Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Java™ and all other Java-based marks are trademarks or registered trademarks of Oracle America, Inc. in the U.S. and other countries.
Microsoft®, Windows® and Windows Me® are registered trademarks of Microsoft Corporation; and Windows XP™ is a trademark of
Microsoft Corporation.
PICMG®, CompactPCI®, AdvancedTCA™ and the PICMG, CompactPCI and AdvancedTCA logos are registered trademarks of the PCI
Industrial Computer Manufacturers Group.
UNIX® is a registered trademark of The Open Group in the United States and other countries.
Notice
While reasonable efforts have been made to assure the accuracy of this document, Artesyn assumes no liability resulting from any
omissions in this document, or from the use of the information obtained therein. Artesyn reserves the right to revise this document
and to make changes from time to time in the content hereof without obligation of Artesyn to notify any person of such revision or
changes.
Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a URL to
an Artesyn website. The text itself may not be published commercially in print or electronic form, edited, translated, or otherwise
altered without the permission of Artesyn.
It is possible that this publication may contain reference to or information about Artesyn products (machines and programs),
programming, or services that are not available in your country. Such references or information must not be construed to mean that
Artesyn intends to announce such Artesyn products, programming, or services in your country.
Limited and Restricted Rights Legend
If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply
unless otherwise agreed to in writing by Artesyn.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in
Technical Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and
Documentation clause at DFARS 252.227-7014 (Jun. 1995).
Contact Address
Artesyn Embedded Technologies Artesyn Embedded Technologies
Marketing Communications
2900 S. Diablo Way, Suite 190
Tempe, Arizona 85282
6806800K37DAugust 2014Re-branded to Artesyn template.
No danger encountered. Pay attention to important
information
430/MITX-440-DVI-2E.
Sicherheitshinweise on page 113.
Added Declaration of Conformity on page26.
18
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
Introduction
1.1Features
The MITX-430 is a Mini-ITX motherboard based on the Intel® Atom™ D410 single-core or
D510 dual-core processor that offers improved processing and graphics performance over
existing Mini-ITX Intel Atom based products.
It is designed to allow easy, cost-effective replacement of the motherboard in a production
environment. There are two versions of MITX-430:
MITX-430 - Single core processor for low power consumption.
MITX-440-DVI-2E - Dual core processor with some additional features for higher
performance, which still retains the low power consumption.
MITX-430 uses the latest generation Unified Extensible Firmware Interface (UEFI) Basic Input
Output System (BIOS) from American Megatrends Inc (AMI). This manages the interaction
between the low-level hardware interfaces and the OS level in an efficient manner that
provides superior reliability.
Chapter 1
The following sections describe some of the key features of MITX-430 single core and MITX440-DVI-2E dual core processors.
1.1.1MITX-430
The following table lists the features of the single core processor board:
Table 1-1 Single Core Processor Board Features
FunctionFeatures
CPU (uFCBGA) Intel Pineview-D SC Processor (D410)
ChipsetIntel ICH8-M
Frequency: Pineview-D SC 1.66GHz with TDP less than 10W
Supports up to 4GB DDR2 SO-DIMM
Supports 667MHz
Integrated Graphic Process Unit
3rd generation graphics core, 400MHz render clock frequency
Supports one VGA
Supports one LVDS
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
19
Introduction
Table 1-1 Single Core Processor Board Features (continued)
FunctionFeatures
System BIOS featureOne piece 4MB SPI boot device
Super I/OW83627UHG-LF
RTCIntegrated in ICH8-M
Audio Audio on board (ALC888-GR-LF)
LAN10/100/1000M Ethernet PHY, Intel WG82567V
USBSupports 10 USB2.0 high speed ports (four rear, five on header, and one mini
Expansion slotsOne PCI-E x1 slot
Rear: Line-in, Line out, MIC-in
PCI-Express)
One Mini-PCIE card slot
One standard USB flash disk (2x5Pin, 2.54mmPitch)
Rear panel portsOne 2xUSB2.0 ports stack one LAN (RJ-45)
One 2xUSB2.0 stack connector
One vertical triple stack (MIC-in, Line-in, Line-out)
One stack PS/2 port
One e-SATA port
One VGA DSUB-15
One stacked dual DSUB-9 serial port
Power connectors24-pin ATX power connector
FanSupports two smart fans (4 Pin), one for CPU and one for System
Serial ATAsupports one e-SATA and two SATA ports
PATASupports one Mini-IDE (44Pin)
Hardware monitorVoltage, temperature, and fan speed control
WatchdogSupports 1-255s or 1-255m watchdog
Trusted Platform
Module
Power managementACPI1.0b compatible
COM PortSupports 6 COM ports (two to DSUB-9 in rear I/O region, one
Supports one TPM connector (2x10, 2.54mm Pin header)
Supports ATX power supply
RS-232/422/485 port, two Power COM, and one to 2x5Pin header)
20
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
Table 1-1 Single Core Processor Board Features (continued)
FunctionFeatures
LPT PortSupports one parallel port (2x13Pin Header)
Front panel2x5Pin header, supports power button, reset button, power LED, HDD LED,
GPIOSupports 4 GPI and 4 GPO
Board sizeMini-ITX 170mm x 170mm
1.1.2MITX-440-DVI-2E
The following table lists the features of the dual core processor board:
Introduction
and standby LED
6 Layers PCB
Table 1-2 Dual Core Processor Board Features
FunctionFeatures
CPU (uFCBGA) Intel Pineview-D DC Processor (D510)
Frequency: Pineview-D DC 1.66GHz with TDP less than 13W
Supports up to 4GB DDR2 SO-DIMM
Supports 667MHz
Integrated Graphic Process Unit
3rd generation graphics core, 400MHz render clock frequency
Supports one VGA
Supports one LVDS
Supports one DVI (derived from LVDS)
ChipsetIntel ICH8-M
System BIOS featureOne piece 4MB SPI boot device
Super I/OW83627UHG-LF
RTCIntegrated in ICH8-M
Audio Audio on board (ALC888-GR-LF)
Rear: Line-in, Line out, MIC-in
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
21
Introduction
Table 1-2 Dual Core Processor Board Features (continued)
FunctionFeatures
LAN10/100/1000M Ethernet PHY, Intel WG82567V
USBSupports 10 USB2.0 high speed ports (four rear, five on header, and one mini
Expansion slots One PCI-E x1 slot
Rear panel ports Two 2xUSB2.0 ports stack one LAN (RJ-45)
10/100/1000M Ethernet Controller, Intel WG82574L
PCI-Express)
One Mini-PCIE card slot
One standard USB flash disk (2x5Pin, 2.54mmPitch)
One vertical triple stack (MIC-in, Line-in, Line-out)
One stack PS/2 port
One e-SATA port
One VGA DSUB-15 stack DVI port
One stacked dual DSUB-9 serial port
22
Power connectors24-pin ATX power connector
FanSupports two smart fans (4 Pin), one for CPU and one for the system
Serial ATAsupports one e-SATA and two SATA ports
PATASupport one Mini-IDE (44Pin)
Hardware monitorVoltage, temperature, and fan speed control
WatchdogSupports 1-255s or 1-255m watchdog
Trusted Platform
Module
Power management ACPI1.0b compatible
COM PortSupports 6 COM ports (two to DSUB-9 in rear I/O region, one
LPT PortSupports one parallel port (2x13Pin Header)
Front panel2x5Pin Header, supports power button, reset button, power LED, HDD LED,
GPIOSupports 4 GPI and 4 GPO
Supports one TPM connector (2x10, 2.54mm Pin header)
Supports ATX power supply
RS-232/422/485 port, two power COM, and one to 2x5Pin header)
and standby LED
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
Table 1-2 Dual Core Processor Board Features (continued)
FunctionFeatures
Board sizeMini-ITX 170mm x 170mm
6 Layers PCB
1.2Standard Compliances
MITX-430/MITX-440-DVI-2E meets the following standards.
Table 1-3 Standard Compliances
StandardDescription
IEC 60950-1 General requirements of Safety-Part 1 of Information
Introduction
Technology Equipment.
EN55024 (EU) Limits and methods of measurements of immunity
characteristics of Information Technology Equipment.
FCC 47 CFR Part 15 Subpart B (US), Class BFederal Communications Commission Radio Frequency
Devices class B level requirements.
EN55022 Class B (EU) Limits and methods of measurements of radio
disturbance characteristics of Information Technology
Equipment.
AS/NZS CISPR 22 Class B (Australia/New
Zealand)
VCCI Class B (Japan)Voluntary Control Council for Interference by
Limits and methods of measurement of radio
disturbance characteristics of Information Technology
Equipment.
Information Technology Equipment.
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
23
Introduction
Figure 1-1Declaration of Conformity
E
C Declaration of Conformity
According to EN 17050-1:2004
Manufacturer’s Name:
Manufacturer’s Address:
Declares that the following product, in accordance with the requirements of 2004/108/EC, 2006/95/EC,
2011/65/EU and their amending directives,
Product:
Model Name/Number:
has been designed and manufactured to the following specifications:
As manufacturer we hereby declare that the product named above has been designed to comply with the relevant sections of the above referenced specifications. This product complies with the essential health and safety
requirements of the above specified directives. We have an internal production control system that ensures
compliance between the manufactured products and the technical documentation.
Artesyn Embedded Technologies
Embedded Computing
Zhongshan General Carton Box Factory Co. Ltd. No 62, Qi
Guan Road West, Shiqi District, 528400 Zhongshan City
Guangdong, PRC
Tom Tuttle, Manager, Product Testing Services Date (MM/DD/YYYY)
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
1.3Mechanical Data
The following table provides details about the dimensions and weight of the board:
Table 1-4 Mechanical Data
FeatureValue
Dimensions170mm x 170mm
Weight Dual core board: 353g
1.4Ordering Information
When ordering board variants or board accessories, use the order numbers given in the
following sections.
Introduction
Single core board: 325g
1.4.1Supported Board Models
The following board models are supported:
Table 1-5 Available Board Variants
Order NumberDescription
MITX-430 Single-core Intel Atom based Mini-ITX board with standard I/O.
MITX-440-DVI-2E Dual-core Intel Atom based Mini-ITX with standard and optional I/O.
1.4.2Board Accessories
The following accessories are shipped with the board:
Table 1-6 Available Board Accessories
Order NumberDescription
MITX-430Two COM cables, one SATA power cable, one SATA data cable
MITX-440-DVI-2E Two COM cables, one SATA power cable, one SATA data cable
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
25
Introduction
Table 1-6 Available Board Accessories (continued)
Order NumberDescription
MITX-430 One IO shield
MITX-440-DVI-2E One IO shield
1.5Product Identification
The following graphic shows the location of the serial number label on the board.
Figure 1-2Single Core Processor Board - Serial Number Location
26
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
Figure 1-3Dual Core Processor Board -Serial Number Location
Introduction
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
27
Introduction
28
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
Hardware Preparation and Installation
2.1Environmental and Power Requirements
The following environmental and power requirements are applicable to the motherboard.
2.1.1Environmental Requirements
You must make sure that the motherboard, when operated in your particular system
configuration, meets the environmental requirements specified below.
Operating temperatures refer to the temperature of the air circulating around the
motherboard and not to the component temperature.
Chapter 2
Product Damage
High humidity and condensation on surfaces cause short circuits.
Do not operate the product outside the specified environmental limits. Make sure the
product is completely dry and there is no moisture on any surface before applying power.
Overheating and Damage of the Product
Operating the product without forced air cooling can lead to overheating and thus damage
of the product.
When operating the product, make sure that forced air cooling is available in the shelf.
Table 2-1 Environmental Requirements
RequirementOperating Non-operating
o
Temperature0
Humidity10% to 90% non-condensing5% to 95% non condensing
Vibration0.01g^2/Hz at 5-500Hz random
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
C to 55oC with CPU cooler-40oC to 85oC
vibration
29
Hardware Preparation and Installation
Table 2-1 Environmental Requirements (continued)
RequirementOperating Non-operating
Shock20G peak (half sine)
Altitude-60 to 4000 m ASL
2.1.2Thermal Requirements
Table 2-2 Critical Temperature Spots
ItemThermal Dissipation Power (W)Maximum Allowable Temperature (0C)
11ms
CPUD510 <= 13W
D410 <= 10W
ICH8-M3W92 (Tc)
100 (Tj)
System Overheating
Cooling Vents
Improper cooling can lead to system damage and can void the manufacturer's warranty. To
ensure proper cooling and undisturbed airflow through the system do not obstruct the
ventilation openings of the system. Make sure that the fresh air supply is not mixed with hot
exhaust from other devices.
30
MITX-430/MITX-440-DVI-2E Installation and Use (6806800K37D)
Loading...
+ 88 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.