Canon DR-5010C User Manual

Document Scanner DR-5010C

1.

Log on to Windows with an account that has
administrator privileges.

2.

Insert the DR-5010C Setup Disc into the
computer’s CD-ROM drive.

The setup wizard automatically starts up when
you insert the CD-ROM into the CD-ROM
drive. If the setup wizard does not start up, run
the setup.exe application on the CD-ROM.

For Windows Vista

When using Windows Vista, the “User Account
Control” screen may appear. In this case, log
on as an administrator and click [OK].

3.

Click [Typical Installation].

[Typical Installation] installs all of the software.
If you want to select which parts of the
software to install, click [Custom Installation].

4.

Click [Install].

All of the currently displayed software is
installed. To install only selected software,
click [Back] and select [Custom Installation].

5.

Click [Next].

6.

Read the software license agreement, and
click [Yes] if you consent to its conditions.

Installation of the scanner driver starts.

7.

Click [Finish] to complete the installation.

Next, the installation wizard for CapturePerfect

3.0 appears.

8.

Click [Next].

9.

Read the software license agreement, and
click [Yes] if you consent to its conditions.

10.

Check the destination folder for the installation,
and click [Next].

Installation of CapturePerfect 3.0 starts.

11.

Click [Finish] to complete the installation of
CapturePerfect 3.0.

Note

W
arr

anty C

ard

(
U
.S

.A an
d

Cana

d
a on

ly)

Regis

tr
at
i

o
n
C

ar
d

(U
.S

.A
a
n

d Ca
n

ad
a

only)

A
d
o

b
e
A

c
ro
b

at

S
e
t
u

p
D

is
c

U
s
e

r
’
s
G

u
i
d
e

E
a

s
y S
t
a

r
t
G

u
i
d
e

(
Th

i
s
M
an

u
al)

D
R

­5010

C
S
c
ann

e
r

P
o
w

e
r Co

rd

U
S
B

Ca
b
l
e

D
R

­5
0
1

0
C

S
e
tu
p

D
i
s
c

T

h
e
D
R

-5010
C

S
e
t
up

D
is
c
is

i
n
s
e

r
t
e
d
i
n t

h
e

U
se

r
'
s
G
u

i
d
e
.

D
o
c
u
m

e
n
t

E
j
e
c
t
G

u
i
d
e

Q

u
i
c
k

Re
f

e
r
e
n

c
e
G

u
i
d
e

C
A
N
O
N

C
A
N
A
D

A

IN
C

.

6
3

9

0
D
I
XI

E
R
D

M
IS
S
I
S
S
AU

GA

O
N
L
5
T

9

Z

9

0
8
8
0
2
8
1
0

9
9

­L
5
T
1
P
7

­B
R
0
1

D
o
c
u
m
e
n
t S
c
an
n
e
r

1.

Peel off all the orange tape from the outer casing.

2.

Carefully open the document feed tray.

Document
Feed Tray

3.

Peel off the orange tape from all the places marked ▼ below.

4.

Grab the edge of the upper unit as shown, and carefully open it until it stops.

Upper Unit

Pickup Roller

The protrusion in the middle of the upper unit holds the pickup roller. Do not
grab this protrusion when opening the upper unit, because it may damage the
pickup roller or cause feed errors.

5.

Remove the protective sheet and the packing materials securing the pickup
roller.

Pickup Roller

6.

Remove the roller cover, take out the packing materials securing the retard
roller, and then reinstall the roller cover.

Roller Cover

Retard Roller

7.

Gently close the upper unit. Make sure it is closed securely by pushing on both
edges until you hear a click.

Warning

Warning

Easy Start Guide

Thank you for purchasing the Canon DR-5010C Document Scanner.
This Easy Start Guide describes the procedure for setting up the scanner for use. Follow the
procedures outlined in this Easy Start Guide to set up the scanner. Details on using the
scanner are described in the User’s Guide packaged with the scanner. Before you start using
the scanner, make sure to thoroughly read the User’s Guide.

Checking the Package Contents

When you unpack your scanner, make sure all of the following accessories are included.
If any of the items listed below are missing or damaged, contact your local authorized Canon
dealer or service representative.

DR-5010C Scanner

Power Cord

USB Cable

Doc

u

Tha

m

nk

T

e

h

Easy Start Guide

y

is

o

n

pr

E

u

a

o

f

t Sca

o

s

ce

y

sc

r p

d

St

ann

urc

u

a

r

th

es

r
t

h

e

e

G

a

ou

r

sc

sin

u

ar

i

nn

t

an

d

e

li

g

e

n

d

ne

d

e

th

e

d

esc

sc

e
r
,

er DR-5010C

in

Cano

m

rib

r

t

a

i

h

b

e

k

is

es

e

d

n

E

s

i
n

th

DR

a

u

s

r

th

e

e

y

-501

e

p

t

S

o

W

r

U

t

o

a

t

h

s

h

ce

r

0C D

e

e

t

or

If an

n

r

G

d

’

ou

s

you

ur

u

G

i

g

o

e

d

d

y of

u

c

h

f

e

C

e

un

i

u

l

or

d

a

y

t

me

o

e

le

h

t

r

p

sett

h

e

se

p

r

a

e

or

a

n

e

a

c

d

t

t

ite

c

k

i

up

Sc

n

c

ka

th

se

y

g

ms

our

k

e

ann

up

ge

r

th

v

U

i

ice

l

e

d

i

n

s

s

sc

e

t

h

sc

e

t

w

r

e

.

g

e

r’

r

a

d

it

e

s

an

nn

s

h

pr

t

b

G

c

n

t

e

e

ese

an

h

u

e

h

r

l

e

,

o

i

r

d

.

n

m

w

D

e

s

e

n

e

c

a

a

.

t

r

e

a

a

fo

k

r

t

P

ti

n

e

e

a

v

n

r u

il

s

e

mi

a

e

s

ur

.

r.

se

on

ssi

c

e

B

.

a

k

e

n

u

F

l

for

g

s

l

o

o

a

i

o

ll

n

e

f

o

g

g

r

y

t

w

h

d

t

o

e

h

e

a

t

u

h

e

m

f

e

o

st

Co

a

ll

ar

ge

o
w

t u

d

i
n

,

n

s

g

c

i
n

a

o

te

g

n

cc
t
a

n

ess

ct

ts

y

or

our

ie
s

lo

ar
c
a

e
l
au

in
c

t

lu

hor

d
e

iz

d

e

.

d

C
ano

n

Document Eject Guide

Easy Start Guide

(This Manual)

User’s Guide

Adobe Acrobat

Setup Disc

Warranty Card

(U.S.A and Canada only)

DR-5010C

Setup Disc

0880281099-L5T1P7-BR01

CANON CANADA INC.
6390 DIXIE RD
MISSISSAUGA ON L5T 9Z9

Registration Card

(U.S.A and Canada only)

The DR-5010C Setup Disc is
inserted in the User's Guide.

● The DR-5010C Setup Disc contains the Softwares (DR-5010C Scanner Driver

and CapturePerfect3.0) and PDF manuals. For details, refer to “About the Setup
Disc” on page 16 of the User’s Guide.

● Items included in this package are subject to change without notice.

● Keep the package and packing materials for storing or transporting the scanner.

D

ocu

ment S

c

ann

er

After checking the package contents, you need to remove all the
packing materials protecting the scanner. (☞STEP2)

Removing the Packing Materials

After unpacking the scanner, perform the following steps to remove all the orange
tape and protective materials from it.

The scanner is now ready for use.
Next, you need to install the scanner software. (☞STEP3)

Installing the Software

Install the software before connecting the scanner to the computer.

■ Trademarks

• Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or
registered trademarks in other countries.

• Microsoft Windows® is a registered trademark of Microsoft USA in the United States and other countries.

• Other brands and product names used in this manual may be trademarks or registered trademarks of their respective
companies.

PUB. CE-IE-672

©2008 CANON ELECTRONICS INC.

❏ Do not connect the scanner to the computer before installing the software.

In a Windows 2000/XP/Vista environment, if you connect the scanner and
turn it ON before you install the software, a wizard screen will appear.
If this wizard appears, click [Cancel] to exit the wizard, and then turn the
scanner OFF.

Wizard Screen (Windows 2000)

❏ Close all other applications before installing the software.

Continued on back side

☞

Continued from front side

1.

Launch CapturePerfect 3.0 from the Programs menu in Windows.

2.

Select [Select Scanner] from the Scan menu.

The Scanner Selection dialog box appears.

3.

Select [Canon DR-5010C] and click [OK].

12.

When all installations are complete, the
installation completed screen appears.

Click [Exit] to exit the installer. Click [Back] to
return to the menu screen.

1.

When connecting the scanner with a SCSI cable, turn your computer OFF.

2.

Make sure the scanner’s power switch is in the OFF position.

If the power switch is in the ON position, press the switch to turn it to the OFF
position.

OFF Position

Power Switch

ON Position

3.

Plug the power cord into the power connector on the rear of the scanner (

11

11

1).

4.

Plug the power cord into the power outlet (

22

22

2).

5.

When connecting the scanner with a USB cable, use the supplied USB cable.

Type B

Type A

6.

Follow the steps below when connecting the scanner to your computer with a
SCSI cable.

6-1

Turn OFF your computer.

Make sure your computer is turned OFF before connecting the SCSI cable.

SCSI Connector
(Half-pitch 50-pin, pin-type)

USB Connector

Imprinter Connector

SCSI ID
Dip Switches

Power Connector

Note

Warning

6-2

Connect the scanner to your computer with the SCSI cable.

SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the
shape of the connectors on your SCSI card and the scanner.

Warning

Warning

1.

Check the connection between the scanner and the computer.

2.

Press the power switch to turn the scanner ON (when connecting by SCSI).

The power indicator and start key indicator both light green.

3.

Turn ON your computer.

ON Position

Power Switch

Power indicator

Start key

4.

Windows recognizes the DR-5010C as new hardware and performs installation
automatically.

(Windows 2000)

(Windows XP) (Windows Vista)

Note

1

ON

2

Default Position (SCSI ID=2)

SCSI ID

2
3
4
5

SW1
OFF

ON

OFF

ON

SW2

OFF
OFF

ON
ON

OFF

Dip Switches

☞

This completes the software installation.

●

For Windows XP/Vista, a balloon help pop-up appears when installation is finished.

(Windows XP) (Windows Vista)

● The installation finished message does not appear in Windows 2000.

● The scanner is registered on the computer as “CANON DR-5010C USB” (or

“CANON DR-5010C SCSI”) in the “Imaging Device” directory of the Device
Manager.

Next, you need to connect the scanner to your computer. (

STEP4)

☞

Connecting the Scanner to Your PC

The scanner can be connected to a computer in two ways: by USB connection to a
standard USB port on the computer, or by SCSI connection to a SCSI card installed in
one of the computer’s expansion slots. Select a connection method appropriate to
your computing environment.

❏ When using the scanner in a daisy chain connection with other SCSI devices,

pay attention to the following points:

● The default setting for the SCSI ID is “SCSI ID=2.” Set the dip switches so
that the scanner’s SCSI ID is different from all other SCSI devices on the
chain.

● The scanner has a built-in SCSI terminator that is permanently set to [ON].
When using the scanner in a daisy chain connection, make sure that it is
connected as the terminating device and that the terminators of all other
SCSI devices in the chain have been set to [OFF].

The scanner is now correctly recognized by your computer.
Next, you need to select the scanner with the scanning software.

(☞STEP6)

Selecting the Scanner

You must select your scanner before using it with an ISIS- or TWAIN-compatible scanning
application.
The menus and procedures for selecting the scanner are different for each application.
For details, refer to the manual for your scanning application when selecting the scanner.
This section explains the procedure for selecting the scanner with “CapturePerfect 3.0”.
For details on how to use CapturePerfect 3.0, refer to the “CapturePerfect 3.0 Operation
Guide” in the Programs menu of Windows.

❏ Do not use both a USB connection and a SCSI connection at the same time.
❏ Use only the supplied power cord.
❏ Connect the scanner to your computer while the scanner is turned OFF.
❏ Before connecting the scanner with a SCSI cable, turn your computer OFF.
❏ A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches

the shape of the connectors on your SCSI card and the scanner.

The scanner is now connected to your computer.
Next, you need to turn on the scanner and ensure Windows recognizes

it. (☞STEP5)

Turning On the Power (Scanner
Recognition)

When you turn the scanner connected to the PC ON, the plug-and-play function recognizes
the scanner, and the device driver is automatically installed.

❏ When the scanner is connected by a SCSI cable, always turn on the scanner

before the computer. Turning on the computer first may prevent it from recog­nizing the scanner properly.

❏ Log on to Windows with an account that has administrator privileges.
❏ Wait at least 10 seconds before turning the scanner on again after turning it

off.

❏ If the scanner will not be used for an extended period, be sure to unplug it

from the power outlet for safety.

● Windows 2000/XP/Vista possess an event feature that allows you to launch a

scanning application with the start key on the scanner. CapturePerfect 3.0
supports this feature and, once setup is complete, can be launched by pressing
the scanner’s start key.

● When multiple applications that support the event feature are installed, pressing

the start key displays an Event on device dialog box for selecting the desired
application.

● You can change the event settings to specify a priority application from among

multiple applications or to turn off the event feature. For details, refer to “Setting
the Event Function” on page 40 of the User’s Guide.

The setup is now complete

This completes the setup of the DR-5010C. Details on how to use the DR-5010C are
described in the User’s Guide packaged with the scanner. Before you start using the
scanner, make sure to thoroughly read the User’s Guide.