ASRock J4105B-ITX operation manual

Version 1.0

Published October 2017

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/ perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 5

1.4 I/O Panel 7

Chapter 2 Installation 9

2.1 Installing Memory Modules (SO-DIMM) 10

2.2 Expansion Slot (PCI Express Slot) 12

2.3 Jumpers Setup 13

2.4 Onboard Headers and Connectors 14

Chapter 3 Software and Utilities Operation 18

3.1 Installing Drivers 18

3.2 ASRock Live Update & APP Shop 19

3.2.1 UI Overview 19

3.2.2 Apps 20

3.2.3 BIOS & Drivers 23

3.2.4 Setting 24

Chapter 4 UEFI SETUP UTILITY 25

4.1 Introduction 25

4.1.1 UEFI Menu Bar 25

4.1.2 Navigation Keys 26

4.2 Main Screen 27

4.3 Advanced Screen 28

4.3.1 CPU Conguration 29

4.3.2 Chipset Conguration 30

4.3.3 Storage Conguration 32

4.3.4 Super IO Conguration 33

4.3.5 ACPI Conguration 35

4.3.6 USB Conguration 37

4.4 Tools 38

4.5 Hardware Health Event Monitoring Screen 40

4.6 Security Screen 41

4.7 Boot Screen 42

4.8 Exit Screen 44

Chapter 1 Introduction

ank you for purchasing ASRock J4105B-ITX / J4005B-ITX motherboard, a

reliable motherboard produced under ASRock’s consistently stringent quality

control. It delivers excellent performance with robust design conforming to

ASRock’s commitment to quality and endurance.

In this manual, Chapter 1 and 2 contains the introduction of the motherboard

and step-by-step installation guides. Chapter 3 contains the operation guide of the

soware and utilities. Chapter 4 contains the conguration guide of the BIOS setup.

Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s website w ithout f urther notice. If you require technical support relate d to this motherboard, please vi sit our website for s pecic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website ht tp://www.a srock.com.

1.1 Package Contents

ASRock J4105B-ITX / J4005B-ITX Motherboard (Mini-ITX Form Factor)

•

ASRock J4105B-ITX / J4005B-ITX Quick Installation Guide

•

ASRock J4105B-ITX / J4005B-ITX Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x I/O Panel Shield

•

J4105B-ITX J4005B-ITX

English

1.2 Specications

Platform

CPU

Memory

Expansion Slot

•

* 2GB DRAM per module is not supported.

•

Mini-ITX Form Factor

Solid Capacitor design

Intel® Quad-Core Processor J4105 (up to 2.5 GHz)

(for J4105B-ITX)

Intel® Dual-Core Processor J4005 (up to 2.7 GHz)

(for J4005B-ITX)

Dual Channel DDR4 Memory Technology

2 x DDR4 SO-DIMM Slots

Supports DDR4 2400/2133 non-ECC, un-buered memory

Max. capacity of system memory: 8GB

1 x PCI Express 2.0 x16 Slot (PCIE1: x2 mode)

English

Graphics

• Integrated Intel® UHD Graphics 600: 12 EUs inside (Up to

750MHz) (for J4105B-ITX)

• Integrated Intel® UHD Graphics 600: 12 EUs inside (Up to

700MHz) (for J4005B-ITX)

• DX12, OpenGL 4.3, OGL ES 3.0, OpenCL 2.0

• HW Acceleration Decode: HEVC (H.265) 8 bit, HEVC

(H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8,

VP9 8bit, VP9 10 bit

• HW Acceleration Encode: HEVC (H.265) 8 bit, HEVC

(H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8,

VP9 8bit

• Dual graphics output: support D-Sub and HDMI ports by

independent display controllers

• Supports HDMI with max. resolution up to 4K x 2K

(4096x2160) @ 30Hz

• Supports D-Sub with max. resolution up to 2048x1536 @

60Hz

• Supports Auto Lip Sync, xvYCC and HBR (High Bit Rate

Audio) with HDMI Port (Compliant HDMI monitor is

required)

Audio

LAN

Rear Panel I/O

• Supports HDCP with HDMI Port

• Supports Full HD 1080p Blu-ray (BD) playback with HDMI

Port

7.1 CH HD Audio (Realtek ALC887 Audio Codec)

•

* To congure 7.1 CH HD Audio, it is required to use an HD

front panel audio module and enable the multi-channel audio

feature through the audio driver.

Supports Surge Protection

•

ELNA Audio Caps

•

PCIE x1 Gigabit LAN 10/100/1000 Mb/s

•

Realtek RTL8111H

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x PS/2 Mouse/Keyboard Port

•

1 x Parallel Port (ECP/EPP Support)

•

1 x Serial Port: COM1

•

1 x D-Sub Port

•

1 x HDMI Port

•

1 x USB 2.0 Port (Supports ESD Protection)

•

3 x USB 3.1 Gen1 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

•

J4105B-ITX J4005B-ITX

Storage

Connector

2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

•

Hot Plug

1 x COM Port Header

•

1 x Chassis Intrusion and Speaker Header

•

1 x CPU Fan Connector (3-pin)

•

1 x Chassis Fan Connector (3-pin)

•

1 x 24 pin ATX Power Connector

•

1 x Front Panel Audio Connector

•

English

BIOS Feature

Hardware Monitor

Certications

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD

•

Protection)

1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports)

•

(Supports ESD Protection)

* USB3_1_2 is shared with USB2_3.

AMI UEFI Legal BIOS with GUI support

•

Supports Plug and Play

•

ACPI 5.0 compliant wa ke up events

•

Supports jumperfree

•

SMBIOS 3.0 support

•

CPU/Chassis temperature sensing

•

CPU/Chassis Fan Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

•

CPU temperature)

CPU/Chassis Fan multi-speed control

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

•

Microso® Windows® 10 64-bit

•

FCC, CE

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

English

* For detailed product information, please visit our website: http://ww w.asrock.com

J4105B-ITX

PCIE1

ATXP WR 1

AUDIO CODEC

Sup er

I/O

DDR 4_ A1

DDR4_B1

CPU_FAN 1

USB2_3

HDLED RESET

PLED PWRB TN

PANEL1

COM2

SATA3_

CMO S

Bat te ry

Ro HS

HD_AU DIO1

BIOS

ROM

Fr on t US B 3 . 0

LAN

CLRMOS1

USB3_ 1_2

SATA3_1

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

USB4_5

HDM I1

PARALLE L PORT

COM1

VGA1

USB 3 .1 Gen 1

T: USB1

B: US B2

PS2

Key boar d/

Mous e

USB 3 .1 Ge n1:

USB4

RJ-4 5

USB 2 .0: U SB3

SPK_CI1

J4005B-ITX

1.3 Motherboard Layout

810

English

No. Description

1 CPU Fan Connector (CPU_FAN1)

2 ATX Power Connector (ATXPWR1)

3 System Panel Header (PANEL1)

4 Chassis Intrusion and Speaker Header (SPK_CI1)

5 Clear CMOS Jumper (CLRMOS1)

6 Chassis Fan Connector (CHA_FAN1)

7 2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A1, DDR4_B1)

8 COM Port Header (COM2)

9 USB 2.0 Header (USB4_5)

10 USB 3.1 Gen1 Header (USB3_1_2)

11 USB 2.0 Header (USB2 _3)

12 SATA3 Connector (SATA3_1)

13 SATA3 Connector (SATA3_2)

14 Front Panel Audio Header (HD_AUDIO1)

English

1.4 I/O Panel

1 2 3 5

J4105B-ITX J4005B-ITX

11 1012

No. Description No. Description

1 PS/2 Mouse/Keyboard Port 7 USB 2.0 Port (USB3_3)

2 Parallel Port 8 USB 3.1 Gen1 Port (USB3_4)

3 LAN RJ-45 Port* 9 HDMI Port

4 Line In (Light Blue)** 10 D-Sub Port

5 Front Speaker (Lime)** 11 COM Port

6 Microphone (Pink)** 12 USB 3.1 Gen1 Ports (USB3_1_2)

* ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK L ED

SPEED LE D

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

English

** To congure 7.1 CH HD Audio, it i s required to use an HD front panel audio module and enable the multichannel audio feature through the audio driver.

Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.

Function of the Audio Por ts in 7.1-channel Con guration:

English

Port Function

Light Blue (Rear panel) Rear Speaker Out Lime (Rear panel) Front Speaker Out Pink (Rear panel) Central /Subwoofer Speaker Out Lime (Front panel) Side Speaker Out

Chapter 2 Installation

is is a Mini-ITX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard.

•

Failure to do so may cause physical injuries to you and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

J4105B-ITX J4005B-ITX

English

2.1 Installing Memory Modules (SO-DIMM)

is motherboard provides two 260-pin DDR4 (Double Data Rate 4) SO-DIMM slots, and

supports Dual Channel Memory Technology.

1. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and SO-DIMM may be d amaged.

2. e SO-DIMM only ts in one correct orientation. It wil l cause permanent dam age to the motherboard and the SO -DIMM if you force the SO-DIM M into the slot at incorrect orientation.

Supported DDR4 Non ECC SODIMM

Raw Card

A (1Rx8) B (2Rx8) C (1Rx16)

Dual Channel Memory Conguration

English

DDR4_ A1

DDR4_B1

Populated

J4105B-ITX J4005B-ITX

English

+ 36 hidden pages