Washing Machine |
User’s Manual |
BFL7510W |
EN |
Document Number= 2302061401_EN/26-03-19.(09:15) |
1 General safety instructions
This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.
1.1 Life and property safety
uNever place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.
uUnplug the product if it is not in use.
uAlways have the installation and repairing procedures carried out by the
Authorised Service Agent. The manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.
uThe water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
uWhile there is still water inside the product, never open the loading door or remove the filter. Otherwise, risk of flooding and injury from hot water will occur.
uDo not force open the locked loading door. The door will open immediately after the washing cycle has ended. If the door does not open, apply the solutions provided for "Loading door cannot be opened." error in the Troubleshooting section. In case of forcing the loading door to open, the door and the lock mechanism may get damaged.
uUse detergents, softeners and supplements suitable for automatic washing machines only.
uFollow the instructions on the label of textile products and the detergent package.
1.2Children's safety
uThis product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or
This product was manufactured using the latest technology in environmentally friendly conditions.
2 / EN |
Washing Machine / User’s Manual |
trained on the safe usage of the product and the risks it brings out. Children should not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children under the age of 3 should be kept away unless continuously supervised.
uPackaging materials are dangerous for the children. Keep packaging materials in a safe place away from reach of the children.
uElectrical products are dangerous for the children. Keep children away from the product when it is in use. Do not allow them to play with the product. Use child lock to prevent children from intervening with the product.
uDo not forget to close the loading door when leaving the room where the product is located.
uStore all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.
1.3Electrical safety
uIf the product has a failure, it should not be operated unless it is repaired by the Authorised Service Agent! There is the risk of electric shock!
uThis product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.
uPlug the product into a grounded outlet protected by a 16 A fuse.
uDo not wash the product by spraying or pouring water onto it! There is the risk of electric shock!
uNever touch the power cable plug with wet hands! Never unplug by pulling on the cable. Always press on the plug with one hand and pull out the plug by grabbing with the other hand.
uProduct should be unplugged during installation, maintenance, cleaning and repair procedures.
uIf the power cable is damaged, it must be replaced by the manufacturer,
authorised service agent or a similarly qualified person (preferably an electrician) or in order to avoid possible risks.
1.4Hot surface safety
The glass of the loading door gets too hot while washing at higher temperatures. Therefore, especially do not allow children touch the loading door glass while washing.
Washing Machine / User’s Manual |
3 / EN |
2 Important instructions for environment
2.1 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.
2.2 Package information
Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.
3Intended use
•This product has been designed for domestic use. It is not for commercial purposes or it should not be used out of its intended use.
•The product must only be used for washing and rinsing of laundry that are marked accordingly.
•The manufacturer waives any responsibility arisen from incorrect usage or transportation.
4Technical specifications
Supplier name or trademark |
Beko |
|
|
|
|
Model name |
BFL7510W |
|
|
|
|
Rated capacity (kg) |
7.5 |
|
|
|
|
Maximum spin speed (rpm) |
1200 |
|
|
|
|
Built-in |
No |
|
|
|
|
Height (cm) |
84 |
|
|
|
|
Width (cm) |
60 |
|
|
|
|
Depth (cm) |
64 |
|
|
|
|
Net weight (±4 kg.) |
74 |
|
|
|
|
Single Water inlet / Double Water inlet |
• / - |
|
|
||
• Available |
||
|
||
|
|
|
Electrical input (V/Hz) |
220-240 V ~/ 50Hz |
|
|
|
|
Total current (A) |
10 |
|
|
|
|
Total power (W) |
2000-2350 |
|
|
|
|
Main model code |
138 |
|
|
|
Technical specifications may be changed without prior notice to improve the quality of the product.
4 / EN |
Washing Machine / User’s Manual |
4.1 Installation
•Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.
•Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.
•Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
4.1.1Appropriate installation location
•Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar surfaces.
•When the washing machine and dryer are placed on top of each other, their total weight –when loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!
•Do not place the product on the power cable.
•Do not install the product in the environments where the temperature falls below 0 ºC.
•Leaving a gap at the sides of the machine is suggested to reduce vibration and noise
•On a graduated floor, do not place the product next to the edge or on a platform.
•Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use them on the product.
4.1.2Removing packaging reinforcement (If the product has)
Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. Do not make this operation alone by yourself.
4.1.3 Removing the transportation locks
1Loosen all bolts with an appropriate wrench until they turn freely.
2Remove the transport safety bolts by turning them slightly.
3Insert the plastic covers in the bag containing the user manual to the openings on the rear panel.
A CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.
C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!
Washing Machine / User’s Manual |
5 / EN |
4.1.4 Connecting water supply
C The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have
10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.
A CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.
CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
1Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts.
2When hose connection is completed, check whether there is leak
problems at the connection points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. In order to prevent the water leaks and resultant damages, keep the taps closed when you do not use the product.
4.1.5Connecting the drain hose to the drain
•Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.
A CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine performs water intake and discharge processes without any problem, fix the drain hose securely.
100 cm 40 cm
•Connect the drain hose to a minimum height of 40 cm and a maximum height of 100 cm.
•In case the drain hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.
•To prevent the waste water to go back into the machine again and to ensure easy drainage, do not immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too long, cut it short.
•The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.
•If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.
6 / EN |
Washing Machine / User’s Manual |
spanner
4.2 Preparation
4.2.1Sorting the laundry
•Sort laundry according to type of fabric, color, and degree of soiling and allowable water temperature.
•Always observe the instructions given on the garment care labels.
4.2.2Preparing laundry for washing
•Laundry items with metal attachments such as, underwiring, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash such clothes by putting them in a laundry bag or pillow case.
•Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.
•Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
•Place curtains in without compressing them. Remove curtain attachment items.
•Fasten zippers, sew loose buttons and mend rips and tears.
•Wash “Machine washable” or “Hand washable” labeled products only with an appropriate programme.
•Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately.
•Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
•Only use the dyes / color changers and descaling agents which are appropriate for machine wash. Always follow the instructions on the package.
•Wash trousers and delicate laundry turned inside out.
•Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce piling.
•Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the product. Such dusts and powders on the laundry may build up on the inner parts of the product in time and can cause damage.
4.2.3Tips for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
•Operate the product in the highest load capacity allowed for the programme you have selected, but do not overload. See, "Programme and consumption table".
•Observe the temperature instructions on the detergent packaging.
•Wash slightly soiled laundry at low temperatures.
•Use faster programmes for small quantities of lightly soiled laundry.
•Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
•If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process.
•Do not use more detergent than the recommended on the detergent packaging.
4.2.4Loading the laundry
1.Open the loading door.
2.Put the laundry items into the product in a loose manner.
3Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door. The loading door is locked while a programme is running. The door lock will open immediately after the washing programme has ended. Then you can open the loading door. If the door does not open, apply the solutions provided for "Loading door cannot be opened." error in the Troubleshooting section.
4.2.5Correct load capacity
The maximum load capacity depends on the type of laundry, the degree of soiling and the desired washing programme.
The machine automatically adjusts the water amount according to the weight of the laundry put inside it.
A WARNING: Comply with the information in the section "Programme and consumption table". When overloaded, product's washing performance will drop. Moreover, noise and vibration problems may occur.
8 / EN |
Washing Machine / User’s Manual |
4.2.6 Using detergent and softener
C When using detergent, softener, starch, fabric dye, bleach and descaling agents; read the manufacturer's instructions written on the package and follow the dosages specified. Use measuring cup if available.
2 
3 1
The detergent drawer is composed of three compartments:
– (1) for prewash
– (2) for main wash
–(3) for softener
–(
) in addition, there is a siphon piece in the softener compartment.
Detergent, softener and other cleaning agents
•Add detergent and softener before starting the washing programme.
•While the washing cycle is in progress, do not leave the detergent drawer open!
•When using a programme without prewash, do not put any detergent into the prewash compartment
(compartment no. "1").
•In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment no.
"1").
•Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the detergent bag or the dispensing ball directly among the laundry in the product.
•If you are using liquid detergent, do not forget to place the liquid detergent container into the main wash
compartment (compartment no. “2”).
Choosing the detergent type
Detergent type to be used depends on the fabric type and color.
•Use different detergents for coloured and white laundry.
•Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) intended solely for delicate clothes.
•When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
•Wash woolens with special detergent made specifically for woolens.
A WARNING: Use only detergents manufactured specifically for washing machines.
WARNING: Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.
•Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.
•Use lesser detergent for small amounts or lightly soiled clothes.
Using softeners
Pour the softener into the softener compartment of the detergent drawer.
•Do not exceed the (>max<) level sign on the softener compartment.
•If the softener has lost its fluidity, dilute it with water before adding it in the detergent compartment.
A WARNING: Do not use liquid detergents or other cleaning products other than fabric softeners produced for washing machines to soften the clothes.
Washing Machine / User’s Manual |
9 / EN |
Using liquid detergents
If the product contains a liquid detergent cup:
•Put the liquid detergent container into the compartment no “2”.
•If the liquid detergent lost its fluidity, dilute it with water before putting it into the detergent container.
2
If the product is equipped with a liquid detergent part:
•When you want to use liquid detergent, pull the apparatus towards yourself. The part that falls down will serve as a barrier for the liquid detergent. If required, clean the apparatus with water when it is in place or by removing it. If you will use powder detergent, the apparatus must be secured at top position.
If the product does not contain a liquid detergent cup:
•Do not use liquid detergent for the prewash in a programme with prewash.
•Liquid detergent stains your clothes when used with "End Time" function to started delayed. If you are going
to use the End Time function, do not use liquid detergent.
Using gel and tablet detergent
•If the gel detergent thickness is fluidal and your product does not contain a special liquid detergent container, put the gel detergent into the main wash detergent compartment during first water intake. If your product contains a liquid detergent container, fill the detergent into this container before starting the programme.
•If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the drum before washing.
•Put tablet detergents into the main wash compartment (compartment no. "2") or directly into the drum
before washing.
Using starch
•Add liquid starch, powder starch or the dyestuff into the softener compartment.
•Do not use softener and starch together in a washing cycle.
•Wipe the inside of the product with a damp and clean cloth after using starch.
Using limescale remover
•When required, use limescale removers manufactured specifically for washing machines only.
Using bleaches
•Select a programme with prewash and add the bleach at the beginning of the prewash. Do not put detergent in the prewash compartment. As an alternative application, select a programme with extra rinse and add the bleach while the product is taking water from the detergent compartment during first rinsing step.
•Do not use bleach and detergent by mixing them.
•Use just a little amount (approx. 50 ml) of bleach and rinse the clothes very well as it causes skin irritation.
•Do not pour the bleach onto the laundry.
•Do not use it with the colored items.
•When using an oxygen-based bleach, select a program which washes the laundry at a low temperature.
•Oxygen-based bleach can be used together with the detergent. However, if its thickness is not the same with the detergent, put the detergent first into the compartment no. "2" in the detergent drawer and wait until the detergent flows while the product is taking in water. While the product continues taking in water, add bleach in the same compartment.
10 / EN |
Washing Machine / User’s Manual |
Loading...