BioMerieux 416036 User Manual

Intentionally left blank.

Document history

VERSION DATE MODIFICATIONS

A 05/11/2013 Creation

User manual - Pictograms

Note

Equipment optimization tip

Prohibited action notice

Noteworthy point warning

Danger or potential risk warning

Reminder of the pre-requisites for implementation of the next instructions

Labguard™ is one of bioMérieux's registered trademarks.

The information and graphs contained in this manual are not binding. bioMérieux therefore reserves
the right to implement changes to the document without prior notice.

bioMérieux will not approve any modifications whatsoever to the equipment implemented by
the user. bioMérieux shall under no circumstance be held liable for any direct or
consequential injury or damage whatsoever suffered by the user or by any third party, as a
result of modifications to the equipment.

• This equipment is for professional use only.

• Users are required to read all the accompanying documents, including the statutory
information, before using the equipment.

Contents

Unpacking the device ........................................... 6

Learning about the equipment ...................................... 7

Labguard 3D™ equipment ..................................... 7

Front ................................................. 7

Installing the device ............................................ 8

Understanding the indicator lights .................................... 9

Technical characteristics ......................................... 10

Maintenance ............................................... 11

Disposal .............................................. 11

Cleaning the device ........................................ 11

Options and accessories ......................................... 12

Equipment conformity .......................................... 13

FCC compliance .......................................... 13

Industry conformity Canada (IC) ................................. 13

EC compliance ........................................... 14

Compliance statement .................................... 14

1

Unpacking the device

Check that the device has not been damaged during transport. Then check that all the accessories
listed below are present.

Transmitter

• RJ45 cable 3 m

• µUSB/USB cable 2 m

• Unit

• Unit support

Labguard 3

6

RECEPT_QSG_EN-A

2

Learning about the equipment

Labguard 3D™ equipment

With Labguard 3D™ equipment, you can:

• Simultaneously measure the different physical parameters of the laboratory (temperature,
humidity, CO2).

• Provide alerts with visual alarms in real time in case of anomalies.

• Save and transfer data and alarms to the Labguard® software.

Front

1 Accessory connector
2 Ethernet connector
3 MicroUSB connector

Labguard 3

7

RECEPT_QSG_EN-A

3

Installing the device

1. Fix the receiver support to the wall or to the unit to be monitored using the two screws or

adhesive strips at the rear of the support.

2. Slide the device into the support.

3. Connect the Ethernet cable.

4. In the case where the installation is not PoE, plug in the external power source using the

microUSB connector.

Labguard 3

8

RECEPT_QSG_EN-A

4

Understanding the indicator lights

The indicator lights present on the front of the unit show the status of the Ethernet connection.

Indicator lights Status

Device connected to mains power supply

Alarm in communication network

Labguard 3

9

RECEPT_QSG_EN-A

5

Technical characteristics

Environmental
conditions

Atmospheric pressure 700 hPa to 1,100 hPa
Installation category Type II according to Directive CEI 664
Device dimensions (W x H x D) Device (mm):

Device weight Device (g):

Connectivity • Ethernet

Wireless Emission bandwidth:

Altitude up to 2,000 m
Temperature from 0 to 40°C max.
Relative humidity (Rh) from 10 to 80%
Mains power supply Input:

100-240 VAC;
50/60 Hz; 0.3 A

Product power supply Mains power:

• 5 V ; 1 A; 5 W

Power Over Ethernet
(IEEE 802.3af)

Pollution level 2

48 V ; Class 1; 0.44 to 3.84 W

• 55 x 103 x 31

• 90

• USB

• Labguard 3D sensor

Output:

5 V ; 1 A; 5 W

Device in packaging (mm):

• 167 x 133 x 74
Device in packaging (g):

• 305

Range:

• 865 to 868 Mhz,
60 channels

• 868 to 868.8 Mhz,
12 channels

• 902 to 912 Mhz,
20 channels

• 433.05 to

434.79 Mhz,
8 channels

• 100 m inside

• 400 m outside

Labguard 3

10

RECEPT_QSG_EN-A

6

Maintenance

Disposal

Recycle the lithium batteries in accordance with enforceable regulations.

Dispose of them by the appropriate means put in place.

Cleaning the device

Clean the equipment using a cloth dampened with ethanol or any other common disinfectant.
However, avoid using formol, solvents, heat greater than 80°C (flames, autoclaving) or cleaning by
dipping or spraying.

Labguard 3

11

RECEPT_QSG_EN-A

7

Options and accessories

Use the following options and accessories for optimum use of the device.

Reference Designation

416053 Mains power supply µUSB_EU
416055 Mains power supply µUSB_UK
416054 Mains power supply µUSB_US
416056 Mains power supply µUSB_AU/CN
416057 Sensor extension cable 1 m
416070 µUSB/USB cable 2 m
416072 RJ45 cable 3 m

Labguard 3

12

RECEPT_QSG_EN-A

8

Equipment conformity

FCC compliance

This equipment has been declared in compliance with FCC regulations, section 15, applicable to class
B digital equipments. These regulations are designed to provide adequate protection against harmful
interferences in a residential installation. This equipment generates, uses and may emit radio-electric
waves. It can generate interferences that may be harmful to radio-communications if it is not
installed or used according to the instructions. Using this equipment in a specific installation may
generate harmful interferences, in which case the user may need to correct the interference using
one or all of the following methods:

• Redirect or move the receiver aerial

• Move the equipment away from the receiver

• Plug the equipment into a different socket from the one used for the receiver

• Contact the distributor or get help from a radio / TV technician.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

• this device may not cause harmful interference.

• this device must accept any interference received, including interference that may cause
undesired operation.

This equipment complies with FCC’s radiation exposure limis set forth for an uncontrolled
environment under the following conditions:

• This equipment should be installed and operated such that a minimum separation distance of
20cm is maintained between the equipment and user’s/neraby person’s body at all times.

• This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the
party responsible fr compliance. Such modifications could void the user's authority to operate the
equipment.

Industry conformity Canada (IC)

This class B digital equipment complies with Canadian standard NMB- 03.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions :

• this device may not cause interference.

• this device must accept any interference, including interference that may cause undesired
operation.

Labguard 3

13

RECEPT_QSG_EN-A

EC compliance

This class B numeric equipment complies with the relevant EC directives and standards listed in the
accompanying certificate(s). Class B equipment is equipment suitable for use in domestic
establishments and in establishments directly connected to a low voltage power supply network
which supplies buildings used for domestic purposes. Class B equipment shall meet class B limits.

Compliance statement

Via this statement, we bioMérieux SA

69280 MARCY l’ÉTOILE- FRANCE

hereby declare that the product designated hereafter - as a result of its design and its type as well as
the model that we have put into circulation - meets the fundamental health and safety requirements
defined by the EC directive concerned.

This statement shall be rendered invalid by any modification not approved by us.

Machine designation: Monitoring hardware
Model and reference type:
Applicable EC directives: • EC low voltage Directive (2006/95/EC)

• EC-ECM directive (2004/108/EC)

•

Harmonized standards applied in
particular:

The technical documents were
written by:

Date / Manufacturer's signature: 13 June 2013

Signatory's position: Instrument R & D Manager

EN 61010-1 (Ed. 2010): 2010, EN 61326-1 (Ed. 2006): 2006, EN
301 489-3 (Ed. 2002 V1.4.1): 2002 V1.4.1 EN 300-220-2 V2.4.1

EN 62479: 2010

Mr Develon
(Authorized person for documentation)

Labguard 3

14

RECEPT_QSG_EN-A

Intentionally left blank.

Intentionally left blank.

Intentionally left blank.

Intentionally left blank.

Intentionally left blank.