The following instructions will help you
The Power of Being There
Quick Installation Guide
DSR® Switch
DSR1020 | DSR2020 | DSR4020 | DSR8020
to connect your DSR switch.
Should you require further assistance, please
consult your installer/user guide.
Connecting power to the
1
DSR switch
Power down all servers that will be part of your DSR
switching system. Locate the power cord that came
with the DSR switch. Plug one end into the power
socket on the rear of the DSR switch. Plug the other
end into an appropriate AC wall outlet.
Connecting the local port
2
Plug your VGA monitor, PS/2 or USB keyboard and
mouse cables into the appropriately labeled DSR ports.
Connecting a DSRIQ module to
3
the DSR switch
Choose an available port on the rear of your DSR
switch. Plug one end of a CAT 5 cable (4-pair, up to
10 meters) into a numbered port and plug the other
end into the RJ-45 connector of a DSRIQ module.
Connecting a server to the
4
DSRIQ module
Plug the DSRIQ module into the appropriate ports on
the back of the server. Repeat this procedure for all
servers that are to be connected to the DSR switch.
Connecting network and
5
remote users
Plug a CAT 5 cable from your Ethernet network into
the LAN connector on the back of your DSR switch.
Network users will access the DSR switch through
this port.
(Continued on reverse side)
To connect a DSR switch
5
Connect the switch
to the network.
Ethernet
1
Power down all
servers and attach
the appropriate
power cord to the
DSR switch.
A1
2
Plug in the
keyboard,
monitor and
mouse for your
local connection.
7
Connect your
SPC device to
the target servers.
SPC Power
Control Device
Modem
Local
Connections
Server
Server
Server
Server
Telephone
network
DSR Switch
1357
2468
91113
10 12
141516
6
Plug in the
external modem.
3
Connect DSRIQ
modules to the
DSR switch.
4
Connect servers
to the DSRIQ
modules.
8
Power up target
servers and then
the DSR switch.
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. ©2004 Avocent Corporation. All rights reserved. 590-420-603A
Quick Installation Guide
DSR® Switch
DSR1020 | DSR2020 | DSR4020 | DSR8020
The Power of Being There
The following instructions will help you
to connect your DSR switch.
Should you require further assistance, please
consult your installer/user guide.
Connecting an external
6
modem (optional)
The DSR switch may also be accessed using an
ITU V.92, V.90 or V.34-compatible modem. Plug one
end of a 9-pin serial cable into the MODEM connector
on the back of your DSR switch. Plug the other end
into the connector on the back of the modem.
NOTE: Using a modem connection instead of a
LAN connection will limit the performance capability
of your DSR switch.
7
Connecting the SPC device to the
DSR switch (optional)
Plug one end of the cable supplied with the SPC
power control device into the SPC connector on the
DSR switch and plug the other end into the SPC
device. Plug the power cords from the target servers
into the SPC power outlets. Plug the SPC device
into an appropriate AC wall outlet.
8
Powering up targets and switch
Power up each target server and then power up the
DSR switch.
For additional information
For further instructions on DSR switch connection,
software setup and security configuration, please
refer to the installer/user guide included with the
switch. Check http://register.avocent.com for the
latest DSR software and firmware updates.
To connect a DSR switch
(continued from reverse side)
5
Connect the switch
to the network.
Ethernet
Modem
1
Power down all
servers and attach
the appropriate
power cord to the
DSR switch.
A1
2
Plug in the
keyboard,
monitor and
mouse for your
local connection.
Local
Connections
7
Connect your
SPC device to
the target servers.
SPC Power
Control Device
Server
Server
Server
Telephone
Server
network
DSR Switch
1357
2468
91113
10 12
141516
6
Plug in the
external modem.
3
Connect DSRIQ
modules to the
DSR switch.
4
Connect servers
to the DSRIQ
modules.
8
Power up target
servers and then
the DSR switch.
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. ©2004 Avocent Corporation. All rights reserved.
The Power of Being There
1357
2468
A1
91113
10 12
141516
Loading...