Bosch D9127T, D9127U User Manual
1 | Overview
The D9127 Series POPIT Modules includes
the D9127T (with magnetic tamper switch)
and the D9127U (without tamper). They
are used with a compatible control panel
to expand beyond its standard number of
on-board initiating points. Future system
expansion is very economical as D9127
Series POPITs can be added anywhere
along the two-wire data expansion loop.
Both modules include proven technology
that combines point supervision with
individual device addressing on one pair
of wires. Screw terminals provide reliable
connections for the data expansion loop
and supervised sensor loop wiring.
The units are small and easily installed in
standard outlet boxes, above false ceilings,
closets, or other accessible locations.
2 | Installation
Use the steps in this section to install and
configure the POPIT module.
2.1 | Remove the cover
1. Insert a small flat-head screwdriver into
one of the small slots in the side of the
POPIT.
2. Twist the screwdriver and remove the
cover.
2.2 | Remove the PCB
1. Grasp the terminal block on the PCB in
one hand.
2. Three tabs hold the PCB. At the end with
the two tabs, carefully but firmly, push
one tab away from the PCB and lift the
corner.
3. Carefully but firmly, push the other tab
away from the PCB and lift the entire
PCB from the base.
2.3 | Mount the POPIT base
Pull the wiring through the wiring opening
(refer to Figure 1). Mount the POPIT base
using the supplied hardware to prevent
shorting the PCB.
2.4 | Replace the PCB
1. Grasp the terminal block on the PCB with
one hand. Insert the DIP switch end of the
PCB under the single tab.
2. Carefully but firmly, pull the two tabs on
the opposite ends away from the PCB.
3. Gently lay the PCB in place and, if
necessary, carefully, push the two tabs
toward the PCB until the PCB is firmly in
place.
2.5 | Configuration of DIP switch
Refer to Table 1 for DIP switch 0 settings and
Section 4 for DIP switch configuration settings
for ZONEX and ZONEX 2.
Control
panel
D7212B1
D8112
D9112B1
D9412 Refer to 9000 Series
D9412G
D7412G
D7212G Refer to Section 4.
D7212GV2 Refer to Section 4.
D7212GV3 Refer to Section 4.
D7212GV4
D9412GV4
D7412GV4
B9512G
B9512G-E
B8512G
B8512G-E
For additional D9127 installation
information, refer to the compatible panel
installation documentation.
Table 1: DIP switch 0 setting
DIP switch 0 setting
Leave switch 0 ON.
Operation
and Installation Guide
(P/N: 74-07692-000).
Refer to Section 4.
Refer to Section 4.
Refer to Section 4.
3 | Wiring Instructions
For more information on POPIT installation (including wire type, length, and run) and
programming, refer to the D8125 POPEX Operation and Installation Guide (P/N: 74-04247-000)
and control panel operation, installation, and programming manuals.
resistor at the farthest point on the loop for proper supervision. Replace the POPIT cover
when the wiring is completed.
NOTICE!
When using 12 AWG (0.1 mm) maximum wire, use solid wire. If you use stranded
wire, take care to insert all of the strands into the terminal block.
1
GND
OUT
AUX
4
5
-
+
+
- - + + - +
IN
3
11
DATA
10
3
2
LOOP
8
3
(-)
(+)
Figure 1: POPIT Wiring
Callout ― Description
1 ― D8125 POPEX Module
2 ― D9127U/T POPIT Module
3 ― Tab
4 ― DIP Switch
5 ― Reed switch (D9127T only)
6 ― Detector loop
7 ― 33 kΩ EOL resistor
8 ― Terminals (all): 12 AWG solid (maximum); 22 AWG (0.1 mm) stranded (minimum)
9 ― Zone expansion loop to other POPITs
10 ― Supervised
11 ― Wire opening of POPIT base
Install a 33 kΩ end-of-line
6
7
9
© 2016 Bosch Security Systems, Inc.
4998132020 | 11 | 2016.01
en Installation Guide
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.us
4 | ZONEX and ZONEX 2 point address chart
Bosch Sicherheitssysteme
GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
1
Address
ZONEX
ZONEX
1
2
009 129 x00*
010 130 x01*
011 131 x02*
012 132 x03*
013 133 x04*
014 134 x05*
015 135 x06*
016 136 x07*
017 137 x08*
018 138 x09
019 139 x10
020 140 x11
021 141 x12
022 142 x13
023 143 x14
024 144 x15
025 145 x16
026 146 x17
027 147 x18
028 148 x19
029 149 x20
030 150 x21
031 151 x22
032 152 x23
033 153 x24
034 154 x25
035 155 x26
036 156 x27
037 157 x28
038 158 x29
039 159 x30
040 160
041 161
042 162
043 163
044 164
045 165
046 166
047 167
048 168
049 169
050 170
051 171
052 172
053 173
054 174
055 175
056 176
057 177
058 178
059 179 x50
1
ZONEX 1: Points 9 to 127 (D9412G); Points 9 to 75 (D7412G).
ZONEX 2: Points 129 to 247 (D9412G).
B299: x = B299 module address 0-5
* These point numbers are not available for B299 address 0.
Switch
0 1 2 3 4 5 6
B299
ON ON ON ON ON ON ON
ON ON ON ON ON ON
ON ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON
ON ON ON
ON ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON
ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON
ON ON ON
ON ON ON ON
ON ON ON
ON ON ON
x31
ON ON
x32
ON ON ON ON ON ON
x33
ON ON ON ON ON
x34
ON ON ON ON ON
x35
ON ON ON ON
x36
ON ON ON ON ON
x37
ON ON ON ON
x38
ON ON ON ON
x39
ON ON ON
x40
ON ON ON ON ON
x41
ON ON ON ON
x42
ON ON ON ON
x43
ON ON ON
x44
ON ON ON ON
x45
ON ON ON
x46
ON ON ON
x47
ON ON
x48
ON ON ON ON ON
x49
ON ON ON ON
ON ON ON ON
1
Address
ZONEX
ZONEX
1
2
060 180 x51
061 181 x52
062 182 x53
063 183 x54
064 184 x55
065 185 x56
066 186 x57
067 187 x58
068 188 x59
069 189 x60
070 190 x61
071 191 x62
072 192 x63
073 193 x64
074 194 x65
075 195 x66
076 196 x67
077 197 x68
078 198 x69
079 199 x70
080 200 x71
081 201 x72
082 202 x73
083 203 x74
084 204 x75
085 205 x76
086 206 x77
087 207 x78
088 208 x79
089 209 x80
090 210
091 211
092 212
093 213
094 214
095 215
096 216
097 217
098 218
099 219
100 220
101 221
102 222
103 223
104 224
105 225
106 226
107 227
108 228
109 229
110 230
1
ZONEX 1: Points 9 to 127 (D9412G); Points 9 to 75 (D7412G).
ZONEX 2: Points 129 to 247 (D9412G).
B299: x = B299 module address 0-5
* These point numbers are not available for B299 address 0.
Switch
0 1 2 3 4 5 6
B299
ON ON ON
ON ON ON ON
ON ON ON
ON ON ON
ON ON
ON ON ON ON
ON ON ON
ON ON ON
ON ON
ON ON ON
ON ON
ON ON
ON
ON ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON
ON ON ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON
ON ON ON
ON ON ON ON
ON ON ON
ON ON ON
ON ON
x81
x82
x83
x84
x85
x86
x87
x88
x89
x90
x91
x92
x93
x94
x95
x96
x97
x98
x99
ON ON ON ON ON
ON ON ON ON
ON ON ON ON
ON ON ON
ON ON ON ON
ON ON ON
ON ON ON
ON ON
ON ON ON ON
ON ON ON
ON ON ON
ON ON
ON ON ON
ON ON
ON ON
ON
ON ON ON ON ON
ON ON ON ON
ON ON ON ON
ON ON ON
ON ON ON ON
ON ON ON
1
Address
ZONEX
ZONEX
1
2
111 231
112 232
113 233
114 234
115 235
116 236
117 237
118 238
119 239
120 240
121 241
122 242
123 243
124 244
125 245
126 246
127 247
128 248
1
ZONEX 1: Points 9 to 127 (D9412G); Points 9 to 75 (D7412G).
ZONEX 2: Points 129 to 247 (D9412G).
B299: x = B299 module address 0-5
* These point numbers are not available for B299 address 0.
Switch
0 1 2 3 4 5 6
B299
ON ON ON
ON ON
ON ON ON ON
ON ON ON
ON ON ON
ON ON
ON ON ON
ON ON
ON ON
ON
not available
ON ON ON ON
ON ON ON
ON ON ON
ON ON
ON ON ON
ON ON
ON ON
5 | Specifications
Operating Voltage Nominal 12 VDC
Operating Current
per D9127U/T
Copyright
This document is the intellectual property of
Bosch Security Systems, Inc. and is protected
by copyright. All rights reserved.
Trademarks
All hardware and software product names used
in this document are likely to be registered
trademarks and must be treated accordingly.
Bosch Security Systems, Inc. product
manufacturing dates
Use the serial number located on the product
label and refer to the Bosch Security Systems,
Inc. website at
http://www.boschsecurity.com/datecodes/.
supplied by control
panel
0.8 mA Standby
0.8 mA Alarm
POPIT Module
D9127U/T
Loading...