Carnes VWDK User Manual

COPYRIGHT CARNES CO.© 1998
ALL RIGHTS RESERVED

SUPERSEDES 22302

22302-A

CARNES COMPANY, 448 S.Main St., P. O. Box 930040, Verona, WI.53593-0040 Phone: [phone] Fax:[phone] [e-mail] http://www.carnes.com

MODEL VWDK — DIRECT DRIVE

W ALL VENTILAT ORS

SPECIFICATION SHEET

STANDARD FEATURES

• Spun and shaped aluminum housing • Non-overloading, backwardly inclined wheel

• Integral motor overload protection on all standard single phase motors • Isolated motor wheel-drive assembly

• Disconnect switch on all motors except explosion proof • Spark resistant construction

• Ventilated motor compartment with motor out of airstream • Mounting frame

NOTE: Drawing is to locate dimensions. Refer to catalog for actual model configuration

STANDARD MATERIAL AND THICKNESS IN INCHES (Millimeters)

Motor Cover Approx.

Outer Curb Diffuser Wt. Less
Unit Lid Tube Shroud Cap Std. (Galvanized Motor
Size (Alum.) (Alum.) (Alum.) (Alum.) Wheel Steel) Lbs. (Kg.)

06 .063 (1.6) .040 (1.0) .080 (2.0) .050 (1.3) Aluminum 22 ga. (.8) 45 (20)
08 .063 (1.6) .040 (1.0) .080 (2.0) .050 (1.3) Aluminum 22 ga. (.8) 45 (20)
10 .063 (1.6) .040 (1.0) .080 (2.0) .063 (1.6) Aluminum 22 ga. (.8) 50 (23)
12 .063 (1.6) .040 (1.0) .080 (2.0) .063 (1.6) Aluminum 22 ga. (.8) 50 (23)
15 .063 (1.6) .040 (1.0) .080 (2.0) .063 (1.6) Aluminum 20 ga. (.9) 75 (34)
18 .063 (1.6) .040 (1.0) .080 (2.0) .063 (1.6) Aluminum 18 ga. (1.2) 95 (43)

STANDARD DIMENSIONS IN INCHES (Millimeters)

Unit Depth Wall Mounting Frame Wall Conduit

Unit B Mounting 1-1/2 (38) x 1-1/2 (38) Angle Opening Location
Unit Dia. Standard Extended Cap OD Sq. Damper
Size A B B C Sq. D E F Size G H

06 25-5/8 (651) 23-1/4 (591) 23-1/4 (591) 15-1/2 (394) 15-3/8 (391) 6-15/16 (176) 4-11/16 (119) 12 (305) 12 (305) 3-3/4 (95) 5 (127)
08 25-3/4 (654) 24-5/8 (625) 24-5/8 (625) 15-1/2 (394) 15-3/8 (391) 6-15/16 (176) 4-11/16 (119) 12 (305) 12 (305) 3-3/4 (95) 5 (127)
10 27-5/8 (702) 25-1/4 (641) 25-1/4 (641) 17-5/8 (448) 17-1/2 (445) 8 (203) 5-3/4 (146) 14 (355) 14 (355) 5-3/8 (136) 5-3/8 (136)
12 27-3/4 (705) 26-7/8 (683) 26-7/8 (683) 17-5/8 (448) 17-1/2 (445) 8 (203) 5-3/4 (146) 14 (355) 14 (355) 5-3/8 (136) 5-3/8 (136)
15 32-3/4 (832) 29-7/8 (759) 34-5/8 (880) 20-1/2 (521) 20-3/8 (518) 9-7/16 (240) 7-3/16 (183) 17 (432) 17 (432) 6-7/8 (175) 5-7/8 (150)
18 38-3/4 (984) 31-1/8 (791) 35-7/8 (911) 25 (635) 24-7/8 (632) 11-11/16 (297) 7-7/16 (189) 22 (559) 22 (559) 9-5/16 (237) 7-11/16 (195)

IP [English] Units

SI (Metric) Units