

Return to Elapsed
Time display

For 2 sec.

MODE

MODE

START/STOP

MODE

MODE

Increase the number

SET

SET

Set the hour Set the minute

Setting The Clock Time

24 hour or 12 hour system is to be used with km/h or mph
unit respectively.

Auto-mode Icon

When lit, the measurements
starts or stops
automatically.

If Elapsed Time exceeds 27 hours or Trip
Distance exceeds 999.99km, Average
Speed shows E. and ceases calculation.

Computer Operations

Selection of the data-display mode (bottom of the screen)

Press the Mode button to navigate to each of the sub-displays listed on the right.
Press and hold the mode button for two seconds in any mode to display the Clock Time.

Start or Stop of Measurements

The computer can be programmed to run in either MANUAL
MODE or AUTO TIME MODE. In Manual Mode you must press
the START / STOP button to turn on and off the Timer, which
records Distance and Average Speeds. In Auto Time the com­puter turns the Timer on and off depending on a signal from the
sensor.

When you push the button, Elapsed Time, Average Speed and
Trip Distance are recorded, and stopped with the second push
of the button.

• Auto Time Mode (Automatic Measurement)

When the icon
done. This is called auto-mode in which the rotation of the wheel
is detected to make the measurements start or stop automati­cally. (When the icon
surements by pushing the START/STOP button)

is lit, the measurements are automatically

is lit, you cannot start or stop the mea-

• Manual Measurements

When you don’t see the icon
stop the measurements by pushing the START/STOP button.

When you push the button, Elapsed Time, Average Speed and
Trip Distance are started, and stopped with the second push of
the button.

on the screen, you can start or

• How to set ON or OFF the Auto-Mode

Push the SET button while Elapsed Time (Tm) Trip Distance
(Dst) or Average Speed (Av) is displayed, then the icon
“lit” (ON) or turned OFF.

Resetting Elapsed Time, Trip Distance, Average and Max.
Speed

Push the MODE button and the START/STOP button at the same
time while the measurements other than Odometer, Elapsed
time, Maximum Speed, Average Speed and Trip Distance are
zeroed. The Odometer cannot be reset.

Measurement

START/STOP

SET

is

While Elapsed Time,
Trip Distance or Aver­age Speed is displayed

MODE

Unit Icon

Tm
Dst
Av

Computer Functions

• Power-Saving Function

When no signal has been received for about 1 hr, the computer switches to power­saving mode and only displays the Clock. When any button is pushed or the bicycle
is riden, the measurement mode comes back.

• Selection of The Data-display Mode

In Auto-Mode you can choose between Speed or Cadence to be displayed in the top
screen.

Speed is initially selected in the upper dis­play. When the computer is in
press the START/STOP button. Cadence
will now appear in the upper display. Speed
will be in the lower display. Switch it back
with the same procedure.

Troubleshooting

mode,

Speed Cadence

No display appears.

Is the battery dead?
Replace it and do all clear procedure.

Strange data appears

Do all clear procedure.
Data of odometer is also erased.

Measurements do not start when the START/STOP button is pushed.

Is the icon
Turn the Auto-Mode off to enable the start or stop of the measurements by manual opera­tion of the button.

ON?

AT

START/STOP

No speed or cadence data can be measured.
(If the speed or cadence data is not displayed, have the contact

points short-circuited a few times by a metal plate. In the case
that this short-circuiting is detected by the computer, the com­puter is considered normal and the bracket and the sensor possi­bly have the cause of trouble.)

Is the gap between the sensor and the magnet too big?
(should be within 5 mm)
Does the marked line of the sensor align with the center of
the magnet?
Adjust the position of the magnet and the sensor.
Wipe the contact points of the bracket or computer clean.
Is the cord broken? Even if the outside of the cord looks normal, there could be damage.
Replace the bracket and sensor set with a new one.

Additional troubleshooting at www.cateye.com

Maintenance

• To clean the computer or the attached parts, use diluted neutral
detergent on a soft cloth and wipe it off with a dry cloth.

Replacing The Battery

When the display becomes dim, replace the battery.

• Put a lithium battery CR2032 in the computer with the (+) mark
facing up.

• After replacing the battery, refer to "Computer Set-Up" and do an
all clear operation.

START/STOP

The contacts to be short-cir­cuited intermittently are located
on the back.

Speed Cadence

Close

Open

Specifications

Battery/Its Life : ----------------------------- A Lithium Battery (CR2032), Approx:3 yrs.

Control System : ---------------------------- 4-bit 1-chip micro-computer (with a crystal oscillator)
Display : -------------------------------------- Liquid crystal display
Sensing System : --------------------------- No-contact magnetic sensor
Range of tire circumference setting : ----- 10 mm - 2999 mm (Initial value 2096 mm)
Range of Operational Temperature : ------ 0°C - 40°C (32°F - 104°F)
Dimension and Weight(Computer) : ------ 38 x 54 x 17.5 mm [1-1/2 x 2-1/8 x 11/16"] / 28 g [1.0 oz]
* The factory-loaded battery life might be shorter than the above-mentioned specification.
* The specifications and design are subject to change without notice.

(Approx:1 hr per day usage.)

Limited Warranty

-Year Warranty : Computer Head Only

2

If any trouble or damage occurs during normal use, the product computer will be repaired or replaced
free of charge. Type your name, address, telephone number or e-mail address, date of purchase and
the situation of trouble and send it back together with the product to the closest address below. Trans­portation charges shall be borne by the customer. After being repaired, the product will be shipped
back to the customer.

* Accessory parts are available for the customers as shown below.

#169-9400N

Bracket Sensor Kit (Rear wheel sensor)

(Bracket sensor and batteries are not covered under the warranty)

CO

., LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn.: CAT EYE Customer Service Section

Service & Research Address for North American Consumers:
CAT EYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302
Phone: [phone] Toll Free: 800-5CATEYE
Fax: [phone] e-mail: [e-mail]

#169-9757N

Attachment Kit

#169-9765

Cadence Magnet

URL: http://www.cateye.com

#169-9691N

Wheel Magnet

#166-5150

Lithium Battery (CR2032)

Standard Parts

#169-9402N

Center Mount Bracket Kit (Rear wheel sensor)

Optional Parts

#169-9404N

Stem Mount
Bracket Kit
(Rear wheel sensor)

#169-9403N

Bracket Sensor Kit for Aero Bar
(Rear wheel sensor)

#169-9760

Magnet for Composit Wheel