Canon T 60 User Manual

Canon
Tso
INSTRUCTIONS
Precautions
1) This camera is not resistant to water, and cannot be used underwater or outdoors if raining or snowing. If ac cidentally dropped in water, contact an authorized Canon service facility as quickly as possible. Remove water
droplets from the camera with a clean dry cloth. If exposed to salt spray, clean it thoroughly afterward with a clean, damp, well-rung cloth.
2) Store the camera in a cool, dry, dust­free place. Be sure to keep the camera out of direct sunlight, and away from “hot spots" such as the trunk or rear window shelf of a car. Avoid places where moth balls are
used, and in excessive humidity, use a desiccant.
3) Do not attempt to disassemble the camera yourself. Always take it to an authorized Canon service facility for
repair.
[J ]
4) Use a blower brush to remove dust and sand from the lens and inside the camera. Do not apply any fluids to the lens or body. Take it to a Canon service facility for more cleaning if necessary.
5) Film passing through x-ray examina tions at airports may be exposed and ruined even when loaded in the camera. Request a hand-checked in spection to avoid damage.
6) Color reproduction may be adverse ly affected if film is left in the camera for a long time. Always develop ex posed film promptly.
See p. 40 for camera care.
Introduction
The Canon T60, a single-lens reflex (SLR) camera designed for first-time users, places an emphasis on providing basic SLR functions. It is equipped with simple controls and functions in a lightweight, compact body. The viewfinder provides all necessary camera setting and ex posure information. The T60 features “Aperture-priority AE’’ mode providing uncomplicated automat
ic exposure operation for beginning
users, and “Manual” mode allowing full control of the camera to give the more ex perienced user free reign in exploring
creative ideas.
Lastly, the T60 employs an FD mount which accepts lenses from Canon’s large
FD lens line-up used by professionals worldwide.
T60 Features
1. Aperture-priority AE and Manuai ex posure modes
2. FD mount accepts FD ienses
3. Lightweight, compact body for ease of handling
Please read these instructions carefully for a thorough understanding before tak
ing pictures.
Whiie reading this booklet, unfold the front and back flaps for easy reference to the camera’s parts.
NOMENCLATURE
Selector Dial
A; Automatic
L: Lock
1000-1; Shutter speeds (manual)
B: Bulb (long exposure)
Film Advance Lever Shutter Button
Frame Counter
Strap Fixture Grip
Self-timer Button
(Red Lamp) Aperture Ring
Selector Dial Mark
Accessory Shoe
Rewind Crank/Knob
Film Speed Dial
Aperture Scale
Zooming Ring
Focusing Ring
Viewfinder
Eyepiece
Film Guide Rail
Rewind Shaft
Film Chamber
Lens Release Button
Sprocket
Film Take-up Spool
Pressure Plate
Film Window
Battery Compartment
42
Attaching the Neckst rap
1) Attach the neckstrap rings to the strap fixtures on the camera.
43
2) As shown in the illustration, attach the ends of the neckstrap to the neck­strap rings so that they come to the
inside of the neckstrap.
Table of Contents
Preparations
1. Loading the Batteries 6
2. Lens Attachment............................ 7
3. Checking the Batteries................... 8
4. Viewfinder information
5. Hoiding the Camera
6. Focusing and Shutter Button Action
7. Setting the Fiim Speed 15
8. Loading the Film
Taking Pictures
1. Automatic Exposure Operation 20
2. Removing the Film
3. Manual Exposure Operation 24
4. Self-timer Function . . 28
5. Bulb (Long Exposure) Shooting . 29
6. Using Infrared Film 31
7. Flash Photography . . 32
................................
....................
.....................
..........................
.......................
11
12
16
23
9
Appendix
1. Understanding Depth of Field . . .34
2. Film Plane Indicator
......................
36
Interchangeable Lenses
Accessories
1. Cases
.........
38
........................
37
2. Dioptric Adjustment Lenses . . . . 39
Camera Care...........................................40
Specifications ........................................40
Attaching the Neckstrap .......................43
Preparations
1. Loading the Batteries
This camera uses two LR44 alkaline bat teries or two SR44 silver batteries.
1) Remove the battery holder by turning it counterclockwise with a coin or similar object.
2) As shown on the diagram on the out side of the battery holder, insert two batteries into the holder with the © side of each battery facing up.
3) Replace the battery holder and turn it clockwise using a coin or similar ob
ject to secure it in place.
When changing the batteries, be sure to replace both batteries with new ones of the same brand.
Remove the batteries if the camera is not to be used for an extended peri od of time.
2,
Lens Attachment
1) Remove the rear lens cap and body cap by turning counterclockwise.
2) Align the red dots on the lens and the camera, and then turn the lens clock
wise until it stops and locks in place.
• To remove the lens, hold the lens release button down and turn the lens counterclockwise,
3) Remove the lens cap.
3.
Checking
1) Set the selector dial to “A”.
2) Rotate the winding lever until it stops.
3) While looking through the viewfinder, press the shutter button halfway.
• If at least two of the red LEDs in
side the viewfinder are lit or blink ing, the batteries are okay.
• If none of the LEDs light up, either
the batteries were inserted upside down or the batteries are exhaust ed and need to be replaced.
fhe Baffer/es
• Battery life is approximately 1 year
under normal use.
When the camera Is not being used,
be sure to set the selector dial to "L” (Lock) to prevent unnecessary bat tery drain.
4.
Viewfinder information
Split-image Rangefinder
Microprism Rangefinder
Matte Screen
The LEDs in the viewfinder iight up or
blink when necessary to infornn you of various exposure information. The infor mation provided in the viewfinder is shown in the illustration at the left.
■ : These LEDs light or blink to in dicate camera settings and con ditions.
AUTO; This LED lights when the selec
tor dial is set to A (automatic ex
posure).
M: This LED lights when the selec
tor dial is set to a manual ex
posure position (any position other than “A” or “L").
OVER: This LED lights to warn of over
exposure.
1000-1: The LED corresponding to the
set shutter speed lights. All shutter speeds are actually the reciprocal of the numerals displayed. For example, “125” Indicates a shutter speed of 1/125 sec.
60V: This Is the fastest shutter speed
that can be used with a flash. Flash Is synchronized at all shutter speeds 1/60 sec or slower.
LT: This LED lights when a Long
Time shutter speed of 2-8 se conds is set.
10
B: This LED lights when the
camera is set to Bulb mode. When the selector dial is set to
“B” (Bulb), the shutter will re main open for as long as the shutter button is held pressed.
5.
Holding the Camera
If the camera moves while a picture is be ing taken, the resulting picture may be un clear. Sharp pictures require that the camera be held very still when the shut ter button is pressed. Try the following camera-holding technique to avoid disap pointments.
1) Grasp the camera grip securely with the right hand.
2) Use your left hand to support both the camera body and the lens, and keep your left elbow close to your body.
#
3) Lightly hold the camera against your nose and look into the viewfinder,
4) With your feet spread slightly apart, place one foot in front of the other to stabilize your stance.
■ There is no absolute camera holding technique which is right for every in
dividual. Practice holding the camera in different ways to determine which is the best technique for you. Prac ticing in front of a mirror is helpful.
11
6.
Focusing and Shutter Button Action
By rotating the lens’ focusing ring, you can focus on objects located in any part of the viewfinder image area.
1) Set the selector dial to “A”.
12
2) While looking through the viewfinder, rotate the lens’ focusing ring until the viewfinder image appears sharp.
Loading...
+ 59 hidden pages