Bosch D9131A Operation Manual

User's Guide

Parallel Printer Interface Module D9131A

D9131A

D9131A User's Guide

34584G Page 2 © 2002 Bosch Security Systems

D9131A

Overview

1.0 Overview

1.1 Description

The printer installed with your security system records various types of events. You need a D9131A Parallel Printer
Interface Module to be able to use the printer. Your security system has been programmed by your security technician
to provide you with printed reports of activities such as Openings, Closings, Alarms, etc. This User’s Guide describes
the types of reports that can be printed, and explains the information contained in these reports. The manual that
comes with your printer explains printer functions such as how to load printer paper.

You can display events from your security system on a monitor; however, you will not retain a permanent record of
your system events this way.

1.2 Operation

The security system only remembers a certain number of events. If more than this number of events occur, new events
push out older events one by one. Your system has a Print Log command that allows you to print the entire history of
events stored in your system or you may select to print only events that have occurred from a specific date forward.

1.3 Printing Format

Your security system prints events with top and bottom margins and form feed between pages with descriptive headers.
Each event is printed on two lines. The first line contains the time and date the event occurred. The second line contains
the type of event and additional information.

EVENT ACCT AR ID PT# TEXT

01/01 01:21AM
Fire Alarm 1111 1 1 Hall Smoke
01/01 01:22AM
Fire Cancel 1111 1 002 1 John Smith
01/01 01:23AM
Fire Restoral 1111 1 1 Hall Smoke

Line 1:

• Date the event occurred at the panel

• Time the event occurred at the panel

Line 2:

• Event Description

Indicates the current armed status. The descriptions are listed alphabetically under Section 2.0 Event Descriptions and
Troubleshooting beginning on page 5.

• Account Number

• Area Number

• ID Number

USER XXX Event reported was initiated by this user ID.
USER XXX-0 Event reported was initiated with the Master User (Card/Token).
USER XXX-1,2,3 Event reported was initiated with the Sub User Noted (Card/Token).

• Point Number

D9131A User's Guide

© 2002 Bosch Security Systems Page 3 34584G

D9131A

Overview

• Text

Usually this is programmed by your alarm technician, however, the following text is not:
SDI XX- Event reported was initiated by the Serial Device Interface indicated. The numbers 1 through 8 indicate the

event is from one of the supervised command centers. The numbers 17, 18 or 19 indicate the event is from a printer.
Numbers 33 to 40 indicate the event is from the Access Control Module.

(The following text indicates previous armed status.)

Was Master Armed
Was Perim Delay
Was Perim Instant
Was Disarmed
Was Mstr Instnt

• User Text

Your alarm technician usually will program this. User text is printed whenever an event with a User ID is noted.

D9131A User's Guide

34584G Page 4 © 2002 Bosch Security Systems

D9131A

Event Description and Troubleshooting

2.0 Event Descriptions and Troubleshooting

The following events and their respective descriptions are listed in alphabetical order. Your system may not display all
of the events. For detail in the cause of events, see your Security System Owner’s Manual.

Event Description

Access Granted A card access holder has been granted access at the point specified.
AC Failure

AC Restoral
ALARM-Door Open An access door has been held open beyond the allowed time while the area was armed.
Alarm Report Alarm at device in area specified. This event also reports Cross Point Alarms, including

All Points
Tested

Bad Call To RAM

Battery Low Security system battery is low. Replace the battery.
Battery Missing

Battery Restore Security system battery has recharged.
Cancel Alarm User with reported ID canceled an alarm from the area specified.
Card Assigned
Command Bypass
Closing Early
Closing Late
Closing Report User with reported ID armed area.
Comm Failure Security system could not communicate using the phone number reported. Call for service.
Date Changed
Door Closed-

Restoral
Door Cycled
Door Left Open
Door Locked
Door Secured An access door in the area specified was secured, which prohibits access.
Door Unlocked An access door in the area specified was unlocked allowing free access.
Duress
Early to Open

Extra Point Area specified reports an unprogrammed device. Call for service.
Extn Close Time User with reported ID extended area’s closing time to that specified.
Fail To Close
Fail To Open
F Close Early
F Close Late User with reported ID force armed* specified area later than expected.
F Close Pr Dlay User with reported ID force armed* perimeter with entry/exit delay.
F Close Pr Inst
Fire Alarm
Fire Cancel See Cancel Alarm.
Fire Restoral The fire trouble or alarm event at the device specified has been restored.

AC power to the security system is interrupted. Check the plug-in transformer and the
circuit breaker.

AC power to the security system has been restored.

Cross Group (CG:##) information.
All points have been tested while in the Service Walk Test, Fire Walk Test, or Walk Test

mode.
System tried to call Remote Account To Ram Manager (RAM) and failed. Call your security

company.

Security system battery is disconnected or has discharged. Reconnect the battery; call for
service.

An access card/token was added to the system.
Device specified is bypassed.* System will not respond to faults at this point.
User armed area earlier than expected.
User armed area later than expected.

User with reported ID changed the date in the security system.
An access door in the area specified restored to normal after a Door Left Open event

has occurred.
An access door in the area specified was cycled.
The door specified has been left open past the programmed time.
An access door in the area specified was locked for normal operation.

User with reported ID manually initiated a special alarm in the area specified.
User disarmed area earlier than expected. If the entire security system is being disarmed,

the previous state of security system is indicated. If just one area is being disarmed, no
previous status is indicated.

Area failed to arm within your programmed closing window.
Area failed to disarm within your programmed opening window.
User with reported ID force armed* specified area later than expected.

User with reported ID force armed* area perimeter with no delay time.
Fire Alarm at device specified.

D9131A User's Guide

© 2002 Bosch Security Systems Page 5 34584G

D9131A

Event Description and Troubleshooting

Event Description

Fire
Supervision

Fire
Supervision
Restoral

Fire Trouble
Fire Walk End Walk test* for fire devices in the area specified is complete.
Fire Walk Start A walk test* is in progress for fire devices in the area specified.
Forced Close
Forced Point
Late To Close
Late To Open

Log Overflow
Log Threshold
Missing Alarm
Missing Fire Fire device in area specified is not reporting. Call for service.
Missing Trouble Trouble Condition at area device specified.
Msng

Supervision
No Entry -

Level
No Entry -

Interlk
No Entry -

Secured
No Entry -

Unknown
Opening Report
Params Changed
Peri Dlay Armed
Peri Inst Armed User with reported ID armed the perimeter of the specified area with no delay time.
Phone Line Fail The phone line specified is not working. Call for service.
Phone Restoral
Point Bypass
Point Closing
Point Opening User disarmed device in area specified.
Point Status Status report for device in area specified.
Point Tested
Prog Access Ok
Pt Bus Trouble
Pt Bus Restoral Wiring problem is resolved.
Ram Access Fail Technician could not access your security system from the security company.
Ram Access Ok
Re-Boot
Relay Reset
Relay Set
Request To A Request To Enter device for an access door has been activated.

Supervision condition at the fire point specified.

Supervision condition at the fire point specified has been restored.

Trouble condition at area device specified.

User with reported ID armed area with point(s) faulted.
User force armed device in area reported.
User with reported ID armed the security system later than expected.
User with the reported ID disarmed area later than expected. If the entire security system is

being disarmed, the previous state of the system is indicated. If just one area is being
disarmed, no previous state is indicated.

Security system event log is full. Events are being overwritten.
Security system event log is at the programmed maximum capacity.
Device in area specified is not reporting. Call for service.

Supervision device at area specified is not reporting.

An access card holder attempted access but was denied due to the user’s authority level.

Access was denied due to the interlock door being open.

Access was denied due to the door being secured.

Access was denied because the user was not found in the database.

User with reported ID disarmed area.
Security system programming has been changed.
User with ID reported armed the perimeter of the specified area with delay time.

The problem with the phone line specified has been restored.
Area device specified is bypassed.* System will not respond to faults at this device.
User armed device in area specified.

This device has been walk tested.*
Account has been accessed locally by the device specified.
Wiring problem. Call for service.

Your security company accessed your system from the security company.
Your security system was reset.
Relay has reset.
Relay specified has been turned on.

D9131A User's Guide

34584G Page 6 © 2002 Bosch Security Systems

D9131A

Event Description and Troubleshooting

Event Description

Enter
Request To Exit
Restoral Report
RF Low Battery
RF Batt Restor The Low Battery condition previously sent from the point specified has restored.
RTE Deny

Intrlok
RTE Deny

Secured
REX Deny

Intrlok
REX Deny

Secured
S: Alarm
S: Closing
S: Fire

Supervision
S: Opening
S: Perim Delay
S: Perim

Instant
S: Supervision
S: Trouble Status report: trouble at area specified.
SDI Failure Serial Device Interface specified is not reporting. 1-8 = command centers; 017, 018, 019 =

SDI Restoral
Sensor Reset
Service End
Service Start A Service Walk Test in the specified area has started.
Sked Bypass Sked* in area specified is bypassed.* System will not respond to faults at this device.
Sked Changed
Sked Executed
Status report
Supervision
Swinger Bypass

Test Report
Time Changed

A Request To Exit device for an access door has been activated.
Restoral at point in area specified.
A Low Battery condition at the point specified has been detected.

A Request To Enter device has been activated but was denied due to the interlock door
being open.

A Request To Enter device has been activated but was denied due to the door being
Secured. See Door Secured.

A Request To Exit device has been activated but was denied due to the interlock door being
open.

A Request To Exit device has been activated but was denied due to the door being Secured.
See Door Secured.

Status report: alarm at area specified.
Status report: closing at area specified.
Status report: Fire Supervision at area specified.

Status report: opening at area specified.
Status report: area perimeter specified is armed with entry/exit delay.
Status report: area perimeter specified is armed (no delay).

Status report: Supervision at area specified.

printers; 33-40 = Access Control Module. 80 = Home Automation;
88 = RAMIV/Netcom. Make sure the device is plugged in.
The problem with the device specified is resolved.
User with reported ID reset detection devices in area specified.
A Service Walk Test in the specified area has ended.

User with reported ID changed the Sked* indicated.
Sked* was activated.
Status report was sent to the receiver.
Supervision condition at point specified.
Area specified had four alarm or trouble signals within an hour. It is now bypassed from the

system.
Test report was sent.
User with reported ID changed the time in the security system.

D9131A User's Guide

© 2002 Bosch Security Systems Page 7 34584G

D9131A

Event Description and Troubleshooting

Event Description

Trouble Door
Open

Trouble Report
Unverified

Event
User Alarm Cmd7
User Alarm Cmd9
Usr Code Change
Usr Code Delete User ID specified was deleted.
User Level Set The authority level of the specified user has been modified.
User Tamper
Walk End
Walk Start
Was Force Armed
Watch Mode Start The Watch Mode in the specified area has started.
Watch Mode End The Watch Mode in the specified area has ended.
Watchdog Reset

* For an explanation of terms, see your Security System Owner’s Manual.

Access door was left open beyond the programmed time.

Trouble condition at device specified.
The point specified generated an unverified alarm event.

User with reported ID manually initiated special alarm in the area specified.
User with reported ID manually initiated special alarm in the area specified.
User ID specified was changed.

User with wrong ID tried to access specified area.
Walk test in area specified is complete.
A walk test is in progress in the area specified.
User with the reported ID force armed* account with point(s) faulted.

Panel was internally reset.

© 2002 Bosch Security Systems 34584G

User's Guide

10/02

D9131A

Page 8 of 8