Bosch TDS1017GB, TDS1006GB User Manual

TDS 10…

•

After Sales Service

Great Britain

BSH Appliance Care Grand Union House Old Wolverton Road Milton Keynes MK12 5ZR +44 (0)8705 678910 www.boschappliances.co.uk

003TDS10..GB /07/06

This appliance has been designed exclusively for domestic use and must not be used for industrial purposes Carefully read through the instructions for use of the appliance and safeguard

them for future reference This appliance complies with international safety standards

General safety instructions

• Remove the protective cover from the soleplate before using the iron

• The appliance is to be connected and used in accordance with the information stated on the rating plate. This appliance must only be plugged into an earthed mains socket

• The iron must be used and placed on a stable surface

• When placed on its support, make sure that the surface on which the support stands is stable

• Do not use the iron if it has been dropped, shows visible signs of damage or if it is leaking water. It will have to be checked by an Authorised Technical Service centre before it can be used again

• The electrical plug on the mains cable must be unplugged from the mains socket before filling or emptying the water tank

• Do not leave the iron unattended while it is plugged in. Should you have to leave the area where you are ironing, unplug the iron from the mains socket

• Never plug the appliance into the mains supply if the cable or the appliance itself show visible signs of damage. Unplug the appliance from the mains supply after each use or if a fault is suspected

• Any works or repairs that the appliance may need, e.g. replacing a faulty mains cable, must only be carried out by qualified personnel from an authorised technical service center

• Never immerse the iron in water or any other liquid

• Keep the appliance out of the reach of children. Electric irons reach high temperatures and produce hot steam during use, so take special care not to burn or scald yourself

• Danger of electric shocks or fire

• The iron has a built in safety cut-out device which switches it off should it malfunction

• Never leave a hot iron standing on textiles or on the mains cable. Make sure it is completely cold before storing it away. Do not unplug it by tugging on the mains cable or leave the plug hanging freely

• We accept no responsibility for any damage caused as a result of misuse or improper use resulting from not following the instructions in this manual

• When using the iron for the first time it may produce certain vapors and odours that will die away after a few minutes

• The use of an extension cable suitable for a current greater than 10 amps is essential if your appliance is rated at 2.400 Watts or more. Cables for 10 amps or less may overheat. Lay the mains cable so that it is impossible to tug or trip on it.

Filling the water tank

• Unplug the iron

• Place the iron at an angle of 45º

Instructions for use

• Fill the tank but never above the “max” mark

• Only use clean tap water, without any type of additive. Any other type of liquid could damage the appliance

• To obtain better and longer steam production mix tap water with distilled water in the measures shown in the table below. Using distilled water as recommended in these instructions will also help to prolong the life of your iron if you live in a hard water area

Water hardness level Amount of distilled water / tap water

Very soft / soft 0 / 1 Average 0 / 1 Hard 1 / 1 (approx.) Very hard 2 / 1 (approx.)

Setting the temperature

• Check the temperature instructions shown on the care label of the garment you are ironing and set the temperature control to the corresponding position:

«•» ............................ Synthetics

«••» .......................... Silk - Wool

«•••» ........................ Cotton - Linen

• If you are not sure what type of material the garment is made from, start ironing on the lowest temperature setting

• Sort your garments based on their care labels, always starting with clothes that have to be ironed at the lowest temperature

• The pilot lamp will stay lit while the iron is heating up and go out once the selected temperature has been reached. Wait a few seconds after the lamp goes out before you start ironing. Once the iron is hot you can continue to iron even if the pilot lamp comes on again

Ironing with steam

• Make sure that there is water in the tank

• Turn the temperature selector to the steam “

• Set the steam regulator to the appropriate setting:

– Set the steam regulator to the “min” position for “••” temperature setting – Set the steam regulator to the “max” position for “•••” and “max”

temperature settings

• If you press the “motor-steam” button when the water tank is empty, you will hear a distinctive sound of the pump operating dry.

” area between “••” and “max”

Adjusting the steam flow

• The steam flow setting can be adjusted to suit the type of ironing. Turning the control knob to the left produces minimum steam flow, maximum steam flow can be achieved by turning it to the right.

• The control knob is also the appliance’s pilot lamp.

Ironing without steam

• Do not press the “motor-steam” button

• Select an appropriate temperature for the type of material being ironed

Spray

Ironing with jet of steam

• Set the temperature control to the “•••” or “max” position

• Press the jet of steam “

” button repeatedly at intervals of 5 seconds

Additional features: (dependent on model) Auto shut-off

A safety circuit carries out an initialization check when the iron is switched on. The red OFF lamp will flash and the circuit will proceed to preheat the iron for 2 minutes.

After such time, if the iron has not been moved for 8 minutes while in the upright position or 30 seconds while resting on its sole plate or on its side then the safety circuit will switch the appliance off automatically and the red OFF lamp will start to flash. To reconnect the iron just move it about gently.

• Make sure that there is water in the tank

• Press the spray “ ” button

Vertical steaming with jet of steam

• Never spray or aim steam at people !

• Set the temperature control to the “•••” or “max” position

• Hold the iron in an upright position 10-20 cm away from the object being steamed

• Press the “motor-steam” button or the “

” button at intervals of 5 seconds.

Anti-scale system

Your iron is equipped with an anti-scale system, this will reduce the build up of lime scale, consequently prolonging the life of the appliance. However, this system does not completely prevent the formation of lime scale. Please read the “After finishing each ironing session” section of the instructions for use. If you live in a hard water area, please also read the “Filling the water tank” section of the instructions for use

After finishing each ironing session

• Unplug the iron from the mains socket

• Empty out the water tank – hold the iron with the point facing down and shake it gently

• Coil the cable around the heel of the iron but not too tightly

• Leave the iron standing in the vertical position to cool down before storing

SOLVING MINOR PROBLEMS YOURSELF

Problem Possible causes Solution

Iron does not Temperature control set to Turn the temperature work or is Minimum selector to the desired not heating up position

Connection problems Check that the plug is inserted into the mains socket correctly

The automatic shut-off Move the iron gently from system has been activated side to side to re-start

Iron is not There is no water in the tank Fill the water tank steaming The temperature control is set Set the temperature control too low, the pump does not work within the steam because the temperature limiter between “••” and “max” is working

Water is You have pressed the jet of steam Wait 5 seconds between each dripping from button repeatedly without waiting press of the jet of steam button the holes in the 5 seconds between each press soleplate

Distilled water has not been Mix distilled water with tap water used (see section on filling the as directed in the table under water tank) or other products such “filling the water tank” and never as fragrant water have been add any other products to the added to the tank water tank

“ ”

area,

Cleaning and maintenance

Attention ! Risk of burns !

•

Clean the body of the iron and the soleplate with a damp cloth and then dry it

• In the event that the soleplate is heavily stained: when the soleplate is cold, iron a linen cloth soaked in white vinegar or stand the soleplate in a container with vinegar for 15 minutes (maximum depth 1mm). Then dampen a cloth with water and wipe the soleplate clean, then dry it thoroughly.

Or:

• To immediately remove any marks on the soleplate use a dry cotton cloth folded several times with the iron set to the maximum temperature setting

• Do not de-scale or clean the water tank with cleaning products or solvents, as these could cause the iron to drip when using the steam function

• Do not use a “professional steam cleaner” for cleaning the appliance

Advice on discarding used appliances

Before throwing a used appliance away, you should make it noticeably inoperable and be certain to dispose of it in accordance with current laws and regulations. Your retailer, town council or local council can give you detailed information about these.

Iron emits nois There is no water in the tank, Fill the water tank the pump is operating dry

This appliance is labeled in accordance with European Directive 2002/96/EG concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

GUARANTEE TERMS

The terms of the guarantee for this appliance are in accordance with that stated by our representative for the country in which it is sold. Details of those conditions can be obtained from the retailer from whom the appliance was purchased. The SALES RECEIPT must be presented when making any claims against the terms of this guarantee We reserve the right to make technical modifications