Bosch ISC-FPB1-W60QS, ISC-FPB1-W200QS, ISC-FPB1-W120QS Installation Manual
Photobeam 5000
ISC-FPB1-W60QS, ISC-FPB1-W120QS, ISC-FPB1-W200QS
en Installation and Operation Guide
Photobeam 5000 Table of Contents | en 3
Table of contents
1
1.1 About documentation 4
1.2 Bosch Security Systems, Inc 4
2
2.1 Features 5
2.2 Photobeam overview 6
2.3 Console overview 7
2.4 Transmitter/receiver dimensions 8
3
3.1 Beam spread 9
3.2 Pole mount installation 10
3.3 Wall mount installation 12
4
4.1 Terminal strip overview 13
4.2 Wiring distance 13
4.3 Wiring routes 14
5
5.1 Level LED 16
5.2 EDC (Environmental Discrimination Circuit) 16
5.3 Beam interruption time 17
5.4 Beam power control 17
6
7
7.1 Level LED – alignment of the Upper Beam 21
7.2 Level LED - alignment of the Lower Beam 21
7.3 Volt meter alignment 22
8
9
9.1 Additional information 25
10
11
Introduction 4
System overview 5
Installation 9
Wiring 13
Special features 16
Setup 18
Optical alignment 21
Operational check 23
Troubleshooting 24
Certifications 26
Specifications 27
Bosch Security Systems, Inc. Installation and Operation Guide 2014.10 | 01 | F.01U.305.910
4 en | Introduction Photobeam 5000
1
1.1
1.2
Introduction
This document contains information that a trained installer needs to install the Photobeam
5000 quad-beam photoelectric detector contained inside the packaging.
About documentation
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
Bosch Security Systems, Inc
Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. website at http://www.boschsecurity.com/datecodes/.
Manufacturing date information is contained in digit no 1 – 3: DDD.
2014.10 | 01 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.
Photobeam 5000 System overview | en 5
2
2.1
System overview
The ISC-FPB1-W60QS,
photoelectric detectors designed for indoor and outdoor applications. Consisting of a
separate transmitter and receiver, an alarm is activated when a person passes through all four
beams. Combination of features and adjustable parameters allow for better catch
performance, lower false alarm rates and reduced effects of environmental disturbances.
Features
For stable operation, the detectors are equipped with the following feautres:
100% Sensitivity Allowance
Maintains stable operation even if 99% of beam energy is cut by rain, fog, frost, and so on.
Quad Beam Detection
Fewer false alarms caused by birds and other small animals because all four beams must be
blocked simultaneously to cause an alarm.
Beam Power Control
Select the appropriate beam intensity relative to the detection range to minimize reflection on
nearby walls and cross-talk with other detectors.
Beam Interruption Time Control
Use to change the beam interruption time to best fit the application.
ISC-FPB1-W120QS and ISC-FPB1-W200QS are quad-beam
Bosch Security Systems, Inc. Installation and Operation Guide 2014.10 | 01 | F.01U.305.910
2
1
1
4
5
6
7
8
9
10
11
10
9
7
8
3
13
12
6 en | System overview Photobeam 5000
2.2
Photobeam overview
Photobeam components overview
1 ー Mounting holes 8 ー Optical alignment
2 ー Mounting plate 9 ー Vertical adjustment
3 ー Device securing screws 10 ー Horizontal adjustment
4 ー Wire entry 11 ー Console
5 ー Wiring terminals 12 ー Cover
6 ー Detector 13 ー Cover securing screws
7 ー Optical module
2014.10 | 01 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.
2
3
6
4
8
7
1
5
Photobeam 5000 System overview | en 7
2.3
Console overview
Console components overview
1 ー Transmitter console 5 ー Receiver console
2 ー Power Indicator 6 ー Status Indicators
3 ー Function switches 7 ー Sensitivity control
4 ー Beam Power Control 8 ー Alignment check terminals
Bosch Security Systems, Inc. Installation and Operation Guide 2014.10 | 01 | F.01U.305.910
1
103 mm (4.0 in)
19.3 mm
(0.75 in)
398 mm (15.66 in)
244 mm (9.60 in)
96 mm (3.77 in)
77.1 mm
(3.03 in)
337.7 mm (13.29 in)
56 mm
(2.20 in)
220 mm (8.66 in)
39 mm
(1.5 in)
39.7 mm
(1.56 in)
2
3
4
8 en | System overview Photobeam 5000
2.4
Transmitter/receiver dimensions
Transmitter/receiver dimensions
1 ー Knockout wire entrance 3 ー Center of the Upper Beam
2 ー Center of the Lower Beam 4 ー Wire entrance
2014.10 | 01 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.
1
5
4
3
2
Photobeam 5000 Installation | en 9
3
3.1
Installation
Prior to installing the devices, please review the installation considerations below:
– Install in an area that is clear of objects
– Install the transmitter/receiver within the maximum protection range of the model
–
Do not install:
– Receivers into intense sources of light (for example, rising and setting sun)
– On movable surfaces subject to vibrations
– Detectors where immersion to water, corrosive liquids, or exposure to high levels of
dust can occur
– Detectors in close proximity to strong electromagnetic noises
– Do not use detectors with other photobeam detectors or receivers
– Do not stack detectors
– Do not disassemble or modify this detector
– Do not install while the power is on
– Avoid extreme temperature and humidity ranges as defined in the products specifications
– Avoid installing detectors near magnets and/or magnetized materials
– Avoid beam interference between other units when multiple units are installed.
Beam spread
The beam spread angle is ±0.7 °from the transmitter to the receiver. Refer to the diagram and
table below to determine the installation conditions.
Beam distance and spread
1 ー Transmitter 4 ー Receiver
2 ー Horizontal spread (B) 5 ー Distance (A)
3 ー Vertical spread (C)
Bosch Security Systems, Inc. Installation and Operation Guide 2014.10 | 01 | F.01U.305.910
1
2
10 en | Installation Photobeam 5000
Distance, horizontal and vertical spread values: (A) / (B) / (C)
Metric Imperial unit
20 m / 0.5 m / 0.8 m 65 ft / 1.6 ft / 2.6 ft
40 m / 1.0 m /1.3 m 13.1 ft / 3.2 ft / 4.2 ft
60 m / 1.5m / 1.8 m 196 ft / 4.9 ft / 5.9 ft
80 m / 2.0 m / 2.2 m 262 ft / 6.5 ft / 7.2 ft
100 m / 2.5 m / 2.7 m 328 ft / 8.2 ft / 8.8 ft
120 m / 3.0 m / 3.2 m 393 ft / 9.8 ft / 10.4 ft
140 m / 3.5 m / 3.7 m 459 ft / 11.4 ft / 12.1 ft
160 m / 4.0 m / 4.2 m 524 ft / 13.1 ft / 13.7 ft
180 m / 4.5 m / 4.7 m 590 ft / 14.7 ft / 15.4 ft
200 m / 5.0 m / 5.2 m 656 ft / 16.4 ft / 17.0 ft
3.2
Pole mount installation
Pole mounting overview
1 ー Diameter 38 – 48 mm (1.50 – 1.87 in) 2 ー Back-to-back pole mounting
Attaching the mounting bracket
1. Choose an appropriate mounting location for the devices. Install the mounting poles with
a clear line-of-sight between the transmitter and receiver.
2. Loosen the transmitter’s cover mounting screw and remove the cover.
3. Loosen the two base mounting screws and remove the mounting plate by sliding it down.
4. Attach the mounting hardware to the mounting plate using the clamping screws. Refer to
the figure below.
2014.10 | 01 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.
Loading...