Asrock H97 Anniversary User Manual

H97 AnniversaryH97 Anniversary

H97 AnniversaryH97 Anniversary

Version 1.0

Published August 2014

Copyright©2014 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 6

1.4 I/O Panel 8

Chapter 2 Installation 10

2.1 Installing the CPU 11

2.2 Installing the CPU Fan and Heatsink 14

2.3 Installing Memory Modules (DIMM) 15

2.4 Expansion Slots (PCI Express Slots) 17

2.5 Jumpers Setup 18

2.6 Onboard Headers and Connectors 19

Chapter 3 Software and Utilities Operation 23

3.1 Installing Drivers 23

3.2 A-Tuning 24

3.3 Intel® Rapid Start Technology 30

3.4 Intel® Smart Connect Technology 35

3.5 ASRock APP Shop 40

3.5.1 UI Overview 40

3.5.2 Apps 41

3.5.3 BIOS & Drivers 44

3.5.4 Setting 45

3.6 Start8 46

Chapter 4 UEFI SETUP UTILITY 49

4.1 Introduction 49

4.1.1 UEFI Menu Bar 49

4.1.2 Navigation Keys 50

4.2 Main Screen 51

4.3 OC Tweaker Screen 52

4.4 Advanced Screen 60

4.4.1 CPU Conguration 61

4.4.2 Chipset Conguration 63

4.4.3 Storage Conguration 65

4.4.4 Intel® Rapid Start Technology 66

4.4.5 Intel® Smart Connect Technology 67

4.4.6 ACPI Conguration 68

4.4.7 USB Conguration 70

4.4.8 Trusted Computing 72

4.5 Tools 73

4.6 Hardware Health Event Monitoring Screen 76

4.7 Boot Screen 77

4.8 Security Screen 80

4.9 Exit Screen 81

H97 Anniversary

1

English

Chapter 1 Introduction

ank you for purchasing ASRock H97 Anniversary motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

In this manual, Chapter 1 and 2 contains the introduction of the motherboard

and step-by-step insta llation guides. Chapter 3 contains the operation guide of the

soware and utilities. Chapter 4 contains the conguration guide of the BIOS setup.

1.1 Package Contents

•

ASRock H97 Anniversary Motherboard (ATX Form Factor)

•

ASRock H97 Anniversary Quick Installation Guide

•

ASRock H97 Anniversary Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x I/O Panel Shield

Becau se the motherboard specications and th e BIOS soware mig ht be updated, the
content of this manual will be subject to change without notice. In case any modica­tions of this manual occur, the updated version will be available on ASRock’s website
without further notice. If you require technical suppor t related to this motherboard,
please visit our we bsite for spe cic information about the model you are using. You
may nd the l atest VGA cards and CPU support li st on ASRock’s website as well.
ASRock website http://www.asrock.com.

2

English

1.2 Specications

Platform

•

ATX Form Factor

•

Solid Capacitor design

•

High Density Glass Fabric PCB

CPU

•

Supports 5

th

Generation Intel® CoreTM i7/i5/i3/Pentium®/

Celeron® Processors (Socket 1150)

•

Supports New 4th and 4th Generation Intel® Xeon®/CoreTM i7/

i5/i3/Pentium®/Celeron® Processors (Socket 1150)

•

Digi Power design

•

4 Power Phase design

•

Supports Intel® Turbo Boost 2.0 Technology

Chipset

•

Intel® H97

Memory

•

Dual Channel DDR3 Memor y Technology

•

4 x DDR3 DIMM Slots

•

Supports DDR3 1600/1333/1066 non-ECC, un-buered

memory

•

Max. capacity of system memory: 32GB (see CAUTION)

•

Supports Intel® Extreme Memory Prole (X MP) 1.3 / 1.2

Expansion
Slot

•

1 x PCI Express 3.0 x16 Slot (PCIE2: x16 mode)

•

5 x PCI Express 2.0 x1 Slots

Graphics

•

Intel® HD Graphics Built-in Visuals and the VGA outputs can

be supported only with processors which are GPU integrated.

•

Supports Intel® HD Graphics Built-in Visuals : Intel® Quick

Sync Video with AVC, MVC (S3D) and MPEG-2 Full

HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD

Technology, Intel® InsiderTM, Intel® HD Graphics 4400/4600

•

Pixel Shader 5.0, DirectX 11.1

•

Max. shared memory 1792MB

•

ree graphics output options: D-Sub, DVI-D and HDMI

•

Supports Triple Monitor

H97 Anniversary

3

English

•

Supports HDMI with ma x. resolution up to 1920x1200 @

60Hz

•

Supports DVI-D with max. resolution up to 1920x1200 @

60Hz

•

Supports D-Sub with max. resolution up to 1920x1200 @

60Hz

•

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

HBR (High Bit Rate Audio) with HDMI Port (Compliant

HDMI monitor is required)

•

Supports HDCP with DVI-D and HDMI Ports

•

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

and HDMI Ports

Audio

•

5.1 CH HD Audio (Realtek ALC662 Audio Codec)

•

Supports Surge Protection (ASRock Full Spike Protection)

•

ELNA Audio Caps

LAN

•

PCIE x1 Gigabit LAN 10/100/1000 Mb/s

•

Realtek RTL8111GR

•

Su ppor ts Wa ke- On-WAN

•

Suppo rt s Wa ke-On-L AN

•

Supports Lightning/ESD Protection (ASRock Full SpikeProt-

ection)

•

Supports LAN Cable Detection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

Rear Panel
I/O

•

1 x PS/2 Mouse Port

•

1 x PS/2 Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

2 x USB 2.0 Ports (Supports ESD Protection (ASRock Full

Spike Protection))

•

4 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

Spike Protection))

4

English

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LE D)

•

HD Audio Jacks: Line in / Front Speaker / Microphone

Storage

•

6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology

13 and Intel Smart Response Technology), NCQ, AHCI and

Hot Plug

Connector

•

1 x TPM Header

•

1 x Power LED Header

•

2 x CPU Fan Connectors (1 x 4-pin, 1 x 3-pin)

•

2 x Chassis Fan Connectors (1 x 4-pin, 1 x 3-pin)

•

1 x Power Fan Connector (3-pin)

•

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x PCIe Power Connector

•

1 x Front Panel Audio Connector

•

1 x SPDIF Out Connector

•

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD

Protection (ASRock Full Spike Protection))

•

1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports ESD

Protection (ASRock Full Spike Protection))

BIOS
Feature

•

64Mb AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 1.1 Compliant wake up events

•

SMBIOS 2.3.1 support

•

CPU, DRAM, PCH 1.05V Voltage multi-adjustment

Hardware
Monitor

•

CPU/Chassis temperature sensing (Except for CHA_FAN2)

•

CPU/Chassis/Power Fan Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

CPU temperature) (Except for CHA_FAN2)

•

CPU/Chassis Fan multi-speed control (Except for CHA_

FAN 2)

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

OS

•

Microso® Windows®

10 64-bit /

8.1 32-bit / 8.1 64-bit / 8 32-

bit / 8 64-bit / 7 32-bit / 7 64-bit

H97 Anniversary

5

English

Certica­tions

•

FCC, CE, WHQL

•

ErP/EuP ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

Please realize that there is a certain risk involved with overclocking, including adjust­ing the setting in the BIOS , applying Untied Overclocking Technology, or u sing third­party o verclocking tools. Overclocking may aect your system’s stability, or even cause
damage to the components and dev ices of your system. It should be done at your own
risk and expense. We are not responsible for po ssible dam age caused by overclocking.

Due to limitation, the actual memory size may be less than 4GB for the rese rvation
for system usage und er Windows® 32-bit operating systems. Windows® 64-bit operat­ing systems do not have s uch limitations. You can use ASRock XFast RAM to utilize
the memory that Windows® cannot use.

6

English

1.3 Motherboard Layout

Intel

H97

DDR 3_A2 (6 4 bit, 24 0-pin m odule )

DDR 3_A1 (6 4 bit, 24 0-pin m odule )

DDR 3_B2 (6 4 bit, 24 0-pin m odule )

DDR 3_B1 (6 4 bit, 24 0-pin m odule )

ATX12V1

CMOS

Battery

Super

I/O

ATXP WR1

1

USB_10 _11

LAN

Top:
RJ-45

USB 2.0
T: USB2
B: USB3

CLRCMOS1

1

PLED1

1

1

SPEAKER1

HDLED RESET

PLED PWRBTN

PANEL1

1

USB_6_7

1

USB_8_9

1

1

HD_AUDIO1

H97 A nniversary

CHA_FAN1

RoHS

7

8

9

10

14

11
12

13

23

25

2

CPU_FAN1

CPU_FAN2

3

4

6

5

1

26

64Mb
BIOS

24

HDM I1

PWR_FAN1

SATA_5

SATA_4

SATA_3

SATA_2

SATA_1

SATA_0

PCIE3

USB 3.0
T: USB0
B: USB1

PCIE2

PCIE4

PCI Express 3.0

Fro nt USB 3. 0

Top:

LINE IN

Cente r:

FRONT

Botto m:

MIC IN

CHA_FAN2

PCIE1

PCIE_PWR1

1

TPMS1

VGA 1

DVI 1

PCIE5

PCIE6

SPDIF_OUT1

1

AUDIO

CODEC

PS2

Mouse

PS2

Keyb oard

USB 3.0
T: USB4
B: USB5

H97 Anniversary

7

English

No. Description

1 Power Fan Connector (PWR_FAN1)

2 ATX 12V Power Connector (ATX12V1)

3 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1)

4 2 x 240-pin DDR3 DIMM Slots (DDR3_A2, DDR3_B2)

5 ATX Power Connector (ATXPWR1)

6 USB 3.0 Header (USB_10_11)

7 Chassis Fan Connector (CHA_FAN2)

8 SATA3 Connector (SATA_1)

9 SATA3 Connector (SATA_0)

10 SATA3 Connector (SATA_3)

11 SATA3 Connector (SATA_2)

12 SATA3 Connector (SATA_5)

13 SATA3 Con nec tor (SATA_ 4)

14 Chassis Fan Connector (CHA_FAN1)

15 System Panel Header (PANEL1)

16 Power LED Header (PLED1)

17 USB 2.0 Header (USB_8_9)

18 USB 2.0 Header (USB_6_7)

19 TPM Header (TPMS1)

20 Chassis Speaker Header (SPEAKER1)

21 Clear CMOS Jumper (CLRCMOS1)

22 SPDIF Out Connector (SPDIF_OUT1)

23 Front Panel Audio Header (HD_AUDIO1)

24 CPU Fan Connector (CPU_FAN1)

25 PCIe Power Connector (PCIE_PWR1)

26 CPU Fan Connector (CPU_FAN2)

8

English

1.4 I/O Panel

No. Description No. Description

1 PS/2 Mouse Port (Green) 7 USB 3.0 Ports (USB_4_5)

2 D-Sub Port 8 USB 2.0 Ports (USB_2_3)

3 LAN RJ-45 Port* 9 USB 3.0 Ports (USB_0_1)

4 Line In (Light Blue) 10 HDMI Port

5 Front Speaker (Lime) 11 DVI-D Por t

6 Microphone (Pink) 12 PS/2 Keyboard Port (Purple)

6712 8911 10

1 2 3 5

4

H97 Anniversary

9

English

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indication s.

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Por t

10

English

is is an ATX form factor motherboard. Before you install the motherboard, study

the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

•

Make sure to unplug the power cord before installing or removing the motherboard

components. Failure to do so may cause physical injuries and damages to motherboard

components.

•

In order to avoid damage from static electricity to the motherboard’s components,

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

•

Hold components by the edges and do not touch the ICs.

•

Whenever you uninsta ll any components, place them on a grounded anti-static pad or

in the bag that comes with the components.

•

When placing screws to secure the motherboard to the chassis, please do not over-

tighten the screws! Doing so may damage the motherboard.

Chapter 2 Installation

H97 Anniversary

11

English

2.1 Installing the CPU

1. Before you insert the 1150-Pin CPU into the socket, please check if the P nP cap is on
the socket, if the CPU sur face is unclean, or if there are any bent pins in the socket.
Do not force to insert the CPU into the socket if above situation is found. Otherwise,
the CPU will be seriously damaged .

2. Unplug all power c ables before installing the CPU.

2

1

A

B

12

English

4

5

3

H97 Anniversary

13

English

Please save and replace the cover if the processor is removed. e cover must be placed
if you wish to return the motherboard for aer ser vice.

14

English

2.2 Installing the CPU Fan and Heatsink

1 2

C

P

U

_

FA

N

H97 Anniversary

15

English

2.3 Installing Memory Modules (DIMM)

is motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology.

Dual Channel Memory Conguration

e DIMM only ts in one cor rect orientation. It will c ause permanent damage to
the mothe rboard and the DIMM if you force the DIMM into the slot at incorrect
orientation.

Priority DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2

1 Populated Populated
2 Populated Populated
3 Populated Populated Populated Populated

1. For dual channe l conguration, you always need to install identical (the same

brand, speed, size and chip-type) DDR3 DIMM pairs.

2. It is unable to activate Dual Channel Memory Technology with only one or three
memory module installed.

3. It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot;
otherwise, thi s motherboard and DIMM may be dam aged.

16

English

1

2

3

H97 Anniversary

17

English

2.4 Expansion Slots (PCI Express Slots)

ere are 6 PCI Express slots on the motherboard.

PCIe slots:

PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

PCIE3 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE4 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE5 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE6 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.

Before installing an expansion card, ple ase make sure that the power supply is
switched o or the powe r cord is unplugged. Plea se read the documentation of the
expan sion card and mak e necessary hardware settings for the card before you start
the installation.

18

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper

is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(C LRC MO S1)

(see p.6, No. 21)

CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear

the CMOS right aer you update the BIOS. If you need to clear the CMOS when

you just nish updating the BIOS, you must boot up the system rst, and then shut

it down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed.

Clear CMOS

Default

H97 Anniversary

19

English

2.6 Onboard Headers and Connectors

System Panel Header

(9-pin PANE L1)

(see p.6, No. 15)

Connect the power

switch, reset switch and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

PWRBTN (Power Switc h):

Connec t to the power switch on the chassis front panel. You may cong ure the way to
turn o your system using the power switch.

RESET (Reset Switch):
Connec t to the reset switch on the chas sis front panel. Press the reset switch to restart
the computer if the computer freezes and fail s to perform a normal restart.

PLED (Syste m Power LED):
Connec t to the power status indicator on the chassis front panel. e LED i s on when
the system is operating. e LED keeps blinking whe n the system i s in S1/S3 sleep state.
e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on when
the hard dr ive is reading or w riting data.

e front panel desig n may dier by cha ssis. A front panel module mainly consi sts
of power s witch, reset switch, power LED, hard drive activity LED, speaker and etc.
When connecting your chassi s front panel module to this header, make sure the wire
assig nments and the pin assignments are matched correc tly.

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the heade rs and connectors
will cause permanent damage to the motherboard.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

1

GND

20

English

Power LED Header

(3-pi n PL ED1)

(see p.6, No. 16)

Please connect the chassis

power LED to this header

to

indicate the system’s

power status.

Serial ATA3 Connectors

(SATA_0:

see p.6, No. 9)

(SATA_1:

see p.6, No. 8)

(SATA_2:

see p.6, No. 11)

(SATA_3:

see p.6, No. 10)

(SATA_4:

see p.6, No. 13)

(SATA_5:

see p.6, No. 12)

ese six SATA3

connectors support SATA

data cables for internal

storage devices with up to

6.0 Gb/s data transfer rate.

USB 2.0 Headers

(9-pin USB_8_9)

(see p.6, No. 17)

(9-pin USB_6_7)

(see p.6, No. 18)

Besides two USB 2.0 ports

on the I/O panel, there

are two headers on this

motherboard. Each USB

2.0 header can support

two ports.

USB 3.0 Header

(19-pin USB_10_11)

(see p.6, No. 6)

Besides four USB 3.0

ports on the I/O panel,

there is one header on this

motherboard. Each USB

3.0 header can support

two ports.

Front Panel Audio Header

(9-pin HD_ AUDIO1)

(see p.6, No. 23)

is header is for

connecting audio devices

to the front audio panel.

SATA_1SATA_5 SATA_3

SATA_0SATA_4 SATA_2

1

PLED+

PLED+

PLED-

DUMMY

GND

GND

P+

P-

USB_PWR

P+

P-

USB_PWR

1

1

IntA_PB_D+

Dummy

IntA_PB_D-

GND

IntA_PB_SSTX+

GND

IntA_PB_SSTX-

IntA_PB_SSRX+

IntA_PB_SSRX-

VbusVbus

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

J _ S E N S E

O U T 2 _ L

1

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

H97 Anniversary

21

English

Chassis Speaker Header

(4-pi n SPEA KER1)

(see p.6, No. 20)

Please connect the chassis

speaker to this header.

Chassis and Power Fan

Connectors

(4-pin CHA_FAN1)

(see p.6, No. 14)

(3-pin CH A_FAN2)

(see p.6, No. 7)

(3-pi n PW R_ FAN1)

(see p.6, No. 1)

Please connect fan cables

to the fan connectors and

match the black wire to

the ground pin.

CPU Fan Connectors

(4-pin CPU_FAN1)

(see p.6, No. 24)

(3-pin CPU_FAN2)

(see p.6, No. 26)

is motherboard pro-

vides a 4-Pin CPU fan

(Quiet Fan) connector.

If you plan to connect a

3-Pin CPU fan, please

connect it to Pin 1-3.

1. High De nition Audio supports Jack Sensing, but the panel wire on the chassis must
suppor t HDA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.

2. If you use an AC’97 audio pan el, plea se install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_ R and Audio_L (LIN) to OUT2_ L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to
connec t them for the AC’97 audio panel.
E. To activate the front mic , go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.

GN

D

+12V

CHA_FAN_SPEED

F

AN_SPEED_CONTROL

1

+5V

DUMMY

DUMMY

SPEAKER

GND

CHA_FAN_SPEED

+12V

GN D
+ 12V
CPU_FAN_SPEED
FAN_SPEED_CONTRO

L

1
2
3
4

GND

CPU_FA

N_SPEED

FAN_VOLTAGE

22

English

1

GN D

SMB _DAT A_MAI N

LAD 2

LAD 1

GN D

S_P WRDW N #

SER IRQ #

GN

D

PC ICL K

PC IRST #

LAD 3

+3 V

LAD 0

+3V S B

GN D

FRA ME

SMB _CLK _MAIN

ATX Power Connector

(24-pin AT XPWR1)

(see p.6, No. 5)

is motherboard pro-

vides a 24-pin ATX power

connector. To use a 20-pin

ATX power supply, please

plug it along Pin 1 and Pin

13.

ATX 12V Power

Connector

(8-pin ATX12V1)

(see p.6, No. 2)

is motherboard pro-

vides an 8-pin ATX 12V

power connector. To use a

4-pin ATX power supply,

please plug it along Pin 1

and Pin 5.

PCIe Power Connector

(4-pi n PC IE_P WR1)

(see p.6, No. 25)

Please connect a 4 pin molex

power cable to this connector

when more than three

graphics cards are installed.

SPDIF Out

Connec tor

(2-pi n SPDIF_

OU T1)

(see p.6, No. 22)

Please connect the

SPDIF_OUT connector of

a HDMI VGA card to this

header with a cable.

TPM Header

(17-pin TPMS1)

(see p.6, No. 19)

is connector supports

Trusted Platform Module

(TPM) system, which can

securely store keys, digital

certicates, passwords,

and data. A TPM system

also helps enhance

network security, protects

digital identities, and

ensures platform integrity.

12

1

24

13

4

1

8

5

SPDIFOUT

GND

1